Oxide Ligands Research Articles

Manganese gluconate, A greener and more degradation resistant agent for H2S oxidation using liquid redox sulfur recovery process

Iron chelate liquid redox sulfur recovery (LRSR) has been one of the most frequently recommended technologies for the oxidation of H2S in natural gas into elemental sulfur, particularly when the acid gas has a high CO2/H2S molar ratio. The process is however known to suffer from extensive oxidative ligand degradation that results in high operational costs. Moreover, poor biodegradability or toxicity of the existing ligand has become a concern. In this research, we demonstrated that gluconate, a naturally greener ligand, when coupled with manganese as the metal, has considerable potential to be a better redox agent. Manganese gluconate solution was more resistant against ligand degradation compared with iron NTA. As required, aerated solution was capable of converting dissolved NaHS into elemental sulfur. At sufficiently high pH, manganese gluconate solutions were stable enough from precipitation of manganese hydroxide, carbonate, or sulfides. An equilibrium calculation has been developed to understand the precipitation behavior.

Redox-Active Ligand Assisted Catalytic Water Oxidation by a RuIV =O Intermediate.

Water splitting is one of the most promising solutions for storing solar energy in a chemical bond. Water oxidation is still the bottleneck step because of its inherent difficulty and the limited understanding of the O-O bond formation mechanism. Molecular catalysts provide a platform for understanding this process in depth and have received wide attention since the first Ru-based catalyst was reported in 1982. RuV =O is considered a key intermediate to initiate the O-O bond formation through either a water nucleophilic attack (WNA) pathway or a bimolecular coupling (I2M) pathway. Herein, we report a Ru-based catalyst that displays water oxidation reactivity with RuIV =(O) with the help of a redox-active ligand at pH 7.0. The results of electrochemical studies and DFT calculations disclose that ligand oxidation could significantly improve the reactivity of RuIV =O toward water oxidation. Under these conditions, sustained water oxidation catalysis occurs at reasonable rates with low overpotential (ca. 183 mV).

Redox‐Active Ligand Assisted Catalytic Water Oxidation by a RuIV=O Intermediate

AbstractWater splitting is one of the most promising solutions for storing solar energy in a chemical bond. Water oxidation is still the bottleneck step because of its inherent difficulty and the limited understanding of the O−O bond formation mechanism. Molecular catalysts provide a platform for understanding this process in depth and have received wide attention since the first Ru‐based catalyst was reported in 1982. RuV=O is considered a key intermediate to initiate the O−O bond formation through either a water nucleophilic attack (WNA) pathway or a bimolecular coupling (I2M) pathway. Herein, we report a Ru‐based catalyst that displays water oxidation reactivity with RuIV=(O) with the help of a redox‐active ligand at pH 7.0. The results of electrochemical studies and DFT calculations disclose that ligand oxidation could significantly improve the reactivity of RuIV=O toward water oxidation. Under these conditions, sustained water oxidation catalysis occurs at reasonable rates with low overpotential (ca. 183 mV).

Zinc complexes supported by pyridine-N-oxide ligands: synthesis, structures and catalytic Michael addition reactions.

New dipyridylpyrrole N-oxide ligands HL1 and HL2 are designed and synthesized via oxidation of 2-(5-(pyridin-2-yl)-1H-pyrrol-2-yl)pyridine (Hdpp) by using 3-chloroperbenzoic acid (m-CPBA) in CH2Cl2. The treatment of ZnEt2 with two equiv. of HL1 and HL2 affords [Zn(L1)2] and [Zn(L2)2] in medium yield, respectively. These ligands and zinc complexes are fully characterized by NMR, IR, UV-vis and ESI-MS spectroscopy and X-ray diffraction analysis. The structure of HL1 and HL2 shows a planar geometry. The intramolecular hydrogen-bond interactions between the imino hydrogen and N-oxide oxygen atom are observed. In [Zn(L1)2] and [Zn(L2)2], two ligands chelate to the zinc metal with a cross perpendicular geometry. The zinc complexes were employed as a highly efficient catalyst for the thiol-Michael addition of thiols to α,β-unsaturated ketones in EtOH at room temperature. The loading of the catalyst is lowered to 0.01 mol%. The catalytic mechanism was proposed based on NMR and ESI-MS experiments.

Six-coordinate mononuclear dysprosium(iii) single-molecule magnets with the triphenylphosphine oxide ligand.

Structural, magnetic and theoretical studies of three octahedral mononuclear DyIII complexes with triphenylphosphine oxide and halide ligands are reported. The Cl- and Br- analogues exhibit SMM behavior with energy barriers of 49.1 K and 70.9 K, respectively under a small dc field. Ab initio calculations were performed, the results of which predict higher energy barriers for iodide containing SMMs.

Oxidative C-N bond cleavage of (2-pyridylmethyl)amine-based tetradentate supporting ligands in ternary cobalt(ii)-carboxylate complexes.

Three mononuclear cobalt(ii)-carboxylate complexes, [(TPA)CoII(benzilate)]+ (1), [(TPA)CoII(benzoate)]+ (2) and [(iso-BPMEN)CoII(benzoate)]+ (3), of N4 ligands (TPA = tris(2-pyridylmethyl)amine and iso-BPMEN = N1,N1-dimethyl-N2,N2-bis((pyridin-2-yl)methyl)ethane-1,2-diamine) were isolated to investigate their reactivity toward dioxygen. Monodentate (η1) binding of the carboxylates to the metal centre favours the five-coordinate cobalt(ii) complexes (1-3) for dioxygen activation. Complex 1 slowly reacts with dioxygen to enable the oxidative decarboxylation of the coordinated α-hydroxy acid (benzilate). Prolonged exposure of the reaction solution of 2 to dioxygen results in the formation of [(DPA)CoIII(picolinate)(benzoate)]+ (4) and [CoIII(BPCA)2]+ (5) (DPA = di(2-picolyl)amine and HBPCA = bis(2-pyridylcarbonyl)amide), whereas only [(DPEA)CoIII(picolinate)(benzoate)]+ (6) (DPEA = N1,N1-dimethyl-N2-(pyridine-2-ylmethyl)-ethane-1,2-diamine) is isolated from the final oxidised solution of 3. The modified ligand DPA (or DPEA) is formed via the oxidative C-N bond cleavage of the supporting ligands. Further oxidation of the -CH2- moiety to -C([double bond, length as m-dash]O)- takes place in the transformation of DPA to HBPCA on the cobalt(ii) centre. Labelling experiments with 18O2 confirm the incorporation of oxygen atoms from molecular oxygen into the oxidised products. Mixed labelling studies with 16O2 and H2O18 strongly support the involvement of water in the C-N bond cleavage pathway. A comparison of the dioxygen reactivity of the cobalt complexes (1-3) with those of several other five-coordinate mononuclear complexes [(TPA)CoII(X)]+/2+ (X = Cl, CH3CN, acetate, benzoylformate, salicylate and phenylpyruvate) establishes the role of the carboxylate co-ligands in the activation of dioxygen and subsequent oxidative cleavage of the supporting ligands by a metal-oxygen oxidant.

Intense red luminescent materials of ternary Eu3+ complexes of oxide ligands for electroluminescent display devices

Solid ternary compounds of Eu(III) with fluorinated β-diketone (4,4,5,5,6,6,6-heptafluoro-1-(2-thienyl)-1,3-hexanedione) (Hfth) and heteroaromatic monodentate ancillary ligands (aqua/triphenylphosphineoxide/pyridine-N-oxide/2-pyridionl-N-Oxide) were prepared for red color emissive materials. The luminescence characteristics of prepared compounds were illustrated using absorption and emission spectral measurements which specified that the β-diketone ligand could effectively sensitized the central europium ion meant for the improved emission of the light. Due to interaction metal complexes displays distinguished effectual on photoluminescence efficacy (η) as well as Judd Ofelt luminous factor (Ω2). An extensive relative approach of enhancement in luminescent behavior of the synthesized metal complexes had been carried out by replacing aqua ligand in the inner coordination sphere of conventionally prepared parent aqua complex with others ancillary oxide ligands to make metal complex co-coordinatively saturated as well as suitable for fabricating electroluminescent display devices.

Insight into the influence of terminal ligands on magnetic exchange coupling in a series of dimeric copper(II) acetate adducts

AbstractA combination of experimental (SQUID magnetometry) and quantum‐chemical (BS‐DFT, CASSCF(n,m)/NEVPT2, DDCI3) methods is used to probe the influence of terminal ligands on magnetic exchange coupling in the series of [Cu2(μ2‐OAc)4L2] complexes with O‐donor terminal ligands extended by two novel complexes containing phosphine oxide ligands. The possibilities and limitations of these approaches are discussed. The influence of terminal ligands on magnetic superexchange interaction was quantified by two contributions—the first contribution is associated with structural changes within the {Cu(μ2‐OAc)4Cu} core, while the second contribution is due to the difference in the electronic influence of different terminal ligands at a given core geometry. Both contributions were found to be approximately of the same order of magnitude. These results indicate that magnetic exchange coupling, known to be highly sensitive to the distortions in core geometry, is not solely determined by the core structure. Our findings are consistent with the fact that various one‐ and multiparameter magnetostructural correlations reported in the literature have only a qualitative predictive capability.

Catalytic oxidation of cyclic hydrocarbons with hydrogen peroxide using Fe complexes immobilized into montmorillonite

• Three different Fe complexes immobilized into montmorillonite. • Oxidation of cyclohexane and benzene with H 2 O 2 . • Effect of ligand for oxidation of cyclic hydrocarbons. • Effect of π-π stacking interaction between ligand and substrate. • Catalytic performance for oxidation of benzene in CH 3 CN and H 2 O mixed solvent. [Fe(Ligand) x ] 2+ complexes immobilized into montmorillonite ([Fe(Ligand) x ] 2+ @Mont, Ligand: 2,2′;6′,2′'-terpyridine (x = 2), 1,10-phenanthroline (x = 3), and 2,2′-bipyridine (x = 3)) were prepared by an ion-exchange method whereby cations present within montmorillonite (probably Ca 2+ ) were replaced by [Fe(Ligand) x ] 2+ complexes provided by [Fe(Ligand) x ](ClO 4 ) 2 . The catalytic properties of the species obtained were then investigated in the oxidation of cyclic hydrocarbons, such as cyclohexane and benzene, with H 2 O 2 . The catalytic oxidation of cyclohexane and benzene with H 2 O 2 over [Fe(Ligand) x ] 2+ @Mont catalysts proceeded, and the desired alcohols were obtained as the main reaction products, whereas no catalytic activity was displayed by neat montmorillonite. Regardless of the reaction conditions, [Fe(terpy) 2 ] 2+ @Mont (terpy stands for 2,2′;6′,2′'-terpyridine) exhibited the best catalytic performance in the oxidation of the mentioned substrates by H 2 O 2 , among all the catalysts tested.

Iron complexes with polydentate phosphines as unusual catalysts for alcohol oxidation

The iron(II) compounds [Fe(triphos)(CH3CN)3](OTf)2 (triphos = 1,1,1-tris(diphenylphosphinomethyl)ethane; OTf = CF3SO3) (1), [Fe(dppm)2(CH3CN)2](OTf)2 (dppm = bis(diphenylphosphino)methane) (2), [Fe(dppe)2(CH3CN)2](OTf)2 (dppe = 1,2-bis(diphenylphosphino)ethane) (3), [Fe(dppp)(CH3CN)4](OTf)2 (dppp = 1,3-bis(diphenylphosphino)propane) (4) and [Fe(PSP)(CH3CN)3](OTf)2 (PSP = bis(2-(diphenylphosphino)ethyl)sulfide) (5) were synthesized and characterized by NMR and (2, 3 and 4) also by X-ray crystallography. Such complexes catalyzed the selective oxidation of primary and secondary alcohols to the corresponding aldehydes and ketones. The catalytic reactions were performed in acetonitrile in mild experimental conditions (r.t. or 50 °C) using tert-butylhydroperoxide (TBHP) as oxidizing agent. By following the reaction of complex 4 with the oxidant by UV–visible spectroscopy, it was possible to evidence formation of the corresponding iron-peroxide intermediate. Comparison of ESI-MS spectra acquired on a solution of 1 or 4 before and after TBHP addition suggests ligand oxidation to iron-phosphine oxide complexes.

Room Temperature Synthesis of Phosphine‐Capped Lead Bromide Perovskite Nanocrystals without Coordinating Solvents

AbstractThe room temperature synthesis of perovskite nanocrystals (NCs) is typically achieved by employing a ligand‐assisted reprecipitation (LARP) method, which can be handled in air, and its products are comparable to what is obtained using the traditional hot‐injection method. However, the LARP method typically requires the use of coordinating polar solvents such as dimethylformamide, which are not appropriate for large‐scale production due to toxicity concerns and can also degrade or form defective perovskite NCs. Herein, an amine and oleic‐acid‐free room temperature synthesis of lead bromide perovskite NCs is reported that uses a combination of trioctylphosphine oxide and diisooctylphosphinic acid ligands. This combination of ligands provides a stable platform for the polar‐solvent‐free synthesis in air of fully inorganic CsPbBr3 (fwhm ≈ 14 nm, emission = 519 nm) and hybrid organic‐inorganic FAPbBr3 (fwhm ≈ 19 nm) NCs with photoluminescence emission between 530 and 535 nm, which is in line with the Rec. 2020 color standards. In addition, it is shown that compared to a traditionally used ligand combination, phosphine ligands can be easily removed from the surface of the NCs, which is important for the future development of this technology in optoelectronic devices.

Vibrational Quenching in Near-Infrared Emitting Lanthanide Complexes: A Quantitative Experimental Study and Novel Insights.

Two series of novel NIR-emissive complexes of Nd3+ , Sm3+ , Er3+ and Yb3+ with two different β-diketonate ligands (L1 =4,4,4-trifluoro-1-phenyl-1,3-butadione and L2 =4,4,4-trifluoro-1-(4-chlorophenyl)-1,3-butadione) are reported. The neutral triphenylphosphine oxide (tppo) ligand was used to replace coordinated water molecules in the first coordination sphere of the as-obtained [Ln(L1(2) )3 (H2 O)2 ] complexes to afford water-free [Ln(L1(2) )3 (tppo)2 ] molecular species. Upon replacement of water molecules by tppo units, the NIR emission lifetimes of the Nd3+ , Er3+ and Sm3+ complexes increase by about one order of magnitude up to values of ≈9, 8 and 113 ms while Yb3+ complexes reach intrinsic quantum yields as high as to ΦYb =6.5 %., which are remarkably high for fully hydrogenated complexes. Vibrational quenching by CH and OH oscillators has been quantitatively assessed by implementing the Förster's model of resonance energy transfer on the basis of experimental data. This study demonstrates that highly efficient NIR-emitting lanthanide complexes can be obtained with facile, cheap and accessible syntheses through a rational design.

Bioinspired oxidation of oximes to nitric oxide with dioxygen by a nonheme iron(II) complex.

The ability of two iron(II) complexes, [(TpPh2)FeII(benzilate)] (1) and [(TpPh2)(FeII)2(NPP)3] (2) (TpPh2 = hydrotris(3,5-diphenylpyrazol-1-yl)borate, NPP-H = α-isonitrosopropiophenone), of a monoanionic facial N3 ligand in the O2-dependent oxidation of oximes is reported. The mononuclear complex 1 reacts with dioxygen to decarboxylate the iron-coordinated benzilate. The oximate-bridged dinuclear complex (2), which contains a high-spin (TpPh2)FeII unit and a low-spin iron(II)-oximate unit, activates dioxygen at the high-spin iron(II) center. Both the complexes exhibit the oxidative transformation of oximes to the corresponding carbonyl compounds with the incorporation of one oxygen atom from dioxygen. In the oxidation process, the oxime units are converted to nitric oxide (NO) or nitroxyl (HNO). The iron(II)-benzilate complex (1) reacts with oximes to afford HNO, whereas the iron(II)-oximate complex (2) generates NO. The results described here suggest that the oxidative transformation of oximes to NO/HNO follows different pathways depending upon the nature of co-ligand/reductant.Graphic abstract.

Partial Oxidation-Induced Electrical Conductivity and Paramagnetism in a Ni(II) Tetraaza[14]annulene-Linked Metal Organic Framework.

We report the synthesis and characterization of a two-dimensional (2D) conjugated Ni(II) tetraaza[14]annulene-linked metal organic framework (NiTAA-MOF) where NiTAA is a macrocyclic MN4 (M = metal, N = nitrogen) compound. The structure of NiTAA-MOF was elucidated by Fourier-transform infrared, X-ray photoemission, and X-ray diffraction spectroscopies, in combination with density functional theory (DFT) calculations. When chemically oxidized by iodine, the insulating bulk NiTAA-MOF (σ < 10-10 S/cm) exhibits an electrical conductivity of 0.01 S/cm at 300 K, demonstrating the vital role of ligand oxidation in the electrical conductivity of 2D MOFs. Magnetization measurements show that iodine-doped NiTAA-MOF is paramagnetic with weak antiferromagnetic coupling due to the presence of organic radicals of oxidized ligands and high-spin Ni(II) sites of the missing-linker defects. In addition to providing further insights into the origin of the induced electrical conductivity in 2D MOFs, both pristine and iodine-doped NiTAA-MOF synthesized in this work could find potential applications in areas such as catalase mimics, catalysis, energy storage, and dynamic nuclear polarization-nuclear magnetic resonance (DNP-NMR).

A Rare Type of Rhenium(I) Diimine Complexes with Unsupported Coordinated Phosphine Oxide Ligands: Synthesis, Structural Characterization, Photophysical and Theoretical Study

This paper presents synthesis and photophysical investigation of a very rare type of the ReI diimine complexes, [Re(diimine)(CO)3(OPR3)]+, R = Ph, Cy; diimine – phenanthroline and neocuproine, containing monodentate (unsupported) phosphine oxide ligands. The obtained compounds have been structurally characterized in solid phase by using XRD crystallography, which revealed unusual distortions in the pseudo octahedral rhenium environment, which may be ascribed to intramolecular interligand (phosphine oxide – diimine) interaction rather than to crystal packing effect. Optimization of the ground state structure of these molecules with the DFT method also confirmed intramolecular origin of the observed structural peculiarities. The complexes display phosphorescence in solution and in solid state with the quantum yield up to 11 % and 14 %, respectively, which originates from 3MLCT excited state as demonstrated by DFT calculations. Comparative analysis of the ligand (L) effect onto emission energy in the [Re(neocuproine)(CO)3(L)] complexes (L = PPh3, NCMe, OPPh3, Cl–) showed that the position of emission wavelength in the corresponding complexes qualitatively correlates with cumulative donor ability of these ligands that is in complete agreement with the 3MLCT character of emission.

Mononuclear Ru(II) Complexes of an Arene and Asymmetrically Substituted 2,2'-Bipyridine Ligands: Photophysics, Computation, and NLO Properties.

By using monosubstituted 2,2'-bipyridine asymmetric ancillary ligands with different electron donor moieties and an arene ligand (p-cymene), we successfully designed and synthesized six Ru(II) compounds (RuBPY1-6) that belong to a piano-stool-type system. The NLO properties of the synthesized complexes have been studied in both solution and the solid state. The electronic spectra of these compounds show a broad feature with two absorption bands in the visible window (350-650 nm). RuBPY1-6 complexes exhibit NIR emission spectra in the solution state (at >720 nm), the maxima of which are bathochromically shifted in comparison to those of the concerned ligands. Interestingly, compounds RuBPY1-6 show NIR emission in their solid state too. Title compounds RuBPY1-6 have lifetimes in the range of 0.2 to 0.9 ns. An important feature of this work is the π-association of the p-cymene ligand to Ru(II) in the synthesized complexes; the π complex is formed by breaking the symmetry of p-cymene, found in the starting precursor (Ru2 dimer). This has been established by NMR spectral studies along with DFT calculations on the 1H NMR spectra. We could derive the molecular structure of the cationic part of this system by density functional theory (DFT), associated with 1H NMR spectral studies. The minimum energy structures for RuBPY1 and RuBPY2 have been optimized at DFT/B3LYP along with the LANL2DZ basis set for ruthenium atoms. These optimized structures are further considered to calculate the excited state properties using the TDDFT method. The electrochemical studies of the complexes, investigated in acetonitrile solution, show that this system is associated with a well-defined Ru(III)/Ru(II) reversible couple, rarely observed for a Ru(II) piano-stool-type compound, along with a feature of irreversible ligand oxidation. The absorption cross-section values, obtained from the two-photon absorption studies of title compounds RuBPY1-6, are worth reporting and lie in the range of 3-28 GM (in the femtosecond case).

Identification of nitrite treated tuna fish meat via the determination of nitrous oxide by head space-gas chromatography/mass spectrometry.

Tuna fish meat is an expensive and highly perishable sea food. Fresh meat has a bright red colour which soon turns into an unsightly brown during storage. To prolong the aspect of freshness, the red colour is stabilised or even enhanced e.g. with carbon monoxide or nitric oxide, the product of a nitrite / ascorbic acid treatment, which bind as a ligand to myoglobin. These procedures are illegal. Here we present a method for identifying tuna meat samples, which have undergone fraudulent wet salting with nitrite. The method uses headspace-gas chromatography/mass spectrometry (GC/MS) for the determination of nitrous oxide, which is formed as the final product of the two-step reduction nitrite (added agent) to nitric oxide (ligand) to nitrous oxide (target compound). Complex bound nitric oxide is set free with sulfuric acid, which also promotes the reduction to nitrous oxide. The method was validated using 15N labelled nitrite as well as treated and untreated reference fish samples. A survey of 13 samples taken from the Swiss market in 2019 showed that 45% of all samples were illegally treated with nitrite.

A Hydrophilic Channel Is Involved in Oxidative Inactivation of a [NiFeSe] Hydrogenase

Hydrogenases are metalloenzymes that catalyze the redox conversion between H2 and protons. The so-called [NiFeSe] hydrogenases are highly active for both H2 production and oxidation, but like all hydrogenases, they are inhibited by O2. In the [NiFeSe] enzyme from Desulfovibrio vulgaris Hildenborough this inhibition results from the oxidation of an active site cysteine ligand. We designed mutations that constrict a hydrophilic channel which connects the protein surface to this active site cysteine. Two of the variants show markedly increased tolerance to O2 inactivation, while they retain high catalytic activities in both directions of the reaction, and structural studies confirm that these mutations prevent the oxidation of the cysteine. Our results indicate that the diffusion of O2 or ROS to the active site can occur through a hydrophilic water channel, in contrast to the widely held assumption that only hydrophobic channels are involved in active site inactivation. This provides an original strategy for optimizing the enzyme by protein engineering.

An overly anionic metal coordination environment eliminates the T1-weighted response of quinol-containing MRI contrast agent sensors to H2O2

A previously reported quinol- and Mn(II)-containing MRI contrast agent sensor for H2O2 has the drawback of releasing the metal ion upon oxidation of the organic ligand. The release of potentially neurotoxic Mn(II) limits the sensor’s in vivo applicability. We prepared N,N′-bis(2,5-dihydroxybenzyl)ethanediamine-N,N′-diacetic acid (H6qc1) as a substitute ligand that could potentially remain bound to the metal ion after oxidation of the quinol portions to more weakly metal-binding para-quinones. The carboxylic acid groups deprotonate at ambient pH, providing a more anionic coordination environment that stabilizes its Mn(II) complex in water. Although the more anionic coordination sphere doesn’t introduce air sensitivity, it does render the metal center more susceptible to oxidation by hydrogen peroxide, as evidenced by electron paramagnetic resonance. The oxidation of the metal to less paramagnetic Mn(III) is proposed to lower the r1 enough to completely counter any increase in T1-weighted relaxivity that would result from improved aquation.

Polymerization of conjugated dienes and olefins promoted by cobalt complexes supported by phosphine oxide ligands

Four cobalt complexes supported by phosphine oxide (P=O) donors (9,9-dimethyl-9H-xanthene-4,5-diyl)bis(diphenylphosphine oxide) cobalt dichloride (Co1), (9,9-dimethyl-9H-xanthene-4,5-diyl)bis(diphenylphosphine oxide) cobalt bromide (Co2), N, N'-(pyridine-2,6-diyl)bis(P,P-di-tert-butylphosphinic amide) cobalt dichloride (Co3) and N, N'-(pyridine-2,6-diyl)bis(P,P-di-tert-butylphosphinic amide) cobalt dichloride (Co4) were prepared and characterized. Their catalyses performances in polymerization of isoprene, butadiene, myrcene as well as MMA and styrene were examined. In combination with AlEt2Cl, Co1 and Co2 are able to convert isoprene to polyisoprene, whereas the activities of Co3 and Co4 are much low. The resultant polyisoprene are mixture of cis-1,4 and 3,4 isomers, whose ratio are not significantly affected by the type of catalysts and polymerization conditions. Isoprene was found to be more active than myrcene, and butadiene in the case of Co1/AlEt2Cl, suggestive of compromised sterical and electronic effect from the alkyl group at 2-positon of monomers. The Co1/AlEt2Cl system is also moderately active in polymerizations of methyl methacrylate and styrene. Therefore, the current catalysts provided dual polymerization reactivities towards conjugated dienes and olefins that are rare in transition metals catalyzed coordinative polymerization.