Lidar-Radiometer Inversion Code Research Articles

Evaluation of LIRIC Algorithm Performance Using Independent Sun-Sky Photometer Data at Two Altitude Levels

This work evaluates the Lidar-Radiometer Inversion Code (LIRIC) using sun-sky photometers located at different altitudes in the same atmospheric column. Measurements were acquired during an intensive observational period in summer 2012 at Aerosols, Clouds, and Trace gases Research InfraStructure Network (ACTRIS)/Aerosol Robotic Network (AERONET) Granada (GRA; 37.16°N, 3.61°W, 680 m above sea level (a.s.l.)) and Cerro Poyos (CP; 37.11°N, 3.49°W, 1820 m a.s.l.) sites. Both stations operated AERONET sun-photometry, with an additional lidar system operating at Granada station. The extended database of simultaneous lidar and sun-photometry measurements from this study allowed the statistical analysis of vertically resolved microphysical properties retrieved with LIRIC, with 70% of the analyzed cases corresponding to mineral dust. Consequently, volume concentration values were 46 μm3/cm3 on average, with a value of ~30 μm3/cm3 corresponding to the coarse spheroid mode and concentrations below 10 μm3/cm3 for the fine and coarse spherical modes. According to the microphysical properties’ profiles, aerosol particles reached altitudes up to 6000 m a.s.l., as observed in previous studies over the same region. Results obtained from comparing the LIRIC retrievals from GRA and from CP revealed good agreement between both stations with differences within the expected uncertainties associated with LIRIC (15%). However, larger discrepancies were found for 10% of the cases, mostly due to the incomplete overlap of the lidar signal and/or to the influence of different aerosol layers advected from the local origin located between both stations, which is particularly important in cases of low aerosol loads. Nevertheless, the results presented here demonstrate the robustness and self-consistency of LIRIC and consequently its applicability to large databases such as those derived from ACTRIS-European Aerosol Research Lidar Network (EARLINET) observations.

GARRLiC and LIRIC: strengths and limitations for the characterization of dust and marine particles along with their mixtures

Abstract. The Generalized Aerosol Retrieval from Radiometer and Lidar Combined data algorithm (GARRLiC) and the LIdar-Radiometer Inversion Code (LIRIC) provide the opportunity to study the aerosol vertical distribution by combining ground-based lidar and sun-photometric measurements. Here, we utilize the capabilities of both algorithms for the characterization of Saharan dust and marine particles, along with their mixtures, in the south-eastern Mediterranean during the CHARacterization of Aerosol mixtures of Dust and Marine origin Experiment (CHARADMExp). Three case studies are presented, focusing on dust-dominated, marine-dominated and dust–marine mixing conditions. GARRLiC and LIRIC achieve a satisfactory characterization for the dust-dominated case in terms of particle microphysical properties and concentration profiles. The marine-dominated and the mixture cases are more challenging for both algorithms, although GARRLiC manages to provide more detailed microphysical retrievals compared to AERONET, while LIRIC effectively discriminates dust and marine particles in its concentration profile retrievals. The results are also compared with modelled dust and marine concentration profiles and surface in situ measurements.

A sensitivity study of the LIdar-Radiometer Inversion Code (LIRIC) using selected cases from Thessaloniki, Greece database

ABSTRACTWe investigate the uncertainty introduced to the optical and microphysical properties estimated with the lidar radiometer inversion code (LIRIC) by user-defined input parameters based on measurements carried out with a multi-wavelength Raman lidar and a sun photometer located at Thessaloniki, Greece (40.6° N, 22.9° E, 60 m above sea level). The sensitivity study involves three tests. We first evaluate the selection of the regularization parameters needed for the algorithm to initialize the iteration process. The latter two tests consider the impact of the boundary limits at the top/bottom (upper/lower limit) of the signal to the derived concentration profiles. The aforementioned tests were applied to two different cases, a Saharan dust event and a continental pollution case. We concluded that the largest uncertainties are introduced when varying the lower limit (more than 35%) regardless of the aerosol type or mode (fine/coarse). Varying the regularization parameters resulted in an uncertainty of 20%, and the selection of upper limit led to discrepancies of less than 3%. In conclusion, this sensitivity study indicates that future LIRIC users should apply an overlap function to the lidar signals before applying the methodology for minimizing the uncertainties in the near range.

Investigating the quality of modeled aerosol profiles based on combined lidar and sunphotometer data

Abstract. In this study we present an evaluation of the Comprehensive Air Quality Model with extensions (CAMx) for Thessaloniki using radiometric and lidar data. The aerosol mass concentration profiles of CAMx are compared against the PM2.5 and PM2. 5−10 concentration profiles retrieved by the Lidar-Radiometer Inversion Code (LIRIC). The CAMx model and the LIRIC algorithm results were compared in terms of mean mass concentration profiles, center of mass and integrated mass concentration in the boundary layer and the free troposphere. The mean mass concentration comparison resulted in profiles within the same order of magnitude and similar vertical structure for the PM2. 5 particles. The mean centers of mass values are also close, with a mean bias of 0.57 km. On the opposite side, there are larger differences for the PM2. 5−10 mode, both in the boundary layer and in the free troposphere. In order to grasp the reasons behind the discrepancies, we investigate the effect of aerosol sources that are not properly included in the model's emission inventory and in the boundary conditions such as the wildfires and the desert dust component. The identification of the cases that are affected by wildfires is performed using wind backward trajectories from the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model in conjunction with satellite fire pixel data from MODerate-resolution Imaging Spectroradiometer (MODIS) Terra and Aqua global monthly fire location product MCD14ML. By removing those cases the correlation coefficient improves from 0.69 to 0.87 for the PM2. 5 integrated mass in the boundary layer and from 0.72 to 0.89 in the free troposphere. The PM2.5 center of mass fractional bias also decreases to 0.38 km. Concerning the analysis of the desert dust component, the simulations from the Dust Regional Atmospheric Model (BSC-DREAM8b) were deployed. When only the Saharan dust cases are taken into account, BSC-DREAM8b generally outperforms CAMx when compared with LIRIC, achieving a correlation of 0.91 and a mean bias of −29.1 % for the integrated mass in the free troposphere and a correlation of 0.57 for the center of mass. CAMx, on the other hand, underestimates the integrated mass in the free troposphere. Consequently, the accuracy of CAMx is limited concerning the transported Saharan dust cases. We conclude that the performance of CAMx appears to be best for the PM2.5 particles, both in the boundary layer and in the free troposphere. Sources of particles not properly taken into account by the model are confirmed to negatively affect its performance, especially for the PM2. 5−10 particles.

Validation of LIRIC aerosol concentration retrievals using airborne measurements during a biomass burning episode over Athens

In this paper we validate the Lidar-Radiometer Inversion Code (LIRIC) retrievals of the aerosol concentration in the fine mode, using the airborne aerosol chemical composition dataset obtained over the Greater Athens Area (GAA) in Greece, during the ACEMED campaign. The study focuses on the 2nd of September 2011, when a long-range transported smoke layer was observed in the free troposphere over Greece, in the height range from 2 to 3km. CIMEL sun-photometric measurements revealed high AOD (~0.4 at 532nm) and Ångström exponent values (~ 1.7 at 440/870nm), in agreement with coincident ground-based lidar observations. Airborne chemical composition measurements performed over the GAA, revealed increased CO volume concentration (~ 110ppbv), with 57% sulphate dominance in the PM1 fraction. For this case, we compare LIRIC retrievals of the aerosol concentration in the fine mode with the airborne Aerosol Mass Spectrometer (AMS) and Passive Cavity Aerosol Spectrometer Probe (PCASP) measurements. Our analysis shows that the remote sensing retrievals are in a good agreement with the measured airborne in-situ data from 2 to 4km. The discrepancies observed between LIRIC and airborne measurements at the lower troposphere (below 2km), could be explained by the spatial and temporal variability of the aerosol load within the area where the airborne data were averaged along with the different time windows of the retrievals.

Comparison of aerosol properties retrieved using GARRLiC, LIRIC, and Raman algorithms applied to multi-wavelength lidar and sun/sky-photometer data

Abstract. Aerosol particles are important and highly variable components of the terrestrial atmosphere, and they affect both air quality and climate. In order to evaluate their multiple impacts, the most important requirement is to precisely measure their characteristics. Remote sensing technologies such as lidar (light detection and ranging) and sun/sky photometers are powerful tools for determining aerosol optical and microphysical properties. In our work, we applied several methods to joint or separate lidar and sun/sky-photometer data to retrieve aerosol properties. The Raman technique and inversion with regularization use only lidar data. The LIRIC (LIdar-Radiometer Inversion Code) and recently developed GARRLiC (Generalized Aerosol Retrieval from Radiometer and Lidar Combined data) inversion methods use joint lidar and sun/sky-photometer data. This paper presents a comparison and discussion of aerosol optical properties (extinction coefficient profiles and lidar ratios) and microphysical properties (volume concentrations, complex refractive index values, and effective radius values) retrieved using the aforementioned methods. The comparison showed inconsistencies in the retrieved lidar ratios. However, other aerosol properties were found to be generally in close agreement with the AERONET (AErosol RObotic NETwork) products. In future studies, more cases should be analysed in order to clearly define the peculiarities in our results.

Profiling of aerosol microphysical properties at several EARLINET/AERONET sites during the July 2012 ChArMEx/EMEP campaign

Abstract. The simultaneous analysis of aerosol microphysical properties profiles at different European stations is made in the framework of the ChArMEx/EMEP 2012 field campaign (9–11 July 2012). During and in support of this campaign, five lidar ground-based stations (Athens, Barcelona, Bucharest, Évora, and Granada) performed 72 h of continuous lidar measurements and collocated and coincident sun-photometer measurements. Therefore it was possible to retrieve volume concentration profiles with the Lidar Radiometer Inversion Code (LIRIC). Results indicated the presence of a mineral dust plume affecting the western Mediterranean region (mainly the Granada station), whereas a different aerosol plume was observed over the Balkans area. LIRIC profiles showed a predominance of coarse spheroid particles above Granada, as expected for mineral dust, and an aerosol plume composed mainly of fine and coarse spherical particles above Athens and Bucharest. Due to the exceptional characteristics of the ChArMEx database, the analysis of the microphysical properties profiles' temporal evolution was also possible. An in-depth analysis was performed mainly at the Granada station because of the availability of continuous lidar measurements and frequent AERONET inversion retrievals. The analysis at Granada was of special interest since the station was affected by mineral dust during the complete analyzed period. LIRIC was found to be a very useful tool for performing continuous monitoring of mineral dust, allowing for the analysis of the dynamics of the dust event in the vertical and temporal coordinates. Results obtained here illustrate the importance of having collocated and simultaneous advanced lidar and sun-photometer measurements in order to characterize the aerosol microphysical properties in both the vertical and temporal coordinates at a regional scale. In addition, this study revealed that the use of the depolarization information as input in LIRIC in the stations of Bucharest, Évora, and Granada was crucial for the characterization of the aerosol types and their distribution in the vertical column, whereas in stations lacking depolarization lidar channels, ancillary information was needed. Results obtained were also used for the validation of different mineral dust models. In general, the models better forecast the vertical distribution of the mineral dust than the column-integrated mass concentration, which was underestimated in most of the cases.

Lidar-Radiometer Inversion Code (LIRIC) for the retrieval of vertical aerosol properties from combined lidar/radiometer data: development and distribution in EARLINET

Abstract. This paper presents a detailed description of LIRIC (LIdar-Radiometer Inversion Code) algorithm for simultaneous processing of coincident lidar and radiometric (sun photometric) observations for the retrieval of the aerosol concentration vertical profiles. As the lidar/radiometric input data we use measurements from European Aerosol Research Lidar Network (EARLINET) lidars and collocated sun-photometers of Aerosol Robotic Network (AERONET). The LIRIC data processing provides sequential inversion of the combined lidar and radiometric data. The algorithm starts with the estimations of column-integrated aerosol parameters from radiometric measurements followed by the retrieval of height dependent concentrations of fine and coarse aerosols from lidar signals using integrated column characteristics of aerosol layer as a priori constraints. The use of polarized lidar observations allows us to discriminate between spherical and non-spherical particles of the coarse aerosol mode.The LIRIC software package was implemented and tested at a number of EARLINET stations. Intercomparison of the LIRIC-based aerosol retrievals was performed for the observations by seven EARLINET lidars in Leipzig, Germany on 25 May 2009. We found close agreement between the aerosol parameters derived from different lidars that supports high robustness of the LIRIC algorithm. The sensitivity of the retrieval results to the possible reduction of the available observation data is also discussed.

A comparative study of aerosol microphysical properties retrieved from ground-based remote sensing and aircraft in situ measurements during a Saharan dust event

Abstract. In this work we present an analysis of aerosol microphysical properties during a mineral dust event taking advantage of the combination of different state-of-the-art retrieval techniques applied to active and passive remote sensing measurements and the evaluation of some of those techniques using independent data acquired from in situ aircraft measurements. Data were collected in a field campaign performed during a mineral dust outbreak at the Granada, Spain, experimental site (37.16° N, 3.61° W, 680 m a.s.l.) on 27 June 2011. Column-integrated properties are provided by sun- and star-photometry, which allows for a continuous evaluation of the mineral dust optical properties during both day and nighttime. Both the linear estimation and AERONET (Aerosol Robotic Network) inversion algorithms are applied for the retrieval of the column-integrated microphysical particle properties. In addition, vertically resolved microphysical properties are obtained from a multi-wavelength Raman lidar system included in EARLINET (European Aerosol Research Lidar Network), by using both LIRIC (Lidar Radiometer Inversion Code) algorithm during daytime and an algorithm applied to the Raman measurements based on the regularization technique during nighttime. LIRIC retrievals reveal the presence of dust layers between 3 and 5 km a.s.l. with volume concentrations of the coarse spheroid mode up to 60 µm3 cm−3. The combined use of the regularization and LIRIC methods reveals the night-to-day evolution of the vertical structure of the mineral dust microphysical properties and offers complementary information to that from column-integrated variables retrieved from passive remote sensing. Additionally, lidar depolarization profiles and LIRIC retrieved volume concentration are compared with aircraft in situ measurements. This study presents for the first time a comparison of the total volume concentration retrieved with LIRIC with independent in situ measurements, obtaining agreement within the estimated uncertainties for both methods and quite good agreement for the vertical distribution of the aerosol layers. Regarding the depolarization, the first published data set of the CAS-POL for polarization ratios is presented here and qualitatively compared with the lidar technique.

The Potential of The Synergy of Sunphotometer and Lidar Data to Validate Vertical Profiles of The Aerosol Mass Concentration Estimated by An Air Quality Model

Vertical profiles of the aerosol mass concentration derived by the Lidar/Radiometer Inversion Code (LIRIC), that uses combined sunphotometer and lidar data, were used in order to validate the aerosol mass concentration profiles estimated by the air quality model CAMx. Lidar and CIMEL measurements performed at the Laboratory of Atmospheric Physics of the Aristotle University of Thessaloniki, Greece (40.5N, 22.9E) from the period 2013-2014 were used in this study.

Methodologies to obtain aerosol property profiles from three-wavelength elastic lidar signals

The Lidar/Radiometer Inversion Code (LIRIC) and the Constrained Iterative Inversion (CII) procedure combined with a graphical aerosol classification framework (GF) have been used to analyse their ability in characterizing the altitude dependence of aerosol properties and evaluate their benefits and weaknesses. LIRIC and the CII technique rely on elastic lidar signals at 355, 532, and 1064 nm and collocated Aerosol Robotic Network (AERONET) Sun/sky photometer measurements to retrieve aerosol parameter profiles at the lidar wavelengths. The aerosol GF relies on the combined analysis of the Ångström exponent at the wavelength pairs 355 and 1064 nm (A(355, 1064)) and its spectral curvature (ΔA = A(355, 532) – A(532, 1064)) to estimate the fine-modal radius and the 532 nm fine-mode fraction. The application of the LIRIC and CII-GF techniques to three selected case studies representative of Central Mediterranean aerosol scenarios has revealed that the differences between the aerosol products from LIRIC and the corresponding ones from the CII-GF procedure varied with altitude, increased with the lidar wavelength decrease, and were significantly large when aerosol from different sources and/or from different advection routes was located at the altitudes sounded by the lidar. The plot on the aerosol GF of A(355, 1064) versus the spectral curvature has indicated that the LIRIC constraint that the fine-modal radius is height independent may represent a weakness if aerosol types and hence aerosol size distributions vary with altitude. The use of lidar ratios (LRs) constant with altitude could represent one of the main weaknesses of the CII-GF technique. The combined use of both techniques should allow obtaining a better characterization of the altitude dependence of aerosol properties from three-wavelength elastic lidar signals.

A methodology for investigating dust model performance using synergistic EARLINET/AERONET dust concentration retrievals

Abstract. Systematic measurements of dust concentration profiles at a continental scale were recently made possible by the development of synergistic retrieval algorithms using combined lidar and sun photometer data and the establishment of robust remote-sensing networks in the framework of Aerosols, Clouds, and Trace gases Research InfraStructure Network (ACTRIS)/European Aerosol Research Lidar Network (EARLINET). We present a methodology for using these capabilities as a tool for examining the performance of dust transport models. The methodology includes considerations for the selection of a suitable data set and appropriate metrics for the exploration of the results. The approach is demonstrated for four regional dust transport models (BSC-DREAM8b v2, NMMB/BSC-DUST, DREAMABOL, DREAM8-NMME-MACC) using dust observations performed at 10 ACTRIS/EARLINET stations. The observations, which include coincident multi-wavelength lidar and sun photometer measurements, were processed with the Lidar-Radiometer Inversion Code (LIRIC) to retrieve aerosol concentration profiles. The methodology proposed here shows advantages when compared to traditional evaluation techniques that utilize separately the available measurements such as separating the contribution of dust from other aerosol types on the lidar profiles and avoiding model assumptions related to the conversion of concentration fields to aerosol extinction values. When compared to LIRIC retrievals, the simulated dust vertical structures were found to be in good agreement for all models with correlation values between 0.5 and 0.7 in the 1–6 km range, where most dust is typically observed. The absolute dust concentration was typically underestimated with mean bias values of -40 to -20 μg m−3 at 2 km, the altitude of maximum mean concentration. The reported differences among the models found in this comparison indicate the benefit of the systematic use of the proposed approach in future dust model evaluation studies.

Hygroscopic growth of atmospheric aerosol particles based on active remote sensing and radiosounding measurements: selected cases in southeastern Spain

Abstract. A new methodology based on combining active and passive remote sensing and simultaneous and collocated radiosounding data to study the aerosol hygroscopic growth effects on the particle optical and microphysical properties is presented. The identification of hygroscopic growth situations combines the analysis of multispectral aerosol particle backscatter coefficient and particle linear depolarization ratio with thermodynamic profiling of the atmospheric column. We analyzed the hygroscopic growth effects on aerosol properties, namely the aerosol particle backscatter coefficient and the volume concentration profiles, using data gathered at Granada EARLINET station. Two study cases, corresponding to different aerosol loads and different aerosol types, are used for illustrating the potential of this methodology. Values of the aerosol particle backscatter coefficient enhancement factors range from 2.1 ± 0.8 to 3.9 ± 1.5, in the ranges of relative humidity 60–90 and 40–83%, being similar to those previously reported in the literature. Differences in the enhancement factor are directly linked to the composition of the atmospheric aerosol. The largest value of the aerosol particle backscatter coefficient enhancement factor corresponds to the presence of sulphate and marine particles that are more affected by hygroscopic growth. On the contrary, the lowest value of the enhancement factor corresponds to an aerosol mixture containing sulphates and slight traces of mineral dust. The Hänel parameterization is applied to these case studies, obtaining results within the range of values reported in previous studies, with values of the γ exponent of 0.56 ± 0.01 (for anthropogenic particles slightly influenced by mineral dust) and 1.07 ± 0.01 (for the situation dominated by anthropogenic particles), showing the convenience of this remote sensing approach for the study of hygroscopic effects of the atmospheric aerosol under ambient unperturbed conditions. For the first time, the retrieval of the volume concentration profiles for these cases using the Lidar Radiometer Inversion Code (LIRIC) allows us to analyze the aerosol hygroscopic growth effects on aerosol volume concentration, observing a stronger increase of the fine mode volume concentration with increasing relative humidity.

Optical, size and mass properties of mixed type aerosols in Greece and Romania as observed by synergy of lidar and sunphotometers in combination with model simulations: A case study

A coordinated experimental campaign aiming to study the aerosol optical, size and mass properties was organized in September 2012, in selected sites in Greece and Romania. It was based on the synergy of lidar and sunphotometers. In this paper we focus on a specific campaign period (23–24 September), where mixed type aerosols (Saharan dust, biomass burning and continental) were confined from the Planetary Boundary Layer (PBL) up to 4–4.5km height. Hourly mean linear depolarization and lidar ratio values were measured inside the dust layers, ranging from 13 to 29 and from 44 to 65sr, respectively, depending on their mixing status and the corresponding air mass pathways over Greece and Romania. During this event the columnar Aerosol Optical Depth (AOD) values ranged from 0.13 to 0.26 at 532nm. The Lidar/Radiometer Inversion Code (LIRIC) and the Polarization Lidar Photometer Networking (POLIPHON) codes were used and inter-compared with regards to the retrieved aerosol (fine and coarse spherical/spheroid) mass concentrations, showing that LIRIC generally overestimates the aerosol mass concentrations, in the case of spherical particles. For non-spherical particles the difference in the retrieved mass concentration profiles from these two codes remained smaller than ±20%. POLIPHON retrievals showed that the non-spherical particles reached concentrations of the order of 100–140μg/m3 over Romania compared to 50–75μg/m3 over Greece. Finally, the Dust Regional Atmospheric Model (DREAM) model was used to simulate the dust concentrations over the South-Eastern Europe.

Aerosol optical and microphysical properties observed by the lidar technique from a forest-fire smoke event over Madrid

On 27 August 2012, a wildfire occurred in the western zone of the Madrid region. Consequently, a significant release of smoke and aerosols was injected into the free troposphere and advected by the synoptic circulation in trajectories that passed over the capital. This event was detected by the Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas (CIEMAT; Research Centre for Energy, Environment and Technology), Madrid lidar station at about 5 km height. While the main aerosol plume did not pass over the lidar station, the eastern portion of the dispersed emissions did. No aerosol layers were detected by lidar in the free-troposphere for the next few days. Since few observations of fresh biomass burning aerosol have been carried out by lidar so far, this study contributes to previous studies on biomass burning aerosols, in particular regarding the first stages of the smoke transport.This article studies the optical and microphysical properties of the smoke aerosols retrieved by the lidar technique along with the recently developed Lidar/Radiometer Inversion Code (LiRIC), which combines both lidar and sun–sky photometer data. The sun–sky photometer data are provided by the Agencia Estatal de Meteorología (AEMET; Spanish Meteorological Agency) station close to the CIEMAT site. We suggest that the aerosol properties retrieved might be linked to the water uptake phenomenon in view of the fact that simultaneous water vapour lidar measurements exhibited a close relationship with backscatter coefficient profiles. This article is concerned not only with showing the capability of combining different remote-sensing techniques and the LiRIC code to provide aerosol vertical distribution for fine and coarse modes, but also with providing signs about the plausible interaction between aerosols and humidity that leads fresh biomass burning aerosols to act as cloud condensation nuclei. This key role, known as the indirect effect, remains the major source of uncertainty when the global radiation budget is assessed.

Assessment of aerosol's mass concentrations from measured linear particle depolarization ratio (vertically resolved) and simulations

Abstract. Multi-wavelength depolarization Raman lidar measurements from Magurele, Romania are used in this study along with simulated mass-extinction efficiencies to calculate the mass concentration profiles of different atmospheric components, due to their different depolarization contribution to the 532 nm backscatter coefficient. Linear particle depolarization ratio (δpart) was computed using the relative amplification factor and the system-dependent molecular depolarization. The low depolarizing component was considered as urban/smoke, with a mean δpart of 3%, while for the high depolarizing component (mineral dust) a mean δpart of 35% was assumed. For this study 11 months of lidar measurements were analysed. Two study cases are presented in details: one for a typical Saharan dust aerosol intrusion, 10 June 2012 and one for 12 July 2012 when a lofted layer consisting of biomass burning smoke extended from 3 to 4.5 km height. Optical Properties of Aerosols and Clouds software package (OPAC) classification and conversion factors were used to calculate mass concentrations. We found that calibrated depolarization measurements are critical in distinguishing between smoke-reach aerosol during the winter and dust-reach aerosol during the summer, as well as between elevated aerosol layers having different origins. Good agreement was found between lidar retrievals and DREAM- Dust REgional Atmospheric Model forecasts in cases of Saharan dust. Our method was also compared against LIRIC (The Lidar/Radiometer Inversion Code) and very small differences were observed.

Application of a Synergetic Lidar and Sunphotometer Algorithm for the Characterization of a Dust Event Over Athens, Greece

We present first retrievals of the Lidar-Radiometer Inversion Code (LIRIC), applied on combined lidar and sunphotometer data during a Saharan dust episode over Athens, Greece, on July 20, 2011. A full lidar dataset in terms of backscatter signals at 355, 532 and 1064 nm, as well as depolarization at 532 nm was acquired from the European Aerosol Research Network (EARLINET) station of Athens and combined with Aerosol Robotic Network (AERONET) data, in order to retrieve the concentration and extinction coefficient profiles of dust. The lidar measurements showed a free tropospheric layer between 1-5 km above Athens, with low Angstrom exponent of ~0.5 and high particle depolarization ratio, ~25-30%, both values characteristic of dust particles. The application of LIRIC revealed high concentration profiles of non-spherical coarse particles in the layer, in the range of 0.04-0.07 ppb and a smaller fine particle component with concentrations of ~0.01 ppb. The extinction coefficients at 532 nm ranged between 50 and 90 Mm-1 for coarse non-spherical particles and between 25 and 50Mm-1 for fine particles. The retrievals were compared with modeled dust concentration and extinction coefficient profiles from the Dust Regional Atmospheric Modeling (BSC-DREAM8b), showing good agreement, especially for the coarse mode

Application of a synergetic lidar and sunphotometer algorithm for the characterization of a dust event over Athens, Greece

We present first retrievals of the Lidar-Radiometer Inversion Code (LIRIC), applied on combined lidar and sunphotometer data during a Saharan dust episode over Athens, Greece, on July 20, 2011. A full lidar dataset in terms of backscatter signals at 355, 532 and 1064 nm, as well as depolarization at 532 nm was acquired from the European Aerosol Research Network (EARLINET) station of Athens and combined with Aerosol Robotic Network (AERONET) data, in order to retrieve the concentration and extinction coefficient profiles of dust. The lidar measurements showed a free tropospheric layer between 1-5 km above Athens, with low Angstrom exponent of ~0.5 and high particle depolarization ratio, ~25-30%, both values characteristic of dust particles. The application of LIRIC revealed high concentration profiles of non-spherical coarse particles in the layer, in the range of 0.04-0.07 ppb and a smaller fine particle component with concentrations of ~0.01 ppb. The extinction coefficients at 532 nm ranged between 50 and 90 Mm-1 for coarse non-spherical particles and between 25 and 50Mm-1 for fine particles. The retrievals were compared with modeled dust concentration and extinction coefficient profiles from the Dust Regional Atmospheric Modeling (BSC-DREAM8b), showing good agreement, especially for the coarse mode

Optical, microphysical, mass and geometrical properties of aged volcanic particles observed over Athens, Greece, during the Eyjafjallajökull eruption in April 2010 through synergy of Raman lidar and sunphotometer measurements

Abstract. Vertical profiles of the optical (extinction and backscatter coefficients, lidar ratio and Ångström exponent), microphysical (mean effective radius, mean refractive index, mean number concentration) and geometrical properties as well as the mass concentration of volcanic particles from the Eyjafjallajökull eruption were retrieved at selected heights over Athens, Greece, using multi-wavelength Raman lidar measurements performed during the period 21–24 April 2010. Aerosol Robotic Network (AERONET) particulate columnar measurements along with inversion schemes were initialized together with lidar observations to deliver the aforementioned products. The well-known FLEXPART (FLEXible PARTicle dispersion model) model used for volcanic dispersion simulations is initiated as well in order to estimate the horizontal and vertical distribution of volcanic particles. Compared with the lidar measurements within the planetary boundary layer over Athens, FLEXPART proved to be a useful tool for determining the state of mixing of ash with other, locally emitted aerosol types. The major findings presented in our work concern the identification of volcanic particles layers in the form of filaments after 7-day transport from the volcanic source (approximately 4000 km away from our site) from the surface and up to 10 km according to the lidar measurements. Mean hourly averaged lidar signals indicated that the layer thickness of volcanic particles ranged between 1.5 and 2.2 km. The corresponding aerosol optical depth was found to vary from 0.01 to 0.18 at 355 nm and from 0.02 up to 0.17 at 532 nm. Furthermore, the corresponding lidar ratios (S) ranged between 60 and 80 sr at 355 nm and 44 and 88 sr at 532 nm. The mean effective radius of the volcanic particles estimated by applying inversion scheme to the lidar data found to vary within the range 0.13–0.38 μm and the refractive index ranged from 1.39+0.009i to 1.48+0.006i. This high variability is most probably attributed to the mixing of aged volcanic particles with other aerosol types of local origin. Finally, the LIRIC (LIdar/Radiometer Inversion Code) lidar/sunphotometric combined inversion algorithm has been applied in order to retrieve particle concentrations. These have been compared with FLEXPART simulations of the vertical distribution of ash showing good agreement concerning not only the geometrical properties of the volcanic particles layers but also the particles mass concentration.

Evaluation of the Lidar/Radiometer Inversion Code (LIRIC) to determine microphysical properties of volcanic and desert dust

Abstract. The Lidar/Radiometer Inversion Code (LIRIC) combines the multiwavelength lidar technique with sun/sky photometry and allows us to retrieve vertical profiles of particle optical and microphysical properties separately for fine-mode and coarse-mode particles. After a brief presentation of the theoretical background, we evaluate the potential of LIRIC to retrieve the optical and microphysical properties of irregularly shaped dust particles. The method is applied to two very different aerosol scenarios: a strong Saharan dust outbreak towards central Europe and an Eyjafjallajökull volcanic dust event. LIRIC profiles of particle mass concentrations for the coarse-mode as well as for the non-spherical particle fraction are compared with results for the non-spherical particle fraction as obtained with the polarization-lidar-based POLIPHON method. Similar comparisons for fine-mode and spherical particle fractions are presented also. Acceptable agreement between the different dust mass concentration profiles is obtained. LIRIC profiles of optical properties such as particle backscatter coefficient, lidar ratio, Ångström exponent, and particle depolarization ratio are compared with direct Raman lidar observations. Systematic deviations between the LIRIC retrieval products and the Raman lidar measurements of the desert dust lidar ratio, depolarization ratio, and spectral dependencies of particle backscatter and lidar ratio point to the applied spheroidal-particle model as main source for these uncertainties in the LIRIC results.