Electromagnetic Radiation Levels Research Articles

The problem of protecting a person from the effects of low-frequency electromagnetic fields in modern society. Possible ways to solve it

The paper considers the problem of the impact of low-frequency electromagnetic fields (EMF) generated by electric vehicles (EV) and household appliances on humans in modern society. The data on the effect of EMF on human health and regulatory documents establishing requirements for electromagnetic safety are presented. The method of electromagnetic shielding and materials for the implementation of this method are considered as a promising method for solving the problem. The levels of electromagnetic radiation from a number of EV and household electrical appliances have been experimentally measured. The efficiency of electromagnetic shielding of materials based on single-layer coatings of Ni80Fe20 alloys, multilayer film structures Ni80Fe20/Cu and amorphous metal alloys AMAG172 has been estimated using a computational method. It is shown that electromagnetic screens based on these materials significantly reduce the levels of exposure to EMF of EV and household electrical appliances on humans, which allows us to approach the hygienic standards recommended by doctors and meet the requirements of regulatory documents on remote control.

Electromagnetic radiation estimation at the ground plane near fifth‐generation base stations in China by using machine learning method

AbstractA novel method based on machine learning is proposed to estimate the electromagnetic radiation level at the ground plane near fifth‐generation (5G) base stations. The machine learning model was trained using data from various 5G base stations, enabling it to estimate the electric field intensity at any arbitrary radiation point when the base station provides service to different numbers of 5G terminals which are in different service modes. The inputs required for the model include the transmit power of the antenna, the antenna gain, the distance between the 5G base station and 5G terminals, terminal service modes, the number of 5G terminals and the environmental complexity around the 5G base station. Experimental results demonstrate the feasibility and effectiveness of the estimation method, with the mean absolute percentage error of the machine learning model being approximately 5.98%. This level of accuracy showcases the reliability of the approach. Moreover, the proposed method offers low costs when compared with on‐site measurements. The estimated results can be utilised to reduce test costs and provide valuable guidance for optimal site selection, thereby facilitating radio wave coverage or electromagnetic radiation regulation of 5G base stations.

A study on the ambient electromagnetic radiation level of 5G base stations in typical scenarios

AbstractKnowledge of the electromagnetic radiation characteristics of 5G base stations under different circumstances is useful for risk prevention, assessment, and management. This paper selects several typical scenes (Open spaces, building concentration areas, user and building intensive areas) for electromagnetic radiation monitoring, and analyzes the relationship between ambient radiated power density and base station background. The results show that the factors that have significant impacts on the environmental radiation power density of 5G base stations including transmission distance, base station distribution, user density, building reflection superposition and so on. The radiation energy decays rapidly with distance. When the density of the building distribution is too large, the superposition effect caused by the reflected wave is concentrated at the distance of 50-70 meters. When the user density decreases (the superposition effect of reflected waves decreases), the 5G monitoring value follows the direct wave attenuation law and decreases rapidly with the increase of distance. Points with higher measured radiation in the simple access condition also had higher measured radiation in the high-speed download condition. With the popularization of 5G mobile phones and the increase of user density, the resource utilization of a single user will decline to the normal operation state, and the radiation environmental impact will be further reduced.

Sensitivity of endogenous autofluorescence in HeLa cells to the application of external magnetic fields

Dramatically increased levels of electromagnetic radiation in the environment have raised concerns over the potential health hazards of electromagnetic fields. Various biological effects of magnetic fields have been proposed. Despite decades of intensive research, the molecular mechanisms procuring cellular responses remain largely unknown. The current literature is conflicting with regards to evidence that magnetic fields affect functionality directly at the cellular level. Therefore, a search for potential direct cellular effects of magnetic fields represents a cornerstone that may propose an explanation for potential health hazards associated with magnetic fields. It has been proposed that autofluorescence of HeLa cells is magnetic field sensitive, relying on single-cell imaging kinetic measurements. Here, we investigate the magnetic field sensitivity of an endogenous autofluorescence in HeLa cells. Under the experimental conditions used, magnetic field sensitivity of an endogenous autofluorescence was not observed in HeLa cells. We present a number of arguments indicating why this is the case in the analysis of magnetic field effects based on the imaging of cellular autofluorescence decay. Our work indicates that new methods are required to elucidate the effects of magnetic fields at the cellular level.

Hygienic Studies of Electromagnetic Fields in the Work Environment during Operation of Ground-Based Radio Navigation and Aircraft Landing

Introduction: The development of navigation support for flights takes place in an environment of constantly increasing intensity of aeronautics, stricter requirements for accuracy, volume, and reliability of navigation information, efficiency of its processing. Radio navigation aids are improving, thus necessitating assessment of the electromagnetic situation at the workplaces of the personnel servicing modern equipment. Objective: To study and assess electromagnetic fields in the work environment of personnel engaged in the maintenance and operation of modern means of radio navigation and aircraft landing. Materials and methods: The research was carried out at three civil aviation facilities (two airports and an airfield) in 2021–2022. We established the composition, technical characteristics of the equipment, its operating modes, and parameters of radio frequency signals and measured the levels of electromagnetic fields at workplaces using the P3–42 electromagnetic radiation level meter. Results: The personnel are exposed to multi-frequency modulated electromagnetic fields of varying intensity. During the operation of glide and course radio beacons, radio transmitting devices at the dispatchers’ workplaces, levels of energy flux density and electric field strength exceeding hygienic standards are not created. In the premises of the hardware remote and near drive beacons, during the operation of the drive automatic radio station, an excess of the hygienic standards for the intensity of the electric field of the medium-wave range established for an 8-hour working day was registered; in the territory, the radiation from the antennas did not exceed the maximum permissible levels. Conclusions: The professional activity of the personnel servicing modern means of radio navigation and aircraft landing is carried out in a complex electromagnetic environment. A specific feature of working conditions is the effect on the body of multi-frequency, modulated electromagnetic fields of varying intensity and duration of exposure. These characteristics of radio frequency signals are essential adverse parameters that affect the formation of body responses. When choosing devices measuring the levels of electromagnetic fields, it is necessary to take into account the modulation parameters of radio frequency signals.

Residential exposure to non-ionizing electromagnetic radiation from mobile base stations: a systematic review on biological effects assessment

The effects of non-ionizing electromagnetic radiation from cellular base station exposure on human health are discussed in this review. Because of technological development, electromagnetic emissions are present at high levels in human existence. Due to the health risks linked with exposure to electromagnetic radiation (EMR), its effects are known. The systematic review work was done to identify measured values of non-ionizing radiation (such as power density and electric and magnetic fields) emitted by phones and GSM base stations, along with any potential biological consequences connected with the measured values. In the literature, all measurements of power density, electric fields, and magnetic fields were made using various instruments over a variety of base station distances and times. The findings from the literature showed that the non-ionizing electromagnetic radiation's power density, electric field, and magnetic field varied with distance from the tower and were highest at the closest distances. The findings also demonstrate that, in some situations, home exposure levels to base station-emitted non-ionizing electromagnetic radiation are within the limit. In some instances, however, the situation varies, and persons living close to base stations experience health effects from high levels of non-ionizing electromagnetic field exposure. The biological effects of non-ionizing electromagnetic radiation exposure in homes are summarized in this article. Numerous studies to date have established the dangers of mobile phone base station radiation to people and wildlife. The negative biological effects of exposure to non-ionizing electromagnetic radiation were compiled from numerous articles. Residents who are exposed to higher levels of non-ionizing electromagnetic radiation at home are more likely to experience symptoms like fatigue, nausea, disturbed sleep, discomfort, headache, memory loss, skin problems, visual disturbances, hearing problems, dizziness, muscle pain, DNA damage, and infertility. Some mobile base stations are situated quite close to homes and commercial buildings, putting individuals at risk from the base stations' electromagnetic radiation. Depending on the infrastructure impediment, such as interior obstructions or buildings, the emf changed from location to location. As a result, cellular mobile towers shouldn't be placed closer than 200 meters from residential structures.

Radiothermal Emission of Nanoparticles with a Complex Shape as a Tool for the Quality Control of Pharmaceuticals Containing Biologically Active Nanoparticles.

It has recently been shown that the titer of the SARS-CoV-2 virus decreases in a cell culture when the cell suspension is irradiated with electromagnetic waves at a frequency of 95 GHz. We assumed that a frequency range in the gigahertz and sub-terahertz ranges was one of the key aspects in the "tuning" of flickering dipoles in the dispersion interaction process of the surfaces of supramolecular structures. To verify this assumption, the intrinsic thermal radio emission in the gigahertz range of the following nanoparticles was studied: virus-like particles (VLP) of SARS-CoV-2 and rotavirus A, monoclonal antibodies to various RBD epitopes of SARS-CoV-2, interferon-α, antibodies to interferon-γ, humic-fulvic acids, and silver proteinate. At 37 °C or when activated by light with λ = 412 nm, these particles all demonstrated an increased (by two orders of magnitude compared to the background) level of electromagnetic radiation in the microwave range. The thermal radio emission flux density specifically depended on the type of nanoparticles, their concentration, and the method of their activation. The thermal radio emission flux density was capable of reaching 20 μW/(m2 sr). The thermal radio emission significantly exceeded the background only for nanoparticles with a complex surface shape (nonconvex polyhedra), while the thermal radio emission from spherical nanoparticles (latex spheres, serum albumin, and micelles) did not differ from the background. The spectral range of the emission apparently exceeded the frequencies of the Ka band (above 30 GHz). It was assumed that the complex shape of the nanoparticles contributed to the formation of temporary dipoles which, at a distance of up to 100 nm and due to the formation of an ultrahigh strength field, led to the formation of plasma-like surface regions that acted as emitters in the millimeter range. Such a mechanism makes it possible to explain many phenomena of the biological activity of nanoparticles, including the antibacterial properties of surfaces.

Self-Powered Wearable Breath-Monitoring Sensor Enabled by Electromagnetic Harvesting Based on Nano-Structured Electrochemically Active Aluminum

Self-powered sensors are gaining a lot of attention in recent years due to their possible application in the Internet of Things, medical implants and wireless and wearable devices. Human breath detection has applications in diagnostics, medical therapy and metabolism monitoring. One possible approach for breath monitoring is detecting the humidity in exhaled air. Here, we present an extremely sensitive, self-powered sensor for breath humidity monitoring. As a power source, the sensor uses electromagnetic energy harvested from the environment. Even electromagnetic energy harvested from the human body is enough for the operation of this sensor. The signal obtained using the human body as a source was up to 100 mV with an estimated power of 1 nW. The relatively low amount of energy that could be harvested in this way was producing a signal that was modulated by an interdigitated capacitor made out of electrochemically activated aluminum. The signal obtained in this way was rectified by a set of Schottky diodes and measured by a voltmeter. The sensor was capable of following a variety of different respiration patterns during normal breathing, exercise and rest, at the same time powered only by electromagnetic energy harvested from the human body. Everything happened in the normal environment used for everyday work and life, without any additional sources, and at a safe level of electromagnetic radiation.

Occupational health and safety: measurement and analysis of the electromagnetic radiation produced by radiofrequency devices for rejuvenation.

With the ongoing development of cosmetic technology, many different types of radiofrequency (RF) devices are widely used for face and body rejuvenation. These, like many other high-power devices, may emit excessive electromagnetic radiation into the surrounding environment. Long-term exposure to this environment can lead to poor health outcomes; therefore, it is important to measure and analyze the electromagnetic radiation levels for the health and safety of therapists. A handheld electronic electromagnetic radiation measuring instrument was used to measure the electric and magnetic field strengths. All results were analyzed using the R software (R Core Team, 2021-02-15). We found that the monopolar and unipolar RF devices that we measured from, in this study, could produce large amounts of electromagnetic radiofrequency emissions during operation, whereas the microneedle RF (bipolar RF) device emitted relatively lower amounts (P < 0.01). The strength of electromagnetic radiation is related to power and distance; it increases with power and decreases with distance. This study proved that certain RF devices for rejuvenation could cause severe electromagnetic radiofrequency pollution. The occupational health and safety of therapists require more attention, and effective protective measures need to be taken immediately.

CONCEPTUAL MODELING OF THE DATABASE OF GIS MONITORING OF ELECTROMAGNETIC POLLUTION OF SETTLEMENTS

The article presents the results of conceptual modeling of the geospatial database for monitoring electromagnetic pollution of settlements. Recently, the world has seen a rapid increase in the number of sources and the level of electromagnetic radiation. This can negatively affect people's health and their environment. The analysis of the publications showed that today researchers have formed a theoretical base for assessing the impact of electromagnetic radiation on people and the environment, developed models of the propagation of electromagnetic waves, ways and methods of protection against their harmful effects. However, not enough attention has been paid to monitoring the electromagnetic pollution of settlements. Systematic measurements of electromagnetic field levels are carried out only by individual EU countries Systematic control of this type of pollution is not carried out in Ukraine, there are no regulatory documents regarding the procedure for its monitoring, but the maximum permissible levels of electromagnetic fields for the population are established. Data on the distribution of electromagnetic fields are interdisciplinary in nature and necessarily contain an indication of the location of objects. For their effective processing, it is advisable to use geo-information technologies. Based on the results of the analysis of the subject area of electromagnetic pollution monitoring, a conceptual data model was developed. It is described using UML tools. The model contains two sets of data. The basic set of geospatial data includes information about buildings of various purposes, land plots, streets, highways, railways, engineering communications, relief, soils, hydrography, territory zoning, facility addresses. The profile set includes data on electromagnetic radiation sources and their sanitary protection zones, control points, the results of calculations and measurements of radiation parameters, the relative level of electromagnetic fields and the building restriction zones. The proposed model can be the basis of the physical modeling of the settlement's electromagnetic pollution monitoring system. &#x0D;

Substantiation of the Possibility to Use the Electromagnetic Shields Based on Powdered Aluminum Oxides to Reduce the Electromagnetic Radiation Energy of Electronic Devices

The article introduces the results of the experimental substantiation of the possibility to use the electromagnetic shields based on powdered aluminum oxides to reduce the electromagnetic radiation energy introduced by electronic devices. To achieve this goal, a methodology has been developed for assessing the effect of materials on the electromagnetic radiation level of electronic devices, and a methodology for estimating the radius of the controlled zone of the secondary electromagnetic radiation of computer equipment has been systematized. In accordance with the indicated methods, the study has been carried out, based on the results of which it was determined that electromagnetic shields containing the composite coating based on powdered aluminum oxides and iron oxide provide suppression of the electromagnetic radiation energy of electronic devices, as well as a reduction of up to 2 times the radius of the controlled zone of the secondary electromagnetic radiation of computer equipment. Recommendations for the practical application of the composite coatings based on the powdered alumina and iron oxide have been developed. In accordance with these recommendations, such coatings can be used in the process of manufacturing or improving the technical and functional properties of electromagnetic shields designed to ensure the electromagnetic compatibility of electronic devices, as well as to solve problems related to the information security.

Investigation of extremely low-frequency (1Hz-400kHz) pollution frequently encountered in social life: a case study of a shopping mall.

It is important to periodically measure, analyze, and map electromagnetic radiation levels due to potential risks. This study aims to draw attention to new electromagnetic pollution caused by radio frequencies and extremely low frequencies. For this reason, electric field and magnetic field measurements were carried out in the 1-Hz-400-kHz frequency band in a shopping mall, where electronic devices cause low-frequency electromagnetic radiation intensively. The measurements were performed with the EHP-50F device for 24h a day for a week. The measurements were made at 10 points in the shopping mall, and the measurement results were evaluated over five different sectors: electronics, clothing and accessories (male-female), personal care and cosmetics, supermarket, and the playland for children. Magnetic maps of each sector were produced. In addition, the specific absorption rates (SAR) of male and female customers in these workplaces were determined. This is the first study carried out to find SAR caused by low-frequency radiation. Although the safe limit value of SAR for the whole body is 0.08W/kg, the SAR values calculated in the playland and electronics sectors were obtained to be 0.763 and 0.39W/kg, respectively. Results clearly demonstrate how especially small children are exposed to danger in the long term.

Physical Differences between Man-Made and Cosmic Microwave Electromagnetic Radiation and Their Exposure Limits, and Radiofrequencies as Generators of Biotoxic Free Radicals

The critical arguments for radiofrequency radiation exposure limits are currently based on the principle that radio frequencies (RF) and electromagnetic fields (EMFs) are non-ionising, and their exposure limits are even 100-fold lower than those emitted from the Sun in the whole RF-EMF spectrum. Nonetheless, this argument has been challenged by numerous experimental and theoretical studies on the diverse biological effects of RF-EMF at much lower power density (W/m2) levels than today’s exposing limits. On the other hand, less attention has been given to counterarguments based on the differences in the physics concepts underlying man-made versus natural electromagnetic radiation (EMR) and on the fact that man’s biology has been adapted to the natural EMR levels reaching Earth’s surface at single EMF wavelengths, which are the natural limits of man’s exposure to EMFs. The article highlights the main points of interaction of natural and man-made radiation with biomatter and reveals the physical theoretical background that explains the effects of man-made microwave radiation on biological matter. Moreover, the article extends its analysis on experimental quantum effects, establishing the “ionising-like” effects of man-made microwave radiation on biological matter.

Methodology and device for diagnostics of high-voltage insulators based on continuous recording of the spatial level of electromagnetic radiation of partial discharges

THE PURPOSE. Development of diagnostic methods for high-voltage insulators in operation based on continuous recording of electromagnetic radiation. Hardware and software implementation of the device based on this technique. Carrying out experimental researches. METHODS. Received signal strength indicator measuring method of electromagnetic signals and method of determining the attenuation of electromagnetic radiation in space were used. RESULTS. The article describes relevance of the topic, considers various physical methods for registering partial discharges (PD) and their localization. Studies of the average signal level of defective and non-defective high-voltage insulators on load operation (10-15 kV) were carried out using the laboratory stand. An experiment was carried out to determine the space attenuation of a local signal from the PD. CONCLUSION. A technique for diagnosing high-voltage insulators during operation has been developed. This technique is based on continuous monitoring of electromagnetic radiation from partial discharges. Method for diagnosing high-voltage insulators makes it possible to monitor the insulation condition remotely and continuously.

Development of a flexible antenna-wristband for wearable wrist-worn infocommunication devices of the LTE standard

The object of research is the process of radiation of electromagnetic waves from a flexible antenna-wristband. The subject of research is the wave parameters and directional properties of a flexible antenna-wristband. The existing problem is that it is necessary to ensure the electromagnetic compatibility of the radio frequency units of the wrist-worn infocommunication device. This problem is due to the fact that LTE/NB-IoT, Bluetooth/Wi-Fi, and GPS antennas must be placed inside the small-sized case of the infocommunication device. To solve this problem, let’s propose a simple and cheap version of a broadband flexible bracelet antenna for LTE networks, located outside the device case. As a basis for the development of a flexible antenna-wristband, the authors chose a patch antenna, which is the base of the theory of microstrip antennas. This is due to the fact that the theoretical material is well developed for the calculation and study of the patch antenna. Structurally, a patch antenna consists of an upper metal layer that emits electromagnetic waves, a solid dielectric base, and a lower metal layer that acts as a reflector. With the classical approach to constructing a patch antenna, the width and length of its upper layer are commensurate, and its lower metal layer has geometric dimensions much larger than the upper metal layer. In contrast to the classical design, the authors proposed a new shape of the patch antenna, in which the length of the upper layer of the radiation surface is much greater than its width (5–6 times), and the lower metal layer has dimensions slightly larger than the dimensions of the upper layer. The authors have developed a flexible antenna-wristband for the frequency range of 800–1300 MHz with a wave impedance of 50 ohms, 118.7×23 mm of the upper metal layer, and 124.7×25 mm of the lower metal layer. The length of the microstrip feed line of the antenna is 54.6 mm, its width is 2 mm, and the length of the insert is 51.6 mm. The flexible antenna-wristband is connected to the printed circuit board of the infocommunication device by soldering or using a mini-coaxial cable. The authors developed an experimental layout of a flexible antenna-wristband and studied its wave and directional properties. It has been established that in the frequency range 800–1300 MHz the voltage standing wave ratio coefficient of this antenna does not exceed 3.5. The flexible antenna-wristband has directional properties, which allows reducing the level of electromagnetic radiation in the direction of the human body.

Simulation of Electromagnetic Radiation Environmental Impact of 5G Application Base Station

Based on the understanding of the radiation impact of 5G application base station construction on the environment, this paper simulated the electromagnetic radiation level of the environment after 5G application base station construction by establishing three numerical models. The study found that the prediction model based on population and mobile phone traffic characteristics can be used to predict the radiation environment of the whole region on the premise that 5G communication has been widely used by people, and this model is also suitable for the prediction and simulation of 3G/4G radiation environment.

Development of methods and models to improve the noise immunity of wireless communication channels

It has been shown that existing methods and models for improving the noise immunity of communication channels are not capable of meeting requirements for the quality of information in mobile infocommunication systems. In addition, the compromised quality of information fails to protect it and provide the speed of information transmission and density of access channels. It has been proven that reducing the level of electromagnetic radiation is the main method of ensuring noise immunity in wireless mobile communication systems of infocommunication systems. Therefore, one way to ensure the stable interference-free operation is to reduce the level of the information signal at the receiver input to the noise level when the signal/noise ratio is equal to one. This paper reports the results of studying methods and models with correlation reception of ultra-wideband signals. It is proved that according to the level of potential noise immunity, the best indicators are shown by the model of encoding an ultra-wideband information signal by phase manipulation, followed by the coding model with opposite chips, and the code-time manipulation model. It is shown that with a large base of the signal B&gt;300 when the intensity of the received signals is below the level of interference, reliable transmission of information is carried out with a probability of error of less than 10-6. This proves that the use of ultra-wide signal technology allows for wireless hidden transmission of information with low radiation power and a low probability of error. Thus, at a speed of 12 Mb/s, it is possible to chain the transmission of information with a probability of error less than 10-6 if there is a large signal base used, B =500‒1000.

Повышение защищенности информации от утечки через побочные электромагнитные излучения

The purpose of the article: development of software-implemented ways to increase the security of information from leakage through spurious electromagnetic radiation of a DVI video system. Research method: search for brightness gradations of RGB primary colors that form similar levels of spurious electromagnetic radiation by enumeration of experimental data obtained from fragments of the reconstructed image. Results: the first part of the article provides a review and analysis of the literature on the features of the functioning of the video interface of the DVI standard. The main characteristics of the TMDS coding algorithm, which can affect the parameters of spurious electromagnetic radiation of the video interface of modern computer technology, are considered. The second part of the article presents an experimental setup for analyzing the relationship between the visual contrast of an image and changes in the intensity of electromagnetic spurious emissions from a DVI video system. On the basis of an experimental comparison of the intensity values of side electromagnetic radiation for different color shades specified by RGB combinations, the possibility of using such pairs of color tone combinations that, on the one hand, are acceptable for the perception of information by the operator, and, on the other hand, have practically indistinguishable levels of side effects, is shown. electromagnetic radiation. The third part of the article (this is for the existing one) presents a method developed by the authors to increase the security of information from leakage through spurious electromagnetic radiation of a DVI video system. The possibility of implementing the proposed method for reducing the information content of spurious electromagnetic radiation of a video system when displaying two-color images is shown.

Measurement and Simulation-Based Exposure Assessment at a Far-Field for a Multitechnology Cellular Site up to 5G NR

5G is expected to be the dominant technology for mobile networks in the coming years, but there is concern about the increase in the total electromagnetic field radiation levels due to the deployment of the 5G technology. This paper presents an exposure assessment of electromagnetic field radiation on humans from single base station of a mobile network serving in dense, urban, suburban, and rural area scenarios for single-site transmission with multi-technology, including 2G, 3G, 4G, IoT, and 5G which have recently been deployed. This assessment is performed using simulation to predict the received signal levels and to calculate the related power densities for a typical single site under operating field configurations and settings for each technology. Field measurements were performed using a drive test tool to validate and calibrate the simulation results. The results show the total exposure ratio was very low compared to the international standard exposure limits, and the results show the contribution from each technology for these spesfic sites used in this study.

Research Concerning Electromagnetic Emissions from Residential On-grid PV Systems

The paper presents the results of grid power quality tests and wide frequency electromagnetic radiation level tests to which home power networks with photovoltaic systems have been subjected. The said results are meaningful from the point of view of safety and compatibility of electrical devices and the power supply system they are connected to. The tests covered stability of phase voltage and its frequency, harmonic level flicker, as well as RF radiated and emission levels. The measurements performed provide an answer to the question concerning the level of compliance of randomly selected home-installed PV systems with applicable recommendations and regulations concerning electromagnetic compatibility. The ability to meet the applicable standards translates into the health and safety of building inhabitants, which is the ultimate goal. Legal regulations concerning electromagnetic compatibility of renewable energy sources are consistent throughout the entire European Union.