Contamination Levels Research Articles

Temporal and spatial trends of imidacloprid-related hazards in France

Neonicotinoids are the top-selling insecticides worldwide. Because of their method of use, mainly to coat seeds, neonicotinoids have been found to widely contaminate the environment. Their high toxicity has been shown to be a major concern in terms of impact on biodiversity, and the use of these insecticides has been associated with population declines of species in different countries. Despite the widespread recognition of the risk of neonicotinoids to biodiversity, their temporal and spatial use remains poorly known in many countries. Yet this information is essential to address the potential impacts of these pesticides on biodiversity and to inform measures to establish protected areas or biodiversity restoration. The present study relied a large publicly available dataset to characterise the temporal and spatial use in France of imidacloprid, the most widely used neonicotinoid worldwide, as well as analysed water contamination surveys between 2005 and 2022 to assess the contamination of the environment. The results show that imidacloprid was the main neonicotinoid used in France over the study period. This use was spatially structured, with higher use in northern and western France, particularly related to cereal and beet crops area. The water contamination survey indicated that imidacloprid has widely contaminated the environment and consequently increased the risk to biodiversity, especially in counties crossed by the Loire, Seine and Vilaine rivers. This risk increased between 2005 and 2018 due to the higher use of imidacloprid and decreased sharply after 2018 due to its ban, although it was reauthorized by derogation for sugar beet in 2021. This study is the first assessment of imidacloprid pressure on biodiversity in France and shows the spatial and temporal correlation between agricultural practices and the freshwater contamination level. These results will help to identify priority areas for mitigation and restoration measures.

Evidence of heavy metal in soil, irrigation water and vegetable cultivated in peri‑urban area of Yaoundé-Cameroon

Environmental pollution from anthropogenic activities is of global concern. The levels of heavy metal contamination were evaluated in the soil and irrigation water, and their transferability to the cultivated plant was appraised in the locality of Nkolbisson, Yaoundé-Cameroun. The levels of Zn, Cu, Cd, Ni, Pb, Cr, and Mn contamination were evaluated to determine the current status, possible source(s), bio-accumulation in food crops, the suitability of the water for irrigation purposes, and hence the probable health risk. The analysis of soils, waters, and crops (Corchorus olitorius and Lactuca sativa) samples has shown high levels of heavy metal contamination. Cd, Ni, and Cr concentrations in water samples (0.98, 2.230, and 2.635 mg/l) were above the threshold set by FAO for irrigation water. In agricultural soils, only the level of Mn (1013.090 mg/kg) contained in soil samples was above the European Union (EU) and the Canadian Council of Ministers for Environment (CCME) thresholds of toxicity. Except for Pb (0.361; 0.394 and 0.043; 0.041 mg/kg DM) and Mn (113.457; 123.341 and 173.667; 180.321 mg/kg DM), the concentration of heavy metals analysed in plant samples were above the standard values in the edible parts. Market gardening in this city presents risks due to the presence of heavy metals in soils and irrigation waters. Thus, market gardeners must be taking appropriate measures to avoid crop contamination. The bioconcentration and translocation factors have shown that Lactuca sativa can be used for phytoextraction of Zn, Cu and Cd whereas Corchorus olitorius can be used for phytomobilization of the same elements.

Detection of DNA Contamination in Prenatal Samples from Whole Exome Sequencing Data.

Maternal cell contamination (MCC) in prenatal samples poses a risk for misdiagnosis, and therefore, testing for contamination is necessary during genetic analysis of prenatal specimens. MCC testing is currently performed as a method separate from the diagnostic method. With the increasing application of whole exome sequencing (WES) in prenatal diagnosis, we sought to develop a method to estimate the level of contamination from WES data, aiming to eliminate the need for a separate MCC test. To investigate the impact of MCC on the distribution of the variant allele fraction in WES data, contamination was both simulated in silico and artificially induced. Subsequently, a bioinformatic WES contamination method was developed and validated by comparing its performance to that of the gold standard (short tandem repeat [STR]) MCC test, validated for detecting ≥5% contamination. Finally, post-implementation performance was monitored for a 15-month period. During validation, 270 prenatal samples underwent analysis with both WES and the gold standard test. In 259 samples, the results were concordant (248 not contaminated, 11 contaminated with both tests). In 11 samples, contamination was only detected in WES data (2 of which contained ≥5% contamination with WES, which is above the detection limit of the gold standard test). The data of the post-implementation evaluation on 361 samples, of which 68 were contaminated, were in line with the validation data. Contamination can reliably be detected in WES data, rendering a separate contamination test unnecessary for the majority of samples.

Contribution of Farm-level Hygiene and Handling Practices to Microbial Safety Profiles in the Informal Dairy Sector in Zimbabwe

The current study assessed (i) the microbiological safety level profiles (MSLPs) of milkmen’s hands and milking containers and (ii) the influence of hygiene and handling practices on MSLPs of raw and cultured milk, from six informal dairy farms in Zimbabwe. Interviews and direct observations were carried out during the assessment of hygiene and handling practices at six farms designated A to F. Microbiological criteria of the following six microbiological parameters: Total Bacterial Counts (TBCs), Coliform Counts (CCs), Total Escherichia coli Counts (TECs), Salmonella spp., Listeria monocytogenes and Klebsiella pneumonia, were used to determine contamination level (CL) at four different critical sampling locations (CSLs). The CSLs were raw milk (CSL1), cultured milk (CSL2), milkmen’s hands (CSL3), and milking containers (CSL4). The microbiological criteria of the six microbiological parameters were used to score CLs as: intolerable (0), poor to average (1), average (2), and good (3). MSLPs at each CSL for the six farms were computed based on the CL scores to a maximum score of 18. A total of 192 samples were collected and analyzed. Salmonella spp. and L. monocytogenes were not detected at all the CSLs. All the farms failed to achieve a maximum MSLP score of 18 at all the CSLs. The relationship between MSLPs and hygiene and handling practices was tested using point-biserial correlation coefficients. The correlation study revealed that handling and hygiene practices (such as the duration between milking and storage, the type of milking container utilized at farms, the frequency of cleaning the milking parlor, the water source for hand and equipment washing, and the use of hand sanitizers) generally influenced the MSLPs on the farms. Both training and improvement in infrastructure are needed to improve the quality of milk and its products produced and sold in the informal value chain in Zimbabwe.

Changepoint Analysis of Natural Attenuation in Groundwater Improves Forecasts of Time to Attain Goal

AbstractWhen a remedy is selected for groundwater contamination, the monitoring record is often evaluated to extract rate constants for attenuation of contaminants over time, and the rate constants are used to forecast a time when the concentrations will attain a clean‐up goal. These evaluations typically assume the rate constant does not change. Data from 11 monitoring wells at the former Twin Cities Army Ammunition Plant (TCAAP) were evaluated to test whether this assumption was valid for this site. A previous evaluation at this site (based on data from 1987 through 1999) extracted rate constants that would bring the concentrations of trichloroethylene (TCE) in the 11 wells to the maximum contaminant level (MCL) on or before 2013. By 2020, only four wells had reached the MCL. Piecewise linear regressions were used to model the relationship between time elapsed and concentration of TCE for each well, and to identify any changepoints in the rate of attenuation over time. Each well had at least one changepoint with different TCE attenuation rates on either side of the changepoints. The slope of the most recent segment after the last changepoint provides the best information to forecast concentrations in the future. For four of the wells, that forecast indicated that concentrations of TCE would never reach the MCL. Piecewise linear regression analysis proved to be a valuable tool to detect changes in rate constants, and to update forecasts of the time required for groundwater concentrations to reach a cleanup goal.

Fate and partition of perfluoroalkyl acids (PFAAs) driven by particles in mangrove ecosystems: Mechanistic insights and environmental implications

A critical gap in understanding emerging pollutants in mangrove ecosystems should be addressed. Despite their ecological importance, the state of environmental quality in fragmented mangrove patches, especially emerging contaminants, remains largely uncharted. Our research presented an in-depth analysis of the distribution of perfluoroalkyl acids (PFAAs) across porewater, suspended particles, and sediment in these small, fragmented mangroves, revealing the mechanisms behind their distribution. The findings indicated that PFAA concentrations in sediments were generally lower than in suspended particles, except for C12–C14 perfluorinated carboxylic acids (PFCAs) and C4–C6 perfluorinated sulfonic acids (PFSAs). A comparison of contamination levels in different mangrove patches concurred with conventional water quality assessments and crab burrow surveys, showing that large artificially planted patches were less contaminated, while areas with intense human activity were more polluted. Notably, no significant differences were observed in the concentrations of long-chain PFAAs and PFCAs between patches (p > 0.1). Elevated crab burrowing activity and higher concentrations of perfluorobutanoic acid (PFBA) and perfluorohexane sulfonic acid (PFHxS) in suspended particles in low intertidal zones suggested that seafood, particularly crabs and shellfish, might be at risk of PFAA pollution. Rainfall-runoff was identified as the primary source of PFAA pollution in porewater and suspended particle systems in these areas. The transport of PFAAs and organic carbon in mangroves was influenced by the concentrations and properties of suspended particles. These insights were critical for developing targeted environmental management strategies to mitigate the impact of PFAAs and preserve the ecological integrity of mangrove ecosystems.

Sweet corn phytoglycogen dendrimers as a lyoprotectant for dry‐state protein storage

AbstractProtein biotherapeutics typically require expensive cold‐chain storage to maintain their fold and function. Packaging proteins in the dry state via lyophilization can reduce these cold‐chain requirements. However, formulating proteins for lyophilization often requires extensive optimization of excipients that both maintain the protein folded state during freezing and drying (i.e., “cryoprotection” and “lyoprotection”), and form a cake to carry the dehydrated protein. Here we show that sweet corn phytoglycogens, which are glucose dendrimers, can act as both a protein lyoprotectant and a cake‐forming agent. Phytoglycogen (PG) dendrimers from 16 different maize sources (PG1‐16) were extracted via ethanol precipitation. PG size was generally consistent at ~70–100 nm for all variants, whereas the colloidal stability in water, protein contaminant level, and maximum density of cytocompatibility varied for PG1‐16. 10 mg/mL PG1, 2, 9, 13, 15, and 16 maintained the activity of various proteins, including green fluorescent protein, lysozyme, β‐galactosidase, and horseradish peroxidase, over a broad range of concentrations, through multiple rounds of lyophilization. PG13 was identified as the lead excipient candidate as it demonstrated narrow dispersity, colloidal stability in phosphate‐buffered saline, low protein contaminants, and cytocompatibility up to 10 mg/mL in NIH3T3 cell cultures. All dry protein‐PG13 mixtures had a cake‐like appearance and all frozen protein‐PG13 mixtures had a Tg' of ~ −26°C. The lyoprotection and cake‐forming properties of PG13 were density‐dependent, requiring a minimum density of 5 mg/mL for maximum activity. Collectively these data establish PG dendrimers as a new class of excipient to formulate proteins in the dry state.

Standardization and Quality Assessment of Drakshavaleha: Insights from Three Marketed Brands

Drakshavaleha, a traditional Ayurvedic formulation, is widely used for its therapeutic benefits in treating respiratory and digestive ailments. This study aims to standardize and evaluate the quality of Drakshavaleha from three different marketed brands through a comprehensive assessment of their physicochemical and pharmacognostical properties, alongside an estimation of toxic heavy metals content and microbial contamination, and phytochemical profiles. Materials and Methods: Three brands of Drakshavaleha were meticulously assessed through a range of tests, including organoleptic analysis, physicochemical evaluations, heavy metal content analysis, microbial contamination assessments, and qualitative phytochemical screenings. Standardized protocols and methodologies from pharmacopoeias were used for all evaluations to ensure reliable and consistent results. Results and Discussion: The findings indicated notable variations in the evaluation parameters of the different brands. Physicochemical and Pharmaceutical analysis revealed disparities in pH levels and total reducing sugar levels. Heavy metal testing and microbial contamination levels were within acceptable ranges for all samples. The qualitative phytochemical screening identified differences in the concentration of key active ingredients, potentially impacting therapeutic efficacy. Conclusion: This study underscores the importance of standardization in maintaining the safety and efficacy of Ayurvedic formulations. By identifying variations in quality and safety parameters, it provides critical insights for manufacturers to improve their production processes. Ultimately, this research advocates for enhanced quality assurance practices to uphold the integrity of Ayurvedic medicine in the global market.

Seasonal variation in heavy metal intake and excretion by dairy cattle in an Indian megacity

Milk consumption plays a pivotal role in human nutrition, especially for children, due to its high protein, calcium, and vitamin contents that aid cognitive development. Nonetheless, potential hazards from heavy metal presence in milk, due to environmental exposure and intake through feed, have gained global attention. Given paucity of data we investigated the seasonal variation in the quantitative intake of heavy metals (cadmium: Cd, chromium: Cr, lead: Pb) by dairy cows in the South Indian megacity of Bengaluru, and the resulting heavy metal concentrations in milk and feces. The research involved 39 dairy farms across urban and peri‑urban areas, where 281 feed, 329 milk, and 183 feces samples were collected along with management data during monsoon (July 2020 - August 2020), winter (November 2020 – February 2021) and summer (March 2022 – June 2022) seasons. During the summer season, Cd concentration in lake fodder averaged 1.6 mg/kg DM, which was higher than the 0.6 mg/kg DM during winter and 0.9 mg/kg DM during the monsoon season. The higher concentration resulted in an increased daily Cd intake of 13.7 mg/cow/day. Similarly, Cr and Pb intake were also highest in summer (Cr: 46.3 mg/cow/day, Pb: 11.7 mg/cow/day), whereby for both elements the concentrations were higher in non-lake feed than in lake fodder. With the exception of a few milk samples, Cr and Pb concentrations were below threshold levels and did not compromise milk safety, and Cd levels never raised concerns. Nevertheless, elevated Cr and Pb concentrations (Cr: 9.8–16.9 mg/kg DM, Pb: 4.1–10.6 mg/kg DM) were determined in feces across seasons, potentially endangering the environment and reintroducing these elements into the food chain through manure application on agricultural land. Rather than uniformly discouraging the use of lake fodder in Bengaluru, authorities on the one hand should caution fodder usage in pollution-prone areas, and on the other hand take measures to reduce contamination levels at those sites. Furthermore, it appears necessary to implement more stringent control measures for other types of feedstuffs. Raising farmers' awareness of the problem of heavy metals in the food chain could promote their compliance with regulations without the need for complete feed bans, which are difficult to enforce in a highly contested urban environment.

Shift in Bacterial Community Structure in the Biodegradation of Benzene and Toluene under Sulfate-Reducing Condition.

Groundwater contaminated by benzene and toluene is a common issue, posing a threat to the ecosystems and human health. The removal of benzene and toluene under sulfate-reducing condition is well known, but how the bacterial community shifts during this process remains unclear. This study aims to evaluate the shift in bacterial community structure during the biodegradation of benzene and toluene under sulfate-reducing condition. In this study, groundwater contaminated with benzene and toluene were collected from the field and used to construct three artificial samples: Control (benzene 50 mg/L, toluene 1.24 mg/L, sulfate 470 mg/L, and HgCl2 250 mg/L), S1 (benzene 50 mg/L, toluene 1.24 mg/L, sulfate 470 mg/L), and S2 (benzene 100 mg/L, toluene 2.5 mg/L, sulfate 940 mg/L). The contaminants (benzene and toluene), geochemical parameters (sulfate, ORP, and pH), and bacterial community structure in the artificial samples were monitored over time. By the end of this study (day 90), approximately 99% of benzene and 96% of toluene could be eliminated in both S1 and S2 artificial samples, while in the Control artificial sample the contaminant levels remained unchanged due to microbial inactivation. The richness of bacterial communities initially decreased but subsequently increased over time in both S1 and S2 artificial samples. Under sulfate-reducing condition, key players in benzene and toluene degradation were identified as Pseudomonas, Janthinobacterium, Novosphingobium, Staphylococcus, and Bradyrhizobium. The results could provide scientific basis for remediation and risk management strategies at the benzene and toluene contaminated sites.

Fabrication of PVDF membranes via γ-ray irradiation and investigation into their membrane formation mechanisms and water treatment properties

Polyvinylidene fluoride (PVDF) membrane is a cheap and commonly used separation material, but its inherent hydrophobicity results in significant membrane contamination, which limits its engineering application and further development. The hydrophilic PVDF-g/co-NVP membrane was prepared through low-dose γ-ray irradiation and using N-vinyl-2-pyrrolidinone (NVP) as a modifier in this study. The effects of γ-ray dose and incorporating NVP additive on the microstructure, hydrophilicity, anti-fouling capability, and mechanical capacity of membranes were discussed. Molecular dynamics (MD) simulation method was used to comprehensively investigate the impact of the NVP on the physicochemical characteristics of membrane structure. Under a specific NVP load, the water contact angle of the membrane decreases from 87.92° to 52.66°. The pure water permeance reaches 362.1 L/m2 h, and the porosity increases to 55.21 %±1.29 %, which indicates that γ-ray irradiation with NVP addition can effectively adjust the pore structure and hydrophilicity of the membrane. During anti-fouling test against bovine serum albumin (BSA), the modified membrane exhibits remarkable anti-fouling characteristics, including reduced BSA accumulation, enhanced flux recovery, lower irreversible contamination level, and extended cleaning cycle compared with the original pure PVDF membrane because of its higher hydrophilicity and positive zeta-potential value. This study elucidates the mechanism underlying γ-ray graft modification of PVDF membranes, thereby providing valuable insights into the development of efficient functional membrane materials.

Influence of paternal factors on plastic ingestion and brominated chemical exposure in East Tropical Atlantic Procellariid chicks

The presence of plastic debris and organo-brominated compounds in the marine environment poses a concern to wildlife. Plastic can absorb and release chemical compounds, making their ingestion potentially harmful, while chemical compounds have become omnipresent, with a tendency to bioaccumulate in the food web. Seabirds are often used as indicators of marine plastic pollution, yet studies on the exposure of tropical communities to plastic contamination are still scarce. In this study we monitored the amounts of plastics in faeces and organo-brominated compounds ingested/assimilated in feathers by adults and chicks of Cape Verde shearwaters and Bulwer's petrels from Cabo Verde. Anthropogenic pollutants, polybrominated diphenyl ethers (PBDEs), and naturally generated methoxylated-PBDEs (MeO-PBDEs) were among the probed compounds. The frequency of plastic debris ingestion was similar in both species' adults and chicks, although, the characteristics of the ingested plastic differed. Frequency and number of microplastics increased throughout the nestling season for chicks from both species. All species and age groups showed the presence of PBDEs and MeO-PBDEs. Among PBDEs, Bulwer's petrels exhibited higher concentrations than Cape Verde shearwaters, and chicks had higher concentration profiles than adults. Specifically, Bulwer's petrel chicks showed higher concentrations than Cape Verde shearwater chicks. On the contrary, Cape Verde shearwater adults exhibited higher occurrence and concentrations of MeO-PBDEs when compared to Cape Verde shearwater chicks. We found no effect of plastic loadings or loadings of organohalogen contaminants on body condition or size, although harmful effects may be hidden or reveal themselves in a medium- to long-term. Feather samples from both adults and chicks were shown to be useful for comparing intraspecific contamination levels and appear suitable for the long-term assessment of organohalogen contaminants in seabirds. Species-specific foraging and feeding strategies are likely the drivers of the observed variation in organochlorine contamination burdens among seabird species.

Exploring organophosphate ester contamination and distribution in food: A meta-analysis

This study examines the food safety risk of organophosphate esters (OPEs) by analyzing data from 23 studies with 14,915 data points. We found EDP contamination highest in cereals, dairy, and meats, and TEHP most prevalent in vegetables and fruits, with contamination levels reaching 4.54 ng/g and 1.46 ng/g, respectively. Food processing influences OPE contamination through complex and multifaceted, akin to a “double-edged sword.”, as meta-analysis and Principal Component Analysis (PCA) revealed. Estimated Dietary Intakes (EDI) identified vegetables and cereals as primary OPE sources, contributing 33.3% and 23.8% of total intake, with EDI values of 44.74 ng/kg bw/day and 32.25 ng/kg bw/day, respectively. Current exposure levels are within U.S. EPA safety thresholds (HQ < < 1), but the heightened risk to infants and children necessitates revising safety standards and ongoing monitoring.

A Comprehensive Review on Aflatoxin Contamination, Its Impact on Human Health and Management Strategies

Background: Aflatoxins are secondary metabolites produced by Aspergillus species, significantly impact global economic and health sectors, and contaminating key agricultural products such as maize, cotton, and groundnuts. The mycotoxins, particularly types B1 and B2, pose severe risks to animal and human health, leading to diseases like hepatic cellular carcinoma and liver cancer. Objective: This review aims to analyze the prevalent impacts of AF contamination on human health and to evaluate current management strategies to mitigate this issue. Methods: We utilize a comprehensive array of techniques to detect AF in agricultural products, including culturing, chromatography, immunochemical methods, and molecular assays. Our review also explores preventive measures during the pre-harvest and post-harvest phases of crop development, focusing on the efficacy of biopesticides in reducing contamination levels. Results: AF contamination levels vary widely, with some regions recording levels as high as 35 ppb in crops, surpassing the maximum residue limits (5-20 ppb) set by many countries. The application of biopesticides has shown a reduction in toxigenic strain prevalence by up to 40%, demonstrating a significant decrease in AF levels in treated crops compared to untreated ones. Conclusion: Effective management of AF contamination involves early detection and the strategic use of biopesticides to control fungal growth. Adopting these strategies can substantially reduce the health risks associated with AF exposure.

Sunscreen pollution is abated during the COVID-19 “Anthropause” of 2020 in two U.S. National Parks: Cape Lookout National Seashore and Kaloko-Honokōhau National Historical Park

From March to June 2020, governments across the world imposed lockdowns in an attempt to reduce the transmission of COVID-19 during the early phase of the pandemic. This period of time in which human activity slowed worldwide has been coined the “Anthropause”. The goal of this study was to determine if sunscreen pollution abated during the Anthropause and to identify the severity of the pollution when tourism/recreation recovered at two coastal units of the U.S. National Park System: Kaloko-Honokōhau National Historical Park in Hawaiʻi, U.S.A. and Cape Lookout National Seashore in North Carolina, U.S.A. Active ingredients of sunscreen products were measured in water and sand samples at both locations, including oxybenzone, octinoxate, octocrylene, octisalate, homosalate, and relevant breakdown products of some of these ingredients. A risk assessment was conducted on Anthropause and post-Anthropause contaminant levels for both locations to determine if there was a threat reduction during the Anthropause, and whether tourism recovery in the post-Anthropause period served as a threat to coastal wildlife. Both national park units exhibited an almost absolute reduction in the levels of sunscreen contamination during the Anthropause period, a striking commonality considering the geographic expanse separating the parks. Once travel restrictions were lifted, a large influx of tourists ensued at both locations, resulting in a relatively sudden and dangerous increase in the levels of sunscreen chemical pollution. This study supports the argument that unmanaged tourism is a source of coastal sunscreen pollution that poses a threat to the localized continuity of species populations and biodiversity, especially to coral reefs and fisheries.

Comprehensive index analysis approach for ecological and human health risk assessment of a tributary river in Bangladesh

This study examined the water quality of the Turag River, an important tributary river in Dhaka, Bangladesh in terms of physicochemical characteristics and heavy metal contamination to assess the potential risks to both ecological systems and human health. The majority of the water samples complied with the acceptable limits established by the World Health Organization (WHO) for various parameters including pH, electrical conductivity (EC), total dissolved solids (TDS), dissolved oxygen (DO), chemical oxygen demand (COD), sodium adsorption ratio (SAR), and magnesium adsorption ratio (MAR), except total hardness (TH). The sodium (Na), potassium (K), calcium (Ca), magnesium (Mg), chloride (Cl−), fluoride (F−), nitrate (NO3−), and sulfate (SO42−) levels in the water samples were found to be within acceptable ranges for most cases. Moreover, heavy metals including lead (Pb), cadmium (Cd), chromium (Cr), nickel (Ni), iron (Fe), manganese (Mn), zinc (Zn), copper (Cu), arsenic (As), selenium (Se), and mercury (Hg) were analyzed and their mean concentrations (μg/L) were found in the order of Fe (244.72 ± 214.35) > Mn (28.93 ± 29.64) > Zn (22.97 ± 10.93) > Cu (8.28 ± 5.99) > Hg (8.23 ± 6.58) > As (1.34 ± 0.39) > Ni (1.20 ± 0.38) > Cr (0.67 ± 0.85) > Pb (0.61 ± 0.72) > Se (0.42 ± 0.48) > Cd (0.13 ± 0.09) which were within the acceptable limit, except Hg. The cumulative effect of all heavy metals was assessed through the heavy metal pollution index (HPI), contamination degree (Cd), and nemerow pollution index (PN). The mean value of HPI (682.38 ± 525.68) crossed the critical index value of 100, indicating an elevated level of pollution. The mean value of Cd (8.763 ± 6.48) indicates a low-moderate-significant level of contamination due to an elevated level of Hg, and for the PN it was found 174.27 ± 146.66, indicating a high level of pollution due to high level of Fe. Ecological risk index (ERI) indicated low levels of risk for Pb, Cd, Cr, Ni, Fe, Mn, As, Se, Cu, and Zn but a significantly high risk for Hg. The water was classified as good to excellent based on its physicochemical properties (pH, EC, TDS, COD, DO, F−, Cl−, NO3−, and SO42−) while it was deemed poor to unsuitable for heavy metals according to the water quality index (WQI). Among the carcinogenic constituents, As poses the greatest carcinogenic risk, particularly for children. The mean value of Cr, Mn, and As in the HQingestion for adult and child, and Cd, Hg for child exceeded the threshold value established by the United States Environmental Protection Agency (USEPA), while the HQdermal values remained below the maximum limit for all heavy metals. The value of HI at all locations exceeds the threshold of 1, as specified by USEPA. Principal component analysis (PCA) and cluster analysis revealed that the presence of heavy metals in the Turag River was mainly attributed to anthropogenic sources, including industrial effluent discharge from neighboring industries, domestic wastewater, and agricultural runoff containing agrochemicals from the surrounding lands.

Once through continuous mode electrocoagulation for tannery wastewater remediation: Process optimization and performance evaluation

The treatment of wastewater from tannery industries poses significant challenges due to high levels of tannic acid and chemical oxygen demand (COD), along with low biodegradability. To address this issue, we conducted a study focusing on the use of Electrocoagulation (EC) as a treatment process for synthetic tannery wastewater. Iron (Fe) electrodes have been used as anode and cathode as well. The electrodes size (7 cm × 7 cm) has been used in this process. The investigation of removal efficiencies entailed the assessment of total organic carbon (TOC) and chemical oxygen demand (COD) as indicators of organic contaminant levels within the wastewater. The influence of current density, pH, flowrate, and time on the treatment was measured. At a current density of 51 A/m2 with 83.54 % of COD removal and 27 % of TOC removal were observed. The maximum COD removal was found at pH 4.93, flowrate 5 ml/min, current 0.953 A and time 115 min. The current investigation demonstrated the efficacy of the electrocoagulation process in reducing both total organic carbon (TOC) and chemical oxygen demand (COD) levels in synthetic tannery wastewater.

Seasonal variations of organophosphate esters (OPEs) in atmospheric deposition, and their contribution to soil loading

Organophosphate esters (OPEs) are ubiquitous in surface soil, and atmospheric deposition is considered to be the major pollution source. However, the research on the environmental transport behaviors of OPEs between atmospheric deposition and soil is very limited. In this study, we investigated the contamination levels and seasonal variations of OPEs in atmospheric deposition samples (n = 33) collected from an area of South China every month between February 2021 and January 2022, and evaluated the contribution of OPEs in atmospheric deposition to soil. The concentrations of ∑21target-OPEs ranged from 3670 to 18,600 ng/g dry weight (dw), with a mean of 8200 ng/g dw (median: 7600 ng/g dw). ∑21target-OPEs concentrations in all atmospheric deposition samples exhibited significant seasonal differences (p < 0.05) with higher concentrations observed in winter and lower concentrations in summer. Tris(2,4-di-tert-butylphenyl) phosphate (TDTBPP) was the most dominant target OPE in atmospheric deposition (4870 ng/g dw), and its seasonal variation trend was consistent with ∑21OPEs (p < 0.05). Simultaneously, in order to further explore the effect of atmospheric deposition on the levels of OPEs in soil of the study region, input fluxes and accumulation increments were estimated. Ten OPEs (including seven target OPEs and three suspect OPEs) exhibited high input flux means and accumulation increments, indicating that these compounds are prone to accumulate in soil via atmospheric deposition. It is noteworthy that the non-target phosphonate analyte bis(2,4-di-tert-butylphenyl) dibutyl ethane-1,2-diylbis(phosphonate) (BDTBPDEDBP) was detected at highest median concentration (8960 ng/g dw) in atmospheric deposition. Correspondingly, the average input flux and accumulation increment of BDTBPDEDBP were higher than those of all target and suspect OPEs. Collectively, this study quantifies the environmental transport behavior of OPEs between atmospheric deposition and soil, and provides new evidences for the fact that atmospheric deposition is the important pollution source of OPEs in soil.

Detecting galaxy tidal features using self-supervised representation learning

ABSTRACT Low surface brightness substructures around galaxies, known as tidal features, are a valuable tool in the detection of past or ongoing galaxy mergers, and their properties can answer questions about the progenitor galaxies involved in the interactions. The assembly of current tidal feature samples is primarily achieved using visual classification, making it difficult to construct large samples and draw accurate and statistically robust conclusions about the galaxy evolution process. With upcoming large optical imaging surveys such as the Vera C. Rubin Observatory’s Legacy Survey of Space and Time, predicted to observe billions of galaxies, it is imperative that we refine our methods of detecting and classifying samples of merging galaxies. This paper presents promising results from a self-supervised machine learning model, trained on data from the Ultradeep layer of the Hyper Suprime-Cam Subaru Strategic Program optical imaging survey, designed to automate the detection of tidal features. We find that self-supervised models are capable of detecting tidal features, and that our model outperforms previous automated tidal feature detection methods, including a fully supervised model. An earlier method applied to real galaxy images achieved 76 per cent completeness for 22 per cent contamination, while our model achieves considerably higher (96 per cent) completeness for the same level of contamination. We emphasize a number of advantages of self-supervised models over fully supervised models including maintaining excellent performance when using only 50 labelled examples for training, and the ability to perform similarity searches using a single example of a galaxy with tidal features.

Low-disturbance land remediation using vertical groundwater circulation well technology: The first commercial deployment in an operational chemical plant

Soil and groundwater contamination by organic pollutants from chemical plants presents significant risks to both environmental and human health. We report a significant field trial where a chemical plant in operation showed soil and groundwater pollution, as verified by sampling and laboratory tests. While many remediation methods are effective, they often require the temporary shutdown of plant operations to install necessary equipment. This paper introduces a novel combination of low-disturbance contaminant remediation technologies, including groundwater circulation well (GCW), pump and treat (P&T), and in-situ chemical oxidation (ISCO) technologies, that can be applied on the premises of an active plant without halting production. The groundwater with dissolved contaminants is removed through P&T and GCW, while GCW enhances ISCO that focus on eliminating the remaining hard-to-pump contaminants. Results show: (1) after two years of remediation effort, the contaminant levels in soil and groundwater were significantly reduced; (2) the average concentration reduction rate of four contaminants, including 1,2-dichloroethane, methylbenzene, ethylbenzene, and M&P-xylene, exceeds 98 %; (3) the presented remediation strategy results in the improvement of remediation efficiency. Specifically, the concentration of 1,2-dichloroethane in observation wells dropped from 40,550.7 μg/L to 44.6 μg/L. This study offers a first-of-its-kind commercial deployment of a GCW-based remediation strategy in an active plant setting. Moreover, the combined remediation approach presented here can serve as a model for designing contaminant remediation projects that require minimal operational disruption.