Lead System Research Articles

Optimizing Classroom Lighting: Balancing Illuminance Uniformity and Glare Control with Led Technology

Indoor lighting environment significantly impacts students’ concentration and learning performance. Optimal lighting conditions enhance reading speed, accuracy, and comprehension abilities. In contrast, poor lighting conditions may lead to decreased concentration and increased errors in tasks. Therefore, classroom lighting is an important factor to consider in classroom design to optimize cognitive efficiency of students. Current classroom lighting solutions using LED systems have met European Norm (EN) standard in terms of illuminance and energy efficiency. However, although the issue of glare has been addressed, it has not been completely resolved. This study introduces a solution for glare-free classroom lighting that maintains uniformity while adhering to existing standards. This approach aims to create a visually comfortable learning environment, balancing effective lighting with glare reduction.

Optimizing Sports Training Lessons by Using the Led System for Beginner Basketball Groups

Optimizing sports training lessons by using the LED system for beginner basketball groups. Objectives. This paper proposes the introduction into the training plan of the beginner basketball groups of some modern means, namely led systems for the development of reaction speed by making decisions to visual signals. The main pur-pose of this paper is to study the effects of this approach on the U13 players of the CSS Gheorgheni basketball team. Materials and methods: The subjects of the ex-periment were the athletes of the beginner basketball group born in 2010-2011, namely 16 girls. Initial tests were applied, then the players were subjected to specific training by applying some modern means, and at the end the same tests were ap-plied again. Results: At the first test on execution speed, we notice that all the ath-letes managed to improve their results. From the point of view of mistakes, also in this test, we notice that almost all the participants in the experiment improved their performance, three of them managing not to make any mistakes. In the throwing test, they all improved their performance. In the combined test (changes of direction and throwing in the basket) 7 athletes finished the route without any mistakes, 7 girls improved their performance, and 2 girls had the same number of mistakes. Conclusions: based on the results obtained, we can say with certainty that by using exercises based on an LED system for the development of reaction speed by making decisions to visual signals throughout the season, the performance of the sports-women under research has improved. Keywords: modern means, LED system, reaction speed

Innovative microbial water quality management in water distribution systems using in-pipe hydropowered UV disinfection: envisioning futuristic water-energy systems

ABSTRACT Hydropower UV disinfection has not been explored as a possible alternative for off-grid disinfection. Hydropowered UV LED technology was developed using off-the-shelf UV-C LEDs and pico – and femto-scale hydro turbine generators and evaluated across point-of-use relevant flow rates. Commercially available UV LED flow through reactors were subjected to microorganism challenge testing with 3 power schemes: wall-plug, hydropower, and hydropower-charged battery. UV LEDs powered by hydropower-charged battery demonstrated similar disinfection as wall-plug powered UV LEDs, achieving 0.5-1.8 MS2 log10 reduction at flow rates 0.5-2.3 L min−1, corresponding to reduction equivalent doses (RED) up to 16 or 30 mJ/cm2 for 254 and 285 nm, respectively. With hydropowered UV LEDs alone, MS2 log10 reduction decreased to <0.3 log10 reduction due to an underperforming and grossly inefficient turbine, with RED of 8 or 18 mJ/cm2 for 254 and 285 nm, respectively. Assessment of existing markets of UV disinfection systems and pico-hydro turbines demonstrated that hydropowered UV systems are already theoretically feasible for scales at point-of-entry (POE) and above. Economic feasibility will improve if turbines and/or UV system efficiencies improve. Prototype hydropower UV LED systems ranged from $145 to 220 depending on the UV LED reactor, and the battery system added $81. This study demonstrates the practicality of sustainable, renewable energy POU UV disinfection technology that can benefit decentralised, off-grid, rural and remote communities. The system may also scale up to provide renewable energy disinfection at larger scales, such as buildings and water distribution systems, for protecting human health in highly populated areas.

Light-mediated biosynthesis of size-tuned silver nanoparticles using Saccharomyces cerevisiae extract

Bio-based production of silver nanoparticles represents a sustainable alternative to commercially applied physicochemical manufacturing approaches and provides qualitatively highly valuable nanomaterials due to their narrow size dispersity, high stability and biocompatibility with broad application potentials. The intrinsic features of nanoparticles depend on size and shape, whereby the controlled synthesis is a challenging necessity. In the present study, the biosynthesis of size-tuned silver nanoparticles based on cell-free extracts of Saccharomyces cerevisiae DSM 1333 was investigated. Single parameter optimization strategies in phases of cultivation, extraction, and synthesis were performed to modify the nanoparticle scale and yield. Visible light was exploited as a tool in nanoparticle production. The influence of white light on the biosynthesis of silver nanoparticles was determined by using novel LED systems with the exposition of varying irradiation intensities and simultaneous performance of control experiments in the dark. Characterization of the resulting nanomaterials by spectrophotometric analysis, dynamic light scattering, scanning electron microscopy, and energy dispersive X-ray spectroscopy, revealed spherical silver nanoparticles with controlled, light-mediated size shifts in markedly increased quantities. Matching of irradiated and non-irradiated reaction mixtures mirrored the enormous functionality of photon input and the high sensitivity of the biosynthesis process. The silver nanoparticle yields increased by more than 90% with irradiation at 1.0±0.2mWcm-2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$1.0 \\pm 0.2\ ext{ mW }{\ ext{cm}}^{-2}$$\\end{document} and the reduction of particle dimensions was achieved with significant shifts of size-specific absorption maxima from 440 to 410 nm, corresponding to particle sizes of 130 nm and 100 nm, respectively. White light emerged as an excellent tool for nano-manufacturing with advantageous effects for modulating unique particle properties.Graphical abstract

P-EcStat: A Versatile Design of Photoelectrochemical and Electrochemical Sensing System with Smartphone Interface via Bluetooth Low Energy

Electrochemical and photoelectrochemical sensors are a rapidly developing field in analytical chemistry. However, commercial systems often lack versatility and affordability, hindering wider adoption. Additionally, the absence of integrated excitation light sources limits their application in photoelectrochemical sensing. Here, we present a highly precise, versatile, affordable measurement system for both electrochemical and photoelectrochemical sensing applications. The system incorporates a three-electrode potentiostat with a synchronized excitation light source. This design enables the system to perform conventional electrochemical measurements like cyclic voltammetry, chronoamperometry, and photoelectrochemical amperometric measurements with controlled light excitation. The developed measurement system operates within a voltage range suitable for a measurable current range of 1 nA to 18 mA, with a high precision of 99%. The excitation source is a monochromatic LED system offering seven distinct wavelengths with digitally controlled intensity via a digital-to-analog converter. Furthermore, an Android-based user interface allows wireless system control via Bluetooth Low Energy. The report also details the construction of a photoelectrochemical experiment using copper (II) oxide nanorods synthesized by the hydrothermal process as the photoactive material employed to test the experiment on a potassium ferricyanide/potassium ferrocyanide solution. This user-friendly system allows broader exploration of electrochemical and photoelectrochemical sensing applications.

Energy Efficiency in Public Lighting Systems Friendly to the Environment and Protected Areas

Solid-state lighting technology, such as LED devices, is critical to improving energy efficiency in street lighting systems. In Ecuador, government policies have established the obligation to exclusively use LED systems starting in 2023, except in special projects. Ecuador, known for its vast biodiversity, protects its national parks, which are rich in flora, fauna and natural resources, through international institutions and agreements such as UNESCO, CBD and CITES. Although reducing electrical consumption usually measures energy efficiency, this article goes further. It considers aspects such as the correlated color temperature in the lighting design of protected areas, light pollution and the decrease in energy quality due to harmonic distortion. Measurements of the electromagnetic spectrum of the light sources were made in an area in the Galápagos National Park of Ecuador, revealing highly correlated color temperatures that can affect ecosystem cycles. In addition, the investigation detected levels of light pollution increasing the night sky brightness and a notable presence of harmonic distortion in the electrical grid. Using simulations to predict the behavior of these variables offers an efficient option to help preserve protected environments and the quality of energy supply while promoting energy savings.

Performance of high-efficiency UV-C LEDs in water disinfection: Experimental, life cycle assessment, and economic analysis of different operational scenarios

The widespread use of low or medium pressure mercury lamps in UV-C water disinfection should consider recent advances in UV-C LED lamps that offer a more sustainable approach and avoid its main drawbacks. The type of water and the mode of operation are critical when deciding on the treatment technology to be used. Therefore, this study investigates the potential application of UV-C LED disinfection technology in terms of kinetics, environmental assessment, and economic analysis for two scenarios: the continuous disinfection of a wastewater treatment plant (WWTP), and disinfection of harvested rainwater (RWH) in a residential household that operates intermittently. Experiments are conducted using both the new UV-C LED system and the conventional mercury lamp to disinfect real wastewater. Removal of total coliforms and Escherichia coli bacteria, with concentrations of approximately 105 and 104 CFU per 100 mL has been followed to assess the performance of both types of UV-C lamps. The experimental study provides kinetic parameters that have been further used in the environmental assessment conducted from a life cycle perspective. Additionally, considering the significant role of electricity consumption, a preliminary economic analysis has been conducted. The results indicate that first-order kinetic constants of pathogens removal with UV-C LEDs achieve 1.4 times higher values than Hg lamp. Regarding the environmental and economic assessment, for disinfection systems operating continuously, LEDs result in environmental impacts 5 times higher than Hg lamp in most categories, indicating that Hg lamps offer a viable option both from economic and environmental point of view. However, for installations with intermittent operation, LEDs emerge as the most competitive alternative, due to their ability to be turned on and off without affecting their lifespan. This study shows that UV-C LED lamps hold promise to replace conventional mercury lamps in a near future.

Sintering Behavior and Thermal Properties of Cu-Graphite Materials by a Spark Plasma Sintering Method

The use of heat dissipation materials in various field such as power semiconductor device, LED and microelectronic system. Therefore, there is a need for heat dissipation materials using copper (Cu) and graphite (Gr). These materials have high thermal conductivity. In particular, graphite has high thermal stability with a low coefficient of thermal expansion. This study was conducted to enhance the thermal properties of Cu for use in heat dissipation materials, using a spark plasma sintering method. Cu-Gr powders were mixed by a shaking mixer and fabricated with volume fractions of 7:3, 6:4, 5:5, 4:6 and 3:7. The spark plasma sintering method is a uniaxial pressurization process, which can control the direction of Gr. The Cu-Gr powders were sintered at a temperature of 850 oC at a heating rate of 30 oC/min and a sintering pressure of 40MPa. Consequently, as the Gr contents were increased, the relative densities of the Cu-Gr composites decreased from 99.25 to 94.85%. Gr has high resistance to high-temperature deformation, which contributed to a decrease in shrinkage and relative density. The highest thermal conductivity was measured at 539.7 W/ m·K for a Cu-Gr volume ratio of 5:5. The thermal conductivity of the directionally controlled Gr was measured to be about 20-30 W/m·K higher than the uncontrolled sample. Furthermore, the TDP (Thermal distortion parameter), for which a lower value indicates better thermal stability, was systematically investigated.

Lake Environmental Data Harvester (LED) for Alpine Lake Monitoring with Autonomous Surface Vehicles (ASVs)

This article introduces the Lake Environmental Data Harvester (LED) System, a robotic platform designed for the development of an innovative solution for monitoring remote alpine lakes. LED is intended as the first step in creating portable robotic tools that are lightweight, cost-effective, and highly reliable for monitoring remote water bodies. The LED system is based on the Shallow-Water Autonomous Multipurpose Platform (SWAMP), a groundbreaking Autonomous Surface Vehicle (ASV) originally designed for monitoring wetlands. The objective of LED is to achieve the comprehensive monitoring of remote lakes by outfitting the SWAMP with a suite of sensors, integrating an IoT infrastructure, and adhering to FAIR principles for structured data management. SWAMP’s modular design and open architecture facilitate the easy integration of payloads, while its compact size and construction with a reduced weight ensure portability. Equipped with four azimuth thrusters and a flexible hull structure, SWAMP offers a high degree of maneuverability and position-keeping ability for precise surveys in the shallow waters that are typical of remote lakes. In this project, SWAMP was equipped with a suite of sensors, including a single-beam dual-frequency echosounder, water-quality sensors, a winch for sensor deployment, and AirQino, a low-cost air quality analysis system, along with an RTK-GNSS (Global Navigation Satellite System) receiver for precise positioning. Utilizing commercial off-the-shelf (COTS) components, a Multipurpose Data-Acquisition System forms the basis for an Internet of Things (IoT) infrastructure, enabling data acquisition, storage, and long-range communication. This data-centric system design ensures that acquired variables from both sensors and the robotic platform are structured and managed according to the FAIR principles.

Simultaneous Multi-frequency lock-in Thermography: A new flexible and effective Active Thermography scheme

A new active thermography scheme is here introduced, referred as ”‘Multi-Frequency Thermography”’, which uses an optimized multi-tone signal for simultaneously implementing lock-in analysis on a discrete and arbitrary set of linearly spaced frequencies. Such a signal, which modulates the intensity of the heating source here being a LED system in the visible range, results from the non-trivial summation of a desired number of odd and even harmonics of a fundamental tone, each of them having a specific initial phase value but equal amplitude, so as to deliver the same energy amount for all the chosen frequencies. In this way, a discrete set of thermal waves having different diffusion lengths are simultaneously excited within the inspected sample to probe different depths into it. With respect to standard lock-in thermography, it is demonstrated that the proposed approach can extract amplitude and phase features for all the excited frequencies from a single measurement, which lasts as long as a lock-in implemented at the fundamental tone. Both quantitative and qualitative comparisons with standard lock-in thermography are here reported, showing an excellent agreement. Hence, this new active thermography scheme can provide several advantages in practical implementations of thermography nondestructive evaluation.

Development of a novel laboratory photodynamic therapy device: automated multi-mode LED system for optimum well-plate irradiation

HighlightsMulti-mode Automated Well-plate PDT LED Laboratory Irradiation System described.Automates and standardizes time-consuming experiments.LED wavelength and temperature stabilized for highly reproducible irradiations.Efficacy demonstrated in 5-aminolevulinic acid (5-ALA) treatments of HT-29 colon cancer cells and WI-38 human lung fibroblasts.

Investigating a batch-flow photocatalytic LED system for diclofenac removal in wastewater treatment plants: Assessing the influence of reaction conditions on photocatalytic efficiency

This work introduces an innovative batch-flow photocatalytic LED system aimed at efficiently removing diclofenac from wastewater. The study highlights the novelty of fabricating TiO2-loaded carbon fiber photocatalysts through a hydrothermal process, exhibiting a blue shift in their absorption spectrum and enhancing their photon absorption capability. A crucial design feature is the spectral matching between the LED light source and the photocatalyst, which is critical for achieving high photodegradation efficiency. A significant innovation of our study is the testing of the system under real conditions at an operational sewage treatment plant. Here, the designed system demonstrated high efficacy in degrading diclofenac across various treatment stages, highlighting its robustness and adaptability to changing environmental conditions. The highest degradation efficiency was achieved with sewage from the secondary settling tank, where nearly 90 % efficiency was observed after 6 h of irradiation. Moreover, the use of renewable energy sources emphasizes the system's sustainability, presenting a greener alternative to traditional wastewater treatment methods. The investigation not only showcases the system's effectiveness in diclofenac degradation but also its adaptability and stability under real-world conditions, marking a significant advancement in sustainable wastewater treatment technologies.

Inactivation kinetics of polyphenol oxidase and peroxidase enzymes in buffer solutions by ultraviolet light sources at multiple UV-C wavelengths

This study aimed to evaluate the effect of multiple wavelengths of UV-C light sources on the inactivation of polyphenol oxidase (PPO) and peroxidase (POD) in buffer solutions. Enzyme solutions were treated with a UV-C excimer lamp (EL) emitting at 222 nm, low-pressure mercury (LPM) lamp at 253.7 nm, four UV-LEDs sources emitting at 255, 265, 275 and 285 nm, and a novel pulsed UV-C lamp (PL) emitting at 232, 242, 261 and 272 nm. Three kinetic models were used to compare UV-C wavelengths enzymatic inactivation efficacy considering the volume average fluence for 90% reduction (HD). Validation of kinetic parameters was performed under continuous-flow treatment in a UV-C LED and EL system. EL treatment resulted in the highest inactivation efficacy of PPO and POD enzymes with HD of 52.8 and 74.8 mJ/cm2, respectively. PL inactivation efficacy for both enzymes was higher than with LPM lamp or UV-LEDs. The two-component first-order model best described the inactivation of PPO and POD in a buffer solution. The adjusted kinetic parameters for this model were validated under UV-C light continuous flow processing. This study contributes to the development of liquid food treatment by ultraviolet technology.

Light emitting diode and laser diode system behaviour description and their performance signature measurements

Abstract This paper has clarified the light emitting diode and laser diode system behaviour description and their external quantum efficiency measurements. Light output of LED spontaneous emission and laser diode stimulated emission are clarified. Stimulated and amplified spontaneous emission of laser diode and LED system configuration are demonstrated. The management of hybrid light sources spectrum illumination interaction for efficient solar cells light intensity and short circuit current density enhancement. The laser diode has presented better performance in the light output power especially under the same temperature effects. It is ensured that the dramatic effects of the temperature on both laser diode performance efficiency.

Optimizing anti-perturbation capability in single-shot wide-field multimode fiber imaging systems

In recent years, multimode fiber (MMF) has emerged as a focal point in ultrathin endoscopy owing to its high-capacity information transmission. Nevertheless, the technology's susceptibility to external perturbances limits its practical applications. In this study, we employ a single MMF as both the illumination unit and imaging probe and utilize this single-shot wide-field MMF imaging system to investigate the impact of LED and laser sources on anti-perturbation capabilities. Experimental results demonstrate that, in the absence of deformations in the MMF, both LED and laser-based systems achieve an average structural similarity (SSIM) index of around 0.8 for the reconstructed image, utilizing advanced deep learning techniques, with the laser-based system performing slightly better. However, under unknown MMF configurations post-deformation, the SSIM remains robust at 0.67 for the LED-based system, while the laser-based system drops the average SSIM to 0.45. The results reveal that LED has anti-perturbation capability in single-shot wide-field MMF imaging systems. These findings indicate significant potential for future anti-perturbation studies in endoscopy employing MMF imaging.

New MoS2/Tegafur-Containing Pharmaceutical Formulations for Selective LED-Based Skin Cancer Photo-Chemotherapy.

Non-melanoma skin cancer (NMSC) is one of the most common types of cancer worldwide. Despite the low mortality rate, rising incidence and recurrence rates are a burden on healthcare systems. Standard treatments such as chemotherapy, radiotherapy, and surgery are either invasive or toxic to healthy tissues; therefore, new, alternative, selective treatments are needed. In this work, a combined photothermal and chemotherapeutic approach is proposed. MoS2 was used as photothermal agent. It was prepared by a liquid-phase exfoliation and intercalation method using polyvinylpyrrolidone (PVP), followed by recirculation through a custom-built high-power ultrasonication probe. After 6 h of ultrasonication treatment, the average particle size was 165 ± 170 nm. Near-infrared (NIR) irradiation assays (810 nm, 0.1 W/cm2, 30 min, 180 J/cm2) confirmed that MoS2 nanosheets can efficiently convert NIR light into heat and reach 52 °C. The therapeutic doses of MoS2 (125 µg/mL) and Tegafur (50 µg/mL) were optimized and both were simultaneously incorporated into a Carbopol hydrogel. The cells were brought into contact with the hydrogel and irradiated with a custom-built NIR LED system. In HFF-1 cells (normal human fibroblasts), the metabolic activity was 78% (above the 70% toxicity limit-ISO 10993-5:2009(E)), while in A-431 skin cancer cells, it was 28%. In addition, the MoS2 + Tegafur hydrogels led to a 1.9-fold decrease in A-431 cancer cell metabolic activity, 72 h after irradiation, in comparison to MoS2 hydrogels, indicating a combined effect of photothermal and chemotherapy.

Junction temperature and luminous flux prediction for white LED array based on electrical-photo-thermal modeling

During the operation of an LED array, its thermal and optical performances are always not equal to the superposition of the individual LED's characteristics because of a significant thermal coupling effect between the arrays. Based on this, this paper proposes an electrical–photo-thermal model, with considering both junction temperature and luminous flux, to predict the both the thermal and optical performances of LED arrays operated under different currents, case temperatures, and lighting methods. The junction temperature and luminous flux of a single LED operating under different driving currents and case temperature conditions are firstly collected to establish the luminous flux response surface model of a single chip. Then it is used to predict the luminous flux of an array, whose junction temperature is predicted using both thermal coupling matrix (TCM) and numerical models. Experiments verify the luminous flux of the LED array under different operation conditions and show that the proposed electrical–photo-thermal modeling can be used to predict the thermal and optical parameters of LED arrays with 95 % accuracy. Thus, it is effective for the fast prediction of the junction temperature and luminous flux of large LED systems with array structures, i.e. intelligent automotive lightings and displays.

МОДЕЛЮВАННЯ ПРОЦЕСІВ СТВОРЕННЯ СВІТЛОВОГО ПРОСТОРУ У БАКТЕРИЦИДНИХ УЛЬТРАФІОЛЕТОВИХ СВІТЛОДІОДНИХ УСТАНОВКАХ

The pandemic continues, as does the issue of preventing environmental pollution with harmful substances, viruses and bacteria. In these conditions, lighting technology and disinfection technologies based on the use of radiation in the ultraviolet spectral range open up wide opportunities. The relevance of the topic lies in the fact that modern events, namely pandemics, earthquakes, volcanic eruptions, tsunamis and wars, cause a large amount of environmental pollution with harmful substances, various viruses and bacteria. Unfortunately, these problems have affected the entire population of our planet, and in the future, without solving the issue of high-quality disinfection of various environments, they may lead to new, larger-scale disasters. The research was carried out in O.M. Beketov National University of Urban Economy in Kharkiv was allowed to establish the possibility of using ultraviolet LEDs for the treatment of various environments infected with harmful microorganisms and Covid-19, to develop a method for modeling the curve of light intensity of a light device and an algorithm for calculating LED installations, which will provide the possibility of calculating and designing such installations for the disinfection of various environments, in particular, water environments and environments infected with Covid-19. Thus, studies have confirmed the possibility of using ultraviolet LEDs to disinfect the environment from particles of the Covid-19 virus, harmful microorganisms in 193various environments and to establish requirements for bactericidal installations in these conditions. And the developed method can be applied to any arbitrarily selected observation points, bases of LEDs and their environment, which makes the algorithm suitable for calculating light distribution from LED systems for bactericidal disinfection of various environments, including water or infected with Covid-19, from harmful microorganisms.

Long-Term Monitoring Campaign of LED Street Lighting Systems: Focus on Photometric Performances, Maintenance and Energy Savings

The renovation of public lighting installations by replacing the traditional systems with LED technologies and introducing smart lighting control systems is a policy widely adopted to contain energy consumption and expenditure. Additionally, the long-term monitoring of the depreciation of the new lighting systems is a crucial issue. The aim of this study is to report the results of in-field measurements of new LED lighting systems in the city of Turin (Italy). A method was defined to assess: (i) energy performance (through data from the remote-control system); (ii) photometric performance (through in-field measurement campaigns); and (iii) depreciation of the photometric performance over a period of approximately 5 years. Results demonstrated that the new LED systems allow us to achieve an average energy saving of 51% compared to the ex-ante condition, improving the photometric performances and compiling the standard requirements by lowering the over-illumination levels. Moreover, the measured depreciation of the LED systems over time was compared with the predicted depreciation, estimated based on the calculation method proposed in Standards BS 5489-1:2020 and ISO/CIE TS 22012:2019. The results obtained showed that the measured depreciation of the photometric performance was closer to the predicted depreciation trend according to BS 5489-1:2020 (variations between 0% and 4%), while greater variations (between 17% and 23%) emerged considering the ISO/CIE TS 22012:2019.

Multispectral Imaging based on a Multichannel LED System and RGB Camera

Multispectral Imaging based on a Multichannel LED System and RGB Camera