Leakage Fractions Research Articles

The Impact of Leak Gap Size and Position on Surgical Mask Performance of Source Control: A Numerical Study

Surgical masks are widely used for infectious source control by preventing infected individuals from transmitting pathogens. However, poor fit can create gaps between the mask and face, reducing their effectiveness. In this study, a numerical model was developed based on realistic surgical mask geometry with peripheral gaps of varying sizes and positions, fitted onto a breathing manikin. Exhalation leakage airflow dynamics and aerosol pathogen dispersion were investigated using a validated computational fluid dynamics (CFD) model with porous media. Results indicate that despite the presence of leaks, surgical masks are effective in controlling the spread of pathogens, with maximum airflow leakage at 9.11% and pathogen leakage at 16.83%. The average velocity of leaked airflow ranged from 0.12 m/s to 1.43 m/s, depending on the gap size and position. The position of the gap had little impact on the airflow and pathogen leakage fractions. Correlations between the average velocity of net leakage flow, leakage fractions of airflow and pathogens, and gap size were developed. Pathogens spread most widely from bottom leaks, followed by side and top leaks, with bottom leaks releasing up to 9.7 times more contaminated air than top leaks and 6.5 times more than side leaks. The findings also suggest that smaller gaps are associated with higher initial velocities of leakage, which in turn lead to wider dispersion of pathogens.

Visualization and Quantification of Facemask Leakage Flows and Interpersonal Transmission with Varying Face Coverings

Although mask-wearing is now widespread, the knowledge of how to quantify or improve their performance remains surprisingly limited and is largely based on empirical evidence. The objective of this study was to visualize the expiratory airflows from facemasks and evaluate aerosol transmission between two persons. Different visualization methods were explored, including the Schlieren optical system, laser/LED-particle imaging system, thermal camera, and vapor–SarGel system. The leakage flows and escaped aerosols were quantified using a hotwire anemometer and a particle counter, respectively. The results show that mask-wearing reduces the exhaled flow velocity from 2~4 m/s (with no facemask) to around 0.1 m/s, thus decreasing droplet transmission speeds. Cloth, surgical, and KN95 masks showed varying leakage flows at the nose top, sides, and chin. The leakage rate also differed between inhalation and exhalation. The neck gaiter has low filtration efficiency and high leakage fractions, providing low protection efficiency. There was considerable deposition in the mouth–nose area, as well as the neck, chin, and jaw, which heightened the risk of self-inoculation through spontaneous face-touching. A face shield plus surgical mask greatly reduced droplets on the head, neck, and face, indicating that double face coverings can be highly effective when a single mask is insufficient. The vapor–SarGel system provided a practical approach to study interpersonal transmission under varying close contact scenarios or with different face coverings.

Impacts of Mask Wearing and Leakages on Cyclic Respiratory Flows and Facial Thermoregulation

Elevated face temperature due to mask wearing can cause discomfort and skin irritation, making mask mandates challenging. When thermal discomfort becomes intolerable, individuals instinctively or unknowingly loosen or remove their facemasks, compromising the mask’s protective efficacy. The objective of this study was to numerically quantify the microclimate under the mask and facial thermoregulation when wearing a surgical mask with different levels of misfit. An integrated ambient–mask–face–airway computational model was developed with gaps of varying sizes and locations and was validated against complementary experiments. The low Reynolds number (LRN) k-ω turbulence model with porous media was used to simulate transient respiratory flows. Both skin convective heat transfer and tissue heat generation were considered in thermoregulation under the facemask, besides the warm air exhaled from the body and the cool air inhaled from the ambient. The results of this study showed that when wearing a surgical mask with a perfect fit under normal breathing, the temperature at the philtrum increased by 4.3 °C compared to not wearing a mask. A small gap measuring 0.51 cm2 (gap A) at the nose top resulted in 5.6% leakage but reduced the warming effect by 28% compared to zero gap. Meanwhile, a gap of 4.3 cm2 (R1L1) caused 42% leakage and a 62% reduction in the warming effect. Unique temporospatial temperature profiles were observed at various sampling points and for different gap sizes, which correlated reasonably with the corresponding flow dynamics, particularly close to the gaps. The temperature change rate also exhibited patterns unique to the gap site and sampling point, with distinctive peaks occurring during the inspiratory–expiratory flow transitions. These results have the significant implications that by using the temporospatial temperature profiles at several landmark points, the gap location can potentially be pinpointed, and the gap size and leakage fractions can be quantified.

Assessment of the clinical feasibility of detecting subtle blood-brain barrier leakage in cerebral small vessel disease using dynamic susceptibility contrast MRI

PurposeCerebral small vessel disease (cSVD) involves several pathologies affecting the small vessels, including blood-brain barrier (BBB) impairment. Dynamic susceptibility contrast (DSC) MRI is sensitive to both blood perfusion and BBB leakage, and correction methods may be crucial for obtaining reliable perfusion measures. These methods might also be applicable to detect BBB leakage itself. This study investigated to what extent DSC-MRI can measure subtle BBB leakage in a clinical feasibility setting. MethodsIn vivo DCE and DSC data were collected from fifteen cSVD patients (71 (±10) years, 6F/9M) and twelve elderly controls (71 (±10) years, 4F/8M). DSC-derived leakage fractions were obtained using the Boxerman-Schmainda-Weisskoff method (K2). K2 was compared with the DCE-derived leakage rate Ki, obtained from Patlak analysis. Subsequently, differences were assessed between white matter hyperintensities (WMH), cortical gray matter (CGM), and normal-appearing white matter (NAWM). Additionally, computer simulations were performed to assess the sensitivity of DSC-MRI to BBB leakage. ResultsK2 showed significant differences between tissue regions (P < 0.001 for CGM-NAWM and CGM-WMH, and P = 0.001 for NAWM-WMH). Conversely, according to the computer simulations the DSC sensitivity was insufficient to measure subtle BBB leakage, as the K2 values were below the derived limit of quantification (4∙10−3 min−1). As expected, Ki was elevated in the WMH compared to CGM and NAWM (P < 0.001). ConclusionsAlthough clinical DSC-MRI seems capable to detect subtle BBB leakage differences between WMH and normal-appearing brain tissue it is not recommended. K2 as a direct measure for subtle BBB leakage remains ambiguous as its signal effects are due to mixed T1- and T2∗-weighting. Further research is warranted to better disentangle perfusion from leakage effects.

Impacts of Sandstorms on Chemistries of Ambient PAHs in a Small City in North China

Sandstorm events frequently perplex northern China, addressing the people's concern due to subsequent increases in the toxicity and carcinogenicity of PM2.5-bound PAHs (PB-PAHs) in receptor area of sand dust. Here, we enacted a field campaign in a small city between Beijing and Baoding in spring of 2021 covering the sandstorm period (SSP) and non-sandstorm period (NSSP) to examine the sandstorm impacts on chemistries of PB-PAHs. SSP exhibited a slightly high average PAH concentrations of 10.3 ng m–3 than 9.16 ng m–3 in the NSSP. At the same time, the average PM2.5 concentrations obviously increased from 60.7 μg m–3 to 75.2 μg m–3. Positive matrix factorization (PMF) analysis manifested that sandstorm largely enhanced the oil leakage and combustion (OLC) fractions from 18.0% in the NSSP to 34.4% in the SSP. Potential source contribution function (PSCF) indicated that OLC partly came from sandstorm origin area–Inner Mongolia. Low diagnostic ratios of FA / (FA + PY) in the SSP also indicated OLC was more important. Accordingly, the largest contributor of incremental lifetime cancer risks (ILCRs) changed from vehicle exhaust (VE) (36.2%) in the NSSP to OLC (34.4%) in the SSP. VE and industrial emission (IE) contributions decreased obviously due to emission control and traffic limitation in the SSP. Coal burning (CB) still held a high contribution to PAHs regardless of the implementation of “coal to gas” law in the sampling area. In addition, sandstorms increased the levels of high molecular weight PAHs (HMW-PAHs) with high toxicity by 4.07%. ILCRs for adults and children increased from 3.90 × 10–7 to 4.74 × 10–7 and from 2.41 × 10–7 to 2.93 × 10–7, respectively, in the SSP, which should be more concerned.

Determination of radon leakage from sample container for gamma spectrometry measurement of 226Ra

Gamma spectrometry is widely used for radionuclide activity measurement of environmental sample including 226Ra in soil because it is versatile, easy to implement, non-destructive, and relatively cheap compared to other methods. By gamma spectrometry, 226Ra can be determined directly using its energy peak of 186.2 keV or indirectly by its decay products which are in secular equilibrium with 226Ra, i.e. 214Bi and 214Pb. However, both methods have challenges where for direct measurement, interfering from 235U energy peak of 185.7 keV can add significant contribution to the 186.2 keV of 226Ra gamma peak while for indirect measurement using energy peaks of 214Bi and 214Pb, decay products of 222Rn gas, longer time (at least 21 days) for their equilibrium ingrowth is needed and radon tightness of sample container must be ensured. In some measurements, the equilibrium could not be reached due to radon leakage from sample container. Therefore, in this paper, the radon leakage fraction from three different sealing methods of Marinelli beaker used in soil activity measurement were studied using HPGe detector and radon accumulation chamber with RAD7. The three sealing methods were only lid without sealing (MB1), sealed with paraffin film (MB2), sealed with silicone glue and vacuumed plastic bag (MB3) and their leakage fractions were 53%, 30%, and negligible leakage, respectively. Significant radon leakage from MB1 and MB2 have caused underestimation of 226Ra activity concentration measured by indirect gamma spectrometry. The study result recommends using MB3 sealing method for gamma spectrometry measurement because it is simple and cheap and has negligible leakage, moreover, its vacuumed plastic bag facilitates visual inspection to possible radon leakage.

Potential fuel cycle performance of floating small modular light water reactors of Russian origin

We examine the potential fuel cycle performance of high assay low-enriched uranium fueled small light water reactors by considering several floating small reactor concepts of Russian origin with 235U enrichment at 10%, 15%, and 19.7%. These enrichments are generic but representative of the reactor concepts being considered. The small reactor concepts were considered parametrically at two different power densities and neutron leakage fractions. The analysis was performed for the U.S. Department of Energy Office of Nuclear Energy using the evaluation metrics from the Evaluation and Screening (E&S) Study. The reference reactor system in a once-through fuel cycle with an enrichment greater than 5%, but less than 20%, in the E&S study is a graphite-moderated modular high temperature gas-cooled reactor (mHTGR). The neutron spectrum of an mHTGR is very different from these Russian floating small reactor concepts, which is why this analysis was conducted.The fuel cycle analysis indicates that increasing core leakage negatively impacts the natural resource requirements as well as the spent nuclear fuel and high-level waste radioactivity normalized to a giga-watt electric year (GWe-yr) basis. Further, we found that the 235U enrichment of the fuel and the rated core power density have limited fuel cycle performance impacts. One impact is the slightly higher discharge burnup of the de-rated power cases resulting in different spent nuclear fuel and high-level waste radioactivity at 100 and 100,000 years after fuel discharge. The most significant result from the study is the observation that all the enrichment and power density cases resulted in decreased radioactivity at 100,000 years relative to the reference mHTGR example case with 15.5%-enrichment from the E&S study.

In-vitro characterization of self-expandable textile transcatheter aortic valves

ObjectiveThis study aims at assessing the global dynamic behavior, closing energy and turbulence characteristics of self-expandable textile (inclined and straight yarn) transcatheter aortic valves (TAV) versus bioprosthetic TAVs. MethodsTwo self-expandable textile TAVs one with inclined yarn textile and another with straight yarn textile leaflets were assessed in a pulse duplicator and compared with a self-expandable commercial bioprosthetic TAV under physiological pressure and flow. Particle Image Velocimetry and high-speed imaging were performed. Effective orifice areas (EOA), leakage fractions (LF), Pinwheeling indices (PI), closing energy (E), viscous shear stresses (VSS) and Reynolds shear stresses (RSS) were calculated. Results(a) EOAs and LFs were 2.27 ± 0.03 cm2, 31.7 ± 0.6%; 2.25 ± 0.08 cm2, 26.6 ± 0.7%; and 1.63 ± 0.01 cm2, 29.1 ± 1.25% for inclined textile, bioprosthetic and straight textile TAV respectively (p < 0.0001). (b) Following same order, PIs were significantly different going from 1.16 ± 0.21%, 8.48 ± 0.8% and 8.865 ± 0.58% with the exception of CoreValve and straight yarn valve (p = 0.37); (c) E is lowest for straight textile TAV (0.0024 ± 0.0017 J), followed by bioprosthetic valve (0.00259 ± 0.0011 J) and then 45° Oriented Yarn Valve (0.00334 ± 0.03 J) (d) At peak systole, the highest RSS distribution was with the Straight textile TAV reaching up to 330Pa. The bioprosthetic TAV shows the smallest range with RSS reaching around 230Pa and the inclined textile TAV up to 280Pa. VSS limits were comparable among the 3 valves ranging between 5.2Pa and 5.7Pa. ConclusionHemodynamic similarities were found between the textile self-expandable valves and the bioprosthetic valve. This study constitutes another step towards showing the potential that textile valves have to become an alternative for the biological ones.

The leakage of sewer systems and the impact on the 'black and odorous water bodies' and WWTPs in China.

China has achieved significant progress on wastewater treatment and aquatic environmental protection. However, leakage (in- and exfiltration) of sewer systems is still an issue. By using the statistical data of water and wastewater in 2016 in China, and the person loads (PLs) of water and wastewater in Singapore, the leakage fractions of hydraulic flow, organic carbon (COD), nitrogen (N) and phosphorus (P) mass loading, and in-sewer COD biological removal in the sewer systems of China (except Hong Kong, Macau and Taiwan), Shanghai, Guangzhou and Beijing were reported for the first time. The fractions of hydraulic flow infiltration (13%, Shanghai and Guangzhou) and exfiltration (39%, China) were calculated. Except Beijing, whose sewer networks are under appropriate management with small leakage fractions, the exfiltration fractions of COD (including in-sewer biological COD removal) ranged from 41% (Shanghai) to 66% (China) and averaged 55%; N ranged from 18% (Shanghai) to 48% (China) and averaged 33%; and P ranged from 23% (Shanghai and Guangzhou) to 44% (China) and averaged 30%. The exfiltrated sewage, COD, N and P not only wastes resources, but also contaminates the aquatic environment (especially groundwater) and contributes to 'black and odorous water bodies'. In- and exfiltration in the sewer network leads to low influent COD concentration, C/N ratio and high inorganic solids and inert particulate COD concentrations of many municipal wastewater treatment plants (WWTPs) causing high cost for nutrient removal, poor resource recovery, additional reactor/settler volume requirement and other operational problems. Therefore, tackling sewer leakage is of primary importance to today's environment in China. Recommendations for the inspection of sewer systems and the rehabilitation of damaged sewers as well as the development of design and operation guidelines of municipal WWTPs tailored to the specific local sewage characteristics and other conditions are proposed.

Stented valve dynamic behavior induced by polyester fiber leaflet material in transcatheter aortic valve devices.

This study aims at assessing the global dynamic behavior, elastic deformability, closing energy and turbulence of rigid versus deformable stented (RS vs DS) valve systems with deformable and rigid textile materials (DT vs RT) through studying the stent-valve interaction compared to a bioprosthetic material in transcatheter aortic valves (TAV). Three 19 mm stented textile TAV designs (RS-DT, RS-RT and DS-RT) with different stent and leaflet properties were tested and compared with a control bioprosthetic TAV (RS-DB) in a left heart simulator flow loop under physiological pressure and flow. Particle Image Velocimetry and high speed imaging were performed. Pressure gradients (PG), leakage fractions (LF), Pinwheeling indices (PI), closing energy (E) and Reynolds shear stresses (RSS) were calculated. (a) PGs and LFs were 11.86 ± 0.51 mmHg, 11.70 ± 0.34%; 8.84 ± 0.40 mmHg, 29.80 ± 0.76%; 11.59 ± 0.12 mmHg, 14.23 ± 1.64%; and 7.05 ± 0.09 mmHg, 12.08 ± 0.45% % for RS-DB, RS-DT, RS-RT and DS-RT respectively. (b) PIs were 15.79 ± 2.34%, 4.36 ± 0.84%, 2.47 ± 0.51% and 2.03 ± 0.33% for RS-DB, RS-DT, RS-RT and DS-RT respectively. (c) E is lowest for DS-RT (0.0010 ± 0.0002 J) followed by RS-RT (0.0017 ± 0.0002 J), RS-DB (0.0023 ± 0.0004 J) and highest with RS-DT (0.0036 ± 0.0007 J). (d) At peak systole lowest RSS was obtained with RS-DT (87.82 ± 0.58 Pa) and highest with DS-RT (122.98 ± 1.87 Pa). PGs, LFs, PIs and E were improved with DS-RT compared to other textile TAVs and RS-DB. Despite achieving more RSS than the rest of TAVs, DS-RT still falls within the same range of RSS produced by the other 2 valves and control exceeding the threshold for platelet activation.

Implantation Depth and Rotational Orientation Effect on Valve-in-Valve Hemodynamics and Sinus Flow

This study evaluated the effect of transcatheter aortic valve implantation depth and rotation on pressure gradient (PG), leakage fractions (LF), leaflet shear stress, and sinus washout in an effort to understand factors that may dictate optimal positioning for valve-in-valve (ViV) procedures. Sinus flow stasis is often associated with prosthetic leaflet thrombosis. Although recent ViV invitro studies highlighted potential benefits of transcatheter aortic valve supraannular implantation to minimize PGs, the relationship between transcatheter aortic valve depth and other determinates of valve function remains unknown. Among these, LFs, shear stress, and poor sinus washout have been associated with poorer valve outcomes. ViV hemodynamic performance was evaluated invitro vs axial positions -9.8, -6.2, 0, and+6 mm and angular orientations 0, 30, 60, and 90 degrees in a degenerated surgical aortic valve. PGs, LFs, and sinus shear stress and washout were compared. Leaflet high-speed imaging and particle-image velocimetry were performed to elucidate hemodynamic mechanisms. (1) The PG varies as a function of axial position, with supraannular deployments yielding a maximum benefit of 7.85 mm Hg less than PGs for subannular deployments irrespective of commissural alignment (p < 0.01); (2) in contrast, LF decreased in relationship to subannular deployment; and (3) at peak systole, sinus flow shear stress increased with deployment depth as did sinus washout with and without coronary flow. First, supraannular axial deployment isassociated with lower PGs irrespective of commissuralalignment. Second, subannular deployment is associated with more favorable sinus hemodynamics and less LF. Further invivo studies are needed to substantiatethese observations and facilitateoptimalprosthesis positioning during ViV procedures.

A Burke–Schumann analysis of diffusion-flame structures supported by a burning droplet

A Burke–Schumann description of three different regimes of combustion of a fuel droplet in an oxidising atmosphere, namely the premixed-flame regime, the partial-burning regime and the diffusion-flame regime, is presented by treating the fuel and oxygen leakage fractions through the flame as known parameters. The analysis shows that the burning-rate constant, the flame-standoff ratio, and the flame temperature in these regimes can be obtained from the classical droplet-burning results by suitable definitions of an effective ambient oxygen mass fraction and an effective fuel concentration in the droplet interior. The results show that increasing oxygen leakage alone through the flame lowers both the droplet burning rate and the flame temperature, whereas leakage of fuel alone leaves the burning rate unaffected while reducing the flame temperature and moving the flame closer to the droplet surface. Solutions for the partial-burning regime are shown to exist only for a limited range of fuel and oxygen leakage fractions.

A spectral analysis of the domain decomposed Monte Carlo method for linear systems

The domain decomposed behavior of the adjoint Neumann-Ulam Monte Carlo method for solving linear systems is analyzed using the spectral properties of the linear operator. Relationships for the average length of the adjoint random walks, a measure of convergence speed and serial performance, are made with respect to the eigenvalues of the linear operator. In addition, relationships for the effective optical thickness of a domain in the decomposition are presented based on the spectral analysis and diffusion theory. Using the effective optical thickness, the Wigner rational approximation and the mean chord approximation are applied to estimate the leakage fraction of random walks from a domain in the decomposition as a measure of parallel performance and potential communication costs. The one-speed, two-dimensional neutron diffusion equation is used as a model problem in numerical experiments to test the models for symmetric operators with spectral qualities similar to light water reactor problems. In general, the derived approximations show good agreement with random walk lengths and leakage fractions computed by the numerical experiments.

Performance Evaluation of Various Rim-Seal Geometries

A numerical investigation has been performed to evaluate the performance of various rim seals in a gas turbine. Two performance functions of the rim seal related to sealing effectiveness and the loss coefficient of the main flow were analyzed for two rim-seal inlet velocities and three leakage fractions using three-dimensional Reynolds-averaged Navier–Stokes equations. The Spalart–Allmaras model was used as the turbulence closure model. The Reynolds number, based on the axial chord at the mainstream outlet, was fixed at 500,000. Computational results for the sealing effectiveness were validated by comparison to experimental data. To examine the effects of the rim-seal configurations on the sealing effectiveness and loss coefficient of the main flow, five different rim-seal geometries were tested. The results indicate that a newly designed rim seal, which includes the inner cavity attached to the rotor side and the narrow interaction plane between the mainstream and rim seal, shows the best performance in sealing effectiveness and loss coefficient among the five tested cases for most of the tested leakage fractions and rim-seal inlet velocities.

The Effects of a Parametric Variation of the Rim Seal Geometry on the Interaction Between Hub Leakage and Mainstream Flows in High Pressure Turbines

The objective of this work was to assess and understand the effects of a parametric variation performed on a typical overlapping rim seal geometry. The datum geometry has been the focus of a detailed experimental investigation employing a large-scale linear cascade subjected to a range of the mass flow rates and swirl velocities of the leakage air. The parametric variations described in this paper were examined using validated computational fluid dynamics (CFD). As a part of the parametric studies, both the axial and the radial seal clearance between the rotor fin (angel wing) and stator platform were varied as well as the length of the overlap between stator and rotor platforms. In addition, the effects of forward and backward facing annulus steps were also investigated. It has been found that a backward-facing annulus step was detrimental for all conditions considered, while a forward-facing step offered improvements for smaller step heights and/or lower leakage fractions. Tightening of the seal clearances closer to the annulus line improved the sealing effectiveness but often at the expense of increased losses. On the other hand, increasing the overlap length led to improvements in the sealing effectiveness with very small effects on the overall losses. Moving the rim seal away from the blade-leading edges reduced the pressure asymmetry at the rim seal and increased the flow uniformity of the leakage air. However, this led to an increased cross-passage flow (more negative skew) and higher losses at all but lowest leakage fractions. The results presented in this paper highlight the fact that there may not be an optimum rim seal solution that would offer an improvement for the full range of leakage fractions and that, for different rim sealing flows, there may be a different optimum geometry. In addition, rotor disk movements in radial and axial directions at various off-design conditions should be considered as a part of the design process. Based on the presented results, it may be of a benefit to the turbine designer to consider rotor disk designs that would be more biased towards the upstream and outward disk movements, which would result in tightening of the seal clearances and avoidance of a backward-facing annulus step.

Uptake of NOM fractions by anion-exchange resins in demineralization plants

The elimination of natural organic matter (NOM) is an important objective of water treatment in demineralization plants of power stations, because NOM is considered to be a corrosion risk factor in the steam water cycle. The aim of this study was to compare the performance of different anion-exchange resins (AERs) relating to their NOM fractions removal in demineralization treatment (input water with acidic pH after cation exchange). NOM removal was assessed using the dissolved organic carbon (DOC) measurement and the liquid chromatography–organic carbon detection (LC–OCD) method. At acidic pH, weak base AERs with their higher total volume capacities (TVCs) showed also higher NOM uptakes in comparison with strong base AERs. Further, the macroporous polystyrene weak base AER MP64 was found to be the most effective AER for the removal of problematic NOM leakage fractions (hydrophobic organic carbon (HOC), biopolymers, low-molecular-weight (LMW) neutrals) before the breakthrough point of the stronger adsorbed anions.

Evaluation of integral quantities in an accelerator driven system using different nuclear models implemented in the MCNPX Monte Carlo transport code

The MCNPX code offers options based on physics packages; the Bertini, ISABEL, INCL4 intra-nuclear models, and Dresner, ABLA evaporation–fission models and CEM2k cascade-exciton model. This study analyzes the main quantities determining ADS performance, such as neutron yield, neutron leakage spectra, heating and neutron and proton spectra in the target and in the beam window calculated by the MCNPX-2.5.0 Monte Carlo transport code, which is a combination of LAHET and MCNP codes. The results obtained by simulating different models cited above and implemented in MCNPX are compared with each other. The investigated system is composed of a natural lead cylindrical target and stainless steel (HT9) beam window. The target has been optimized to produce maximum number of neutrons with a radius of 20cm and 70cm of height. The target is bombarded with a high intensity linear accelerator by a 1GeV, 1mA proton beam. The protons are assumed uniformly distributed across the beam of radius 3cm, and entering the target through a hole of 5.3cm radius. The proton beam has an outer radius of 5.3cm and an inner radius of 5.0cm. The maximum value of the neutron flux in the target is observed on the axis ∼10cm below the beam window, where the maximum difference between 7 different models is ∼15%. The total neutron leakage of the target calculated with the Bertini/ABLA is 1.83×1017n/s, and is about 14% higher than the value calculated by the INCL4/Dresner (1.60×1017n/s). Bertini/ABLA calculates top, bottom and side neutron leakage fractions as 20%, 2.3%, 77.6% of the total leakage, respectively, whereas, the calculated fractions are 18.6%, 2.3%, 79.4%, respectively, with INCL4/Dresner combination. The largest heat deposition density by considering all particles in the beam window calculated with CEM2k model is 104W/cm3/mA, which is 9.0% greater than the lowest value predicted with INCL4/Dresner model (95.4W/cm3/mA). The maximum average heat deposition density for all particles in the target is calculated as 6.87W/cm3/mA with INCL4/ABLA.

Comparisons of the Calculations Using Different Codes Implemented in MCNPX Monte Carlo Transport Code for Accelerator Driven System Target

The MCNPX code offers options based on physics packages; the Bertini, ISABEL, INCL4 intra-nuclear models, and Dresner, ABLA evaporation-fission models and CEM2k cascade-exciton model. The study analyzes the main quantities determining ADS performance, such as neutron yield, neutron leakage spectra, and neutron and proton spectrain the target andin the beam window calculated by the MCNPX-2.5.0 Monte Carlo transport code, which is a combination of LAHET and MCNP codes. The results obtained by simulating different models, cited above and implemented in MCNPX are compared with each other.The investigated system is composed of a natural lead cylindrical target and stainless steel (HT9) beam window. Target has been optimized to produce maximum number of neutrons with a radius of 20 cm and 70 cm of height. Target is bombarded with a high intensity linear accelerator by a 1 GeV, 1 mA proton beam. The protons are assumed uniformly distributed across the beam of radius 3 cm, and entering the target through a hole of 5.3 cm radius. The proton beam has an outer radius of 5.3 cm and an inner radius 5.0 cm. The maximum of the neutron flux in the target is observed on the axis ~ 10 cm below the beam window, where the maximum difference between 7 different models is ~ 15 %. The total neutron leakage out of the of the target calculated with the Bertini/ABLA is 1.83×1017 n/s, and is about 14 % higher than the value calculated by the INCL4/Dresner (1.60×1017 n/s). Bertini/ABLA calculates top, bottom and side neutron leakage fractions as 20 %, 2.3 %, 77.6 % of the total leakage, respectively, whereas, they become 18.6 %, 2.3 %, 79.4 % with INCL4/Dresner combination.

Operational characteristics of residential and light-commercial air-conditioning systems in a hot and humid climate zone

Forced-air space-conditioning systems are ubiquitous in U.S. residential and light-commercial buildings, yet gaps exist in our knowledge of how they operate in real environments. This investigation strengthens the knowledge base of smaller air-conditioning systems by characterizing a variety of operational characteristics measured in 17 existing residential and light-commercial air-conditioning systems operating in the cooling mode in Austin, Texas. Some key findings include: measured airflow rates were outside of the range recommended by most manufacturers for almost every system; actual measured cooling capacities were less than two-thirds of rated cooling capacities on average; hourly fractional operation times increased approximately 6% for every °C increase in indoor–outdoor temperature difference; and lower mean indoor surrogate thermostat settings and higher supply duct leakage fractions were most associated with longer operation times. The operational characteristics and parameters detailed herein provide insight into the magnitude of the effects of HVAC systems on both energy consumption and indoor air quality (IAQ) in residential and light-commercial buildings.

Intermediate Respiratory Intensive Care Units: Definitions and Characteristics

This study aims at assessing the global dynamic behavior, elastic deformability, closing energy and turbulence of rigid versus deformable stented (RS vs DS) valve systems with deformable and rigid textile materials (DT vs RT) through studying the stent-valve interaction compared to a bioprosthetic material in transcatheter aortic valves (TAV).Three 19 mm stented textile TAV designs (RS-DT, RS-RT and DS-RT) with different stent and leaflet properties were tested and compared with a control bioprosthetic TAV (RS-DB) in a left heart simulator flow loop under physiological pressure and flow. Particle Image Velocimetry and high speed imaging were performed. Pressure gradients (PG), leakage fractions (LF), Pinwheeling indices (PI), closing energy (E) and Reynolds shear stresses (RSS) were calculated.(a) PGs and LFs were 11.86 ± 0.51 mmHg, 11.70 ± 0.34%; 8.84 ± 0.40 mmHg, 29.80 ± 0.76%; 11.59 ± 0.12 mmHg, 14.23 ± 1.64%; and 7.05 ± 0.09 mmHg, 12.08 ± 0.45% % for RS-DB, RS-DT, RS-RT and DS-RT respectively. (b) PIs were 15.79 ± 2.34%, 4.36 ± 0.84%, 2.47 ± 0.51% and 2.03 ± 0.33% for RS-DB, RS-DT, RS-RT and DS-RT respectively. (c) E is lowest for DS-RT (0.0010 ± 0.0002 J) followed by RS-RT (0.0017 ± 0.0002 J), RS-DB (0.0023 ± 0.0004 J) and highest with RS-DT (0.0036 ± 0.0007 J). (d) At peak systole lowest RSS was obtained with RS-DT (87.82 ± 0.58 Pa) and highest with DS-RT (122.98 ± 1.87 Pa).PGs, LFs, PIs and E were improved with DS-RT compared to other textile TAVs and RS-DB. Despite achieving more RSS than the rest of TAVs, DS-RT still falls within the same range of RSS produced by the other 2 valves and control exceeding the threshold for platelet activation.