Variation Of Layer Thickness Research Articles

Impact of insulating layer thickness variation on Igzo-based thin-film transistor performance

Abstract This paper highlights the thin film transistors used in the latest applications and devices. The working principle of thin film transistors with various device structures can be used to fabricate thin film transistors. Progress in the latest materials that are being used in applications like LCDs, sensors, RFID tags, Displays, etc. The remarkable characteristics of Indium-Gallium-Zinc Oxide (IGZO) thin films, for instance, their transparency and high mobility, have generated significant interest in the application part of Thin-Film Transistors (TFTs). Simulating the functioning of a-IGZO TFTs over Silvaco [Atlas] TCAD Tool, four distinct insulators [SiO2, Si3N4, HfO2, and Al2O3] are taken into consideration by adjusting insulator thicknesses and measuring the overall current density.

Exploring the effect of layer thickness on the elastoplastic properties of the constituent materials of CrN/CrAlN multilayer coatings: a nanoindentation and finite element-based investigation

This paper aims to assess the effect of layer thickness on the elastoplastic properties of the constituent materials of multilayer coating systems, as well as on the stress and strain fields in the vicinity of the coating/substrate interface. A methodology based on a trust-region reflective optimization algorithm, integrated with finite element analysis of the nanoindentation process, is employed to extract the elastoplastic properties of the distinct layers, constituting multilayer coating. This approach is validated on a CrN/CrAlN multilayer coating systems with varying layer thicknesses from 1 to 0.35 µm, by which Young's modulus (E), yield stress (σy), and work hardening exponent (n) of each individual coating material layer were obtained. The results revealed a reduction in the hardness and Young's modulus of either CrN, or CrAlN coating layer as the layer thickness decreased. Finite element analysis of the nanoindentation process demonstrated that decreasing the coating layer thickness leads to an increase in the plastic deformation within the coatings, which reduces the stress concentration in this area. The simulation results suggest that an optimum thickness of 0.5 μm of CrAlN and CrN monolayer materials would improve the adhesion properties of CrN/CrAlN multilayer coatings.

Wall-mounted circular cylinder flows

The flow over wall-mounted circular cylinders is influenced by variations in aspect ratio, Reynolds number, and boundary layer thickness, all of which affect the vortical structures in the wake. In this study, we conducted direct numerical simulations and data-driven techniques, including proper orthogonal decomposition (POD) and dynamic mode decomposition, to examine vortical flows behind wall-mounted circular cylinders with aspect ratios of 4, 8, and 12 at Reynolds numbers ranging from 60 to 800, based on cylinder diameter. The incoming boundary layer thickness varied from 0.05 to 0.25. Our findings reveal that a thicker boundary layer promotes the development of low-frequency symmetric vortical structures along the wall surface, suppressing antisymmetric wake shedding. Consequently, the induced upwashing motion of the flow behind the cylinder pushes the wake shedding region closer to the free-end side, facilitating quadrupole mean streamwise vortices. The wake shedding frequency is significantly altered as the symmetric low-frequency mode intensifies along the boundary. POD analysis demonstrates the coexistence of symmetric and antisymmetric vortical structures in the wake region. The presence of either antisymmetric or symmetric wake shedding is determined by the dominant frequency in the instantaneous flow. These findings substantiate previous conjectures about the simultaneous presence of symmetric and antisymmetric wake shedding modes and enhance our understanding of vortical flows around wall-mounted circular cylinders.

Impact of Summer Air Temperature on Water and Solute Transport on a Permafrost‐Affected Slope in West Greenland

AbstractIn Arctic landscapes, the active layer forms a near‐surface aquifer on top of the permafrost where water and nutrients are available for plants or subject to downslope transport. Warmer summer air temperatures can increase the thickness of the active layer and alter the partitioning of water into evapotranspiration and discharge by increasing the potential evapotranspiration, the depth to the water table, and changing the flow paths but the interacting processes are poorly understood. In this study, a numerical model for surface‐ and subsurface cryo‐hydrology is calibrated based on field observations from a discontinue permafrost area in West Greenland considered sensitive to future climate changes. The validated model is used to simulate the effect of three summers with contrasting temperature regimes to quantify the variations in the active layer thickness, the resulting changes in the water balance, and the implications on solute transport. We find that an increase of summer air temperature by1.6°C, under similar precipitation can increase the active layer thickness by 0.25 m, increase evapotranspiration by 5%, and reduce the total discharge compared to a colder summer by 9%. Differences in soil moisture and evapotranspiration between upslope and downslope were amplified in a warm summer. These hydrological differences impact solute transport which is 1.6 times faster in a cold summer. Surprisingly, we note that future warmer summer with increase in permafrost thaw may not necessary lead to an increase in discharge along a hill slope with underlying permafrost.

Topology transition description of horseshoe vortex system in juncture flows with velocity characteristic lines

Particle image velocimetry and numerical simulation results of juncture flows were analyzed to parametrically investigate topology transition. The vortex system evolutions from non-vortex to multi-vortex with variations in obstacle bluntness, obstacle width, flow velocity and boundary layer thickness are discussed from the perspective of velocity characteristic lines. The velocity characteristic lines of u=0, v=0, and ∇2v=0 are adopted to describe the vortex system evolution. The motions of the characteristic lines with juncture flow parameters are described in detail, and the corresponding reflections of the vortex system patterns are illustrated. A panoramic picture of the development of velocity characteristic lines corresponding to the HSV topology transition from a non-vortex to a multi-vortex system with variations in the juncture flow parameter is established. Two methods for determining the attachment/separation pattern of the most upstream singularity are proposed. One method is based on the number of intersections of the u=0 and v=0 velocity characteristic curve lines, and the other is based on the relative positions of the most upstream feet of the u=0 and v=0 loop curves with both feet attached to the wall.

In vitro assessment of corrosion, antibacterial properties, and degradation behavior of zirconia-coated polyetheretherketone (PEEK)

The medical industry often uses ceramic and polymeric coatings to safeguard metal substrates. However, more investigation is required to explore the implementation of ceramic coatings on polymer substrates and to determine their degradation and in vitro characteristics. This work involves applying zirconia coating onto the 3D-printed PEEK polymer substrate using the RF magnetron sputtering technique. With varying layer thickness and printing speed parameters, PEEK samples (S1, S2, S3, and S4) were 3D printed and coated with zirconia. The coated and uncoated samples were immersed in Fusayama artificial saliva solution for 30 days. Following immersion in artificial saliva, this study examined the corrosion of 3D-printed PEEK samples with and without coatings. Elemental mapping, field emission scanning electron microscopy, and X-ray photoelectron spectroscopy were employed to evaluate sample morphology and estimate the binding energy of possible compounds generated in the artificial saliva solution. In vitro assessments such as antibacterial studies were performed against E. coli and S. aureus, and cytotoxic analysis was performed using Human Wharton’s jelly-derived mesenchymal stem cells (WJ-MSCs) to determine cell proliferation. The results indicated that sample S3, printed with 0.15 mm layer thickness and 20 mm/s print speed coated with zirconia showed a better degradation rate of 9.01% whereas the other three samples S1, S2, and S4 coated with zirconia showed deterioration rates of 36.4%, 33% and 16% respectively. Sample S3 showed a better antibacterial activity as biofilm formation was absent and also showed cell viability of about 79% and hence can be considered as a viable option for dental applications.

The Influence of Thickness and Spectral Properties of Green Color-Emitting Polymer Thin Films on Their Implementation in Wearable PLED Applications.

A systematic investigation of optical, electrochemical, photophysical, and electrooptical properties of printable green color-emitting polymer (poly(9,9-dioctylfluorene-alt-bithiophene)) (F8T2) and spiro-copolymer (SPG-01T) was conducted to explore their potentiality as an emissive layer for wearable polymer light-emitting diode (PLED) applications. We compared the two photoactive polymers in terms of their spectral characteristics and color purity, as these are the most critical factors for wearable lighting sources and optical sensors. Low-cost, solution-based methods and facile architecture were applied to produce rigid and flexible light-emitting devices with high luminance efficiencies. Emission bandwidths, color coordinates, operational characteristics, and luminance were also derived to evaluate the device's stability. The tuning of emission's spectral features by layer thickness variation was realized and was correlated with the interplay between H-aggregates and J-aggregates formations for both conjugated polymers. Finally, we applied the functional green light-emitting PLED devices based on the two studied materials for the detection of Rhodamine 6G. It was determined that the optical detection of the R6G photoluminescence is heavily influenced by the emission spectrum characteristics of the PLED and changes in the thickness of the active layer.

The acoustic properties of FDM printed wood/PLA-based composites

The acoustic properties of the Fused Deposition Modelling (FDM) printed PLA wood composite was investigated. Initially tensile and flexural of wood PLA composite was studied with respect to varying layer thickness (0.15 mm, 0.20 mm, and 0.30 mm), infill density (30 %, 60 %, and 90 %), and pattern (Layer, Triangle, and Hexagon). The outcomes demonstrated that the specimen produced with a hexagonal pattern, 90% infill density, and 0.2 mm layer thickness had the highest tensile (16 MPa) and flexural strength (16 MPa). Utilizing this optimized parameter, micro-perforated panels were printed and acoustic properties were studied. Five specimens with a 3 mm thickness, various perforation diameters (5 mm, 4 mm, and 3 mm), and architecturally tapered perforations were fabricated. Using the impedance tube approach, the sound transmission loss and sound absorption coefficients were measured. The findings indicate that, in comparison to all the printed specimens, tapered type perforation with an exterior diameter of 5 mm and an internal diameter of 4.7 mm showed highest sound absorption coefficient of 0.60 Hz. A viscous loss is obtained by its convergent hole diameter reduction, which results in sound attenuations and is easily absorbed in the micro-perforated panel. Similar to this, the specimen printed with smaller perforation diameters (3 mm) had a high sound transmission loss of 79 dB. The small diameter of the perforations prevented the passage of sound waves. The current study is anticipated to lay the groundwork for extensive future research on these classes of materials, potentially serving as a catalyst for advancements in FDM based polymeric materials research and development.

Epitaxial growth of quasi-2D van der Waals ferromagnets on crystalline substrates

Intrinsic magnetism in van der Waals materials has instigated interest in exploring magnetism in the 2D limit for potential applications in spintronics and also in understanding novel control of 2D magnetism via variation of layer thickness, gate tunability and magnetoelectric effects. The chromium telluride (CrxTey) family is an interesting subsection of ferromagnetic materials with highTCvalues, also presenting diverse stoichiometry arising from self-intercalation of Cr. Apart from the layered CrTe2system, the other non-layered CrxTeycompounds also offer exceptional magnetic properties, and a novel growth technique to grow thin films of these non-layered compounds offers exciting possibilities for ultra-thin spin-based electronics and magnetic sensors. In this work, we discuss the role of crystalline substrates in chemical vapor deposition growth of non-layered 2D ferromagnets, where the crystal symmetry of the substrate as well as the misfit and strain are the key players governing the growth mechanism of ultra-thin Cr5Te8, a non-layered ferromagnet. The magnetic studies of the as-grown Cr5Te8reveal the signatures of co-existing soft and hard ferromagnetic phases, which makes this system an intriguing system to search for emergent topological phases, such as magnetic skyrmions.

Counterbalancing effects of bowing in gallium nitride templates by epitaxial growth on pre-strained sapphire substrates

To minimize bowing in a gallium nitride (GaN) template, which is caused by differences in the properties of the GaN film and the sapphire substrate, we studied how to offset bowing by directly growing GaN using the hydride vapor phase epitaxy (HVPE) method on the frontside of a pre-strained sapphire substrate prepared using a backside grinding process. The relationships between the respective thicknesses and stresses of the undamaged sapphire, damaged sapphire, and GaN layers were analyzed by deriving the bow formula, which is a modification of Freund's equation, and the theoretical formula-derived results were compared with experimentally determined values. The bow of the GaN template was measured using a micrometer, and the residual stresses in the GaN and sapphire, carrier mobilities, and GaN crystal qualities were measured using a micro-Raman spectrophotometer. The results confirmed the annealing effect on the damaged sapphire layer, and the introduction of pre-strained GaN templates facilitated easier bow control compared to that afforded by a conventional GaN template. Additionally, we identified trends and optimal conditions for changes in residual stress, carrier mobility, and crystal quality in GaN and the damaged sapphire layer based on layer thickness and stress variations. We explain the mechanisms responsible for changes in bow, stress, carrier mobility, and crystal quality of the GaN template.

Structural detachment influences the shale gas preservation in the Wufeng-Longmaxi Formation, Northern Guizhou Province

Abstract In order to reveal the restriction in shale gas enrichment of the Wufeng-Longmaxi Formation in the northern Guizhou province, the influence model of detachment layer was established through field geological investigation, core observation, logging, sample analysis, and geological background data. The response relationship between the detachment layer and the shale gas enrichment model in different structural formats was analyzed. The results show that the thickness of the Wufeng-Longmaxi Formation’s detachment layer is influenced by the conditions near the fault zones and mineralogical characteristics. The lithofacies of the detachment layer shows mainly a combination of clay-rich shale facies. This indicates that lithofacies type is one of the main factors influencing the variation in slip layer thickness. The detachment layer exhibits distinct well logging response characteristics and is influenced by nitrogen enrichment. The development of detachment fractures allows atmospheric nitrogen to infiltrate shale gas. It leads to poor gas saturation in the shale gas. In addition, the overall tectonic deformation in the northern Guizhou province was found to gradually intensify from Northwest to Southeast, and there were two tectonic models: a slot-shift tape transition belt and a spacer type deformation belt. The influence of decollements on shale gas preservation was barely found in the northern Guizhou province. It is mainly controlled by buried depth of the target layer, conditions of the cover layer, structural type, and deformation intensity.

Soil Carbon and Nitrogen Stocks Across Hillslopes Underlain by Continuous Permafrost in the Northern Arctic Foothills, Alaska, United States

ABSTRACTConstraining the variability of soil organic carbon (SOC) and total nitrogen (TN) stocks across hillslopes in Low Arctic permafrost‐affected landscapes remains a significant challenge for improving global estimates of permafrost SOC stocks. We investigated SOC and TN stocks across hillslopes at two sites in the Arctic Foothills of Alaska, United States (Happy Valley and Sagwon Hills). Average SOC and TN stocks for the 0–1‐m depth interval were high (52.0 ± 15.1 kg C m−2 and 2.74 ± 0.82 kg N m−2) and linearly related (R2 = 0.74, p < 0.0001). Unlike soils of other permafrost and nonpermafrost landscapes, variability was greatest within rather than between hillslope positions. Furthermore, SOC and TN stocks in the surface 1 m did not exhibit strong patterns by hillslope position and were only weakly associated with major geomorphic parameters that typically predict SOC and TN stocks well in other landscapes. Although sampling at upper hillslope positions was largely limited to depths of less than 1.5 m due to the presence of coarse fragments in reworked glacial till, deeper observations at lower hillslope positions (footslopes, toeslopes, and basins) revealed significantly larger SOC stocks (92.0 ± 18.0 kg C m−2 at 2 m; 117.1 ± 10.4 kg C m−2 at 3 m). The unique small‐scale variability in ice content, cryoturbation, patterned ground, and organic layer thickness on these broad, Low Arctic sites contributes to the relatively homogeneous distribution of SOC and TN stocks across hillslope positions in the top 1 m, but a future focus on deeper sampling may reveal greater differences in SOC and TN stocks.

Slicing on the Tessellated Model for the 3D Printing Process based on the Variable Thickness Layers

Additive Manufacturing (AM) is a modern technology that enhances manufacturing by building thin layers of material from digitized (3D) designs, entirely constructed using advanced CAD software. This method facilitates the creation of new types of objects with unique material properties. However, while AM is often hailed as the next industrial revolution, significant challenges remain for its successful commercialization. This project focuses on the microstructural aspects and the dimensional accuracy of the product. Additionally, the paper discusses the slicing algorithm and the material extrusion process in detail.

A novel framework of the lattice Boltzmann model for multilayer shallow water systems

This study proposes a novel framework of the lattice Boltzmann model for multilayer shallow water equations, considering the mass and momentum exchanges between layers (LABMSWE+). Compared with the original LABMSWE model consisting of N two-dimensional lattice Boltzmann method for shallow water equation (LABSWE) models, the new model includes 1+N LABSWE models. The singular LABSWE model with unit relaxation time is introduced to update the total water depth, and thus, the layer water depths can be obtained explicitly through the fixed layer ratios. The N-layer LABSWE models with the multiple-relaxation-time operator evolve the layer velocities. These two modules are coupled by the total water depth and depth-averaged velocities. The constructed model avoids the freely variable layer thicknesses, which is considered as the main source of the instability. In addition, the mass exchanges enable this model to simulate vertical circulation flows, which are beyond the application of the LABMSWE model. Several numerical tests are then conducted to validate the proposed model. The results show that it exactly satisfies the C-property. In addition, the central difference scheme is more stable and accurate than the upwind and nonequilibrium schemes in the computing of the mass exchanges. The numerical results have an excellent agreement with analytical solutions and reference data, while some unstable and nonphysical results are obtained by the original LABMSWE model. Moreover, the computational time is about 40%–60% of that for the MIKE3, a finite volume solver for the three-dimensional shallow water equations by the Danish Hydraulic Institute.

Performance optimization of eco-friendly CH3NH3SnI3 based perovskite solar cell employing CH3NH3SnBr3 as hole transport layer by SCAPS-1D device simulator

This study focuses on the theoretical aspects of third-generation perovskite solar cells (PSC), with the aim of replacing traditional silicon-based counterparts. With potential for higher efficiency and low manufacturing costs, perovskite cells offer unique crystallographic structures allowing adjustments to photoluminescence wavelength. This research addresses challenges in cost-effective solar spectrum utilization and optimization of parameters, device architecture, and materials for high-efficiency cells. In this study, we simulated a perovskite-based solar cell (CH3NH3SnI3) using solar cell capacitance simulator-one dimension simulator under AM 1.5G illumination. The chosen electron transport layer is TiO2, and hole transport layer is CH3NH3SnBr3. The simulation explores variations in layer thickness, defect concentration, interface defects, doping concentration and electron affinity. Additionally, we analyzed the impact of back metal contact work function and temperature variations. Results indicate optimal absorber layer thickness at 0.5µm. Reduced defect concentrations, increased doping concentration and a higher work function for the back contact, enhance efficiency of PSC. The initial parameters yielded a 19.79% efficiency based on base values before optimization, which increased to 26.66% after optimization. According to the latest NREL data, the highest reported efficiency for PSC is 26.1%. This research provides insights into perovskite-based solar cell design for enhanced efficiency.

Ultrasound-based histological differences in thickness between puffy eyelids and normal eyelids in Asian monolid women

BackgroundUpper eyelid tissue swelling is a common characteristic among Asian monolid individuals and is associated with a high incidence of complications following eyelid surgery. Currently, there is no precise definition for upper eyelid tissue swelling, necessitating further research to elucidate the specific causes contributing to upper eyelid puffiness. MethodBetween June 2023 and February 2024, we recruited 84 Asian monolid women categorized into groups based on the severity of upper eyelid tissue swelling: the puffy eyelid group and the normal eyelid group. High-frequency ultrasound was employed to capture images of the upper eyelids and measure the thickness of various tissue layers. This study aims to conduct a comparative analysis to identify the factors contributing to upper eyelid fullness, focusing on elucidating the underlying causes of this condition. ResultAll volunteers underwent bilateral upper eyelid ultrasound imaging. Significant differences were observed in the thickness of subcutaneous fat, pre-tarsal fat, retro-orbicularis oculi fat（ROOF）, and composite fat(ROOF and pre-aponeurotic fat) layer between the puffy eyelid group and the normal eyelid group. However, no significant differences were found in skin thickness or orbicularis oculi muscle thickness. Additionally, no significant differences were observed in the thickness of various layers of the upper eyelid tissue between the left and right eyes in all participants. ConclusionThickening of the upper eyelid fat layer is a primary cause of upper eyelid puffiness. In upper blepharoplasty, targeted removal of pre-aponeurotic fat, ROOF, and pre-tarsal fat can achieve precise reduction to correct upper eyelid puffiness effectively.

Exploring the impact of epoxy coated 3D-Printed polymers on surface roughness and mechanical behavior: An experimental and numerical study

The present study used polymers such as PLA and ABS filaments for the 3D printing parts with varying layer thicknesses. The mechanical properties and surface finish of the as-printed and epoxy resin-coated samples were investigated. Noteworthy findings indicate that when the PLA material is printed at a layer thickness of 0.06 mm followed by no coating one can achieve superior tensile strength of approximately 39 MPa as compared to 20 MPa of ABS material. The ultimate tensile strength of the coated materials averaged approximately 15 MPa for both PLA and ABS. The surface roughness of PLA material printed with a 0.06 mm layer thickness showed a 95.13 % reduction after coating. Despite ABS samples being harder than PLA material, the layer thickness emerged as the most influential factor in enhancing the hardness. The dominance of lower layer thickness over other conditions is particularly evident in the modulus of elasticity. In addition to the experimental investigation, a non-linear structural analysis of the uniaxial tensile behaviour of the coated and uncoated 3D prints was also carried out. The fracture modes and deformation behaviours in numerical modelling and experimental results across various parametric conditions were found to be in good agreement. Specifically, the numerical results at lower loading conditions for a layer thickness of 0.06 mm PLA and ABS samples, in the uncoated conditions, mirrored the experimental outcomes.

Highly Luminescent Manganese‐Doped 2D Hybrid Perovskite Nanoplatelets with Dual Emissions Controlled Through Layer Thickness Modulation

AbstractDoping semiconductor nanomaterials with manganese ion (Mn2+) introduce a well‐defined photoactive d‐d level within the band structure, paving the way for diverse applications. Although Mn doping in single‐layer 2D hybrid perovskites (n = 1) has been extensively studied, limited research has been conducted on doping with modulation of the layer thickness. Herein, Mn2+ doping in hybrid 2D perovskite nanoplatelets (NPLs), L2An‐1[Pb1‐xMnx]nBr3n+1 (where L = butylammonium, A = methylammonium), with variations in Mn concentration (x = 0–0.60) and layer thickness (n = 1–3) is reported. Substitutional doping of Mn significantly increases the photoluminescence quantum yield as well as the rate of energy transfer efficiency, which strongly depends on the layer thickness of NPLs. The Mn concentration in 2D NPLs determines the rate of forward and backward energy transfer. Low‐temperature emission spectra allow to determine thickness‐dependent exciton binding energy for Mn‐doped 2D NPLs (x = 0.5) with values of 410 ± 11 meV (n = 1), 188 ± 9 meV (n = 2), and 151 ± 17 meV (n = 3). The faster dissociation of band‐edge excitons into free carriers at Mn2+ sites results in high brightness with an excellent CRI of 89.2 for the white light‐emitting diode.

Enhancing Blue Polymer Light-Emitting Diode Performance by Optimizing the Layer Thickness and the Insertion of a Hole-Transporting Layer.

Polymer light-emitting diodes (PLEDs) hold immense promise for energy-efficient lighting and full-color display technologies. In particular, blue PLEDs play a pivotal role in achieving color balance and reducing energy consumption. The optimization of layer thickness in these devices is critical for enhancing their efficiency. PLED layer thickness control impacts exciton recombination probability, charge transport efficiency, and optical resonance, influencing light emission properties. However, experimental variations in layer thickness are complex and costly. This study employed simulations to explore the impact of layer thickness variations on the optical and electrical properties of blue light-emitting diodes. Comparing the simulation results with experimental data achieves valuable insights for optimizing the device's performance. Our findings revealed that controlling the insertion of a layer that works as a hole-transporting and electron-blocking layer (EBL) could greatly enhance the performance of PLEDs. In addition, changing the active layer thickness could optimize device performance. The obtained results in this work contribute to the development of advanced PLED technology and organic light-emitting diodes (OLEDs).

The surface deformation of permafrost and active layer thickness in the upper reaches of the Black River basin, revealed by InSAR observations and independent component analysis

The Heihe River Basin, located in the northeastern part of the Qinghai-Tibetan Plateau, is part of the perennial permafrost belt of the Qilian Mountains. Recent observations indicate ongoing permafrost degradation in this region. This study utilizes data from 255 observations provided by Sentinel-1 satellites, MODIS Land Surface Temperature, SMAP-L4 soil moisture data, GNSS measurements, and in situ measurement. We introduced Variational Bayesian independent Component Analysis (VB-ICA) in multi-temporal Interferometric Synthetic Aperture Radar (MT-InSAR) processing to investigate the spatial-temporal characteristics of surface deformation and permafrost active layer thickness (ALT) variations. The analysis demonstrates strong agreement with borehole data and offers improvements over traditional methodologies. The maximum value of ALT in the basin is found to be 5.7 m. VB-ICA effectively delineates seasonal deformations related to the freeze-thaw cycles, with a peak seasonal deformation amplitude of 60 mm. Moreover, the seasonal permafrost's lower boundary reaches an elevation of 3700 m, revealing that permafrost is experiencing widespread degradation and associated soil erosion in the high elevation region of The Heihe River Basin. The paper also explores the efficacy of reference point selection and baseline network establishment for employing the InSAR method in monitoring freeze-thaw deformations. The study underscores the InSAR method's adaptability and its importance for interpreting permafrost deformation and related parameters.