Latent Heat Research Articles

Melting of PCM-graphite foam composites with contact thermal resistance: Pore-scale simulation

Latent heat energy storage systems have emerged as a solution to intermittency and instability in renewable energy sources, the phase transition of phase change materials (PCMs) within these systems is hindered by their poor thermal conductivity. Graphite foam, renowned for its superior thermal properties, stands as an ideal choice to improve the melting efficiency of PCMs. In the current study, the melting behavior of PCM-graphite foam composites is simulated by the pore-scale numerical simulation (PNS) by employing cubic idealized cells with spherical pores and cylindrical channels. The computed results demonstrate that the porosity and contact thermal resistance of graphite foam are key factors affecting the melting efficiency of PCMs. The full melting time (FMT) of PCMs increases with porosity, achieving a 53.1 % improvement as porosity decreases from 0.90 to 0.75. In addition, the absence of natural convection markedly diminishes the maximum melting rate of PCM, reducing it by 33.5 % to 50.3 % for porosity from 0.75 to 0.90. Notably, it needs to be emphasized that the melting rate of PCM is significantly reduced when the contact thermal resistance surpasses 1.0 × 10–4 m2·K·W−1. Compared to the idealized condition without contact thermal resistance, the dimensionless FMTs for porosities of 0.75, 0.80, 0.85, and 0.90 extend by 27.3 %, 27.1 %, 22.2 % and 23.9 % for a contact thermal resistance of 5.0 × 10–4 m2·K·W−1, respectively.

Phase-Change/Salt-Based Slow-Release Composite Material for Anti-Icing and Snow-Melting

Currently, self-desiccating asphalt mixtures on roads mainly incorporate phase-change materials or salt-based slow-release agents individually for de-icing. However, pure phase-change material mixtures have limited anti-freezing efficiency and short heat-release duration, making them impractical for large-scale snow melting; meanwhile, salt-based slow-release agents suffer from rapid deterioration in de-icing performance. To address these issues encountered, herein, we introduce the phase-change/salt-based slow-release composite materials via the integration of these two materials and investigate their pavement and de-icing performance with the asphalt mixture. For the pavement performance, the optimal asphalt–aggregate ratio for the anti-icing asphalt mixture was found to be 5.1% For anti-bonding and de-icing performance, the electrical conductivity tests, bonding pull-off tests, and interfacial contact melting experiments were conducted. The results indicate that the latent heat of the TH-ME5 (phase-change material) can delay the decrease in environmental temperature and inhibit salt release from T-SEN (salt-based slow-release material), thereby extending the lifespan of the anti-icing asphalt mixture. These results demonstrate that the synergistic effect between the two components of the composite material not only enhance the snow-melting and de-icing performance of the asphalt pavement but also prolong the snow-melting time of the pavement in a low-temperature environment.

Analysis on the effect of novel topological optimization fin structures considering eccentricity on the heat storage and release characteristics of shell and tube phase change heat accumulator

Shell and tube phase change accumulator (STPCA), as a common type of heat accumulator, can effectively solve the mismatching of time and space in solar thermal power generation by using phase change storage technology. However, the low thermal conductivity of phase change materials (PCMs) reduces its heat storage and release rate. To achieve a rapid latent heat energy storage and release, it needs to carefully modify the structure of STPCA. In the existing literature, insufficient attention has been given to simultaneously addressing the heat storage and release processes, while there is a scarcity of topological optimization methods employed in fin design. On one hand, it is difficult to find the optimal structure. On the other hand, the optimized structure is suitable for melting process but may not be suitable for solidification process. In this contribution, we initially integrated topological optimization and eccentricity to derive fin structures suitable for respective melting and solidification processes. Then, we compared and analyzed the effects of eccentricity and objective function on melting and solidification processes. Finally, we summarized the topology optimization process, objective function and eccentricity suitable for fast heat storage and release. The findings indicated that as the eccentricity increases, the rate of heat storage and release initially rises before subsequently declining. In this work, it is found that an eccentricity of 5 mm is the best. From the whole heat storage and release cycle, when the eccentricity is 5 mm, the objective function is the minimum temperature difference and the topological optimization fin structure calculated during solidification process shows the best heat storage and release performance. Compared with the topology optimization structure without eccentricity, the heat storage speed is increased by 36.43 %, and the heat release speed is increased by 15.53 %. The design law of the STPCA based on combined with the eccentricity influence and topology optimization method is summarized to help improve its heat storage and release performance.

Silica-based aerogels encapsulate organic/inorganic composite phase change materials for building thermal management

Phase change energy storage materials are widely used in thermal management because they reduce energy consumption and effectively address issues such as energy supply and demand mismatches. However, challenges such as leakage in solid-liquid phase change materials (PCMs), flammability in organic solid-liquid PCMs, and supercooling and phase separation in inorganic solid-liquid PCMs still need to be resolved for their practical applications. In this study, we used methyl palmitate, dodecahydrate disodium hydrogen phosphate, and decahydrate sodium carbonate as the main PCMs, sodium carboxymethyl cellulose as an emulsifier and thickener, and silica aerogel as the encapsulating material to successfully prepare a novel shape-stabilized organic/inorganic composite PCM (CPCM). The prepared CPCM exhibits excellent shape stability and flame retardancy without supercooling or phase separation issues. In addition, the prepared CPCM has a high latent heat value (174.1 J/g) and a suitable phase transition temperature (22.9 °C), and its thermal performance remains basically unchanged after 100 heating/cooling cycles. Furthermore, this CPCM also demonstrates exceptional performance in building thermal management. This study provides a new solution to the problems of flammability, supercooling, phase separation and easy leakage of CPCM currently used in the field of building thermal management.

Cold energy storage enhancement and phase transition temperature regulation

The objective of this study is to prepare a highly adjustable ester phase change material (PCM) and further optimize its cold storage properties using a simple and controllable physical method. Initially, lauric acid (LA) and polyethylene glycol 200 (PEG 200) are selected as raw materials, and a non-toxic and environmentally friendly polyethylene glycol laurate (PLE) with a tiny supercooling is prepared under the condition of acid-alcohol molar ratio of 1:3. To further regulate the cold storage property of PLE, a series of PCMs with different melting temperatures are successfully prepared using PLE blended with ethanol (EA). Among them, the lowest melting temperature in the study reaches −15.2 °C, which is about 94.6 % lower compared to −7.81 °C for PLE, and the highest latent heat of melting is 81.56 J/g. It is also observed that the supercooling of a range of samples is also optimized compared to the PLE, with a maximum reduction of 27.1 %. Additionally, the prepared samples not only exhibit excellent stability but also demonstrate outstanding application potential in temperature control and preservation experiments. This innovative achievement provides a richer selection of PCMs for the cold storage field. More crucially, this is the first report utilizing EA to regulate the temperature range of ester-based PCMs. This method is simple, easy to operate, and highly reproducible. It paves the way for the refinement, diversification, and customization of refrigeration technology.

Intrinsically Flexible Phase Change Fibers for Intelligent Thermal Regulation.

Owing to the significant latent heat generated at constant temperatures, phase change fibers (PCFs) have recently received much attention in the field of wearable thermal management. However, the phase change materials involved in the existing PCFs still experience a solid-liquid transition process, severely restricting their practicality as wearable thermal management materials. Herein, we, for the first time, developed intrinsically flexible PCFs (polyethylene glycol/4,4'-methylenebis(cyclohexyl isocyanate) fibers, PMFs) through polycondensation and wet-spinning process, exhibiting an inherent solid-solid phase transition property, adjustable phase transition behaviors, and outstanding knittability. The PMFs also present superior mechanical strength (28 MPa), washability (> 100 cycles), thermal cycling stability (> 2000 cycles), facile dyeability, and heat-induced recoverability, all of which are highly significant for practical wearable applications. Additionally, the PMFs can be easily recycled by directly dissolving them in solvents for reprocessing, revealing promising applications as sustainable materials for thermal management. Most importantly, the applicability of the PMFs was demonstrated by knitting them into permeable fabrics, which exhibit considerably improved thermal management performance compared with the cotton fabric. The PMFs offer great potential for intelligent thermal regulation in smart textiles and wearable electronics.

Ion diffusion retarded by diverging chemical susceptibility

For first-order phase transitions, the second derivatives of Gibbs free energy (specific heat and compressibility) diverge at the transition point, resulting in an effect known as super-elasticity along the pressure axis, or super-thermicity along the temperature axis. Here we report a chemical analogy of these singularity effects along the atomic doping axis, where the second derivative of Gibbs free energy (chemical susceptibility) diverges at the transition point, leading to an anomalously high energy barrier for dopant diffusion in co-existing phases, an effect we coin as super-susceptibility. The effect is realized in hydrogen diffusion in vanadium dioxide (VO2) with a metal-insulator transition (MIT). We show that hydrogen faces three times higher energy barrier and over one order of magnitude lower diffusivity when it diffuses across a metal-insulator domain wall in VO2. The additional energy barrier is attributed to a volumetric energy penalty that the diffusers need to pay for the reduction of latent heat. The super-susceptibility and resultant retarded atomic diffusion are expected to exist universally in all phase transformations where the transformation temperature is coupled to chemical composition, and inspires new ways to engineer dopant diffusion in phase-coexisting material systems.

Advancing thermal control in buildings with innovative cementitious mortar and recycled expanded glass/n-octadecane phase change material composites

This study delves into the role of phase change materials (PCMs) in bolstering energy efficiency, particularly in response to escalating global energy consumption in construction. The research focuses on integrating recycled expanded glass (REG) as a support material for shape-stabilized PCMs, specifically emphasizing n-octadecane (nOD) in cement mortars. With nOD exhibiting a melting point around 27 °C and a high latent heat thermal energy storage (TES) capacity of 241 J/g, various analyses, including DSC, FT-IR, SEM, TGA, and thermoregulation tests, assess the impact of different nOD/REG concentrations on TES properties. Alterations in physico-mechanical properties of mortar mixtures are noted with increasing REG/nOD content, impacting porosity and water absorption. The incorporation of REG/nOD PCMs decreases thermal conductivity, from 0.3620 W/mK (no PCM) to 0.1494 W/mK (full replacement). Thermo-regulation tests highlight PCM’s ability to counteract temperature fluctuations, surpassing results from other studies. Temperature difference outcomes (−10.60 °C daytime cooling, 4.00 °C nighttime heating) establish REG/nOD as promising for sustainable construction. The research evaluates PCM-infused concrete’s impact on building energy efficiency, noting significant heat demand reductions across climates and wall thicknesses. Carbon emissions decrease notably, especially with coal as the fuel source. Customized material thickness in PCM-integrated walls shows potential for substantial energy savings. These findings contribute valuable insights to the viability of REG/nOD composites in mitigating heating and cooling loads, advancing sustainable building solutions.

Vegetation Warming and Greenness Decline across Amazonia during the Extreme Drought of 2023

In 2023, most parts of the world experienced exceptional heat. In particular, anomalous warm temperatures and heatwave events were evidenced across South America during the second half of the year. The situation was particularly critical in the Amazon region in terms of not only hydrometeorological drought but also ecological and socioeconomic impacts. In this study, remote-sensing data collected from the Moderate Resolution Imaging Spectroradiometer (MODIS) were used to observe the changes in temperature and vegetation across Amazonia during the exceptional drought of 2023. This analysis was based on anomalies in the land surface temperature (LST) and vegetation indices: the enhanced vegetation index (EVI) and the normalized difference vegetation index (NDVI). The amplitude of the LST (AMP-LST), an indicator of the energy partitioning between the latent and sensible heat flux, and fire counts were also considered. The results show widespread and extreme warming across Amazonia during the austral spring in 2023, accompanied by a decline in vegetation greenness, water stress conditions across northern Amazonia, and an enhanced fire occurrence across central and northern Amazonia.

Research on Experimental and Simulated Temperature Control Performance of Power Batteries Based on Composite Phase Change Materials

The power battery is a key component of electric vehicles and its performance is greatly affected by temperature. Battery thermal management systems based on phase change materials can effectively control the battery temperature and at the same time have the advantages of simple structures, energy savings, and good temperature uniformity, and has broad development prospects. In this paper, expanded graphite–paraffin composite phase change materials were prepared, phase change material cooling experiments were carried out, and a phase change material cooling simulation model was also established using the Fluent software to study the influence of phase change material thermophysical parameters on thermal management performance. The results show that the phase change material thermal management method has excellent cooling performance. The best thermal management performance is achieved at the 3C discharge rate, with a phase change material filling thickness of 4 mm, a melting point of 40 °C above ambient temperature, and a thermal conductivity of 3 W/(m·K). When the phase change latent heat was increased from 150 J/g to 250 J/g, the liquid phase ratio decreased from 0.84 to 0.51, and the subsequent cooling performance was greatly improved, so the phase change latent heat should be increased as much as possible.

The Thermal Energy Storage Characteristics of Oleic Acid Modified ZnO‐Decorated Polymer Matrix‐Supported Composite Phase Change Materials: Synthesis and Characterization

AbstractIn this study, modified nano zinc oxide (ZnO)‐reinforced polymer‐supported novel thermally enhanced form‐stable composite phase change materials (PCMs) are presented, which are prepared via water in oil emulsion polymerization and following impregnation process steps. First, ZnO nanoparticles are modified with oleic acid (OA) to obtain lipophilic structures for emulsion stability, which are designed to take a role as a heat transfer activator. To ensure the shape stabilization of n‐hexadecane used as organic PCM, polymeric support materials are synthesized in the presence of modified ZnO nanoparticles (ZnO@OA). The polymeric frameworks exhibit open porous morphology, and the thermal stability of the support matrix improves with the addition of ZnO nanofiller. In the second step, composite PCMs are prepared by incorporation of n‐hexadecane with the solvent‐assisted vacuum impregnation method into polymer composites. The 1.0% ZnO@OA incorporated composite PCM has the highest incorporation ratio and exhibits a thermal storage capability (η) of 100%. According to the T‐history and thermal conductivity tests, it is observed that the heat conduction rate is enhanced with the addition of ZnO@OA nanofiller. The conclusion is that the obtained ZnO@OA integrated composite PCMs have a remarkable potential for latent heat storage applications requiring low temperature in the range of 5–25 °C.

Research on Experimental and Simulated Temperature Control Performance of Power Batteries Based on Composite Phase Change Materials

The power battery is a key component of electric vehicles and its performance is greatly affected by temperature. Battery thermal management systems based on phase change materials can effectively control the battery temperature and at the same time have the advantages of simple structures, energy savings, and good temperature uniformity, and has broad development prospects. In this paper, expanded graphite–paraffin composite phase change materials were prepared, phase change material cooling experiments were carried out, and a phase change material cooling simulation model was also established using the Fluent software to study the influence of phase change material thermophysical parameters on thermal management performance. The results show that the phase change material thermal management method has excellent cooling performance. The best thermal management performance is achieved at the 3C discharge rate, with a phase change material filling thickness of 4 mm, a melting point of 40 °C above ambient temperature, and a thermal conductivity of 3 W/(m·K). When the phase change latent heat was increased from 150 J/g to 250 J/g, the liquid phase ratio decreased from 0.84 to 0.51, and the subsequent cooling performance was greatly improved, so the phase change latent heat should be increased as much as possible.

Extensive Pollution of Uranus and Neptune’s Atmospheres by Upsweep of Icy Material during the Nice Model Migration

In the Nice model of Solar System formation, Uranus and Neptune undergo an orbital upheaval, sweeping through a planetesimal disk. The region of the disk from which material is accreted by the ice giants during this phase of their evolution has not previously been identified. We perform direct N-body orbital simulations of the four giant planets to determine the amount and origin of solid accretion during this orbital upheaval. We find that the ice giants undergo an extreme bombardment event, with collision rates as high as ∼3 per hour assuming km-sized planetesimals, increasing the total planet mass by up to ∼0.35%. In all cases, the initially outermost ice giant experiences the largest total enhancement. We determine that, for some plausible planetesimal properties, the resulting atmospheric enrichment could potentially produce sufficient latent heat to alter the planetary cooling timescale according to existing models. Our findings suggest that substantial accretion during this phase of planetary evolution may have been sufficient to impact the atmospheric composition and thermal evolution of the ice giants, motivating future work on the fate of deposited solid material.

Extensive Pollution of Uranus and Neptune’s Atmospheres by Upsweep of Icy Material during the Nice Model Migration

In the Nice model of Solar System formation, Uranus and Neptune undergo an orbital upheaval, sweeping through a planetesimal disk. The region of the disk from which material is accreted by the ice giants during this phase of their evolution has not previously been identified. We perform direct N-body orbital simulations of the four giant planets to determine the amount and origin of solid accretion during this orbital upheaval. We find that the ice giants undergo an extreme bombardment event, with collision rates as high as ∼3 per hour assuming km-sized planetesimals, increasing the total planet mass by up to ∼0.35%. In all cases, the initially outermost ice giant experiences the largest total enhancement. We determine that, for some plausible planetesimal properties, the resulting atmospheric enrichment could potentially produce sufficient latent heat to alter the planetary cooling timescale according to existing models. Our findings suggest that substantial accretion during this phase of planetary evolution may have been sufficient to impact the atmospheric composition and thermal evolution of the ice giants, motivating future work on the fate of deposited solid material.

The Thermal Energy Storage Characteristics of Oleic Acid Modified ZnO‐Decorated Polymer Matrix‐Supported Composite Phase Change Materials: Synthesis and Characterization

AbstractIn this study, modified nano zinc oxide (ZnO)‐reinforced polymer‐supported novel thermally enhanced form‐stable composite phase change materials (PCMs) are presented, which are prepared via water in oil emulsion polymerization and following impregnation process steps. First, ZnO nanoparticles are modified with oleic acid (OA) to obtain lipophilic structures for emulsion stability, which are designed to take a role as a heat transfer activator. To ensure the shape stabilization of n‐hexadecane used as organic PCM, polymeric support materials are synthesized in the presence of modified ZnO nanoparticles (ZnO@OA). The polymeric frameworks exhibit open porous morphology, and the thermal stability of the support matrix improves with the addition of ZnO nanofiller. In the second step, composite PCMs are prepared by incorporation of n‐hexadecane with the solvent‐assisted vacuum impregnation method into polymer composites. The 1.0% ZnO@OA incorporated composite PCM has the highest incorporation ratio and exhibits a thermal storage capability (η) of 100%. According to the T‐history and thermal conductivity tests, it is observed that the heat conduction rate is enhanced with the addition of ZnO@OA nanofiller. The conclusion is that the obtained ZnO@OA integrated composite PCMs have a remarkable potential for latent heat storage applications requiring low temperature in the range of 5–25 °C.

Multi-perspective analysis of adiabatic compressed air energy storage system with cascaded packed bed latent heat storage under variable conditions

Adiabatic compressed air energy storage (A-CAES) with advanced thermal energy storage systems has enormous potential in applications. In particular, the extent of thermal energy utilization determines the comprehensive performance of an A-CAES system. In this paper, a cascaded latent heat packed bed storage system is used as a thermal energy storage under variable conditions of A-CAES. The transient thermal characteristic of the packed bed under variable conditions are further studied. Moreover, the key parameters that affect the thermal energy utilization of the system are also parametrically investigated. The results show that the proposed system has a roundtrip efficiency of 63.42 %, an exergy efficiency of 66.58 %, and a payback period of 4.63 years. The economic analysis shows that the proposed system is more advantageous in comparison with A-CAES with heat transfer oil as heat storage system.

Statics Performance and Heat Dissipation Evaluation of Lattice Structures Prepared by Laser Powder Bed Fusion

This paper address the performance optimization of the battery heat sink module by analyzing the lattice structure of the battery heat sink module through in-depth modeling and simulation, and combining the laser powder bed fusion (LPBF)-forming technology with mechanical and corrosion resistance experiments for a comprehensive study. It is found that the introduction of the lattice skeleton significantly improves the thermal conductivity of the phase change material (PCM), realizing the efficient distribution and fast transfer of heat in the system. At the same time, the lattice skeleton makes the heat distribution in the heat exchanger more uniform, improves the utilization rate of the PCM, and helps to maintain the stability of the cell temperature. In addition, the melting of PCM in the lattice heat exchanger is more uniform, thus maximizing its latent heat capacity. In summary, by optimizing the lattice structure and introducing the lattice skeleton, this study successfully improves the performance of the battery heat dissipation system, which provides a strong guarantee for the high efficiency and stable operation of the battery, and provides new ideas and references for the development of the battery heat dissipation technology.

Eco‐friendly approach to thermal energy storage: Assessing the thermal and chemical properties of coconut biochar‐enhanced phase change material

AbstractPhase change materials (PCMs) can absorb, store, and release substantial latent heat within a specific temperature range during phase transition and have gained huge attention due to environmental concerns and energy crises. However, PCMs have a significant downside in energy storage due to their relatively lower thermal conductivity, leading to inadequate heat transfer (HT) performance. The foremost aim of the research is to synthesize an eco‐friendly coconut shell biochar (CSB) dispersed with organic A46 PCM in the temperature range of 44°C to 46°C to form a green nanocomposite. A two‐step approach is adopted to formulate the nanocomposites with different weight concentrations (0.2% and 0.8%) of green CSB particles. The developed nanocomposite's thermal conductivity and chemical stability were examined using a thermal properties analyzer and a Fourier transforms infrared spectrometer. The developed biochar composites have excellent thermal conductivity (0.39 W/m K) compared with base PCM (0.22 W/m K). Also, the developed nanocomposites were physically mixed together; there were no additional functional groups formed compared to pristine PCM, and the prepared materials were composite. Furthermore, a numerical analysis was performed using two‐dimensional energy modeling software to ascertain the HT rate of A46 composites. These thermally energized green nanocomposites show great promise for thermal energy storage and thermal management applications like battery thermal management, photovoltaic thermal systems, desalination systems, electronic cooling, building applications, and textiles.

Phase Change Materials for Thermal Energy Storage: A Concise Review

Thermal energy and its storage systems play an extensive role in day-to-day life. They store renewable energy and are capable of recovering generated heat from different systems. Storage of thermal energy can be classified into three types: sensible, latent and sorption heat storages. Thermal heat storages use different types of materials based on their capacity of heat storage, stability of duration and thermal conductivity. Various phase change materials (PCMs) that are suitable for thermal storage are reported. Low conversion ability limits their effectiveness. We reviewed some of the traditional materials synthesized recently that are used for thermal energy storage (TES). Recently developed TES materials exhibit high thermal conductivity, reduced super cooling and multiple phase change temperatures. Nano-enhanced PCMs produced an increase in thermal conductivity up to 32% with a reduction in latent heat by 32%. At this juncture, MXenes with high performance and extraordinary properties (thermal, mechanical, etc.) are of special significance. MXenes displayed an increased thermal conductivity up to 16% and 94% efficiency. In view of their structure and adaptability to be used in thermal storage systems, an attempt was made to review their role also in thermal storage applications. It is observed that MXenes highly impact storage and efficiency. Apart from MXenes, various types of PCMs along with their thermal characteristics are presented.

Improved solar still productivity using PCM and nano- PCM composites integerated energy storage

The study investigates the impact of Phase Change Material (PCM) and nano Phase Change Materials (NPCM) on solar still performance. PCM and a blend of NPCM are placed within 12 copper tubes submerged in 1 mm of water to enhance productivity. Thermal performance is assessed across four major scenarios with a fixed water level of 1 mm in the basin. These scenarios include the conventional still, equipped with 12 empty copper rods and 142 g of PCM in each tube, as well as stills with NPCM Samples 1 and 2. Sample 1 contains 0.75% nanoparticle concentration plus 142 g of PCM in the first 6 tubes, while Sample 2 features 2% nanoparticle concentration plus 142 g of PCM in the subsequent 6 tubes. Aluminum oxide (Al2O3) nanoparticles ranging in size from 20 to 30 nm are utilized, with paraffin wax (PW) serving as the latent heat storage (LHS) medium due to its 62 °C melting temperature. The experiments are conducted under the local weather conditions of Vaddeswaram, Vijayawada, India (Latitude-80.6480 °E, Longitude-16.5062 °N). A differential scanning calorimeter (DSC) is utilized to examine the thermal properties, including the melting point and latent heat fusion, of the NPCM compositions. Results demonstrate that the addition of nanoparticles enhances both the specific heat capacity and latent heat of fusion (LHF) in PCM through several mechanisms, including facilitating nucleation, improving energy absorption during phase change, and modifying crystallization behavior within the phase change material. Productivity and efficiency measurements reveal significant improvements: case 1 achieves 2.66 units of daily production and 46.23% efficiency, while cases 2, 3, and 4 yield 3.17, 3.58, and 4.27 units of daily production, respectively. Notably, the utilization of NPCM results in a 60.37% increase overall productivity and a 68.29% improvement in overall efficiency.