Diode Laser Research Articles

Implementation of Optical Coherent Communication System between Two Computers

This work represents implementation and investigation of optical coherent communication system between two computers. A single mode optical fiber is selected as transmission medium. The data are sent via the RS-232 standard interface with a bit rate of 9.6 kbps from personal computer (PC1) by line receive to convert the data from electrical levels (-12/+12 V) into TTL level (0/5 V). The modulation of this data was accomplished by internal modulation using laser diode type (HFCT-5208M) 1310 nm wavelength. The optical D-coupler was used to combine the optical signal that come from laser source with optical signal of laser local oscillator (OTS-304XI) at 1310/1550 nm wavelength to obtain coherent (homodyne and heterodyne) detection respectively. A PIN photodetector (HFCT-5208M) is used. Calculations of Signal to Noise Ratio (SNR) and Bit Error Rate (BER) for coherent detection were measured at different length of the optical fiber. Result show that high SNR and low BER for heterodyne detection than for homodyne detection.

Pure copper coating by multibeam directed energy deposition with blue lasers for antimicrobial effect

Pure copper has antimicrobial effect, and the development of pure copper coating technology for product surfaces is needed to prevent the spread of infections. To achieve high antimicrobial performance in coatings, it is essential to form a coating with high copper purity and minimal defects. In this study, we attempted to form a pure copper coating layer on a SS304 substrate using multibeam directed energy deposition with blue diode lasers. In the coating layer formation process, multiple bead layers are overlapped to form a smooth surface and two different types of joining is conducted simultaneously: the similar material joining area with the remelted previous layer, and the dissimilar-material joining area with the substrate. However, it was challenging to conduct this process for SS304 and pure copper due to their significantly different thermal properties. Therefore, we varied the hatching distance to control the heat input to both joining areas and investigated the effect on the quality of the coating layer. The results showed that there is an optimal ratio of similar and dissimilar joining areas, at which a high-quality coating layer with few voids and low dilution is formed. Furthermore, antimicrobial tests showed that the pure copper coating layer formed in this study exhibited the antimicrobial performance equivalent to those of a pure copper plate.

Broadband 1.45–2.1 μm luminescence in Er3+/Tm3+/Yb3+ tri-doped bismuth-germanate glasses

Optical properties of novel Er3+-doped, Er3+/Yb3+ and Er3+/Tm3+ co-doped and Er3+/Tm3+/Yb3+ tri-doped bismuth-germanate glasses were fabricated. Thermal characterization by differential scanning calorimetry showed the suitability of the glass for fiber drawing. Tri-doped sample presented a broadband luminescence spectrum ranging from 1450 to 2100 nm when it was excited by 980 and 1480 nm laser diodes. Energy transfer mechanisms from the donor (Yb3+, Er3+) to acceptor (Er3+, Tm3+) ions were found out to be the cause of the intense luminescence with broad bandwidth which can be tailored through doping content and concentration. It was observed that the Tm3+ addition helps broadening the luminescence spectrum, while the Yb3+ incorporation enhances the emission intensity. This study provides insightful contributions to the possibility of signal amplification in L + U-bands and beyond, up to 2100 nm.

Er3+/Tm3+ codoped CaF2 based oxyfluoroborosilicate glass-ceramics for fiber laser applications

Transparent Er3+/Tm3+ codoped CaF2 based oxyfluoroborosilicate glass-ceramics (BSEr1TmxGCs) with variable Tm3+ concentration were prepared through melt quench process followed by reheat treatment at 450 °C/1h. They were characterized through differential scanning calorimetry (DSC), powder X-ray diffraction (XRD), Fourier transform infrared (FTIR) Raman spectroscopy, near infrared (NIR) emission and luminescence decay. The formation of CaF2 nanocrystallites against oxyfluoroborosilicate glassy phase was confirmed by scanning electron microscopic (SEM) and hi-resolution transmission electron microscopic (HRTEM) studies. The NIR emission properties were investigated at 460 nm diode laser pumping. The applicability of BSEr1TmxGCs were examined by evaluating effective bandwidth (Δλeff), stimulated emission cross-section (σe), gain bandwidth (σe × Δλeff), figure of merit (σe × τR) and quantum efficiency (ηQE). The energy transfer efficiency (ηET), rate of energy transfer (WET) between Er3+ and Tm3+ and the rate of non-radiative transitions (WNR) were also calculated. The comparative NIR emission performance suggests that the BSEr1Tm1GC has proficiency for 1530 nm broadband fiber lasers and optical amplifiers in short wavelength and conventional wavelength (S + C) band communication window.

Dual-module combination with littman crosstalk external cavity for narrow-linewidth blue diode laser

The dense spectral beam combination is vital for achieving high power and brightness output in diode lasers. High-power narrow-linewidth laser modules have been widely studied as the fundamental units. This study presents a dual-module shared external cavity linewidth compression structure with a transmission diffraction grating. With a driving current of 2.4 A and a cooling temperature of 20 °C, the blue diode laser’s external cavity achieved an output power of 49.8 W, a spectral linewidth of 0.321 nm, and a tuning range of 0.817 nm, with an external cavity spectrum locked efficiency of approximately 80.6 %. Additionally, it is observed that crosstalk has a significant influence on the linewidth of the two modules. When one module current locked at 2.4 A and the other increased from 0 A to 2.4 A, the linewidth was reduced from 0.377 nm to 0.321 nm, and linewidth locking was implemented over an output power range from 27 W to 49.8 W. This work reports the highest output power for a blue diode narrow-linewidth external cavity laser.

Blue Laser for Production of Carbon Dots.

The synthesis of carbon dots (CDs) is gaining wide-ranging interest due to their broad applicability, owing to their small size and luminescence. CDs were prepared from charcoal via a one-step process using laser ablation in liquid without the use of reagents. The adopted method was based on the use of a commercially available continuous wave (CW) laser diode emitting a 450 nm wavelength and, for the liquid, a phosphate-buffered saline (PBS) solution, routinely used in the biological field. Photoluminescence analysis revealed fluorescence, at 480 nm, increasing with laser irradiation time. The atomic force microscopy (AFM) of the CDs revealed an average sphere shape with a size of about 10 nm. Biodegradable polycaprolactone (PCL), typically adopted in biomedicine applications, was used as a matrix to show the preserved luminescence, ideal for the non-invasive monitoring of implanted scaffolds in tissue engineering.

Non-contact photoacoustic imaging with a silicon photonics-based Laser Doppler Vibrometer

Photoacoustic imaging has emerged as a powerful, non-invasive modality for various biomedical applications. Conventional photoacoustic systems require contact-based ultrasound detection and expensive, bulky high-power lasers for the excitation. The use of contact-based detectors involves the risk of contamination, which is undesirable for most biomedical applications. While other non-contact detection methods can be bulky, in this paper, we demonstrate a proof-of-concept experiment for compact and contactless detection of photoacoustic signals on silicone samples embedded with ink-filled channels. A silicon photonics-based Laser Doppler Vibrometer (LDV) detects the acoustic waves excited by a compact pulsed laser diode. By scanning the LDV beam over the surface of the sample, 2D photoacoustic images were reconstructed of the sample.

B-174 Quantification of vitamin C in serum as a biomarker using the Laser Diode Thermal Desorption technique “LDTD”/Mass Spectrometry (Luxon)

Abstract Background Ascorbic acid (AA) or vitamin C, is a crucial substance that is involved in numerous physiological processes in living beings, including collagen production and antioxidant activity. When ascorbic acid is exposed to moisture, air, heat, light and oxygen, it oxidizes and turns into dehydroascorbic acid (DHAA). Our objective is to describe the sample preparation procedure and total quantification of AA and DHAA in human serum sample based on LDTD-MS/MS, and demonstrate its efficiency in quantification, combined with analysis selectivity and rapidity. Methods The Luxon is a sample introduction and ionization source that used a fiber-coupled laser diode to thermally desorb neutral molecules and charge them using a corona needle so they can be analyzed by mass spectrometry. Due to the instability of ascorbic acid, plasma samples were enriched and stabilized with an acidic solution. Sample preparation utilized a phosphate-containing buffer to minimize interferents and help volatize the analyte, followed by a precipitation step using acetonitrile to further clean the extract. Stable isotope-labeled internal standard (13C6 ascorbic acid) and homemade calibration curve and water quality controls were used for quantification. The analysis was performed using a Sciex 6500+ Triple Quad in APCI (Atmospheric Pressure Chemical Ionization) negative mode. Calibration curves ranging from 1 to 100 μg/mL and QCs were prepared in ascorbic acid-depleted serum (kept at room temperature/exposed to light for 4 days). The peak area against the internal standard (IS) ratio was used to normalize the signal. The calibration curves were plotted using the peak area ratio and the nominal concentration of standards. The following parameters were assessed for quantitative analysis: linearity, precision, accuracy, carryover and parallelism. A linear regression model with 1/X2 weighting was used to obtain the calibration curve equation and determine the correlation coefficient (r2). Parallelism was assessed by comparing the correlation coefficient of calibration curves prepared in water to six curves prepared with biological matrixes. Intra and inter assay precision and accuracy were determined by measuring QC samples ranging from low to high concentration in five replicates for 3 consecutive days. Results Calibration curves (n=3) showed excellent linearity. The calibration curve resulted in a linear response throughout the concentration range, the correlation coefficient was 0.99. For each quality control concentrations CVs were <10% complying with desirable specifications for imprecision and accuracy. Intra-assay CVs were 3.0-8.89% and inter-assay CVs were 7.64-9.79% for precision which reflects the agreement between repeated measurements. The results for accuracy showed similar results, intra-assay CVs were 3.83-9.20% and inter-assay CVs were 5.0-9.7%. Conclusions The new LDTD-MS/MS method described here has been validated as an effective technique to reliably and rapidly quantify ascorbic acid. Simple sample preparation, rapid acid stabilization combined with high yield allow analysis without degradation responses.

B-173 Cystine Analysis in Urine Sample Using the Laser Diode Thermal Desorption technique “LDTD”/Mass Spectrometry (Luxon)

Abstract Background Cystine is a polar amino acid found in the urine of healthy individuals; however, a genetic defect in renal transport can lead to cystine crystals and stones. A usual laboratory approach for diagnosing and monitoring cystinuria is to measure cystine concentration in 24-hour urine. The disease is rare, affecting around 1 in every 10,000 live births. The objective of this study was to develop a rapid assay using Tandem Mass Spectrometry methodology with an internal standard of Cystine derivatized in a urine sample, Luxon Ion Source®, Laser Diode Thermal Desorption (LDTD) technology. Methods The Luxon is a sample introduction and ionization source with a coupled laser diode, providing thermal uniformity, precision, accuracy and speed. Thermally desorbed neutral molecules are analyzed by mass spectrometry (MS). Initially, the sample was derivatized to make the cystine thermally vaporize, followed by liquid-liquid extraction assisted by salting out (SALLE). The isotope-labeled internal standard (Cystine-d4), homemade calibration curve and water quality controls were used for quantification. The analysis was performed using a Sciex 6500+ Triple Quad in APCI (Atmospheric Pressure Chemical Ionization) positive mode. The ratio of peak area to internal standard (ISTD) was used to normalize the signal. A linear regression model with 1/X2 weighting was used to obtain the calibration curve equation and determine the correlation coefficient (r2). Parallelism was assessed by comparing the (r2) of calibration curves prepared in water with six curves prepared with biological matrices. Intra- and interassay precision and accuracy were determined by measuring control samples ranging from low to high concentration in five replicates over 3 consecutive days. For urine analysis, aqueous calibration curves in the concentration range of 1 to 100 mg/L (n=3) showed excellent linearity. The following parameters were evaluated for quantitative analysis: linearity, precision, accuracy, carryover and parallelism.​ Results The calibration curve resulted in a linear response across the entire concentration range, the correlation coefficient (r) was 0.99. For each quality control concentration, CVs were <10%, meeting desirable imprecision and precision specifications. The intraassay CVs were 1.0-2.56% and the interassay CVs were 2.15-4.58% for precision, which reflects the agreement between repeated measurements. Precision results showed similar results, intra-assay CVs were 2.23-3.66% and inter-assay CVs were 1.0-2.77% Conclusions The new LDTD-MS/MS method for the determination of urinary Cystine was accepted after verification and validation of quality control parameters. The technique proved to be effective for reliably and quickly quantifying cystine in urinary samples from human patients, being a valuable tool in the diagnosis and prevention of cystine kidney stones. The assay developed, using the Luxon Ion Source®, based on LDTD (Laser Diode Thermal Desorption) technology, proved to be ultrafast for measuring derivatized cystine in urine

First fluoride ceramics lasing at 605 nm at ambient temperature fabricated from chemically synthesized powders

Laser ceramics have emerged as promising candidates of solid-state laser gain media. However, most laser ceramics are currently focused on lasing in the infrared wavelength range. The very limited options of host materials and the increased optical scattering losses at shorter wavelengths within ceramics have greatly limited the development of visible laser ceramics. Here we report visible laser ceramics with a composition of 0.5%Pr3+,5%Y3+:SrF2, in which a visible (orange) laser oscillation at 605 nm has been successfully achieved at room temperature pumped by InGaN blue laser diodes with a maximum slope efficiency of 8.1%. The ceramics were fabricated by vacuum hot pressing (VHP) of wet-chemistry synthesized 0.5%Pr3+,5%Y3+:SrF2 powders, followed by hot isostatic pressing (HIP). It was found that the visible laser ceramics exhibited a lower optical scattering loss along the processing pressure direction of the VHP process, indicating a uniaxial anisotropy in optical transmission within the ceramics. To our best knowledge, the current work is the first report on visible laser ceramics lasing in the orange region at ambient temperature, fabricated from chemically synthesized powders, which could pave the way for future scientific research on and industrial applications of more sophisticated and cost-effective visible laser ceramics.

High-power and ultra-wide-tunable fiber-type external-cavity diode lasers

High-power and wide-tunable fiber-type external-cavity diode lasers (FTECDLs) are of pivotal importance across various scientific and practical applications, such as polarization lidar, communication, sensing, and spectroscopy. As the output power and tuning characteristics are currently much lower than the saturation power and bandwidth of semiconductor gain media, further improvements conventionally require additional gain media in parallel and external amplifiers, resulting in lower energy efficiency and complex configurations. This study implemented energy manipulation in FTECDLs with a single gain medium, overcoming the mutual restriction between low damage threshold and laser output power. This approach makes it possible to completely exploit the intrinsic performance of the semiconductor gain medium. We demonstrated various FTECDL designs, achieving a maximum tuning range of 226.8 nm, maximum output power of 160 mW, and maximum optical signal-to-noise ratio of 86.3 dB with different configurations. These results are the highest levels ever achieved for E, S, C, L, and U bands. Additionally, the achieved polarization extinction ratio of nearly 38 dB has not been previously reported. Our work provides significant guidance for the design of traveling wave ring cavity (TWRC) lasers, including free-space light semiconductor and solid-state lasers with a TWRC.

Improving photoelectric characteristics of GaN-based green laser diodes by inserting electron blocking layer with gradient Al composition

This paper proposes four new gradient composition electron blocking layer (EBL) structures to enhance the photoelectric performance of GaN-based green laser diodes (LDs). The optical and electrical properties of new structure LDs are theoretically analyzed by LASTIP. It is observed that the implementation of a gradient composition EBL structure increases the effective barrier height for electrons, thereby better inhibiting the electron current overflow from the active region. In addition, the optical field leakage is effectively suppressed, lower threshold current and higher output power are obtained. The four different new structures have obvious differences in the improvement of the hole current injection and slope efficiency of multiple quantum well (MQW) LDs, and the underlying reasons for these phenomena are explored. Simulation results indicate that adopting a gradually descending Al component EBL structure yields optimal improvements in the photoelectric performance of LDs.

Evaluation of riboflavin, nanocurcumin, and hydrogen peroxide under light conditions: reduction of mature dental biofilms and enamel mineral loss

BackgroundBiofilms are a potential harbor for many microorganisms. The aim of this study was to test the efficacy of riboflavin (Rib), nano-micelle curcumin (NC), and hydrogen peroxide (HP), alone and in combination with the respective light (light-emitting diode (LED) or 980 nm diode laser) on the reduction of Streptococcus mutans and Lactobacillus acidophilus dual-species biofilms and their effect on the enamel mineral loss. Materials and methodsThe biofilms were formed on saliva-coated enamel slabs. Then, the biofilms were treated with antimicrobial photodynamic therapy (PDT) based on LED, Rib, and NC photosensitizers and with HP also based on a 980 nm diode laser (n = 8 per group). A crystal violet assay was performed to determine the reduction of the dual-species biofilms. The enamel slabs were analyzed for calcium and phosphorus content by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). ResultsWhile HP-PDT showed a reduction of 37% (p < 0.001), PDT with NC resulted in an even greater reduction of dual-species biofilms (40%, p < 0.001) than HP- and Rib-mediated PDT. In the EDX test, no significant difference was found between the control group and the treatment groups. ConclusionsThe use of natural photosensitizers such as NC in PDT has an effect that may be potentially important in reducing caries-causing bacteria.

Structural and optoelectronic study of MgLiX3 (X= Cl, Br, and I) halide perovskites: A DFT approach

This article presents in-depth information on the structural and optoelectronic properties of MgLiX3 (X = Cl, Br, and I) perovskites, and it suggests that MgLiX3 perovskites are promising materials for use in a variety of optoelectronic gadgets. The structural and optoelectronic properties of the compounds are determined utilizing first-principles calculations, with the density functional theory applied through the WIEN2k code. The structural stability was verified by computing the formation energy and binding energy. This study investigated the behavior of electronic conductivity and determined the bandgap values by employing TB-mBJ, which are 3.354 eV (MgLiCl3), 1.728 eV (MgLiBr3), and 0.067 eV (MgLiI3). Furthermore, optical properties such as absorption coefficient, reflectivity, conductivity, loss function, dielectric function, refractive index, and extinction coefficient were calculated and analyzed. In the visible range, MgLiBr3 and MgLiI3 exhibit their primary highest peaks of the absorption coefficient, which are 8.8 × 104 cm−1 for MgLiBr3 and 7.7 × 104 cm−1 for MgLiI3. On the other hand, MgLiCl3 demonstrates its initial highest peaks in the UV range, that is, 9 × 104 cm−1. The findings indicate that among the compounds studied, MgLiBr3 shows promise as a candidate for manufacturing solar cell devices based on the SQ limit, bandgap for typical perovskites (within 0.8–2.2 eV), and absorption in the visible range. MgLiCl3 is suitable for manufacturing several optoelectronic devices, such as laser diodes (LDs) and UV sensors due to having a high absorption coefficient in the ultraviolet region. With its low energy bandgap and high absorption coefficient in the IR to VR regions, MgLiI3 is well-suited for manufacturing photodetectors, LEDs, and other optoelectronic devices.

Periodontal Treatment of Gummy Smile with Diode Laser

Periodontal Treatment of Gummy Smile with Diode Laser

A novel diode laser intervention in the management of external invasive cervical resorption

Abstract “Invasive cervical resorption (ICR)” is a rare category of “external root resorption.” It is a progressive and destructive condition with an unclear cause. Managing external “ICR” presents a significant challenge, even to the most seasoned dental professionals. The removal of excessively vascularized granulation tissue is viewed as a pivotal step. This case report highlights the use of a diode laser to excise granulation tissue, by achieving optimal tissue ablation, promoting better healing, and subsequently restoring the severely damaged crown of the external ICR tooth with an intracanal fiber post.

Evaluation of Ovarian Reserve and Recurrence Rate After DWLS Diode Laser Ovarian Endometrioma Vaporization (OMAlaser): A Prospective, Single-Arm, Multicenter, Clinical Trial

Study ObjectiveTo evaluate the effectiveness of the Dual Wavelength Laser System (DWLS) diode laser on the treatment of ovarian endometrioma (OMA), with ablation and vaporization of the cystic capsule without performing the stripping technique, in terms of ovarian reserve and recurrence rate. DesignProspective, single-arm, multicenter, clinical trial. SettingMulticenter University Hospital. PatientsSeventy patients with symptomatic OMA. InterventionsPatients underwent surgery for primary unilateral or bilateral symptomatic OMA treated with DWLS diode laser vaporization. Following surgical intervention, patients were enrolled in a 12 months surveillance protocol featuring regular clinical assessments aimed at detecting ovarian reserve, pregnancy rate and any recurrence of the cyst and/or symptomatic relapse. Measurements and Main ResultsAntimullerian hormone (AMH) levels at the 3-month follow-up exhibited a significant difference from the baseline (p = .034), demonstrating a return to nearly presurgical values in the subsequent months. Antral follicle count (AFC) of the operated ovary showed a significant increase after treatment at the 6-month and 12-month follow-up (p = 0.005 and p = 0.002, respectively). Pregnancies were documented in 48.3% (14/29) of infertile patients who underwent treatment. OMA recurrence was observed in 4 patients (5.7%) at 12 months. No patient exhibited a significant relapse of the analyzed symptoms compared to baseline values. ConclusionThe findings of this study propose that DWLS diode laser presents a good option for treating OMA, demonstrating minimal impact on the surrounding healthy ovarian tissue, favorable pregnancy rate, coupled with low recurrence rates.

X-ray diffraction, luminescence, and electron paramagnetic resonance study of LaLuO3:Yb3+ nanopowders

The primary objective of materials science is the study of the properties of the existing materials and the development of new ones. In the present day, the use of solid-state lasers abroad has prompted material scientists globally to develop novel or enhance the properties of the existing active gain media. Materials comprising rare earth elements have historically proven effective in scintillation applications. The synthesis of LaLu1-xYbxO3 monodisperse nanopowders with a particle size of 50–62 nm via the Pechini complexing citrate method has been the subject of investigation using electron paramagnetic resonance (EPR) spectroscopy and photoluminescence (PL) measurements. The EPR data indicate that the Yb³⁺ ions predominantly create a single type of center, whereby the Yb³⁺ ion substitutes for the Lu³⁺ ion. The calculated EPR g-factors are estimated to be g1 = 3.85, g2 = 2.15, g3 = 1.55 and the 171Yb isotope hyperfine interaction constants are A1 = 600 × 10−4 cm−1, A2 = 700 × 10−4 cm−1, A3 ≈ 1800 × 10−4 cm−1. The principal values of the g factors and the hyperfine tensors indicate that the Yb site in LaLu1-xYbxO3 nanopowders exhibits orthorhombic symmetry. The PL measurements in the wavelength range of 350–1800 nm, with excitation provided by either a xenon lamp or a diode laser, indicate the presence of a broad emission band, centered at 404 nm, in addition to the well-known emission spectrum in the IR region (920–1100 nm) arising from Yb3+ ions.

Direct-modulated active mode-locking optoelectronic oscillator for microwave frequency comb signals

Abstract The optoelectronic oscillator (OEO) has been widely investigated to generate ultrapure microwave signals. For many applications, microwave signals with large bandwidth and multiple frequency bands, such as broadband microwave frequency comb (MFC) signals, are also needed. Conventional MFC signals are generated by active mode-locking OEO (AML-OEO) using devices such as Mach–Zehnder modulators (MZM) and delay fibers, which make the system structure more complicated and take a long time to build up stable oscillation at an oscillation mode. In this paper, A direct-modulated AML-OEO (DM-AML-OEO) is demonstrated with the advantages of compact design, cost-effectiveness, and straightforward integration. Mode-locked pulses are generated by direct-modulated Laser Diode (LD) which have low-phase noise. Furthermore, different comb spacings of MFC signals can be readily attained by adjusting the frequency of the active modulation signal (AMS) while supermodels are confined. In the experiments, the DM-AML-OEO produced MFC signals that exhibited a central frequency of 718 MHz and a frequency spacing of 100 kHz.

Laser and remineralising agents in dental erosion: a systematic review and meta-analysis.

This systematic review aimed to evaluate, by means of statistical comparison between selected studies, the effectiveness of laser irradiation on dental erosion applied alone or in combination with anti-erosive agents (fluoride, Acidulated phosphate fluoride APF and CPP-amorphous calcium fluoride phosphate CPP-ACFP), through optical profilometry and microhardness measurement. The searching strategy was conducted according to the International PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines, to answer research ques-tions regarding the effectiveness of lasers used in the context of dental erosion (such as Nd:YAG, CO2, Er:YAG, Er,Cr:YSGG, Diode, and Argon Ion lasers). A comprehensive and unrestricted sys-tematic searching was performed using the electronic databases of PubMed and Cochrane Library, for all articles published up to the end of January 2023. The review record was registered by the International prospective register of systematic reviews (PROSPERO) under the identification number CRD408639. Change in microhardness for the lasers group, irrespective of the type of laser used in the sample, was significantly greater compared with the one in the control group. Regards microhardness, the combination of Laser and APF gel showed promising results compared to APF gel agent.