Large Volume Injection Research Articles

PyICLab: An integrated Python-based toolkit for in-silico simulations of ion chromatography

PyICLab is an open-source Python-based package featuring an object-oriented programming (OOP) interface, providing tools for realistic and customized numerical simulations of ion chromatography (IC). In this paper, we showcase PyICLab's use in simulating diverse separation scenarios, including isocratic carbonate elution, gradient hydroxide elution, high-concentration and large-volume injections. The accuracy of the embedded models was validated by demonstrating strong correlations between predicted and experimental results. Additionally, PyICLab's capability to handle complex IC configurations was demonstrated through a simulation of a column-switching system for seawater analysis. PyICLab offers valuable resources for chromatographic optimization, method development, and educational purposes. It is available on PyPI at pypi.org/project/pyIClab. Interested readers can install PyICLab using the pip command in a Python 3.11 or higher environment.

Large scale screening and quantification of micropollutants in fish from the coastal waters of Cochin, India: Analytical method development and health risk assessment

Urban estuarine and coastal water receive several micropollutants through industrial and agricultural influxes. The bioaccumulation of these micropollutants in fish and their entry into the coastal population's food chain raises significant food safety concerns. Hence, a comprehensive analytical method was developed for ultra-trace level quantification of 345 micropollutants in fish. The optimized sample preparation method could extract compounds suitable for both GC–MS/MS and LC-MS/MS analysis simultaneously. The target list of contaminants included 278 agricultural pesticides and also 102 endocrine disruptors covering polyaromatic hydrocarbons, polychlorinated biphenyls, organochlorines, and endocrine-disrupting pesticides. The GC–MS/MS with large volume injection (LVI) technique, and LC-MS/MS operating in MRM mode, achieved an LOQ of <2.00 ng/g for most of the analytes. The extraction strategy involved tri-phase partitioning between water, acidified acetonitrile, and hexane, followed by salting out. Dispersive solid phase cleanup (dSPE) with C18, Z-Sep+, CaCl2, and MgSO4 was able to reduce the matrix influence, and the method achieved satisfactory recovery in the range of 70.0–120.0 % for all the target analytes. The repeatability and reproducibility relative standard deviation values of the measured analytes were <20.0 %, and the Horwitz ratio values were well below 2. The method was used to accurately measure the target micropollutants in fish from the Cochin estuary, the highly urbanized portion of the Vembanad Lake, and an important Ramsar site. At least one or more of the 41 different micropollutants were identified and quantified in about 90.7 % of the 108 samples analyzed. The importance of large-scale screening and trace-level quantification methods in environmental monitoring and risk assessment is underscored by the results. The risk assessment showed a moderate risk of exposure to the nearby coastal population through the food chain.

Analysis of Total Microcystins using LC-MS/MS: Method Improvements and Sample Applications

Microcystin variants (MCs), including microcystin-LR (MC-LR) and related variants, are produced by cyanobacteria and are regulated due to their potential health risks. Current methods for MC analysis predominantly employ LC-MS/MS, limited by the availability of reference materials necessary for quantification. As an alternative method for total MC quantification, the analysis of 2-methyl-3-methoxy-4-phenylbutyric acid (MMPB), formed by oxidation of the common ADDA structure in MCs, offers economic and practical advantages by avoiding the need for multiple MC reference materials. This method allows total MC quantification across various matrices, independent of specific MC variants. In this study, we evaluated the utility of MMPB-d3 as a surrogate to assess recovery rates throughout the processes critical for MMPB quantification. Comparative analysis with 4-phenylbutyric acid (4-PB) highlighted the stability of MMPB-d3 under oxidative conditions, which is critical for its application as a surrogate or internal standard. The oxidation process was optimized to achieve consistent recovery rates, averaging 101%, ensuring reliable conversion of MCs to MMPB for subsequent analysis. The limit of quantification (LOQ) has been improved due to the large volume injection of up to 0.1 µg/L. Comparison of MMPB concentrations from field samples with conventional LC-MS/MS results showed a significant correlation (r = 0.80, p &lt; 0.005), but with variations in the absolute concentrations. Calculations using a formulation model with MMPB concentrations allowed us to estimate total MC levels, demonstrating the potential of the proposed method to complement existing target measurement techniques.

Chemical Exposomics in Human Plasma by Lipid Removal and Large-Volume Injection Gas Chromatography-High-Resolution Mass Spectrometry.

For comprehensive chemical exposomics in blood, analytical workflows are evolving through advances in sample preparation and instrumental methods. We hypothesized that gas chromatography-high-resolution mass spectrometry (GC-HRMS) workflows could be enhanced by minimizing lipid coextractives, thereby enabling larger injection volumes and lower matrix interference for improved target sensitivity and nontarget molecular discovery. A simple protocol was developed for small plasma volumes (100-200 μL) by using isohexane (H) to extract supernatants of acetonitrile-plasma (A-P). The HA-P method was quantitative for a wide range of hydrophobic multiclass target analytes (i.e., log Kow > 3.0), and the extracts were free of major lipids, thereby enabling robust large-volume injections (LVIs; 25 μL) in long sequences (60-70 h, 70-80 injections) to a GC-Orbitrap HRMS. Without lipid removal, LVI was counterproductive because method sensitivity suffered from the abundant matrix signal, resulting in low ion injection times to the Orbitrap. The median method quantification limit was 0.09 ng/mL (range 0.005-4.83 ng/mL), and good accuracy was shown for a certified reference serum. Applying the method to plasma from a Swedish cohort (n = 32; 100 μL), 51 of 103 target analytes were detected. Simultaneous nontarget analysis resulted in 112 structural annotations (12.8% annotation rate), and Level 1 identification was achieved for 7 of 8 substances in follow-up confirmations. The HA-P method is potentially scalable for application in cohort studies and is also compatible with many liquid-chromatography-based exposomics workflows.

Rapid and simultaneous determination of ultrashort-, short- and long- chain perfluoroalkyl substances by a novel liquid chromatography mass spectrometry method

Per- and Polyfluoroalkyl Substances (PFAS) are a group of persistent organic pollutants that have received considerable attention from public and regulatory groups. Due to regulations of long-chain PFAS, the use of short-chain and ultrashort-chain PFAS is rapidly growing. Thus, there is an urgent need to develop quantitative methods for determining PFAS with different chain lengths in various environmental matrices. This study introduces an innovative liquid chromatography-mass spectrometry (LC-MS) system combining large volume injection (LVI) and online solid phase extraction (SPE). This system incorporates three columns: a reverse-phase (RP) column, a weak anion exchange (WAX) trap column, and a hybrid HILIC/ion-exchange (HILIC/IE) column, controlled by two valves. With valve switching, ultrashort-chain PFAS that are not retained by the RP column are enriched by the trap column, while other PFAS are separated by the RP column. The trapped ultrashort PFAS are then transferred to the HILIC/IE column for further separation. The LVI significantly enhances the method's sensitivity, allowing for rapid and simultaneous determination of ultrashort-, short- and long- chain PFAS in aqueous samples. The matrix effects from various environmental samples were evaluated, and the results indicate that this unique LC-MS method is suitable for analyzing all chain-length PFAS in various matrices, including surface water, sewage effluent, and seawater. Finally, this novel LC-MS method was applied to quantify PFAS in various water samples.

Nonlinear Tissue Permeability Drives Tissue Pressure and Injection Distribution: A Computational Investigation of Subcutaneous Injections.

There is a significant opportunity to expand the understanding of subcutaneous injection mechanics with an aim to increase injectable volume while controlling tissue strain and associated subject pain. Computational modeling can evaluate the mechanics of subcutaneous injections as a supplement to experimental, animal and clinical studies. The objectives of this study are to (1) develop a computational model for subcutaneous injection in tissue, (2) investigate the influence anisotropic tissue permeability has on bolus formation, and (3) explore the effects that injection flow rate and viscosity have on injection flow and tissue strain. Poroelastic models with subsurface flow were implemented in finite element software (COMSOL, ABAQUS). Pore pressure and injectate distribution showed excellent agreement with experimental results when evaluated at multiple injection rates (20 ml/hr, 120 ml/hr and 360 ml/hr). Including the anisotropy of tissue permeability causes the injectate to preferentially spread horizontally, similar to experimentally observed bolus distributions. Cases are presented to provide additional insight into injection mechanics, including variations on the delivery rate, the injection volume, viscosity and the thickness of the subcutaneous layer. The results support the use of computational modeling as a valid tool for understanding tissue strains and injectate distributions for large volume injections.

A comprehensive study on solvent effect and establishment of n-hexane solvent system based normal-phase liquid chromatography × reversed-phase liquid chromatography for isolation of natural products

Reversed-phase liquid chromatography (RPLC) represents an effective separation method, and is widely employed as the second dimension in most 2D-LC systems. Nevertheless, the solvent effect of the eluent from the first dimension on RPLC presents a challenge to the online coupling of RPLC with other separation modes, particularly normal phase liquid chromatography (NPLC). To address this issue, a comprehensive understanding of the solvent effect is essential. Following a comprehensive investigation into the influence of diverse solvents on RPLC separations, it was observed that alkane solvents, such as n-hexane, exhibited a pronounced tendency to be retained during RPLC separations. Such solvents do not affect the analysis of samples with weaker retention abilities than themselves, even when a large injection volume is used. The solvent effect was thus reduced by employing n-hexane-based solvent dilution. Leveraging the markedly enhanced solvent tolerance and extensive injection volume in RPLC, a versatile integration of the NPLC and RPLC was devised, necessitating merely a purge pump and a 10 port 2 position valve in conjunction with two sample loops. The novel 2D-LC system was then deployed for the analysis of propolis, a naturally occurring complex sample, and demonstrated remarkable separation efficiency.

LVI and DI-SPME Combined with GC/MS and GC/MS for Volatile Chemical Profile Investigation and Cytotoxic Power Evaluation of Essential Oil and Hydrolate from Cannabis sativa L. cv. Carmagnola.

Cannabis sativa L. is a plant that has been cultivated since ancient times thanks to its various uses. Even its extraction products, such as essential oil and hydrolate, having a varied chemical composition and rich in bioactive components, find wide use in different sectors, gathering ever-increasing interest over time. In this work, the essential oil of Cannabis sativa L. cv. Carmagnola was characterized by using Gas Chromatography/Mass Spectrometry (GC/MS) and, for the first time, the chemical profile of the hydrolate was also described through different analytical techniques such as Large-Volume Injection Gas Chromatography/Mass Spectrometry (LVI-GC/MS) and Direct Immersion-Solid Phase Microextraction-Gas Chromatography/Mass spectrometry (DI-SPME-GC/MS), in order to provide a more complete compositional profile. The results of the analyses conducted on the hydrolate highlighted a high content of α-terpineol; on the other side, in the essential oil, a prevalence of monoterpenes, with α-pinene and limonene as the characterizing components, was detected. Both matrices were also investigated to evaluate their cytotoxic activity by using a panel of cancer cell lines derived from different histotypes such as melanoma (A375, LOX IMVI), non-small cell lung cancer (H1299, A549), colon (HT29) and pancreatic (L3.6) cancer cell lines. The obtained data demonstrated that essential oil was more effective than hydrolate in terms of reduction in cell viability.

Highly sensitive two-dimensional ion chromatography mass spectrometry method for nitrite determination in hydroxypropyl methylcellulose

Due to their potential adverse health effects, some N-nitrosamines in drug products are strictly regulated with very low maximum daily intake limits. Nitrosamines can be formed from the reaction of nitrite and secondary or tertiary amines when both species co-exist in the drug synthesis or formulation process. One key strategy to mitigate nitrosamine risk in drugs is to select low-nitrite containing pharma excipients for formulation. It is necessary to develop a sensitive method for trace nitrite determination in pharma excipients as it enables drug producers to study nitrosamine formation kinetics and select excipient suppliers. This study details the development and validation of a two-dimensional ion chromatography mass spectrometry (2D-IC/MS) method for trace nitrite determination in hydroxypropyl methylcellulose (HPMC), one of the most important pharmaceutical excipients used in many drug formulations. The 2D-IC system was operated in heart-cutting mode with a concentrator column coupling the two dimensions. A standard bore anion-exchange column was used in the first dimension (1D) to enable a large volume injection for increased sensitivity and provide improved resolution between nitrite and the interfering chloride peak. A high efficiency microbore anion-exchange column with different selectivity was used in the second dimension (2D) to resolve nitrite from other interfering species. The use of 2D-IC resulted in significantly improved resolution, solving the sensitivity loss issue due to ion suppression from an otherwise 1D separation. MS detection with selective ion monitoring and isotope labeled nitrite internal standard further improve the method specificity, accuracy, and ruggedness, as compared with conductivity detection. For trace determination, it is also extremely important to have a clean blank. For this purpose, a novel cleaning procedure using a strong anion wash was developed to remove nitrite contamination from labware. The optimized method was validated with linearity of nitrite in the concentration range of 18.5–5005.8 ng/g having a regression coefficient of >0.9999, precision with RSD at 3.5–10.1 % and recovery of 90.5–102.4 %. The limit of detection and limit of quantitation were 8.9 and 29.6 ng/g relative to the HPMC sample, or equivalent to 89 and 296 pg/g in the sample solution, respectively.

Pharmacokinetics in regional anesthesia.

Pharmacokinetics of local anesthetics are one of the main determinants of success and safety of regional anesthesia and comprise local and systemic distribution phases. This review aims to summarize the latest research findings on this topic in the context of various regional blocks performed for different surgeries and patient populations. Research into local kinetics and systemic absorption of local anesthetics has chiefly been focused on novel fascial plane blocks, especially the erector spinae plane block, as these are increasingly adopted for regional anesthesia and pain management. As their clinical efficacy is very dependent on injection of large volumes of local anesthetic, doses over typically recommended limits are often administered. Fascial plane blocks are the regional anesthesia techniques in need of the most pharmacokinetic characterization, not only to better understand their complex mechanisms of action but also to avoid harm from excessive doses of local anesthetics. Further mapping of risk factors for systemic toxicity from administration in different block sites is crucial. Extremes of age and pregnancy are vulnerable patient populations but in whom regional anesthesia, including novel techniques, has been performed with few complications.

Effect of lateral stress on frictional properties of a fracture in sandstone

The injection of large volumes of natural gas into geological formations, as is required for underground gas storage, leads to alterations in the effective stress exerted on adjacent faults. This increases the potential for their reactivation and subsequent earthquake triggering. Most measurements of the frictional properties of rock fractures have been conducted under normal and shear stresses. However, faults in gas storage facilities exist within a true three-dimensional (3D) stress state. A double-direct shear experiment on rock fractures under both lateral and normal stresses was conducted using a true triaxial loading system. It was observed that the friction coefficient increases with increasing lateral stress, but decreases with increasing normal stress. The impact of lateral and normal stresses on the response is primarily mediated through their influence on the initial friction coefficient. This allows for an empirical modification of the rate-state friction model that considers the influence of lateral and normal stresses. The impact of lateral and normal stresses on observed friction coefficients is related to the propensity for the production of wear products on the fracture surfaces. Lateral stresses enhance the shear strength of rock (e.g. Mogi criterion). This reduces asperity breakage and the generation of wear products, and consequently augments the friction coefficient of the surface. Conversely, increased normal stresses inhibit dilatancy on the fracture surface, increasing the breakage of asperities and the concomitant production of wear products that promote rolling deformation. This ultimately reduces the friction coefficient.

New Frontiers in Wide-Awake Surgery.

After studying this article, the participant should be able to: 1. Explain the most important benefits of wide-awake surgery to patients. 2. Tumesce large parts of the body with minimal pain local anesthesia injection technique to eliminate the need for sedation for many operations. 3. Apply tourniquet-free surgery to upper and lower limb operations to avoid the sedation required to tolerate tourniquet pain. 4. Move many procedures out of the main operating room to minor procedure rooms with no increase in infection rates to decrease unnecessary cost and solid waste in surgery. Three disruptive innovations are changing the landscape of surgery: (1) minimally painful injection of large-volume, low-concentration tumescent local anesthesia eliminates the need for sedation for many procedures over the entire body; (2) epinephrine vasoconstriction in tumescent local anesthesia is a good alternative to the tourniquet and proximal nerve blocks in extremity surgery (sedation for tourniquet pain is no longer required for many procedures); and (3) evidence-based sterility and the elimination of sedation enable many larger procedures to move out of the main operating room into minor procedure rooms with no increase in infection rates. This continuing medical education article explores some of the new frontiers in which these changes affect surgery all over the body.

Sensitivity and quantitativeness of large-volume injection combined with liquid chromatography/high-resolution mass spectrometry for target screening analysis of emerging contaminants

Solid phase extraction (SPE) has been widely used for pretreatment in target screening (TS) analysis. However, some compounds are difficult to recover by SPE or their recovery is unstable for environmental samples. In this study, we tested large-volume injection (LVI) without SPE for TS analysis of 103 compounds listed by the Ministry of the Environment (Japan)—so-called ‘items to be surveyed’—using liquid chromatography high-resolution mass spectrometry. We evaluated the limit of quantification (LOQ) by LVI and compared this LOQ with the LOQ by SPE pretreatment using a hydrophilic-lipophilic balance (HLB) combined with activated carbon, which was found previously to afford the best SPE cartridges for target compounds recovery. The LOQ generally decreased as the injection volume increased, and the LOQ was at least 250 times lower for a 500-μL injection than for a 2-μL injection for half of the compounds. LVI provided LOQs lower than the predicted no effect concentration for more compounds than the SPE method. The average matrix effect (ME) by LVI was in the range 70%–130% for 69 out of 97 compounds. The ME was higher or lower for some of the remaining compounds, but the ME was in the range 10%–1000% for all 18 water samples for 84 of the 97 compounds. Comparing the ME by LVI and the recovery ratio by the SPE method showed that LVI achieved more accurate quantitation than the SPE method for a larger number of compounds. Therefore, LVI provides better sensitivity and quantitativeness than the SPE method using HLB and activated carbon for TS analysis of as many ‘items to be surveyed’ as possible.

Magmatic conditions aiding synconvergent extension above the Peruvian flat slab

Abstract The Cordillera Blanca and Cordillera Huayhuash contain some of the highest topography in the Andes and provide insight into tectonomagmatic processes associated with the onset of flat-slab subduction. These adjacent ranges shared a similar history of deformation and exhumation prior to the late Miocene, when synconvergent extension began in the Cordillera Blanca. Magmatism in the Cordillera Huayhuash has been inferred as coeval with magmatism in the Cordillera Blanca. Yet, extension, which has been correlated with magmatic heat flow, is limited to the Cordillera Blanca. New zircon U-Pb dates and trace and rare earth element concentrations from the Cordillera Blanca batholith and the Huayllapa pluton in the Cordillera Huayhuash and reassessment of existing zircon data help to characterize regional magmatic processes prior to the establishment of flat-slab subduction. Two compositionally distinct samples of the Huayllapa pluton yielded mean ages of 24.8 ± 0.4 Ma and 25.4 ± 0.8 Ma. In contrast, the Cordillera Blanca batholith has a protracted crystallization history postdating that of the Cordillera Huayhuash by up to 20 m.y. Miocene magmatism in the Cordillera Blanca began at 19 Ma and ended with injection of large volumes of geochemically distinct, mantle-derived magma from 10 to 5 Ma. We suggest that 6–5 Ma magmatism in the Cordillera Blanca promoted elevated heat flow and reduced shear strength, which facilitated extensional shearing along the western slopes of the range, whereas colder amagmatic crust in the Cordillera Huayhuash inhibited southward propagation of faulting. Our data demonstrate that the linkages between magmatism and elevated heat flow identified in the Cordillera Blanca are important driving processes in initiating extension in cordilleran-style orogenies.

Effects of saturated fluids on petrophysical properties of hot dry rock at high temperatures: An experimental study

Hydraulic fracturing is a crucial technology for efficient heat extraction from hot dry rock (HDR). The fracturing process involves the injection of large volumes of cold fluids, which can significantly affect the petrophysical properties of the rock, particularly when temperature differences and fluid-rock interactions are taken into account. However, there is a lack of research on the evolution of HDR petrophysical properties under the influence of different fluids at high temperatures. In this paper, we utilized a high-temperature high-pressure tri-axial loading system, rock spontaneous imbibition instrument, porosity-permeability tester, and thermal conductivity meter, along with comprehensive analysis techniques such as ultrasonic wave velocity monitoring, CT scanning, and nuclear magnetic resonance (NMR), to systematically investigate the effects of distilled water and nano emulsion on the physical and mechanical properties of the HDR at high temperatures. Through comparison with the experimental results of dry samples, comprehensive characteristics of physical parameters for the HDR under the influence of distilled water and nano emulsion are obtained, such as spontaneous imbibition mass and permeability, thermal physical properties, and rock mechanical parameters. The experimental results show that temperature increase promotes the formation of massive thermal damage fractures in the HDR samples, and the fluid weakens the mechanical strength of the HDR. When the effects of temperature and saturated fluids are combined, the hydraulic fracture network in the HDR samples exhibits increased complexity, contrasting with the fracture patterns observed in the heat-treated dry samples. The distilled water has a more pronounced effect on weakening the mechanical strength of the samples than the nano emulsion. Moreover, the analyses of permeability, thermal conductivity, ultrasonic wave velocity, and NMR results are consistent with the results of mechanical experiments. As the temperature rises, the wave velocity of saturated distilled water samples exceeds that of both saturated nano emulsion samples and dry samples, the velocity of the saturated fluid front in the samples increases, and the range of the fluid in the pores expands. Overall, these findings provide valuable experimental evidence and theoretical guidance for better understanding the hydro-thermal-mechanical behaviors of the HDR, which are crucial for the efficient development and utilization of geothermal energy.

Comparative efficacy of low-volume retrobulbar anesthesia using three commercial local anesthetics in adult horses.

To compare the efficacy of low-volume (5-mL) locoregional retrobulbar anesthesia ("retrobulbar block") by use of 3 commercial local anesthetic formulations. 8 healthy adult mares. A block-randomized, masked, controlled design was used. A single ultrasound-guided retrobulbar block was performed with 2% lidocaine, 2% mepivacaine, or 0.5% bupivacaine (n = 5 eyes/group). Contralateral eyes served as untreated controls. End points performed at baseline and time intervals up to 24 hours postblock included the following: assessment of neurophthalmic reflexes/responses, intraocular pressure, and vertical pupil diameter measurement, corneal and periocular esthesiometry, and observation for adverse effects. Low-volume block did not result in increased intraocular pressure or other adverse effects at any time point in any treatment group. Statistically significant corneal anesthesia (P < .001) was observed 1 minute after block in all groups, persisting through 4 hours after lidocaine or mepivacaine block and through 24 hours after bupivacaine block. Clinically significant periocular anesthesia was not observed in any group. Significant vertical pupil diameter increase (P < .05) was observed for up to 4 hours after lidocaine or mepivacaine block and 6 hours after bupivacaine block. Low-volume retrobulbar block with any of the 3 local anesthetic drugs evaluated was not associated with adverse effects. In terms of efficacy, mepivacaine block showed no clinical advantage over lidocaine block. However, bupivacaine block induced comparatively rapid and sustained corneal anesthesia. In comparison to published findings using a larger injection volume, low-volume retrobulbar block with lidocaine produced clinically comparable corneal anesthesia. However, periocular soft tissue anesthesia was not achieved with any local anesthetic drug at low volume.

Vulvar migration of injected polyacrylamide hydrogel following breast augmentation: a case report and literature review

BackgroundVulvar migration is a rare complication of filler injection for breast augmentation, generally presenting as repeated pain and fever. We will report a case of woman with polyacrylamide hydrogel breast injection develops vulvar abscess.Case presentationA woman with a history of polyacrylamide hydrogel breast injection was noted to have vulvar abscess due to migration of filler materials. Filler removal surgery and vacuum sealing drainage was performed for this patient. The patient was discharged from the hospital with no further complications. After a review of pertinent literature, only four previous case reports are found. Local inflammatory response, infection, large volume injections, inframammary fold destruction, hematogenous or lymphatic migrate, trauma, gravity and external pressure could play essential parts in the migration of injected filler.ConclusionPolyacrylamide hydrogel migration poses a worldwide challenge, necessitating personalized solutions. Our case study underscores the importance of comprehensive examinations for individuals with a history of filler breast injection when suspecting vulvar filler migration.

Determination of ultra-trace level Cr(vi) in seawater using large-volume direct injection by LC-ICP-MS with in-line matrix elimination

A method to improve the sensitivity of LC-ICP-MS for the determination of hexavalent chromium (Cr(vi)) in seawater by using the large volume injection and in-line matrix elimination.

Development of a column switching for direct online enrichment and separation of polar and nonpolar analytes from aqueous matrices

Trace substances in surface waters may threaten health and pose a risk for the aquatic environment. Moreover, separation and detection by instrumental analysis is challenging due to the low concentration and the wide range of polarities. Separation of polar and nonpolar analytes can be achieved by using stationary phases with different selectivity. Lower limits of detection of trace substances can be obtained by offline enrichment on solid phase materials. However, these practices require substantial effort and are time consuming and costly. Therefore, in this study, a column switching was developed to enrich and separate both polar and nonpolar analytes by an on-column large volume injection of aqueous samples. The column switching can significantly reduce the effort and time for analyzing trace substances without compromising on separation and detection. A reversed phase (RP) column is used to trap the nonpolar analytes. The polar analytes are enriched on a porous graphitized carbon column (PGC) coupled serially behind the RP column. A novel valve switching system is implemented to enable elution of the nonpolar analytes from the RP column and, subsequently, elution of polar analytes from the PGC column and separation on a hydrophilic interaction liquid chromatography (HILIC) column. To enable separation of polar analytes dissolved in an aqueous matrix by HILIC, the water plug that is flushed from the PGC column is diluted by dosing organic solvent directly upstream of the HILIC column. The developed method was tested by applying target analysis and non-target screening, highlighting the advantage to effectively separate and detect both polar and nonpolar compounds in a single chromatographic run. In the target analysis, the analytes, with a logD at pH 3 ranging from -2.8 to + 4.5, could be enriched and separated. Besides the 965 features in the RP phase, 572 features from real wastewater were observed in the HILIC phase which would otherwise elute in the void time in conventional one-dimensional RP methods.

Sensitive analysis of selenium speciation in natural seawater by isotope-dilution and large volume injection using PTV-GC-ICP-MS

Although oceans play a key role in the global selenium (Se) cycle, there is currently very little quantitative information available on the distribution of Se concentrations and Se speciation in marine environments. In general, determining Se concentration and speciation in seawater is highly challenging due to very low Se levels ((sub)ng⋅L−1), whereas matrix elements interfering Se pre-concentration and detection are up to the g⋅L−1 levels. In this study, we established a sensitive method for the determination of the various Se chemical fractions present in natural seawater, i.e. selenite (SeIV), selenate (SeVI), organic Se-II + Se0 and total Se, using species-specific isotope dilution gas chromatography coupled to inductively coupled plasma mass spectrometry (ID-GC-ICP-MS). We compared different derivatization reagents and optimized specific pre-treatment protocols, including a microwave assisted oxidation protocol for the determination of total Se and organic Se-II + Se0 using H2O2. To increase sensitivity, we developed an online pre-concentration method based on large volume injection (LVI) using a programmed temperature vaporization (PTV) inlet. Eventually, the developed method achieved low absolute and methodological detection limits, i.e., respectively, 0.1–0.3 pg and 0.9–3.1 ng.L-1 for the different fractions. The accuracy of our method was of 2% for a certified reference material (CRM) diluted in artificial seawater while the precision was better than 4% for a freshwater CRM in artificial seawater matrix as well as two common seawater CRMs certified for trace elements excluding Se. As a proof-of-concept, we quantified the various Se fractions in a large number of natural water samples from the Baltic and North Seas, encompassing a wide range of salinity (7–35 psu), which shows that its detection limits are sufficient to determine total Se, SeIV, SeVI and organic Se-II + Se0 concentrations in brackish and marine systems.