Lambertian Equivalent Reflectivity Research Articles

Evaluation of total ozone measurements from Geostationary Environmental Monitoring Spectrometer (GEMS)

Abstract. The continued interest in air pollution and stratospheric ozone variability has motivated the development of a Geostationary Environmental Monitoring Spectrometer (GEMS) for hourly ozone monitoring. This paper provides the atmospheric science community with the world's first assessment of GEMS total column ozone (TCO) retrieval performance and diurnal ozone variation. The algorithm used for GEMS is a more advanced version of its predecessor, the Total Ozone Mapping Spectrometer (TOMS) V8, that incorporates several improvements, including a new lookup table, a simple Lambertian-equivalent reflectivity model, and a spectral dependence correction. The GEMS algorithm also uses the optimal estimation method (OEM) to make error analysis more accessible and robust. The estimated retrieval errors range from 1.5 to 2 DU in September and 2 DU in December, with a constant degree of freedom of the signal (DFS) of 1 in September and a variable DFS of 1.25 to 1.4 in December throughout the day, depending on solar zenith angle (SZA). To assess the performance of the GEMS algorithm, the hourly GEMS total ozone was compared with ground-based measurements from Pandora instruments and other satellite platforms from TROPOMI (TROPOspheric Monitoring Instrument) and OMPS (Ozone Mapping and Profiler Suite Nadir Mapper). GEMS has a high correlation of 0.97 and small RMSE values compared to Pandora TCO at Busan and Seoul in South Korea. It is notable that despite exhibiting seasonal dependence in the mean bias of GEMS with Pandora, GEMS is capable of observing daily variations in ozone that are highly consistent with Pandora measurements, with a bias of approximately 1 %. The comparison of GEMS TCO data with TROPOMI and OMPS TCO data shows a high correlation of 0.99 and low RMSE compared to TROPOMI and OMPS TCO data, but the data have a negative bias of −2.38 % and −2.17 %, with standard deviations of 1.33 % and 1.57 %, respectively. Similar to OMPS, the influence of SO2 from volcanic eruptions is not properly removed in some regions, leading to GEMS overestimating TCO in those areas. The mean biases of GEMS TCO data with TROPOMI and OMPS TCO are within ±1 % at low latitudes but become negative at midlatitudes, with an increasingly negative dependence on latitude. Furthermore, this dependence becomes more prominent from summer to winter. The empirical correction applied to the GEMS irradiance data improves the dependence of the mean bias on season and latitude, but a consistent bias still remains, and a marginal positive trend was observed in December. Therefore, further investigation into correction methods is needed. The results are a meaningful scientific advance by providing the first validated, hourly UV ozone retrievals from a satellite in geostationary orbit. This experience can be used to advance research with future geostationary environmental satellite missions, including the incoming TEMPO (Tropospheric Emissions: Monitoring of Pollution) and Sentinel-4.

High sensitivity of Aeolus UV surface returns to surface reflectivity

Global ultraviolet (UV) surface reflectivity climatologies are all composed from daylight passive remote sensing observations of reflected UV light, generally integrated over a distribution of attainable reflection directions. We discovered the sensitivity of Aeolus lidar surface returns (LSR) to surface characteristics, providing the first evidence that active remote sensing can be effectively used for retrieving unidirectional UV surface reflectivity on global scales. LSR reproduces surface reflectivity monthly changes in Sahara, which are visible in the Lambertian Equivalent Reflectivity (LER) climatologies from TROPOMI and GOME-2. Very high correlations (r > 0.90) between gridded LSR and the LER climatologies are reported at global and regional scales for 36 different regions. Three clear land cover gradients are discerned from Aeolus LSR signal: (1) water/land, (2) vegetation/arid areas and (3) no snow/snow. The strongest LSR signal was retrieved over snow, while over vegetation, we found moderate negative agreement (r < − 0.60) between LSR and vegetation index proxy. Overall, the success of the first active remote sensing method for retrieving unidirectional UV surface reflectivity using Aeolus is demonstrated. Our approach can be effectively used to detect unresolved land and, especially, snow cover changes in high latitudes because, unlike passive instruments, Aeolus also provided nighttime observations.

An improved TROPOMI tropospheric NO&amp;lt;sub&amp;gt;2&amp;lt;/sub&amp;gt; research product over Europe

Abstract. Launched in October 2017, the TROPOspheric Monitoring Instrument (TROPOMI) aboard Sentinel-5 Precursor provides the potential to monitor air quality over point sources across the globe with a spatial resolution as high as 5.5 km × 3.5 km (7 km × 3.5 km before 6 August 2019). The DLR nitrogen dioxide (NO2) retrieval algorithm for the TROPOMI instrument consists of three steps: the spectral fitting of the slant column, the separation of stratospheric and tropospheric contributions, and the conversion of the slant column to a vertical column using an air mass factor (AMF) calculation. In this work, an improved DLR tropospheric NO2 retrieval algorithm from TROPOMI measurements over Europe is presented. The stratospheric estimation is implemented using the STRatospheric Estimation Algorithm from Mainz (STREAM), which was developed as a verification algorithm for TROPOMI and does not require chemistry transport model data as input. A directionally dependent STREAM (DSTREAM) is developed to correct for the dependency of the stratospheric NO2 on the viewing geometry by up to 2×1014 molec./cm2. Applied to synthetic TROPOMI data, the uncertainty in the stratospheric column is 3.5×1014 molec./cm2 in the case of significant tropospheric sources. Applied to actual measurements, the smooth variation of stratospheric NO2 at low latitudes is conserved, and stronger stratospheric variation at higher latitudes is captured. For AMF calculation, the climatological surface albedo data are replaced by geometry-dependent effective Lambertian equivalent reflectivity (GE_LER) obtained directly from TROPOMI measurements with a high spatial resolution. Mesoscale-resolution a priori NO2 profiles are obtained from the regional POLYPHEMUS/DLR chemistry transport model with the TNO-MACC emission inventory. Based on the latest TROPOMI operational cloud parameters, a more realistic cloud treatment is provided by a Clouds-As-Layers (CAL) model, which treats the clouds as uniform layers of water droplets, instead of the Clouds-As-Reflecting-Boundaries (CRB) model, in which clouds are simplified as Lambertian reflectors. For the error analysis, the tropospheric AMF uncertainty, which is the largest source of NO2 uncertainty for polluted scenarios, ranges between 20 % and 50 %, leading to a total uncertainty in the tropospheric NO2 column in the 30 %–60 % range. From a validation performed with ground-based multi-axis differential optical absorption spectroscopy (MAX-DOAS) measurements, the new DLR tropospheric NO2 data show good correlations for nine European urban/suburban stations, with an average correlation coefficient of 0.78. The implementation of the algorithm improvements leads to a decrease of the relative difference from −55.3 % to −34.7 % on average in comparison with the DLR reference retrieval. When the satellite averaging kernels are used to remove the contribution of a priori profile shape, the relative difference decreases further to ∼ −20 %.

First retrieval of absorbing aerosol height over dark target using TROPOMI oxygen B band: Algorithm development and application for surface particulate matter estimates

Constraint of the vertical distribution of aerosol particles is crucial for the study of aerosol plume structure, aerosol radiative effects, and ultimately monitoring surface air pollution. We developed an algorithm to retrieve the aerosol optical central height (AOCH) of absorbing aerosols by using, for the first time, the oxygen (O2) A and B absorption band measurements from the TROPOspheric Monitoring Instrument (TROPOMI) over dark targets. For the retrieval, narrow band radiance at seven channels ranging from ultraviolet (UV) to shortwave infrared (SWIR) are convolved from TROPOMI hyperspectral measurements. Subsequently, cloudy pixels are screened out by using the slope of spectral reflectance, while aerosol types (dust and smoke) are classified by the wavelength dependence of aerosol path radiance in conjunction with UV aerosol index. Surface reflectance over land is derived from the MODIS surface bi-directional reflectance climatology, and over water from the GOME-2 surface Lambert-equivalent reflectivity (LER) database. The aerosol optical depth (AOD) and AOCH are retrieved through an approach of look-up-table accounting for AERONET-based dust and smoke optical properties. For multiple smoke and dust plume events around the world, our retrieved AOCH values agree with space-borne lidar CALIOP counterparts, with a mean bias of <0.15 km and a correlation coefficient of 0.85–0.87. Due in part to adding the O2 B band, our retrieval represents an aerosol extinction peak height better than the TROPOMI operational Level 2 aerosol layer height retrieved from only the O2 A band. The latter shows 0.5–2 km low bias, especially over land. Finally, the high potential of AOCH for improving surface PM2.5 estimates is also illustrated with a case study in which the high bias of surface PM2.5 in MERRA-2 data is corrected after being scaled by the retrieved AOCH.

Rethinking the correction for absorbing aerosols in the OMI- and TROPOMI-like surface UV algorithms

Abstract. Satellite estimates of surface UV irradiance have been available since 1978 from the TOMS UV spectrometer and have continued with significantly improved ground resolution using the Ozone Monitoring Instrument (OMI 2004–current) and Sentinel 5 Precursor (S5P 2017–current). The surface UV retrieval algorithm remains essentially the same: it first estimates the clear-sky UV irradiance based on measured ozone and then accounts for the attenuation by clouds and aerosols, applying two consecutive correction factors. When estimating the total aerosol effect in surface UV irradiance, there are two major classes of aerosols to be considered: (1) aerosols that only scatter UV radiation and (2) aerosols that both scatter and absorb UV radiation. The former effect is implicitly included in the measured effective Lambertian-equivalent scene reflectivity (LER), so the scattering aerosol influence is estimated through cloud correction factor. Aerosols that absorb UV radiation attenuate the surface UV radiation more strongly than non-absorbing aerosols of the same extinction optical depth. Moreover, since these aerosols also attenuate the outgoing satellite-measured radiance, the cloud correction factor that treats these aerosols as purely scattering underestimates their aerosol optical depth (AOD), causing underestimation of LER and overestimation of surface UV irradiance. Therefore, for correction of aerosol absorption, additional information is needed, such as a model-based monthly climatology of aerosol absorption optical depth (AAOD). A correction for absorbing aerosols was proposed almost a decade ago and later implemented in the operational OMI and TROPOMI UV algorithms. In this study, however, we show that there is still room for improvement to better account for the solar zenith angle (SZA) dependence and nonlinearity in the absorbing aerosol attenuation, and as a result we propose an improved correction scheme. There are two main differences between the new proposed correction and the one that is currently operational in OMI and TROPOMI UV algorithms. First, the currently operational correction for absorbing aerosols is a function of AAOD only, while the new correction additionally takes the solar zenith angle dependence into account. Second, the second-order polynomial of the new correction takes the nonlinearity in the correction as a function of AAOD better into account, if compared to the currently operational one, and thus better describes the effect by absorbing aerosols over a larger range of AAOD. To illustrate the potential impact of the new correction in the global UV estimates, we applied the current and new proposed correction for global fields of AAOD from the aerosol climatology currently used in OMI UV algorithm, showing a typical differences of ±5 %. This new correction is easy to implement operationally using information of solar zenith angle and existing AAOD climatology.

Directionally dependent Lambertian-equivalent reflectivity (DLER) of the Earth's surface measured by the GOME-2 satellite instruments

Abstract. In this paper we introduce the new concept of directionally dependent Lambertian-equivalent reflectivity (DLER) of the Earth's surface retrieved from satellite observations. This surface DLER describes Lambertian (isotropic) surface reflection which is extended with a dependence on the satellite viewing geometry. We apply this concept to data of the GOME-2 satellite instruments to create a global database of the reflectivity of the Earth's surface, providing surface DLER for 26 wavelength bands between 328 and 772 nm as a function of the satellite viewing angle via a second-degree polynomial parameterisation. The resolution of the database grid is 0.25∘ by 0.25∘, but the real, intrinsic spatial resolution varies over the grid from 1.0∘ by 1.0∘ to 0.5∘ by 0.5∘ down to 0.25∘ by 0.25∘ by applying dynamic gridding techniques. The database is based on more than 10 years (2007–2018) of GOME-2 data from the MetOp-A and MetOp-B satellites. The relation between DLER and bi-directional reflectance distribution function (BRDF) surface reflectance is studied using radiative transfer simulations. For the shorter wavelengths (λ&lt;500 nm), there are significant differences between the two. For instance, at 463 nm the difference can go up to 6 % at 30∘ solar zenith angle. The study also shows that, although DLER and BRDF surface reflectances have different properties, they are comparable for the longer wavelengths (λ&gt;500 nm). Based on this outcome, the GOME-2 surface DLER is compared with MODIS surface BRDF data from MODIS band 1 (centred around 645 nm) using both case studies and global comparisons. The conclusion of this validation is that the GOME-2 DLER compares well to MODIS BRDF data and that it does so much better than the non-directional LER database. The DLER approach for describing surface reflectivity is therefore an important improvement over the standard isotropic (non-directional) LER approaches used in the past. The GOME-2 surface DLER database can be used for the retrieval of atmospheric properties from GOME-2 and from previous satellite instruments like GOME and SCIAMACHY. It will also be used to support retrievals from the future Sentinel-5 UVNS (ultraviolet, visible, near-infrared, and short-wave infrared) satellite instrument.

Explicit and consistent aerosol correction for visible wavelength satellite cloud and nitrogen dioxide retrievals based on optical properties from a global aerosol analysis

Abstract. We discuss an explicit and consistent aerosol correction for cloud and NO2 retrievals that are based on the mixed Lambertian-equivalent reflectivity (MLER) concept. We apply the approach to data from the Ozone Monitoring Instrument (OMI) for a case study over northeastern China. The cloud algorithm reports an effective cloud pressure, also known as cloud optical centroid pressure (OCP), from oxygen dimer (O2−O2) absorption at 477 nm after determining an effective cloud fraction (ECF) at 466 nm. The retrieved cloud products are then used as inputs to the standard OMI NO2 algorithm. A geometry-dependent Lambertian-equivalent reflectivity (GLER), which is a proxy of surface bidirectional reflectance, is used for the ground reflectivity in our implementation of the MLER approach. The current standard OMI cloud and NO2 algorithms implicitly account for aerosols by treating them as nonabsorbing particulate scatters within the cloud retrieval. To explicitly account for aerosol effects, we use a model of aerosol optical properties from a global aerosol assimilation system and radiative transfer computations. This approach allows us to account for aerosols within the OMI cloud and NO2 algorithms with relatively small changes. We compare the OMI cloud and NO2 retrievals with implicit and explicit aerosol corrections over our study area.

Ozone Monitoring Instrument (OMI) Aura nitrogen dioxide standard product version 4.0 with improved surface and cloud treatments

Abstract. We present a new and improved version (V4.0) of the NASA standard nitrogen dioxide (NO2) product from the Ozone Monitoring Instrument (OMI) on the Aura satellite. This version incorporates the most salient improvements for OMI NO2 products suggested by expert users and enhances the NO2 data quality in several ways through improvements to the air mass factors (AMFs) used in the retrieval algorithm. The algorithm is based on the geometry-dependent surface Lambertian equivalent reflectivity (GLER) operational product that is available on an OMI pixel basis. GLER is calculated using the vector linearized discrete ordinate radiative transfer (VLIDORT) model, which uses as input high-resolution bidirectional reflectance distribution function (BRDF) information from NASA's Aqua Moderate Resolution Imaging Spectroradiometer (MODIS) instruments over land and the wind-dependent Cox–Munk wave-facet slope distribution over water, the latter with a contribution from the water-leaving radiance. The GLER combined with consistently retrieved oxygen dimer (O2–O2) absorption-based effective cloud fraction (ECF) and optical centroid pressure (OCP) provide improved information to the new NO2 AMF calculations. The new AMFs increase the retrieved tropospheric NO2 by up to 50 % in highly polluted areas; these differences arise from both cloud and surface BRDF effects as well as biases between the new MODIS-based and previously used OMI-based climatological surface reflectance data sets. We quantitatively evaluate the new NO2 product using independent observations from ground-based and airborne instruments. The new V4.0 data and relevant explanatory documentation are publicly available from the NASA Goddard Earth Sciences Data and Information Services Center (https://disc.gsfc.nasa.gov/datasets/OMNO2_V003/summary/, last access: 8 November 2020), and we encourage their use over previous versions of OMI NO2 products.

In-orbit Earth reflectance validation of TROPOMI on board the Sentinel-5 Precursor satellite

Abstract. The goal of the study described in this paper is to determine the accuracy of the radiometric calibration of the TROPOMI instrument in flight, using its Earth radiance and solar irradiance measurements, from which the Earth reflectance is determined. The Earth reflectances are compared to radiative transfer calculations. We restrict ourselves to clear-sky observations as these are less difficult to model than observations containing clouds and/or aerosols. The limiting factor in the radiative transfer calculations is then the knowledge of the surface reflectance. We use OMI and SCIAMACHY surface Lambertian-equivalent reflectivity (LER) information to model the reflectivity of the Earth's surface. This Lambertian, nondirectional description of the surface reflection contribution results in a relatively large source of uncertainty in the calculations. These errors can be reduced significantly by filtering out geometries for which we know that surface LER is a poor approximation of the real surface reflectivity. This filtering is done by comparing the OMI/SCIAMACHY surface LER information to MODIS surface BRDF information. We report calibration accuracies and errors for 21 selected wavelength bands between 328 and 2314 nm, located in TROPOMI spectral bands 3–7. All wavelength bands show good linear response to the intensity of the radiation and negligible offset problems. Reflectances in spectral bands 5 and 6 (wavelength bands 670 to 772 nm) have good absolute agreement with the simulations, showing calibration errors on the order of 0.01 or 0 %–3 %. Trends over the mission lifetime, due to instrument degradation, are studied and found to be negligible at these wavelengths. Reflectances in bands 3 and 4 (wavelength bands 328 to 494 nm), on the other hand, are found to be affected by serious calibration errors, on the order of 0.004–0.02 and ranging between 6 % and 10 %, depending on the wavelength. The TROPOMI requirements (of 2 % maximal deviation) are not met in this case. Trends due to instrument degradation are also found, being strongest for the 328 nm wavelength band and almost absent for the 494 nm wavelength band. The validation results obtained for TROPOMI spectral band 7 show behaviour that we cannot fully explain. As a result, these results call for more research and different methods to study the calibration of the reflectance. It seems plausible, though, that the reflectance for this particular band is underestimated by about 6 %. A table is provided containing the final results for all 21 selected wavelength bands.

Applying FP_ILM to the retrieval of geometry-dependent effective Lambertian equivalent reflectivity (GE_LER) daily maps from UVN satellite measurements

Abstract. The retrieval of trace gas, cloud, and aerosol measurements from ultraviolet, visible, and near-infrared (UVN) sensors requires precise information on surface properties that are traditionally obtained from Lambertian equivalent reflectivity (LER) climatologies. The main drawbacks of using LER climatologies for new satellite missions are that (a) climatologies are typically based on previous missions with significantly lower spatial resolutions, (b) they usually do not account fully for satellite-viewing geometry dependencies characterized by bidirectional reflectance distribution function (BRDF) effects, and (c) climatologies may differ considerably from the actual surface conditions especially with snow/ice scenarios. In this paper we present a novel algorithm for the retrieval of geometry-dependent effective Lambertian equivalent reflectivity (GE_LER) from UVN sensors; the algorithm is based on the full-physics inverse learning machine (FP_ILM) retrieval. Radiances are simulated using a radiative transfer model that takes into account the satellite-viewing geometry, and the inverse problem is solved using machine learning techniques to obtain the GE_LER from satellite measurements. The GE_LER retrieval is optimized not only for trace gas retrievals employing the DOAS algorithm, but also for the large amount of data from existing and future atmospheric Sentinel satellite missions. The GE_LER can either be deployed directly for the computation of air mass factors (AMFs) using the effective scene approximation or it can be used to create a global gapless geometry-dependent LER (G3_LER) daily map from the GE_LER under clear-sky conditions for the computation of AMFs using the independent pixel approximation. The GE_LER algorithm is applied to measurements of TROPOMI launched in October 2017 on board the EU/ESA Sentinel-5 Precursor (S5P) mission. The TROPOMI GE_LER/G3_LER results are compared with climatological OMI and GOME-2 LER datasets and the advantages of using GE_LER/G3_LER are demonstrated for the retrieval of total ozone from TROPOMI.

An improved air mass factor calculation for nitrogen dioxide measurements from the Global Ozone Monitoring Experiment-2 (GOME-2)

Abstract. An improved tropospheric nitrogen dioxide (NO2) retrieval algorithm from the Global Ozone Monitoring Experiment-2 (GOME-2) instrument based on air mass factor (AMF) calculations performed with more realistic model parameters is presented. The viewing angle dependency of surface albedo is taken into account by improving the GOME-2 Lambertian-equivalent reflectivity (LER) climatology with a directionally dependent LER (DLER) dataset over land and an ocean surface albedo parameterisation over water. A priori NO2 profiles with higher spatial and temporal resolutions are obtained from the IFS (CB05BASCOE) chemistry transport model based on recent emission inventories. A more realistic cloud treatment is provided by a clouds-as-layers (CAL) approach, which treats the clouds as uniform layers of water droplets, instead of the current clouds-as-reflecting-boundaries (CRB) model, which assumes that the clouds are Lambertian reflectors. On average, improvements in the AMF calculation affect the tropospheric NO2 columns by ±15 % in winter and ±5 % in summer over largely polluted regions. In addition, the impact of aerosols on our tropospheric NO2 retrieval is investigated by comparing the concurrent retrievals based on ground-based aerosol measurements (explicit aerosol correction) and the aerosol-induced cloud parameters (implicit aerosol correction). Compared with the implicit aerosol correction utilising the CRB cloud parameters, the use of the CAL approach reduces the AMF errors by more than 10 %. Finally, to evaluate the improved GOME-2 tropospheric NO2 columns, a validation is performed using ground-based multi-axis differential optical absorption spectroscopy (MAXDOAS) measurements at different BIRA-IASB stations. At the suburban Xianghe station, the improved tropospheric NO2 dataset shows better agreement with coincident ground-based measurements with a correlation coefficient of 0.94.

A geometry-dependent surface Lambertian-equivalent reflectivity product for UV–Vis retrievals – Part 2: Evaluation over open ocean

Abstract. Satellite-based cloud, aerosol, and trace-gas retrievals from ultraviolet (UV) and visible (Vis) wavelengths depend on the accurate representation of surface reflectivity. Current UV and Vis retrieval algorithms typically use surface reflectivity climatologies that do not account for variation in satellite viewing geometry or surface roughness. The concept of geometry-dependent surface Lambertian-equivalent reflectivity (GLER) is implemented for water surfaces to account for surface anisotropy using a Case 1 water optical model and the Cox–Munk slope distribution for ocean surface roughness. GLER is compared with Lambertian-Equivalent reflectivity (LER) derived from the Ozone Monitoring Instrument (OMI) for clear scenes at 354, 388, 440, and 466 nm. We show that GLER compares well with the measured LER data over the open ocean and captures the directionality effects not accounted for in climatological LER databases. Small biases are seen when GLER and the OMI-derived LER are compared. GLER is biased low by up to 0.01–0.02 at Vis wavelengths and biased high by around 0.01 in the UV, particularly at 354 nm. Our evaluation shows that GLER is an improvement upon climatological LER databases as it compares well with OMI measurements and captures the directionality effects of surface reflectance.

UV Reflectance of the Ocean from DSCOVR/EPIC: Comparisons with a Theoretical Model and Aura/OMI Observations

AbstractUltraviolet (UV) data collected over the ocean by the Earth Polychromatic Imaging Camera (EPIC) on theDeep Space Climate Observatory(DSCOVR) are used. The Multi-Angle Implementation of Atmospheric Correction (MAIAC) algorithm adapted for EPIC processing performs cloud detection, aerosol retrievals, and atmospheric correction providing the water-leaving reflectance of the ocean at 340 and 388 nm. The water-leaving reflectance is an indicator of the presence of absorbing and scattering constituents in seawater. The retrieved water-leaving reflectance is compared with full radiative transfer calculations based on a model of inherent optical properties (IOP) of ocean water in UV. The model is verified with data collected on the Aerosol Characterization Experiments (ACE) Asia cruise supported by the NASA Sensor Intercomparison for Marine Biological and Interdisciplinary Ocean Studies (SIMBIOS) project. The model assumes that the ocean water IOPs are parameterized through a chlorophyll concentration. The radiative transfer simulations were carried out using the climatological chlorophyll concentration from the Moderate Resolution Imaging Spectroradiometer (MODIS) on board theAquasatellite. The EPIC-derived water-leaving reflectance is also compared with climatological Lambertian-equivalent reflectivity (LER) of the ocean derived from measurements of the Ozone Monitoring Instrument (OMI) on board the NASA polar-orbitingAurasatellite. The EPIC reflectance agrees well (within 0.01) with the model reflectance except for oligotrophic oceanic areas. For those areas, the model reflectance is biased low by about 0.01 at 340 nm and up to 0.03 at 388 nm. The OMI-derived climatological LER is significantly higher than the EPIC water-leaving reflectance, largely due to the surface glint contribution. The globally averaged difference is about 0.04.

A geometry-dependent surface Lambertian-equivalent reflectivity product for UV–Vis retrievals – Part 1: Evaluation over land surfaces using measurements from OMI at 466 nm

Abstract. The anisotropy of the Earth's surface reflection has implications for satellite-based retrieval algorithms that utilize climatological surface reflectivity databases that do not depend upon the observation geometry. This is the case for most of the current ultraviolet and visible (UV–Vis) cloud, aerosol, and trace-gas algorithms. The illumination–observation dependence of surface reflection is described by the bidirectional reflectance distribution function (BRDF). To account for the BRDF effect, we use the concept of geometry-dependent surface Lambertian-equivalent reflectivity (GLER), which is derived from the top-of-atmosphere (TOA) radiance computed with Rayleigh scattering and surface BRDF for the exact geometry of a satellite-based pixel. We present details on the implementation of land and water surface BRDF models, and we evaluate our GLER product over land surfaces using observed Sun-normalized radiances at 466 nm. The input surface BRDF parameters for computing TOA radiance are derived from Moderate Resolution Imaging Spectroradiometer (MODIS) satellite observations. The observed TOA radiance for comparison is from the Ozone Monitoring Instrument (OMI). The comparison shows good agreement between observed and calculated OMI reflectivity in 2006 in typical geographical regions, with correlation coefficients greater than 0.8 for some regions. Seasonal variations of clear-sky OMI reflectivity (i.e., with minimum clouds and aerosols) closely follow those computed using MODIS-derived GLER over land. GLER also captures the cross-track dependence of OMI-derived LER, though the latter is slightly higher than the former presumably owing to residual cloud and aerosol (nonabsorbing) contamination, particularly over dark surfaces (heavily vegetated regions such as mixed forest, croplands, and grasslands). Calibration differences between OMI and MODIS may also be responsible for some of this bias. The standard OMI climatological surface reflectivity database predicts higher radiances than GLER and OMI observations with different seasonal variation over most regions and does not have any angular-dependent variation. Overall, our evaluation demonstrates that the GLER product adequately accounts for surface BRDF effects while at the same time simplifying the surface BRDF implementation within the existing OMI retrieval infrastructure; use of our GLER product requires changes only to the input surface reflectivity database.

A cloud algorithm based on the O&amp;lt;sub&amp;gt;2&amp;lt;/sub&amp;gt;-O&amp;lt;sub&amp;gt;2&amp;lt;/sub&amp;gt; 477 nm absorption band featuring an advanced spectral fitting method and the use of surface geometry-dependent Lambertian-equivalent reflectivity

Abstract. We discuss a new cloud algorithm that retrieves an effective cloud pressure, also known as cloud optical centroid pressure (OCP), from oxygen dimer (O2-O2) absorption at 477 nm after determining an effective cloud fraction (ECF) at 466 nm, a wavelength not significantly affected by trace-gas absorption and rotational Raman scattering. The retrieved cloud products are intended for use as inputs to the operational nitrogen dioxide (NO2) retrieval algorithm for the Ozone Monitoring Instrument (OMI) flying on the Aura satellite. The cloud algorithm uses temperature-dependent O2-O2 cross sections and incorporates flexible spectral fitting techniques that account for specifics of the surface reflectivity. The fitting procedure derives O2-O2 slant column densities (SCDs) from radiances after O3, NO2, and H2O absorption features have been removed based on estimates of the amounts of these species from independent OMI algorithms. The cloud algorithm is based on the frequently used mixed Lambertian-equivalent reflectivity (MLER) concept. A geometry-dependent Lambertian-equivalent reflectivity (GLER), which is a proxy of surface bidirectional reflectance, is used for the ground reflectivity in our implementation of the MLER approach. The OCP is derived from a match of the measured O2-O2 SCD to that calculated with the MLER method. Temperature profiles needed for computation of vertical column densities are taken from the Global Modeling Initiative (GMI) model. We investigate the effect of using GLER instead of climatological LER on the retrieved ECF and OCP. For evaluation purposes, the retrieved ECFs and OCPs are compared with those from the operational OMI cloud product, which is also based on the same O2-O2 absorption band. Impacts of the application of the newly developed cloud algorithm to the OMI NO2 retrieval are discussed.

Synoptic ozone, cloud reflectivity, and erythemal irradiance from sunrise to sunset for the whole earth as viewed by the DSCOVR spacecraft from the earth–sun Lagrange 1 orbit

Abstract. EPIC (Earth Polychromatic Imaging Camera) on board the DSCOVR (Deep Space Climate Observatory) spacecraft is the first earth science instrument located near the earth–sun gravitational plus centrifugal force balance point, Lagrange 1. EPIC measures earth-reflected radiances in 10 wavelength channels ranging from 317.5 to 779.5 nm. Of these channels, four are in the UV range 317.5, 325, 340, and 388 nm, which are used to retrieve O3, 388 nm scene reflectivity (LER: Lambert equivalent reflectivity), SO2, and aerosol properties. These new synoptic quantities are retrieved for the entire sunlit globe from sunrise to sunset multiple times per day as the earth rotates in EPIC's field of view. Retrieved ozone amounts agree with ground-based measurements and satellite data to within 3 %. The ozone amounts and LER are combined to derive the erythemal irradiance for the earth's entire sunlit surface at a nadir resolution of 18 × 18 km2 using a computationally efficient approximation to a radiative transfer calculation of irradiance. The results show very high summertime values of the UV index (UVI) in the Andes and Himalayas (greater than 18), and high values of UVI near the Equator at equinox.

A seasonal climatology of UV reflectivity for southern South America

ABSTRACTA seasonal climatology for the Lambertian equivalent reflectivity (LER) in ultraviolet (UV) for southern South America is introduced. The study region was limited by 10° and 60°S and by 100° and 30°W; the data set spanned the period 1978–2015. Features of the seasonal means and of the quarterly (Q) and the interannual (IA) variabilities for each season were ascribed to atmospheric and oceanic processes of local, regional, or global origin which lead to the formation or maintenance of clouds. Shifts in the Q and IA time series were detected, most notably in the early 1990s. Linear trends were also estimated. The largest positive and negative trends in the Q time series were found along the Peruvian Andes (PA) (3.20 reflectivity units [RU] decade−1) and east of the Chapada Diamantina (CD) and the Serra do Espinhaço (SE) in Brazil (−1.40 RU decade−1), respectively. The largest positive and negative trends in the IA time series were found in PA (6 RU decade−1, summer) and east of CD and SE (−2.50 RU decade−1, spring), respectively. The linkages between UV LER and regional or global circulation indices were also studied. The largest relationships were found with the Dipole Mode Index on a Q basis and with the Southern Oscillation Index on an IA basis in winter.

Surface reflectivity climatologies from UV to NIR determined from Earth observations by GOME‐2 and SCIAMACHY

AbstractThe primary goal of this paper is to introduce two new surface reflectivity climatologies. The two databases contain the Lambertian‐equivalent reflectivity (LER) of the Earth's surface, and they are meant to support satellite retrieval of trace gases and of cloud and aerosol information. The surface LER databases are derived from the Global Ozone Monitoring Experiment (GOME)‐2 and Scanning Imaging Absorption Spectrometer for Atmospheric Chartography (SCIAMACHY) instruments and can be considered as improved and extended descendants of earlier surface LER climatologies based on the Total Ozone Mapping Spectrometer (TOMS), GOME‐1, and Ozone Monitoring Instrument (OMI) instruments. The GOME‐2 surface LER database consists of 21 wavelength bands that span the wavelength range from 335 to 772 nm. The SCIAMACHY surface LER database covers the wavelength range between 335 and 1670 nm in 29 wavelength bands. The two databases are made for each month of the year, and their spatial resolution is 1° × 1°. In this paper we present the methods that are used to derive the surface LER; we analyze the spatial and temporal behavior of the surface LER fields and study the amount of residual cloud contamination in the databases. For several surface types we analyze the spectral surface albedo and the seasonal variation. When compared to the existing surface LER databases, both databases are found to perform well. As an example of possible application of the databases we study the performance of the Fast Retrieval Scheme for Clouds from the Oxygen A‐band (FRESCO) cloud information retrieval when it is equipped with the new surface albedo databases. We find considerable improvements. The databases introduced here can not only improve retrievals from GOME‐2 and SCIAMACHY but also support those from other instruments, such as TROPOspheric Monitoring Instrument (TROPOMI), to be launched in 2017.

Annual anomalies and trends for TOMS reflectivities (1978–2005) in the Southern Hemisphere

ABSTRACTAnnual anomalies of Lambertian equivalent reflectivity (LER) retrieved from the total ozone mapping spectrometer spanning the period November 1978–November 2005 were studied in the Southern Hemisphere, in a region bounded by 0° S and 60° S, and their trends were estimated. With the exception of few regions where the variable may represent the contribution of both cloudiness and snow, trends in LER anomalies provided an evolution of total cloudiness. On average, the study region experienced a net increase in LER values of 0.78 reflectivity units (RU) decade−1; if only significant trend values are considered this figure increased to 1.18 RU decade−1. The region that showed the largest upward trend, up to 4 RU decade−1, was located over the eastern Pacific, off the coasts of Chile and Peru, where the presence of marine stratocumulus is frequent. Despite the overall positive trend there were regions that yielded a negative one, most notably the tropical latitudes of South America and Africa. The yearly zonal means also showed a positive trend at all latitudes, but significance occurred beyond 20° S only. Correlation maps between LER anomalies and five different circulation indices were also introduced. The indices with the highest and lowest number of significant correlation values were the Madden–Julian oscillation at 70° E and the quasi-biennial Oscillation, respectively.

New-generation NASA Aura Ozone Monitoring Instrument (OMI) volcanic SO&amp;lt;sub&amp;gt;2&amp;lt;/sub&amp;gt; dataset: algorithm description, initial results, and continuation with the Suomi-NPP Ozone Mapping and Profiler Suite (OMPS)

Abstract. Since the fall of 2004, the Ozone Monitoring Instrument (OMI) has been providing global monitoring of volcanic SO2 emissions, helping to understand their climate impacts and to mitigate aviation hazards. Here we introduce a new-generation OMI volcanic SO2 dataset based on a principal component analysis (PCA) retrieval technique. To reduce retrieval noise and artifacts as seen in the current operational linear fit (LF) algorithm, the new algorithm, OMSO2VOLCANO, uses characteristic features extracted directly from OMI radiances in the spectral fitting, thereby helping to minimize interferences from various geophysical processes (e.g., O3 absorption) and measurement details (e.g., wavelength shift). To solve the problem of low bias for large SO2 total columns in the LF product, the OMSO2VOLCANO algorithm employs a table lookup approach to estimate SO2 Jacobians (i.e., the instrument sensitivity to a perturbation in the SO2 column amount) and iteratively adjusts the spectral fitting window to exclude shorter wavelengths where the SO2 absorption signals are saturated. To first order, the effects of clouds and aerosols are accounted for using a simple Lambertian equivalent reflectivity approach. As with the LF algorithm, OMSO2VOLCANO provides total column retrievals based on a set of predefined SO2 profiles from the lower troposphere to the lower stratosphere, including a new profile peaked at 13 km for plumes in the upper troposphere. Examples given in this study indicate that the new dataset shows significant improvement over the LF product, with at least 50 % reduction in retrieval noise over the remote Pacific. For large eruptions such as Kasatochi in 2008 (∼ 1700 kt total SO2) and Sierra Negra in 2005 (&gt; 1100 DU maximum SO2), OMSO2VOLCANO generally agrees well with other algorithms that also utilize the full spectral content of satellite measurements, while the LF algorithm tends to underestimate SO2. We also demonstrate that, despite the coarser spatial and spectral resolution of the Suomi National Polar-orbiting Partnership (Suomi-NPP) Ozone Mapping and Profiler Suite (OMPS) instrument, application of the new PCA algorithm to OMPS data produces highly consistent retrievals between OMI and OMPS. The new PCA algorithm is therefore capable of continuing the volcanic SO2 data record well into the future using current and future hyperspectral UV satellite instruments.