Kinetic Inductance Research Articles

Initial Design of a W-Band Superconducting Kinetic Inductance Qubit

Superconducting qubits are widely used in quantum computing research and industry. We describe a superconducting kinetic inductance qubit (and introduce the term Kineticon to describe it) operating at W-band frequencies with a nonlinear nanowire section that provides the anharmonicity required for two distinct quantum energy states. Operating the qubits at higher frequencies may relax the dilution refrigerator temperature requirements for these devices and paves the path for multiplexing a large number of qubits. Millimeter-wave operation requires superconductors with relatively high $T_c$, which implies high gap frequency, 2$\Delta/h$, beyond which photons break Cooper pairs. For example, NbTiN with $T_c =15\,\text{K}$ has a gap frequency near 1.4 THz, which is much higher than that of aluminum (90 GHz), allowing for operation throughout the millimeter-wave band. Here we describe a design and simulation of a W-band Kineticon qubit embedded in a 3-D cavity. We perform classical electromagnetic calculations of the resulting field distributions.

Synchronous SFQ Address Encoder for Superconductor Detector Arrays

With the advances in superconductor detectors and single flux quantum (SFQ) logic circuits, megapixel imagers have become possible. Various detectors such as superconducting stripline detectors (SSLD), kinetic inductance detectors, nanowire single-photon detectors have quite matured in terms of speed and performance. However, scaling of the read-out electronics is still a challenge. We propose an SFQ based synchronous address encoder to read-out the response of an SSLD array. The encoder circuit provides two sets of outputs at each clock period: one is the time-division multiplexed, serial data output, and the other is the synchronized address output associated with the time-multiplexed data. Thus, the number of connections to the room temperature is substantially reduced. We experimentally demonstrate a 2-bit encoder. Then, we present the scalability of the circuit to larger arrays and show the simulation results of a 4-bit encoder, which is suitable to read-out a 16 × 16 detector array.

Tilapia dsRNA-activated protein kinase R (PKR): An interferon-induced antiviral effector with translation inhibition activity

The dsRNA-activated protein kinase R (PKR) is one of key antiviral effectors induced by interferons (IFNs), and its functions are largely unknown in tilapia, an important commercial fish species suffering from several viral infectious diseases. In the present study, a PKR gene named On-PKR was identified and cloned from Nile tilapia, Oreochromis niloticus. On-PKR gene was constitutively expressed in all tissues examined, with the highest expression level observed in head kidney and liver, and was rapidly induced in all organs/tissues tested following the stimulation of poly(I:C). Importantly, the expression of On-PKR is induced by group I and group II IFNs with distinct induction kinetics in vivo: group I IFN elicits a relative delayed but sustained induction of On-PKR, whereas group II IFN triggers a rapid and transient expression of On-PKR. Moreover, the overexpression of On-PKR has been proven to inhibit the protein translation and virus replication in fish cells. The present study thus contributes to a better understanding of the functions of antiviral effectors in tilapia, and may provide clues for the prevention and therapy of viral diseases in fish.

Compact and Tunable Forward Coupler Based on High-Impedance Superconducting Nanowires

Developing compact, low-dissipation, cryogenic-compatible microwave electronics is essential for scaling up low-temperature quantum computing systems. In this paper, we demonstrate an ultracompact microwave directional forward coupler based on high-impedance slow-wave superconducting-nanowire transmission lines. The coupling section of the fabricated device has a footprint of $416\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}{\mathrm{m}}^{2}$. At 4.753 GHz, the input signal couples equally to the through port and forward-coupling port (50:50) at $\ensuremath{-}6.7\phantom{\rule{0.2em}{0ex}}\mathrm{dB}$ with $\ensuremath{-}13.5\phantom{\rule{0.2em}{0ex}}\mathrm{dB}$ isolation. The coupling ratio can be controlled with dc bias current or temperature by exploiting the dependence of the kinetic inductance on these quantities. The material and fabrication processes are suitable for direct integration with superconducting circuits, providing a practical solution to the signal distribution bottlenecks in developing large-scale quantum computers.

Protein Phosphatase 2A Catalytic Subunit PP2A-1 Enhances Rice Resistance to Sheath Blight Disease.

Rice (Oryza sativa) production is damaged to a great extent by sheath blight disease (ShB). However, the defense mechanism in rice against this disease is largely unknown. Previous transcriptome analysis identified a significantly induced eukaryotic protein phosphatase 2A catalytic subunit 1 (PP2A-1) after the inoculation of Rhizoctonia solani. Five genes encoding PP2A exist in rice genome, and these five genes are ubiquitously expressed in different tissues and stages. Inoculation of R. solani showed that the genome edited pp2a-1 mutants using the CRISPR/Cas9 were more susceptible to ShB than the wild-type control, but other PP2A gene mutants exhibited similar response to ShB compared to wild-type plants. In parallel, PP2A-1 expression level was higher in the activation tagging line, and PP2A-1 overexpression inhibited plant height and promoted the resistance to ShB. PP2A-1-GFP was localized in the cytoplasm and nucleus. In addition, R. solani-dependent induction kinetics of pathogen-related genes PBZ1 and PR1b was lower in pp2a-1 mutants but higher in PP2A-1 activation line compared to those in the wild-type. In conclusion, our analysis shows that PP2A-1 is a member of protein phosphatase, which regulates rice resistance to ShB. This result broadens the understanding of the defense mechanism against ShB and provides a potential target for rice breeding for disease resistance.

Low kinetic inductance superconducting MgB2 nanowires with a 130 ps relaxation time for single-photon detection applications

Properties of superconducting nanowires set the performance level for superconducting nanowire single photon detectors (SNSPDs). Reset time in commonly employed large area SNSPDs, 1–10 ns, is known to be limited by the nanowire’s kinetic inductance to the load impedance ratio. On the other hand, reduction of the kinetic inductance in small area (waveguide integrated) SNSPDs prevents biasing them close to the critical current due to latching into a permanent resistive state. In order to reduce the reset time in SNSPDs, superconducting nanowires with both low kinetic inductance and fast electron energy relaxation are required. In this paper, we report on a study of kinetic inductance in narrow (15–100 nm) and long (up to 120 μm) superconducting MgB2 nanowires made from 5 nm thick films, offering such combination of properties. Such films were grown using hybrid physical chemical vapor deposition, resulting in a critical temperature of ∼32 K, and a switch current density of 5 × 107 A cm−2 (at 4.8 K). Using microwave reflectometry, we measured a kinetic inductance of L k0(4.8 K) = 1.3–1.6 pH/□ regardless of the nanowire width, which results in a magnetic field penetration depth of ∼90 nm. These values are very close to those in pristine MgB2. We showed that after excitations by a 50 fs pulsed laser the reset time in 35 nm × 120 μm MgB2 nanowires is 130 ps, which is more than a factor of 10 shorter than in NbN nanowires of similar length-to-width ratios. Depending on the bias current, such MgB2 nanowires function as single-, double, or triple-photon detectors for both visible (λ = 630 nm) and infrared (λ = 1550 nm) photons, with a dark count rate of <10 cps. Although the apparent photon detection efficiency seems so far to be low, further technological advances (uniform nanowire width, smaller thickness, increasing the switching current closer to the pair-breaking current) may improve this figure of merit.

High Mobility 3D Dirac Semimetal (Cd3As2) for Ultrafast Photoactive Terahertz Photonics

AbstractThe Dirac semimetal cadmium arsenide (Cd3As2), a 3D electronic analog of graphene, has sparked renewed research interests for its novel topological phases and excellent optoelectronic properties. The gapless nature of its 3D electronic band facilitates strong optical nonlinearity and supports Dirac plasmons that are of particular interest to realize high‐performance electronic and photonic devices at terahertz (1 THz = 4.1 meV) frequencies, where the performance of most dynamic materials are limited by the tradeoff between power‐efficiency and switching speed. Here, all‐optical, low‐power, ultrafast broadband modulation of terahertz waves using an ultrathin film (100 nm, λ/3000) of Cd3As2 are experimentally demonstrated through active tailoring of the photoconductivity. The measurements reveal the photosensitive metallic behavior of Cd3As2 with high terahertz electron mobility of 7200 cm2 (Vs)−1. In addition, optical fluence dependent ultrafast charge carrier relaxation (15.5 ps), terahertz mobility, and long momentum scattering time (157 fs) comparable to superconductors that invoke kinetic inductance at terahertz frequencies are demonstrated. These remarkable properties of 3D Dirac topological semimetal envision a new class of power‐efficient, high speed, compact, tunable electronic, and photonic devices.

Laminarin Induces Defense Responses and Efficiently Controls Olive Leaf Spot Disease in Olive.

Olive leaf spot (OLS) caused by Fusicladium oleagineum is mainly controlled using copper fungicides. However, the replacement of copper-based products with eco-friendly alternatives is a priority. The use of plant resistance-inducers (PRIs) or biological control agents (BCAs) could contribute in this direction. In this study we investigated the potential use of three PRIs (laminarin, acibenzolar-S-methyl, harpin) and a BCA (Bacillus amyloliquefaciens FZB24) for the management of OLS. The tested products provided control efficacy higher than 68%. In most cases, dual applications provided higher (p < 0.05) control efficacies compared to that achieved by single applications. The highest control efficacy of 100% was achieved by laminarin. Expression analysis of the selected genes by RT-qPCR revealed different kinetics of induction. In laminarin-treated plants, for most of the tested genes a higher induction rate (p < 0.05) was observed at 3 days post application. Pal, Lox, Cuao and Mpol were the genes with the higher inductions in laminarin-treated and artificially inoculated plants. The results of this study are expected to contribute towards a better understanding of PRIs in olive culture and the optimization of OLS control, while they provide evidence for potential contributions in the reduction of copper accumulation in the environment.

Ameliorating Effect of Bicarbonate on Salinity Induced Changes in the Growth, Nutrient Status, Cell Constituents and Photosynthetic Attributes of Microalga Chlorella vulgaris

The cells of Chlorella vulgaris exhibited NaCl (0-400mM) induced decrease in the growth, protein, chlorophyll, carbohydrate and total organic carbon, whereas total lipid and proline content increased with rising level of NaCl. Addition of NaHCO3 (20mM) exhibited antagonistic effect against the adverse effect of salinity on the growth, level of macromolecules except proline. The SEM-EDS analysis of NaCl treated cells exhibited morphological variations as well as reduced accumulation of Na and Cl due to the presence of NaHCO3. The results on chlorophyll fluorescence induction kinetics revealed NaCl induced decline in the photosynthetic performance and quantum yield, while non-photochemical quenching of chlorophyll was enhanced, particularly at lower concentrations of NaCl. Addition of NaHCO3 to NaCl treated cells exhibited further increase in the non-photochemical quenching values. Thus, these results demonstrated that adverse impact of NaCl on the C. vulgaris cells was significantly mitigated in the presence of bicarbonate.

Photosynthetic efficiency and compositional alterations in microalgae Chlorella vulgaris in response to changes in the pH condition

Present investigation on the effect of varying extracellular pH conditions (pH 6.5–10.5) on growth, accumulation of cell constituents and photosynthetic performance of microalga Chlorella vulgaris revealed that slightly alkaline pH (7.5–8.5) was the preferred pH range for growth, synthesis of protein and carbohydrate. Whereas total organic carbon (TOC) and lipid content in the microalga gradually increased with pH ranging ranging from 6.5 to 10.5. The FTIR results on total lipid (1740 cm− 1), lipid/carbohydrate (1740/1650 cm− 1) and lipid/protein (1740/1040 cm− 1) ratio in the cells grown at pH 6.5, 8.5 and 10.5 supported the above observation on the estimated amount of macromolecules. The chlorophyll fluorescence induction kinetics (OJIP), exhibiting various photosynthetic parameters, showed initial improvement in the photosynthetic efficiency between pH 6.5–8.5, followed by pH dependent declining pattern. Addition of HCO3− (20 mM) showed little effect on the photosynthetic electron transport. The energy dependent quenching parameters of chlorophyll fluorescence like ABS/RC, NPQ and qE, usually associated with the energy state of the membrane, registered an increasing trend with rising pH (pH 6.5–10.5). Use of energy inhibitors DNP, CCCP and electron acceptors/donors (methyl viologen and phenazine methosulphate) on ABS/RC, NPQ and qE suggested that pH dependent regulation of photosynthetic performance in C. vulgaris was tightly coupled with proton gradient of the membrane and that was reversed by the energy uncouplers like DNP and CCCP or electron acceptor like MV.

A chemically etched corrugated feedhorn array for D-band CMB observations

We present the design, manufacturing, and testing of a 37-element array of corrugated feedhorns for Cosmic Microwave Background CMB) measurements between 140 and 170 GHz. The array was designed to be coupled to Kinetic Inductance Detector arrays, either directly (for total power measurements) or through an orthomode transducer (for polarization measurements). We manufactured the array in platelets by chemically etching aluminum plates of 0.3 mm and 0.4 mm thickness. The process is fast, low-cost, scalable, and yields high-performance antennas compared to other techniques in the same frequency range. Room temperature electromagnetic measurements show excellent repeatability with an average cross polarization level about − 20 dB, return loss about − 25 dB, first sidelobes below − 25 dB and far sidelobes below − 35 dB. Our results qualify this process as a valid candidate for state-of-the-art CMB experiments, where large detector arrays with high sensitivity and polarization purity are of paramount importance in the quest for the discovery of CMB polarization B-modes.

Improving the dynamic range of single photon counting kinetic inductance detectors

We develop a simple coordinate transformation which can be employed to compensate for the nonlinearity introduced by a Microwave Kinetic Inductance Detector's (MKID) homodyne readout scheme. This coordinate system is compared to the canonically used polar coordinates and is shown to improve the performance of the filtering method often used to estimate a photon's energy. For a detector where the coordinate nonlinearity is primarily responsible for limiting its resolving power, this technique leads to increased dynamic range, which we show by applying the transformation to data from a hafnium MKID designed to be sensitive to photons with wavelengths in the 800 to 1300 nm range. The new coordinates allow the detector to resolve photons with wavelengths down to 400 nm, raising the resolving power at that wavelength from 6.8 to 17.

Development of an Array of Kinetic Inductance Magnetometers (KIMs)

We describe optimization of a cryogenic magnetometer that uses nonlinear kinetic inductance in superconducting nanowires as the sensitive element instead of a superconducting quantum interference device (SQUID). The circuit design consists of a loop geometry with two nanowires in parallel, serving as the inductive section of a lumped LC resonator similar to a kinetic inductance detector (KID). This device takes advantage of the multiplexing capability of the KID, allowing for a natural frequency multiplexed readout. The Kinetic Inductance Magnetometer (KIM) is biased with a DC magnetic flux through the inductive loop. A perturbing signal will cause a flux change through the loop, and thus a change in the induced current, which alters the kinetic inductance of the nanowires, causing the resonant frequency of the KIM to shift. This technology has applications in astrophysics, material science, and the medical field for readout of Metallic Magnetic Calorimeters (MMCs), axion detection, and magnetoencephalography (MEG).

Waveform analysis of a large-area superconducting nanowire single photon detector

Superconducting nanowire single photon detectors (SNSPDs) are typically used as single-mode-fiber-coupled single-pixel detectors, but large area detectors are increasingly critical for applications ranging from microscopy to free-space quantum communications. However, the long meander-line length of such large-area SNSPDs results in a proportionately large kinetic inductance that affects the waveform generated by the device. Here, we explore changes in the rising edge of the readout pulse for a single-pixel large-area SNSPD as a function of the optical spot size on the detector and compare to the rising edge of the dark-count waveform. We observe a bimodal distribution of bright-count rise times and show that the probability of a slow rise time increases in the limit of large spot sizes, indicative of a position sensitive response. Additionally, in the limit of low bias currents, the dark-count readout pulse is most similar to the large spot-size bright-count readout pulse, which suggests that dark counts arise from locations spanning the device. These results are consistent with a simple model of traveling microwave modes excited by single photons incident at varying positions along the length of the nanowire.

Magnetic field resilient high kinetic inductance superconducting niobium nitride coplanar waveguide resonators

We characterize niobium nitride (NbN) λ/2 coplanar waveguide resonators, which were fabricated from a 10-nm-thick film on silicon dioxide grown by sputter deposition. For films grown at 180 °C, we report a superconducting critical temperature of 7.4 K associated with a normal square resistance of 1 kΩ, leading to a kinetic inductance of 192 pH/◻. We fabricated resonators with a characteristic impedance up to 4.1 kΩ and internal quality factors Qi&amp;gt;104 in the single photon regime at zero magnetic field. Moreover, in the many photon regime, the resonators present a high magnetic field resilience with Qi&amp;gt;104 in a 6 T in-plane magnetic field and in a 300 mT out-of-plane magnetic field. These findings make such resonators a compelling choice for circuit quantum electrodynamics experiments involving quantum systems with small electric dipole moments operated in finite magnetic fields.

Oversampled filter bank channelizer for cryogenic detectors.

We present the field-programmable gate array (FPGA) implementation of an oversampled generalized discrete Fourier transform (GDFT) filter bank (FB), optimized for its usage in the readout of cryogenic detectors, such as microwave kinetic inductance detectors. A polyphase structure is derived underlining the efficiency of complex-valued subband processing, raised by a GDFT modulation. For the latter, a fast Fourier algorithm realization may be used, yielding a highly efficient polyphase implementation for arbitrary integer decimation ratios. The FB is tested through a 16-channel GDFT channelizer. The implementation is based on the Xilinx Zynq family of FPGAs and aims to show the data reuse and flexibility offered by the GDFT channelizer structure. General design criteria are summarized for the 16-channel polyphase FB channelizer. The performance in hardware resource usage is also presented, taking into account one of the main objectives of the current physics experiments, aiming to have an extremely large readout format.

Ca2+ effects on Fe(II) interactions with Mn-binding sites in Mn-depleted oxygen-evolving complexes of photosystem II and on Fe replacement of Mn in Mn-containing, Ca-depleted complexes.

Fe(II) cations bind with high efficiency and specificity at the high-affinity (HA), Mn-binding site (termed the "blocking effect" since Fe blocks further electron donation to the site) of the oxygen-evolving complex (OEC) in Mn-depleted, photosystem II (PSII) membrane fragments (Semin et al. in Biochemistry 41:5854, 2002). Furthermore, Fe(II) cations can substitute for 1 or 2Mn cations (pH dependent) in Ca-depleted PSII membranes (Semin et al. in Journal of Bioenergetics and Biomembranes 48:227, 2016; Semin et al. in Journal of Photochemistry and Photobiology B 178:192, 2018). In the current study, we examined the effect of Ca2+ cations on the interaction of Fe(II) ions with Mn-depleted [PSII(-Mn)] and Ca-depleted [PSII(-Ca)] photosystem II membranes. We found that Ca2+ cations (about 50mM) inhibit the light-dependent oxidation of Fe(II) (5µM) by about 25% in PSII(-Mn) membranes, whereas inhibition of the blocking process is greater at about 40%. Blocking of the HA site by Fe cations also decreases the rate of charge recombination between QA- and YZ•+ from t1/2 = 30 ms to 46ms. However, Ca2+ does not affect the rate during the blocking process. An Fe(II) cation (20µM) replaces 1Mn cation in the Mn4CaO5 catalytic cluster of PSII(-Ca) membranes at pH 5.7 but 2 Mn cations at pH 6.5. In the presence of Ca2+ (10mM) during the substitution process, Fe(II) is not able to extract Mn at pH 5.7 and extracts only 1Mn at pH 6.5 (instead of two without Ca2+). Measurements of fluorescence induction kinetics support these observations. Inhibition of Mn substitution with Fe(II) cations in the OEC only occurs with Ca2+ and Sr2+ cations, which are also able to restore oxygen evolution in PSII(-Ca) samples. Nonactive cations like La3+, Ni2+, Cd2+, and Mg2+ have no influence on the replacement of Mn with Fe. These results show that the location and/or ligand composition of one Mn cation in the Mn4CaO5 cluster is strongly affected by calcium depletion or rebinding and that bound calcium affects the redox potential of the extractable Mn4 cation in the OEC, making it resistant to reduction.

A scalable superconducting nanowire memory cell and preliminary array test

There has been a demand for a scalable superconducting memory technology for cryogenic computing for some time. This demand has proven difficult to satisfy due to the simultaneous need for high speed operation, low power consumption, and high density, all while maintaining cryogenic and SFQ compatibility. In an effort to satisfy this demand, we have developed a simple memory cell based on our prior work with nanowire-based memories. Due to the memory cell’s reliance on kinetic inductance, the cell can be scaled to almost any size. The cell has been designed specifically such that it can easily form into an array simply by arranging in a 2D pattern. This design eliminated the need for external addressing circuitry. This new cell, when operated in isolation and without the heater, performs very well with predicted bit error rates around 10−17. However, preliminary array tests show that while the memory operates, the predicted error rates rise to 1.5 × 10−3. We believe that this issue is predominantly due to the hTron-channel kinetic inductance dramatically changing upon the application of the row-select heaters. This issue might be addressed by designing the cell to compensate for the change in kinetic inductance when the heater is activated. If this remedy proves to be effective, then this memory would enable the development of compact and scalable memory arrays.

The Leafless Orchid Cymbidium macrorhizon Performs Photosynthesis in the Pericarp during the Fruiting Season.

Photosynthesis with highly photoreactive chlorophyll (Chl) provides energy for plant growth but with simultaneous risk of photooxidative damage and photoprotection costs. Although the leafless orchid Cymbidium macrorhizon mostly depends on mycorrhizal fungi for carbon, it accumulates Chl particularly during fruiting and may not be fully mycoheterotrophic. In fact, stable isotopic analysis suggested that the fruiting C. macrorhizon specimens obtain a significant proportion of its carbon demands through photosynthesis. However, actual photosynthetic characteristics of this leafless orchid are unknown. To reveal the functionality of photosynthetic electron transport in C. macrorhizon, we compared its photosynthetic properties with those of its relative mixotrophic orchid Cymbidium goeringii and the model plant Arabidopsis thaliana. Compared with C. goeringii and A. thaliana, maximum photochemical efficiency of PSII was substantially low in C. macrorhizon. Chl fluorescence induction kinetics revealed that the electron transport capacity of PSII was limited in C. macrorhizon. Chl fluorescence analysis at 77 K suggested partial energetic disconnection of the light-harvesting antenna from the PSII reaction center in C. macrorhizon. Despite its low PSII photochemical efficiency, C. macrorhizon showed photosynthetic electron transport activity both in the field and under laboratory conditions. Cymbidium macrorhizon developed strong nonphotochemical quenching in response to increased light intensity as did C. goeringii, suggesting the functionality of photoprotective systems in this orchid. Moreover, C. macrorhizon fruit developed stomata on the pericarp and showed net O2-evolving activity. Our data demonstrate that C. macrorhizon can perform photosynthetic electron transport in the pericarp, although its contribution to net carbon acquisition may be limited.

Norway spruce ecotypes distinguished by chlorophyll a fluorescence kinetics

Fast kinetics of chlorophyll a fluorescence in three Norway spruce ecotypes was investigated. Spruce ecotypes that come from different parts of the provenance regions were used to establish a common garden experiment in Central Bohemia (Czech Republic) in 1972. The hypothesis was based on the presumption that high-mountain spruce ecotype will benefit less from plain site compared to the mountain and lowland one after prolonged period of drought in 2018. FluorPen FP 110, spectrophotometer, and pressure chamber of Scholander type were used for fast kinetics of chlorophyll fluorescence induction, chlorophyll content, and water potential measurement. With exception of selected structural parameters, quantum yield of photosystem II (φP0) values did not signify any kind of stress so did the performance index (PIABS) The experiment confirmed high adaption potential for high-mountain spruce ecotype planted in low elevations.