Isotope Ratio Mass Spectrometry Research Articles

A study on the simultaneous determination of nitrogen content and 15N isotope abundance in plants using peak height intensities at m/z 28 and 29

A method for simultaneous determination of nitrogen content and 15N isotope abundance in plants was established by Elemental analysis-gas isotope ratio mass spectrometry. Taking poplar leaves and l-glutamic acid as standards, nitrogen content was determined using the standard curve established by weighted least squares regression between the mass of nitrogen element and the total peak height intensity at m/z 28 and 29. Then the 15N isotope abundance was calculated with the peak height intensity at m/z 28 and 29. Through the comparison of several sets of experiments, the impact of mass discrimination effect, tin capsule consumables, isotope memory effect, and the quality of nitrogen on the results were assessed. The results showed that with a weight of 1/x2, the standard curve has a coefficient of determination (R2) of 0.9996. Compared to the traditional Kjeldahl method, the measured nitrogen content deviated less than 0.2 %, and the standard deviation (SD) was less than 0.2 %. Compared to the sodium hypobromite method, the 15N isotopic abundances differed less than 0.2 atom%15N, and the SD was less than 0.2 atom% 15N. The established method offers the advantages of being fast, simple, accurate, and high throughput, providing a novel approach for the simultaneous determination of nitrogen content and 15N isotope abundance in plant samples.

Assessing Seasonal Effects on Identification of Cultivation Methods of Short-Growth Cycle Brassica chinensis L. Using IRMS and NIRS.

Seasonal (temporal) variations can influence the δ13C, δ2H, δ18O, and δ15N values and nutrient composition of organic (ORG), green (GRE), and conventional (CON) vegetables with a short growth cycle. Stable isotope ratio mass spectrometry (IRMS) and near-infrared spectroscopy (NIRS) combined with the partial least squares-discriminant analysis (PLS-DA) method were used to investigate seasonal effects on the identification of ORG, GRE, and CON Brassica chinensis L. samples (BCs). The results showed that δ15N values had significant differences among the three cultivation methods and that δ13C, δ2H, and δ18O values were significantly higher in winter and spring and lower in summer. The NIR spectra were relatively clustered across seasons. Neither IRMS-PLS-DA nor NIRS-PLS-DA could effectively identify all BC cultivation methods due to seasonal effects, while IRMS-NIRS-PLS-DA combined with Norris smoothing and derivative pretreatment had better predictive abilities, with an 89.80% accuracy for ORG and BCs, 88.89% for ORG and GRE BCs, and 75.00% for GRE and CON BCs. The IRMS-NIRS-PLS-DA provided an effective and robust method to identify BC cultivation methods, integrating multi-seasonal differences.

Procedures from samples to sulfur isotopic data: A review.

Sulfur isotopes have been widely used to solve some key scientific questions, especially in the last two decades with advanced instruments and analytical schemes. Different sulfur speciation and multiple isotopes analyzed in laboratories worldwide and in situ microanalysis have also been reported in many articles. However, methods of sampling to measurements are multifarious, and occasionally some inaccuracies are present in published papers. Vague methods may mislead newcomers to the field, puzzle readers, or lead to incorrect data-based correlations. We have reviewed multiple methods on sulfur isotopic analyses from the perspectives of sampling, laboratory work, and instrumental analysis in order to help reduce operational inhomogeneity and ensure the fidelity of sulfur isotopic data. We do not deem our proposed solutions as the ultimate standard methods but as a lead-in to the overall introduction and summary of the current methods used. It has been shown that external contamination and transformation of different sulfur species should be avoided during the sampling, pretreatment, storage, and chemical treatment processes. Conversion rates and sulfur isotopic fractionations during sulfur extraction, purification, and conversion processes must be verified by researchers using standard or known samples. The unification of absence of isotopic fractionation is needed during all steps, and long-term monitoring of standard samples is recommended. This review compiles more details on different methods in sampling, laboratory operation, and measurement of sulfur isotopes, which is beneficial for researchers' better practice in laboratories. Microanalyses and molecular studies are the frontier techniques that compare the bulk sample with the elemental analysis/continuous flow-gas source stable isotope ratio mass spectrometry method, but the latter is widely used. The development of sulfur isotopic measurements will lead to the innovation in scientific issues with sulfur proxies.

Molecular composition and characteristics of Sediment-adsorbed Dissolved Organic Matter (SDOM) along the coast of China

Sediment-adsorbed Dissolved Organic Matter (SDOM) in coast plays a crucial role in the terrestrial and marine carbon cycle processes of the global environment. However, understanding the transport dynamics of SDOM along the coast of China, particularly its interactions with sediments, remains elusive. In this study, we analyzed the δ13C and δ15N stable isotopic compositions, as well as the molecular characteristics of SDOM collected from coastal areas spanning the Bohai Sea (BS), Yellow Sea (YS), East China Sea (ECS), and South China Sea (SCS), by using isotope ratio mass spectrometry and Fourier Transform Ion Cyclotron Resonance Mass Spectrometry (FT-ICR-MS). We identified the predominant sources of carbon and nitrogen in coastal sediments, revealing terrigenous origins for most C and N, while anthropogenic sources dominated in the SCS. Spatial variations in SDOM chemodiversity were observed, with diverse molecular components influenced by distinct environmental factors and sediment sources. Notably, lignins and saturated compounds (such as proteins/amino sugars) were the predominant molecular compounds detected in coastal SDOM. Through Mantel tests and Spearman's correlation analysis, we elucidated the significant influence of spatial environmental factors (temperature, DO, salinity, and depth) and sediment sources on SDOM molecular chemodiversity. These findings contribute to a more comprehensive understanding of the carbon cycle dynamics along the Chinese coast.

Contact‐Electro‐Catalysis for Direct Oxidation of Methane under Ambient Conditions

AbstractThe conversion of methane under ambient conditions has attracted significant attention. Although advancements have been made using active oxygen species from photo‐ and electro‐ chemical processes, challenges such as complex catalyst design, costly oxidants, and unwanted byproducts remain. This study exploits the concept of contact‐electro‐catalysis, initiating chemical reactions through charge exchange at a solid–liquid interface, to report a novel process for directly converting methane under ambient conditions. Utilizing the electrification of commercially available Fluorinated Ethylene Propylene (FEP) with water under ultrasound, we demonstrate how this interaction promote the activation of methane and oxygen molecules. Our results show that the yield of HCHO and CH3OH can reach 467.5 and 151.2 μmol ⋅ gcat−1, respectively. We utilized electron paramagnetic resonance (EPR) to confirm the evolution of hydroxyl radicals (⋅OH) and superoxide radicals (⋅OOH). Isotope mass spectrometry (MS) was employed to analyze the elemental origin of CH3OH, which can be further oxidized to HCHO. Additionally, we conducted density functional theory (DFT) simulations to assess the reaction energies of FEP with H2O, O2, and CH4 under these conditions. The implications of this methodology, with its potential applicability to a wider array of gas‐phase catalytic reactions, underscore a significant advance in catalysis.

Contact-Electro-Catalysis for Direct Oxidation of Methane under Ambient Conditions.

The conversion of methane under ambient conditions has attracted significant attention. Although advancements have been made using active oxygen species from photo- and electro- chemical processes, challenges such as complex catalyst design, costly oxidants, and unwanted byproducts remain. This study exploits the concept of contact-electro-catalysis, initiating chemical reactions through charge exchange at a solid-liquid interface, to report a novel process for directly converting methane under ambient conditions. Utilizing the electrification of commercially available Fluorinated Ethylene Propylene (FEP) with water under ultrasound, we demonstrate how this interaction promote the activation of methane and oxygen molecules. Our results show that the yield of HCHO and CH3OH can reach 467.5 and 151.2 μmol ⋅ gcat -1, respectively. We utilized electron paramagnetic resonance (EPR) to confirm the evolution of hydroxyl radicals (⋅OH) and superoxide radicals (⋅OOH). Isotope mass spectrometry (MS) was employed to analyze the elemental origin of CH3OH, which can be further oxidized to HCHO. Additionally, we conducted density functional theory (DFT) simulations to assess the reaction energies of FEP with H2O, O2, and CH4 under these conditions. The implications of this methodology, with its potential applicability to a wider array of gas-phase catalytic reactions, underscore a significant advance in catalysis.

Resting cells of Skeletonema marinoi assimilate organic compounds and respire by dissimilatory nitrate reduction to ammonium in dark, anoxic conditions.

Diatoms can survive long periods in dark, anoxic sediments by forming resting spores or resting cells. These have been considered dormant until recently when resting cells of Skeletonema marinoi were shown to assimilate nitrate and ammonium from the ambient environment in dark, anoxic conditions. Here, we show that resting cells of S. marinoi can also perform dissimilatory nitrate reduction to ammonium (DNRA), in dark, anoxic conditions. Transmission electron microscope analyses showed that chloroplasts were compacted, and few large mitochondria had visible cristae within resting cells. Using secondary ion mass spectrometry and isotope ratio mass spectrometry combined with stable isotopic tracers, we measured assimilatory and dissimilatory processes carried out by resting cells of S. marinoi under dark, anoxic conditions. Nitrate was both respired by DNRA and assimilated into biomass by resting cells. Cells assimilated nitrogen from urea and carbon from acetate, both of which are sources of dissolved organic matter produced in sediments. Carbon and nitrogen assimilation rates corresponded to turnover rates of cellular carbon and nitrogen content ranging between 469 and 10,000 years. Hence, diatom resting cells can sustain their cells in dark, anoxic sediments by slowly assimilating and respiring substrates from the ambient environment.

Trace the origin of yak meat in Xizang based on stable isotope combined with multivariate statistics

In this study, the feasibility of tracing the origin of yak meat in Xizang Autonomous Region based on stable isotope combined with multivariable statistics was researched. The δ13C, δ15N, δ2H and δ18O in yak meat were determined by stable isotope ratio mass spectrometry, and the data were analyzed by analysis of variance, fisher discriminant analysis (FDA), back propagation (BP) neural network and orthogonal partial least squares discrimination analysis (OPLS-DA). The results showed that the δ13C, δ15N, δ2H and δ18O had significant differences among different origins (P < 0.05). The overall original correct discrimination rate of fisher discriminant analysis was 89.7 %, and the correct discrimination rate of cross validation was 88.2 %. The correct classification rate of BP neural network based on training set was 93.38 %, and the correct classification rate of BP neural network based on test set was 89.83 %. The OPLS-DA model interpretation rate parameter R2Y was 0.67, the model prediction rate parameter Q2 was 0.409, which could distinguish yak meat from seven different producing areas in Xizang Autonomous Region. The results showed that the origin of yak meat in Xizang Autonomous Region can be traced based on stable isotope combined with multivariate statistics.

Simultaneous detection of testosterone, nandrolone, and boldenone esters in dried blood spots for doping control in sports by liquid chromatography-tandem mass spectrometry.

Testosterone, nandrolone, and boldenone, which are listed as doping substances on the World Anti-Doping Agency Prohibited List, are mostly available commercially in esterified forms. Isotope ratio mass spectrometry (IRMS) represents a key tool for identifying these substances, as they are hydrolyzed and discharged in the urine as pseudo-endogenous substances. However, IRMS, which comprises a complicated process, cannot achieve the direct detection of steroid esters in blood samples. These substances can be detected using dried blood spots (DBSs), reducing the impact of esterase hydrolysis. Here, a simultaneous liquid chromatography-tandem mass spectrometry method for detecting 28 steroid (13 testosterone, nine nandrolone, and six boldenone) esters was developed using three DBS types of samples, including a cellulose paper and polymer. The substances were first derivatized with methyloxime to increase their sensitivities (the limits of detection were <0.1-0.4, <0.1-0.9, and <0.1-0.9ng/mL for the testosterone, nandrolone, and boldenone esters, respectively). Further, the DBS absorbents were verified since the effect of interferences depended on it. Next, a study involving seven participants was conducted to detect intramuscularly administered testosterone enanthate (100 mg). Polymer and cellulose papers were used to collect blood from their upper arms and fingertips, respectively, and testosterone enanthate was identified and detectable at both blood-collection sites for up to 144 and 216 h, respectively. Furthermore, testosterone enanthate was detectable in the DBS samples stored under refrigeration after 6 months, indicating the stable nature of DBS.

Geographical origin identification of Pujiang Kyoho grapes in China using stable isotope and elemental profiles

Grapes are an important seasonal fresh fruit in China, and their quality and nutrition is closely linked to their geographical origin. Stable isotopes and elemental profiles of grapes and corresponding soils from different regions and harvest years were determined using isotope ratio mass spectrometry (IRMS) and inductively coupled plasma mass spectrometry (ICP-MS). Results showed that stable isotope ratios and most elemental contents of grapes were significantly correlated to distinct regions and different harvest years. Na, Li, V, Co, Ni and Pb contents of grapes and corresponding soils were positively correlated, while Mg, Cu, Rb and Sr were negatively correlated (p < 0.05). A supervised chemometric model (random forest) was used to discriminate PGI Pujiang grapes from four other grape producing regions with 100% accuracy. These findings confirm that stable isotopes and multi-elements combined with chemometric analysis can effectively improve the accuracy of grape origin identification and minimize fraudulent mislabeling.

Research on the Application of Isotope Ratio Mass Spectrometry Technology in Traceability Detection of Stimulants

Research on the Application of Isotope Ratio Mass Spectrometry Technology in Traceability Detection of Stimulants

Isotope Ratio Mass Spectrometry for Geographical Origin Authentication and Adulteration Determination in Food Products

Isotope Ratio Mass Spectrometry for Geographical Origin Authentication and Adulteration Determination in Food Products

Oxygen Isotope and Fluorine Impurity Signatures during the Conversion of Uranium Ore Concentrates to Nuclear Fuel.

Within the front end of the nuclear fuel cycle, many processes impart forensic signatures. Oxygen-stable isotopes (δ18O values) of uranium-bearing materials have been theorized to provide the processing and geolocational signatures of interdicted materials. However, this signature has been minimally utilized due to a limited understanding of how oxygen isotopes are influenced during uranium processing. This study explores oxygen isotope exchange and fractionation between magnesium diuranate (MDU), ammonium diuranate (ADU), and uranyl fluoride (UO2F2) with steam (water vapor) during their reduction to UOx. The MDU was precipitated from two water sources, one enriched and one depleted in 18O. The UO2F2 was precipitated from a single water source and either directly reduced or converted to ADU prior to reduction. All MDU, ADU, and UO2F2 were reduced to UOx in a 10% hydrogen/90% nitrogen atmosphere that was dry or included steam. Powder X-ray diffraction (p-XRD) was used to verify the composition of materials after reduction as mixtures of primarily U3O8, U4O9, and UO2 with trace magnesium and fluorine phases in UOx from MDU and UO2F2, respectively. The bulk oxygen isotope composition of UOx from MDU was analyzed using fluorination to remove the lattice-bound oxygen, and then O2 was subsequently analyzed with isotope ratio mass spectrometry (IRMS). The oxygen isotope compositions of the ADU, UO2F2, and the resulting UOx were analyzed by large geometry secondary ion mass spectrometry (LG-SIMS). When reduced with steam, the MDU, ADU, and UO2F2 experienced significant oxygen isotope exchange, and the resulting δ18O values of UOx approached the values of the steam. When reduced without steam, the δ18O values of converted ADU, U3O8, and UOx products remained similar to those of the UO2F2 starting material. LG-SIMS isotope mapping of F impurity abundances and distributions showed that direct steam-assisted reduction from UO2F2 significantly removed F impurities while dry reduction from UO2F2 led to the formation of UOx that was enhanced in F impurities. In addition, when UO2F2 was processed via precipitation to ADU and calcination to U3O8, F impurities were largely removed, and reductions to UOx with and without steam each had low F impurities. Overall, these findings show promise for combining multiple signatures to predict the process history during the conversion of uranium ore concentrates to nuclear fuel.

Employing 11-Ketotestosterone as a Target Analyte for Adrenosterone (11OXO) Administration in Doping Controls.

Adrenosterone (Androst-4-ene-3,11,17-trione, 11OXO) is forbidden in sports according to the Prohibited List of the World Anti-Doping Agency. The administration of 11OXO may be detected by monitoring the urinary concentrations of its main human metabolites 11β-hydroxy-androsterone and 11β-hydroxy-etiocholanolone. Preliminary urinary concentration and concentration ratio thresholds have been established for sports drug testing purposes, but adaptations are desirable as the suggested limits would result in numerous suspicious findings due to naturally elevated concentrations and ratios. Recently, the metabolism of 11-oxo-testosterone (KT) was investigated in the context of anti-doping research, resulting in a preliminary urinary concentration threshold and a confirmation procedure based on the determination of carbon isotope ratios (CIRs). Gas chromatography coupled to isotope ratio mass spectrometry was employed to investigate the CIRs of selected steroids. As KT is also a metabolite of 11OXO, the developed protocols for KT have been tested to elucidate their potential to detect the administration of 11OXO after a single oral dose of 100 mg. In order to further improve the analytical approach, the threshold for urinary concentrations of KT was re-investigated by employing a reference population of n = 5232 routine doping control samples. Quantification of urinary steroids was conducted by employing gas chromatography coupled to triple quadrupole mass spectrometry. Derived from these, a subset of n = 106 samples showing elevated concentrations of KT was investigated regarding their CIRs. By means of this, potentially positive samples due to the illicit administration of 11OXO or KT could be excluded, and the calculation of reference population-derived thresholds for the concentrations and CIR of KT was possible. Based on the results, the urinary concentration threshold for KT is suggested to be established at 130 ng/mL.

Comparative Analysis of Water Isotopic Compositions: Evaluating Isotope Analyzer for Soil and Extraction Method for Stem Water

Stable isotopes of water (δ2H and δ18O) are reliable tracers for the investigation of plant–soil–water interactions in forest ecosystems. However, variations in isotopic compositions may arise due to differences in analytical instruments and water extraction methods. In this study, we conducted three different experiments to identify isotopic differences caused by analytical and methodological variations. First, we analyzed soil water by using the two most commonly applied methods: isotope ratio mass spectrometry (IRMS) and cavity ring-down spectroscopy (CRDS). Second, we compared the isotopes in xylem water extracted from the stems of nine tree species using cryogenic vacuum distillation (CVD) with different heating times. Third, we compared the compositions in xylem water extracted with three different methods: mechanical squeezing using a pressure chamber (PC), an induction module (IM), and CVD. The differences in isotopic composition between IRMS and CRDS were significant but minimal. Soil properties were not significant factors contributing to differences between the two instruments. For the xylem water extraction with CVD, each of the nine tree species required heating for more than three hours. Significant differences were observed in δ2H among the three extraction methods for xylem water. Xylem water extracted by CVD showed more depleted values compared to those obtained by PC and IM. Our results highlight the importance of considering analytical and methodological variations in stable isotope analysis.

Relative quantitation of chiral thiol compounds labeled based on isotope novel mass spectrometry probes: Monitoring of the dynamic changes of chiral thiol compounds in human urine during normal, exercise, and rest recovery states

Monitoring changes in the content of chiral thiol compounds in the human body is crucial for the early diagnosis of oxidative stress-related diseases and the exploration of their pathogenesis. To address this, we synthesized a novel isotope mass spectrometry (MS) probe, denoted as (R)-(5-(3-isothiocyanato (13C) pyrrolidin-1-yl)-5-oxopentyl) triphenylphosphonium (N13CS-OTPP), with triphenylphosphine as its parent structure. In this study, we established a new ultra-high-performance liquid chromatography high-resolution mass spectrometry (UHPLCHRMS) relative quantitative method to monitor chiral thiol compounds in human urine under varying oxidative stress conditions. This method relies on the ratio of 12C/13C isotope-labeled peak areas. To assess the chiral separation efficiency of N13CS-OTPP, we employed three types of thiol compounds (D/L-GSH, D/L-Cys, and D/L-Hcy) and observed separation degrees (Rs) ranging from 1.82 to 1.89. We further validated the accuracy and feasibility of our relative quantitative methods using D/L-Cys-as a model compound. N12C/13CS-OTPP-Cys-exhibited excellent linearity (R2 = 0.9993–0.9994) across different molar ratios (D/L-Cys = 10:1, 4:1, 2:1, 1:1, 1:2, 1:4, 1:10) and achieved a low limit of detection (LOD) of 2.5 fmol. Additionally, we monitored the dynamic changes in urine D/L-Cys-and D/L-Hcy ratios in 12 healthy volunteers (six males and six females) under various oxidative stress states. We generated fitting curves and investigated the trends in chiral thiol compounds in vivo. This study introduces a novel method for the relative quantitative monitoring of chiral thiol compounds in different oxidative stress states within the human body. It also presents a new strategy for understanding the pathogenesis of related diseases resulting from the abnormal metabolism of thiol compounds.

Forensic investigation of falsified antimalarials using isotope ratio mass spectrometry: a pilot investigation

We explored whether isotope ratio mass spectrometry (IRMS) is useful to investigate the origin of falsified antimalarials. Forty-four falsified and genuine antimalarial samples (artesunate, artemether-lumefantrine, dihydroartemisinin-piperaquine and sulphamethopyrazine-pyrimethamine) were analyzed in bulk for carbon (C), nitrogen (N), and oxygen (O) element concentrations and stable isotope ratios. The insoluble fraction (“starch”) was extracted from 26 samples and analyzed. Samples of known geographical origin maize, a common source of excipient starch, were used to produce a comparison dataset to predict starch source. In both an initial (n = 18) and a follow-on set of samples that contained/claimed to contain artesunate/artemether (n = 26), falsified antimalarials had a range of C concentrations less than genuine comparator antimalarials and δ13C values higher than genuine comparators. The δ13C values of falsified antimalarials suggested that C4 plant-based organic material (e.g., starch derived from maize) had been included. Using the known-origin maize samples, predictions for growth water δ18O values for the extracted “starch” ranged from − 6.10 to − 1.62‰. These findings suggest that IRMS may be a useful tool for profiling falsified antimalarials. We found that C4 ingredients were exclusively used in falsified antimalarials versus genuine antimalarials, and that it may be possible to predict potential growth water δ18O values for the starch present in falsified antimalarials.

Development of a Matrix‐Matched Barite Reference Material (NWU‐Brt) for Calibration of In Situ S Isotope Measurements by Laser Ablation Multi‐Collector Inductively Coupled Plasma‐Mass Spectrometry

A new matrix‐matched reference material (NWU‐Brt) with sulfur isotope ratios resembling those of natural barites has been developed for in situ S isotope measurements by laser ablation multi‐collector inductively coupled plasma‐mass spectrometry (LA‐MC‐ICP‐MS). A 100 g quantity of natural barite crystal was milled to ultra‐fine particles and sintered to a solid block using a fast hot‐pressing sintering technique (FHPS). We report δ34S ratios determined by isotope ratio mass spectrometry (IRMS), solution nebuliser multi‐collector inductively coupled plasma‐mass spectrometry (SN‐MC‐ICP‐MS) and LA‐MC‐ICP‐MS, involving up to six participating laboratories. The homogeneity of δ34S ratios of the synthesised barite was tested by LA‐MC‐ICP‐MS with an analytical spot size of 53 μm. The LA‐MC‐ICP‐MS results show that NWU‐Brt demonstrates a satisfactory homogeneous composition and is an appropriate material for calibrating δ34S ratios in barite. IRMS and SN‐MC‐ICP‐MS produced mean δ34S values of +14.17 ± 0.42‰ (2s) and +14.27 ± 0.23‰ (2s), respectively. The results of LA‐MC‐ICP‐MS analyses are consistent with the IRMS and SN‐MC‐ICP‐MS ratios within uncertainty. Overall, our results confirm the suitability of NWU‐Brt for the calibration of δ34S ratios in barite using LA‐MC‐ICP‐MS.

Affordable event and monthly rain samplers: Improving isotopic datasets to understand meteorological processes.

Water-stable isotopes in rainfall are powerful tracers of atmospheric processes at different spatial and temporal scales. However, commercially available rain samplers for isotopic analysis are prohibitively expensive, especially for high spatial resolution networks and studies conducted in developing countries. A low-cost, simple, and robust sampler was designed for event and monthly rainfall samplings. Rainfall collectors were built based on existing designs provided in the literature and using easily accessible materials. Event samplers were filled with different volumes of reference water and left for 72 h in laboratory conditions to determine the minimum amount of rainfall to be collected to minimize isotopic fractionation, from both postsampling evaporation and equilibration. Samples were analyzed using dual-inlet isotope ratio mass spectrometry and cavity ring-down spectroscopy. For samples larger than 4% of the bottle's capacity, the evaporative enrichment due to Rayleigh distillation is negligible compared to the overall analytical uncertainty. Using a tube connecting the funnel to the water sample has proved to reduce postsampling evaporation by at least five times. To limit water self-diffusion, we recommend collecting the largest rainfall amount possible. Under these conditions, these collectors are suitable for rainfall sampling for isotopic analysis. This low-cost methodology will enable isotopic sampling of precipitation at high spatial resolutions and democratize the use of isotopes for hydrological studies in developing countries. All instructions for building and using these samplers are made openly accessible to the scientific community so they can be repeated and adapted to the needs of each project.

Prevalence of nandrolone preparations with endogenous carbon isotope ratios in Australia

AbstractNandrolone and its prohormones, including 19‐norandrost‐4‐ene‐3,17‐dione and 19‐norandrost‐4‐ene‐3β,17β‐diol, are anabolic steroids forbidden at all times in sports according to the World Anti‐Doping Code Prohibited List and its metabolite 19‐norandrosterone (19NA) is the preferred urinary target compound to identify their abuse. In recent years, an increasing number of 19NA isotope ratio mass spectrometry (IRMS) cases have arisen that, based on the initial testing procedure, were likely to result in an adverse analytical finding but were concluded negative after IRMS analysis. The current study was therefore set up to gain a better insight on the prevalence of nandrolone preparations with endogenous carbon isotope ratio values in Australia. Suitable workplace (non‐athlete) urine samples that had previously been reported positive for 19NA were identified and analysed on IRMS. A total of 82% of the samples that were analysed were reported with enriched carbon isotope ratios of 19NA (i.e., 19NA greater than −26‰). This indicates that there is a high prevalence of nandrolone‐containing anabolic androgenic steroid preparations in Australia that have ‘endogenous’ carbon isotope ratios which reduces the ability to identify exogenous nandrolone.