Biomechanical Investigation Research Articles

A novel spine tester TO GO.

Often after large animal experiments in spinal research, the question arises-histology or biomechanics? While biomechanics are essential for informed decisions on the functionality of the therapy being studied, scientists often choose histological analysis alone. For biomechanical testing, for example, flexibility, specimens must be shipped to institutions with special testing equipment, as spine testers are complex and immobile. The specimens must usually be shipped frozen, and, thus, biological and histological investigations are not possible anymore. To allow both biomechanical and biological investigations with the same specimen and, thus, to reduce the number of required animals, the aim of the study was to develop a spine tester that can be shipped worldwide to test on-site. The "Spine Tester TO GO" was designed consisting of a frame with three motors that initiate pure moments and rotate the specimen in three motion planes. A load cell and an optical motion tracking system controlled the applied loads and measured range of motion (ROM) and neutral zone (NZ). As a proof of concept, the new machine was validated and compared under real experimental conditions with an existing testing machine already validated employing fresh bovine tail discs CY34 (n = 10). The new spine tester measured reasonable ROM and NZ from hysteresis curves, and the ROM of the two testing machines formed a high coefficient of determination R 2 = 0.986. However, higher ROM results of the new testing machine might be explained by the lower friction of the air bearings, which allowed more translational motion. The spine tester TO GO now opens up new opportunities for on-site flexibility tests and contributes hereby to the 3R principle by limiting the number of experimental animals needed to obtain full characterization of spine units at the macroscopic, biomechanical, biochemical, and histological level.

A biomechanical investigation comparing a novel bone cement bridging screw system with conventional treatment methods for Kummell’s disease

Based on the characteristics of Kummell’s disease (KD) and related anatomical structures of the thoracolumbar spine, a novel bone cement screw system has been designed to effectively avoid the cement loosening and displacement. This experiment aimed to assess the biological effects of the novel bone cement screw system in KD on fresh cadaveric thoracolumbar spine specimens, thereby discussing its potential application value and providing a foundation for clinical implementation. This study employed a total of 50 fresh female adult cadaver specimens. Each specimen underwent extraction of the T12 to L2 segment followed by the creation of an artificial KD model at the L1 segment and subsequent establishment of five distinct types of bone cement repair models. Model A represents the percutaneous vertebroplasty (PVP) model, Model B combines PVP with unilateral percutaneous pediculoplasty (PPP), Model C combines PVP with bilateral PPP, Model D introduces the novel bone cement screw combined with unilateral PVP, and Model E combines the novel screw with bilateral PVP, each group consists of 10 specimens. Subsequently, the six-axis spine robot was employed to execute cement three-dimensional biomechanical strength tests in six directions, including anterior flexion and posterior extension, left and right lateral bending, as well as left and right rotation. The novel bone cement screw, whether used unilaterally or bilaterally in combination with the PVP model, exhibits significantly reduced bone cement mobility and superior biomechanical stability during anterior flexion, posterior extension, left lateral bending, and right lateral bending (P<0.05).No significant differences were observed among the five models under both left and right rotation (P > 0.05).When comparing the novel bone cement screw combined with PVP unilaterally and bilaterally, no statistically significant difference was observed in the stability of bone cement across all six directions of motion (P>0.05). To conclude, this novel bone cement bridging screw system exhibits superior biomechanical stability compared to commonly used treatments. Furthermore, both unilateral and bilateral implementations of the novel bone cement screw system yield without significant differences observed. These findings present a reliable and innovative approach for clinical management of KD.

Biomechanical investigation of positive reduction in the femoral neck fracture: a finite element analysis.

Gotfried positive reduction offers an alternative strategy for femoral neck fracture (FNF) when achieving anatomical reduction is challenging. However, the biomechanical consequences of positive reduction remain unclear. The purpose of this study was to investigate the biomechanical behavior of positive reduction across different Pauwels classification, providing a reference for quantifying positive reduction in clinical practice. Three-dimensional (3D) models of FNF were established and categorized according to the Pauwels classifications (Pauwels I, II, and III), each of them contained seven models with different reduction qualities, including an anatomical reduction model, two negative reduction models, and four positive reduction models, all of which were stabilized with dynamic hip screws (DHS) and cannulated screws (CS). We investigated the maximal von-Mises stress of internal fixation and proximal femoral, femoral fragment displacement, and maximal von-Mises strain at the proximal fragment fracture site when a 2100N load was applied to the femoral head. The maximum von-Mises stress on the internal fixators in each Pauwels group was lowest in the anatomical reduction model. In the Pauwels I group, positive reduction exceeding 3mm resulted in the maximum von-Mises stress on the internal fixators surpassing that of the negative reduction model. For the Pauwels II group, positive reduction beyond 2mm led to the maximum von-Mises stress on the internal fixators exceeding that of the negative reduction model. In the Pauwels III group, positive reduction beyond 1mm caused the maximum von-Mises stress on the internal fixators to be higher than that of the negative reduction model. The maximum von-Mises strain at the fracture site of proximal femur fragment increased with positive reduction. Varus displacement increased in positive reduction models as the Pauwels angle rose, potentially exacerbating rotation deformity in Pauwels III group. Excessive positive reduction may increase the risk of FNF failure after internal fixation. From a biomechanical stability perspective, positive reduction should be limited to 3mm or below in the Pauwels I group, restricted to not exceed 2mm in the Pauwels II group, and should not exceed 1mm in the Pauwels III group. Negative reduction should be avoided in all Pauwels groups.

A Flat Reconstruction of the Medial Collateral Ligament and Anteromedial Structures Restores Native Knee Kinematics: A Biomechanical Robotic Investigation

Background: Injuries of the superficial medial collateral ligament (sMCL) and anteromedial structures of the knee result in excess valgus rotation and external tibial rotation (ER) as well as tibial translation. Purpose: To evaluate a flat reconstruction of the sMCL and anteromedial structures in restoring knee kinematics in the combined MCL- and anteromedial-deficient knee. Study Design: Controlled laboratory study. Methods: Eight cadaveric knee specimens were tested in a 6 degrees of freedom robotic test setup. Force-controlled clinical laxity tests were performed with 200 N of axial compression in 0°, 30°, 60°, and 90° of flexion: 8 N·m valgus torque, 5 N·m ER torque, 89 N anterior tibial translation (ATT) force, and an anteromedial drawer test consisting of 89 N ATT force under 5 N·m ER torque. After determining the native knee kinematics, we transected the sMCL, followed by the deep medial collateral ligament (dMCL). Subsequently, a flat reconstruction of the sMCL with anteromedial limb, mimicking the function of the anteromedial corner, was performed. Mixed linear models were used for statistical analysis (P < .05). Results: Cutting of the sMCL led to statistically significant increases in laxity regarding valgus rotation, ER, and anteromedial translation in all tested flexion angles (P < .05). ATT was significantly increased in all flexion angles but not at 60° after cutting of the sMCL. A combined instability of the sMCL and dMCL led to further increased knee laxity in all tested kinematics and flexion angles (P < .05). After reconstruction, the knee kinematics were not significantly different from those of the native state. Conclusion: Insufficiency of the sMCL and dMCL led to excess valgus rotation, ER, ATT, and anteromedial tibial translation. A combined flat reconstruction of the sMCL and the anteromedial aspect restored this excess laxity to values not significantly different from those of the native knee. Clinical Relevance: The presented reconstruction might lead to favorable results for patients with MCL and anteromedial injuries with an anteromedial rotatory knee instability.

Specific fibre areas in the femoral footprint of the posterior cruciate ligament act as a major contributor in resisting posterior tibial displacement: A biomechanical robotic investigation.

Similar to the anterior cruciate ligament, the femoral footprint of the posterior cruciate ligament (PCL) is composed of different fibre areas, possibly having distinct biomechanical functions. The aim of this study was to determine the role of different fibre areas of the femoral footprint of the PCL in restraining posterior tibial translation (PTT). A sequential cutting study was performed on eight fresh-frozen human knee specimens, utilizing a six-degrees-of-freedom robotic test setup. The femoral attachment of the PCL was divided into 15 areas, which were sequentially cut from the bone in a randomized sequence. After determining the native knee kinematics, a displacement-controlled protocol was performed replaying the native motion, while constantly measuring the force. The reduction of the restraining force presented the percentage contribution of each cut, according to the principle of superposition. The PCL was found to contribute 29 ± 16% in 0°, 51 ± 24% in 30°, 60 ± 22% in 60° and 55 ± 18% in 90°, to restricting a PTT. The fibre areas contributing the most were located at the proximal border of the PCL footprint, away from the cartilage, and directly adjacent to the medial intercondylar ridge (p < 0.05). Of these, one fibre area showed the highest contribution at all flexion angles. This area was located at the posterior half of the medial intercondylar ridge. No clear assignment of the areas to either the anterolateral or posteromedial bundle was possible. An area towards the proximal and posterior part of the femoral PCL footprint was found to significantly restrain a posterior tibial force. Based on the data of this testing setup, a PCL graft positioned at the identified area may best mimic the part of the native PCL, which bears the most load in resisting a PTT force. No evidence level (laboratory study).

Management of ZMC Fractures - A Review Article

Fractures of the zygomaticomaxillary complex (ZMC) are frequent face injuries treated with two- or three-point fixation procedures. This review examines the benefits and drawbacks of each strategy. For less complicated fractures, two-point fixation is less invasive and also requires less time during surgery, but it may not provide adequate stability. More structural support is provided with three-point fixation, especially in cases of comminuted or displaced fractures, although the procedure takes longer and may raise the risk of infection. In order to determine the best fixing option based on fracture severity and patient-specific characteristics, this article contrasts clinical and biomechanical investigations. A tailored approach is recommended for the best outcomes.

The deltotrapezial fascia stabilizes the AC-Joint and its reconstruction restores the horizontal stability in AC-joint separations—a biomechanical comparison

BackgroundVarious techniques are available for the reconstruction of acromioclavicular joint (ACJ) dislocations, with the main focus being on restoration of the AC capsule or coracoclavicular (CC) ligaments. Recent research has underlined the significance of the deltotrapezial fascia (DTF) and related muscles as dynamic stabilizers of the ACJ. HypothesisReconstruction of the DTF increases the stability of the ACJ in the horizontal plane more than a complete transection of the fascia, while not restoring the stability of the native state. MethodsFive pairs of human cadaveric shoulders including the torsos were included in the study and underwent cyclic anterior-posterior loading using an electromechanical testing machine. The shoulders were put into three groups: group N (n = 10): native ACJ; group T (n = 10): ACJ with transected DTF; group R (n = 10): ACJ with reconstruction of the DTF after transection. The dislocation was recorded with an 3D optical measuring system. ResultsGroup N showed a mean horizontal displacement of 2.94 mm (± 1.26), group T showed a mean anterior displacement of 3.33 mm (± 1.37) and group R showed a mean anterior displacement of 2.95 mm (± 1.08). The mean anterior displacement for group T was significantly higher after every measured number of cycles compared with groups N and R. There was no significant difference in mean anterior displacement between groups N and R. ConclusionThe transection of the DTF results in significantly reduced stability in the horizontal plane of the ACJ. A reconstruction of the DTF restores the stability of the native ACJ in the horizontal plane. Further clinical and biomechanical investigations should focus on reconstruction techniques of the DTF.

Crossing the Cervicothoracic Junction: A Biomechanical Investigation of C7 vs T1 Caudal Selection's Effect on Adjacent Segment Motion in Posterior Cervical Fusion.

Biomechanical Study. This study aims to evaluate the biomechanical adjacent segment effects of multi-level posterior cervical fusion constructs that terminate at C7 compared to those that terminate at T1 in cadaveric specimens. The cervicothoracic junction poses unique challenges for spine surgeons. Deciding to terminate multi-level posterior cervical fusion constructs at C7 or extend them across the cervicothoracic junction remains a controversial issue. Six cadaveric specimens underwent biomechanical testing in the intact state and after instrumentation with constructs from C3 and terminating at either C7 or T1. Range of motion (ROM) was assessed in flexion-extension, lateral bending, and axial rotation globally and at cranial and caudal adjacent segments. There was a significant decrease in overall flexion/extension by both C7 (-35.5°, P=0.002) and T1 (-39.8°, P=0.002) instrumentation compared to the intact spine. T1 instrumentation had significantly lower (-4.3°, P=0.008) flexion/extension ROM compared to C7 instrumentation. There were significant decreases in axial rotation by both C7 (-31.4°, P=0.009) and T1 (-36.8°, P=0.009) instrumentation compared to the intact spine, but no significant differences were observed between the two. There were also significant decreases in lateral bending by both C7 (-27.9°, P=0.022) and T1 (-33.7°, P=0.022) instrumentation compared to the intact spine, but no significant differences were observed between the two. No significant differences were observed in ROM at cranial or caudal adjacent segments between constructs terminating at C7 and those extending to T1. This biomechanical investigation demonstrates that constructs that cross the cervicothoracic junction experience less overall spinal motion in flexion-extension compared to those that terminate at C7. However, contrary to prior studies there is no difference in cranial and caudal adjacent segment motion. Surgeons should make clinical decisions regarding the caudal extent of fusion in multi-level posterior cervical fusions without major concerns about adjacent segment motion.

Primary Stability of Kyphoplasty in Incomplete Vertebral Body Burst Fractures in Osteoporosis: A Biomechanical Investigation.

Background: The objective of our study was to biomechanically evaluate the use of kyphoplasty to stabilize post-traumatic segmental instability in incomplete burst fractures of the vertebrae. Methods: The study was performed on 14 osteoporotic spine postmortem samples (Th11-L3). First, acquisition of the native multisegmental kinematics in our robot-based spine tester with three-dimensional motion analysis was set as a baseline for each sample. Then, an incomplete burst fracture was generated in the vertebral body L1 with renewed kinematic testing. After subsequent kyphoplasty was performed on the fractured vertebral body, primary stability was examined again. Results: Initially, a significant increase in the range of motion after incomplete burst fracture generation in all three directions of motion (extension-flexion, lateral tilt, axial rotation) was detected as proof of post-traumatic instability. There were no significant changes to the native state in the adjacent segments. Radiologically, a significant loss of height in the fractured vertebral body was also shown. Traumatic instability was significantly reduced by kyphoplasty. However, native kinematics were not restored. Conclusions: Although post-traumatic segmental instability was significantly reduced by kyphoplasty in our in vitro model, native kinematics could not be reconstructed, and significant instability remained.

Investigation of Foot Biomechanics in 5-15 Years Old Children Performing Gymnastics

Investigation of Foot Biomechanics in 5-15 Years Old Children Performing Gymnastics

Understanding the influence of context on real-world walking energetics.

Speeds that minimize energetic cost during steady-state walking have been observed during lab-based investigations of walking biomechanics and energetics. However, in real-world scenarios, humans walk in a variety of contexts that can elicit different walking strategies, and may not always prioritize minimizing energetic cost. To investigate whether individuals tend to select energetically optimal speeds in real-world situations and how contextual factors influence gait, we conducted a study combining data from lab and real-world experiments. Walking kinematics and context were measured during daily life over a week (N=17) using wearable sensors and a mobile phone. To determine context, we utilized self-reported activity logs, GPS data and follow-up exit interviews. Additionally, we estimated energetic cost using respirometry over a range of gait speeds in the lab. Gross and net cost of transport were calculated for each participant, and were used to identify energetically optimal walking speed ranges for each participant. The proportion of real-world steady-state stride speeds within these ranges (gross and net) were identified for all data and for each context. We found that energetically optimal speeds predicted by gross cost of transport were more predictive of walking speeds used during daily life than speeds that would minimize net cost of transport. On average, 82.2% of all steady-state stride speeds were energetically optimal for gross cost of transport for all contexts and participants, while only 45.6% were energetically optimal for net cost of transport. These results suggest that while energetic cost is a factor considered by humans when selecting gait speed in daily life, it is not the sole determining factor. Context contributes to the observed variability in movement parameters both within and between individuals.

Kinematics and Activation of Hamstring Muscles During the Initial Acceleration Phase of Sprinting in Soccer Players: A Biomechanical Investigation

Kinematics and Activation of Hamstring Muscles During the Initial Acceleration Phase of Sprinting in Soccer Players: A Biomechanical Investigation

Immediate Effects of Wearing an Ankle Bandage on Fine Coordination, Proprioception, Balance and Gait in the Subacute Phase of Ankle Sprains.

Ankle sprains are the most frequently occurring musculoskeletal injuries among recreational athletes. Ankle support through bandages following the initial orthotic treatment might be beneficial for rehabilitation purposes. However, the literature is sparse regarding the use of an ankle support directly after the acute phase of an ankle sprain. Therefore, this study investigates the hypothesis that wearing an ankle bandage immediately after an acute ankle sprain improves motor performance, stability and reduces pain. In total, 70 subjects with acute unilateral supination trauma were tested. Subjects were tested five weeks post-injury to assess immediate effects of the ankle bandage. On the testing day, subjects completed rating questionnaires and underwent comprehensive biomechanical assessments. Biomechanical investigations included fine coordination and proprioception tests, single leg stances, the Y-Balance test, and gait analysis. All biomechanical investigations were conducted for the subject's injured leg with and without a bandage (MalleoTrain® Bauerfeind AG, Zeulenroda-Triebes, Germany) and the healthy leg. Results indicated moderate to strong improvements in ankle stability and pain relief while wearing the bandage. Wearing the bandage significantly normalized single leg stance performance (p < 0.001), stance phase duration (p < 0.001), and vertical ground reaction forces during walking (p < 0.05). However, the bandage did not have a clear effect on fine coordination and proprioception. The findings of our study suggest that ankle bandages may play a crucial role in early-stage rehabilitation by enhancing motor performance and reducing pain.

Effects of A2 Pulley Venting on Bowstringing and Tendon Slack: A Biomechanical Investigation.

A2 pulley release is often needed for exposure of the lacerated tendon, retrieval of retracted tendons, placement of core sutures, or to permit full motion and gliding of the repaired and edematous tendon. However, there is no agreement in the literature on the specific quantity of pulley venting that can be performed and recommendations are limited to an undefined "judicious release" of the pulleys when necessary. Following a previously developed testing protocols, finger kinematics, tendon excursion, and bowstringing were evaluated on cadaveric hands for venting in increments of 20% of the pulley length. In our study, we found a statistically significant influence of venting on bowstringing, although no difference was found between fingers, and a significant difference in tendon slack, which was variable depending on the finger. Bowstringing started increasing at 20% of A2 venting and peaked at full release. Tendon slack did not start until 40% of A2 venting on the index finger, but started at 20% on the middle, ring, and small fingers. Venting of the A2 pulley leads to an incremental increase in tendon bowstringing and tendon slack. However, differences in metacarpophalangeal flexion angle were not observed until full A2 pulley release, and only observed in the index finger, and no differences were observed in proximal interphalangeal flexion angles. Therefore, the benefit of releasing the A2 pulley when clinically necessary will likely outweigh the risks of loss of motion or strength.

Biomechanical Investigation of Lower Limbs during Slope Transformation Running with Different Longitudinal Bending Stiffness Shoes.

During city running or marathon races, shifts in level ground and up-and-down slopes are regularly encountered, resulting in changes in lower limb biomechanics. The longitudinal bending stiffness of the running shoe affects the running performance. This research aimed to investigate the biomechanical changes in the lower limbs when transitioning from level ground to an uphill slope under different longitudinal bending stiffness (LBS) levels in running shoes. Fifteen male amateur runners were recruited and tested while wearing three different LBS running shoes. The participants were asked to pass the force platform with their right foot at a speed of 3.3 m/s ± 0.2. Kinematics data and GRFs were collected synchronously. Each participant completed and recorded ten successful experiments per pair of shoes. The range of motion in the sagittal of the knee joint was reduced with the increase in the longitudinal bending stiffness. Positive work was increased in the sagittal plane of the ankle joint and reduced in the keen joint. The negative work of the knee joint increased in the sagittal plane. The positive work of the metatarsophalangeal joint in the sagittal plane increased. Transitioning from running on a level surface to running uphill, while wearing running shoes with high LBS, could lead to improved efficiency in lower limb function. However, the higher LBS of running shoes increases the energy absorption of the knee joint, potentially increasing the risk of knee injuries. Thus, amateurs should choose running shoes with optimal stiffness when running.

Ex vivo biomechanical investigations of combined extra- and intracapsular stabilization in canines with cranial cruciate ligament deficiency.

Intracapsular reconstruction (ICR) has long been recommended as a treatment for cranial cruciate ligament deficiency (CCLD) in dogs, but it has fallen out of favor due to its inferior long-term functional outcomes. These outcomes may be attributed to the poor stiffness and strength of the graft in the early period before ligamentization is completed. Additional placement of extracapsular sutures to mechanically protect the graft during the ligamentization process may be a viable method to address this problem. However, the biomechanical effect of this combined surgical approach remains unknown. This study aimed to evaluate the 3D kinematics of the CCLD stifle in dogs in response to ICR and combined extra- and intracapsular reconstruction (CEICR). Twelve hindlimbs were collected from nine cadavers of mature dogs. The limbs were tested using a custom-made testing apparatus that reproduces their sagittal plane kinematics during the stance phase. Four statuses of stifle joints were tested, namely, (a) cranial cruciate ligament (CCL) intact; (b) CCLD; (c) CCLD stifle stabilized by CEICR; and (d) CCLD stifle stabilized by ICR only. Three-dimensional stifle kinematics at the 5 instances of the stance phase were measured with an optoelectronic system. The results showed that ICR marginally corrects the increased adduction, internal rotation, and caudodistal stifle joint center displacement that occur as a result of CCLD. CEICR led to better restoration of the stifle kinematics, especially with respect to the internal rotation and cranial translation stabilities. Furthermore, CEICR only resulted in minor excessive restraints on other motion components. The findings indicated that the additional lateral fabellotibial suture offers immediate stability to the stifle, consequently lowering the risk of graft over-elongation in the short term postoperatively. Considering the propensity for the extracapsular suture to degrade over time, further in vivo studies are warranted to explore the long-term effects of the CEICR procedure.

A biomechanical investigation of miniscrews placed on a mandible for temporary anchorage; a patient-specific finite element analysis

Miniscrews are temporary skeletal anchorage devices that are widely used in orthodontic treatment, and their success depends on the placement area, angle, technique, and screw dimensions. This study aimed to investigate the effects of miniscrew lengths, insertion angles, and force directions on a mandible model consisting of teeth, cortical and cancellous bones. One Dental Volumetric Tomography (DVT) scan from a patient who had miniscrews were used for mandibular bone modeling to perform finite element analysis. The model variables included miniscrew lengths (6, 8, and 10 mm), insertion angles (−15°, 45°, 60°, and 90°), and force directions (30°, 45°, and 60°). The minimum and maximum stresses were calculated as 18.61 and 37.11 MPa at 6 mm and 10 mm, respectively. According to the insertion angles, the lowest stress was observed at 60°, while the highest stress was found at 15° in the ventral direction. At force directions, the lowest stress was at 60°, and the highest stress was at 45°. However, there were no significant differences in insertion angles and force directions. A statistically significant difference was determined in miniscrew length. As a result, the best result was calculated to be 6 mm inserted at a 60° angle, which could induce the lowest stress. Increasing the miniscrew length will increase the stress on the mandible. In addition, because of the higher force direction, stress decreases with shorter power arms.

The effect of L-Arginine therapy on achilles tendon healing: A histological and biomechanical investigation in an animal model

PurposeSeveral clinical and experimental studies have revealed that L-Arginine, which has antioxidant properties, accelerates tissue healing. This study examined the in vivo effects of oral L - Arginine supplementation on tendon regeneration in Wistar rats. MethodFor each weighting of an average of 250–300 g, 24 Wistar rats were separated into three equal groups. Each rat's right hind leg Achilles tendons were tenotomized and then repaired. The first group (Control) was followed up with a regimen of standard food and water. In the second group (L-Arg Low Dose), 300 mg/kg, and in the third group (L-Arg High Dose), 600 mg/kg L-Arginine was administered in water daily with a regimen of standard food and water ad libitum. After eight weeks, the rats were sacrificed, and the tendons were histologically and biomechanically analyzed. ResultsTendon peak strength values of the L-Arg Low Dose and L-Arg High Dose groups were similar but significantly higher than the control group. A statistically significant difference was observed between the groups in terms of ground substance, fiber arrangement, cellularity, hyalinization, and GAG properties ( p = 0.05, p = 0.002, p = 0.016, p = 0.027, p = 0.05). There was no statistically significant difference between the groups according to the histological examination of collagen properties, fiber structure, tenocyte properties, rounding of the nuclei, and collagen stainability. (p = 0.999, p = 0.061, p = 0.195, p = 0.195, p = 0.130). No mortality, wound complications, or re-ruptures were observed. ConclusionCompared with the control group, histologically and biomechanically distinct therapeutic effects of L-Arginine supplementation on tendon healing were determined. Level of clinical evidence5

Locked plate constructs are not necessarily stiffer than nonlocked constructs: A biomechanical investigation of locked versus nonlocked diaphyseal fixation in a human cadaveric model of nonosteoporotic and osteoporotic distal femoral fractures.

The objective of this study was to compare the biomechanical properties of locked and nonlocked diaphyseal fixation in a model of distal femur fractures using osteoporotic and nonosteoporotic human cadaveric bone. A supracondylar osteotomy was created to mimic a fracture (OTA/AO 33A3) in osteoporotic (n = 4) and nonosteoporotic (n = 5) cadaveric distal femurs. The left and right femurs of each pair were instrumented with a distal femoral locking plate and randomly assigned to have diaphyseal fixation with either locked or nonlocked screws. The construct was cyclically axially loaded, and construct stiffness and load to failure were evaluated. In osteoporotic bone, locked constructs were more stiff than nonlocked constructs (mean 143 vs. 98 N/mm when all time points combined, P < 0.001). However, in nonosteoporotic bone, locked constructs were less stiff than nonlocked constructs (mean 155 N/mm vs. 185 N/mm when all time points combined, P < 0.001). In osteoporotic bone, the average load to failure was greater in the locked group than in the nonlocked group (mean 1159 vs. 991 N, P = 0.01). In nonosteoporotic bone, the average load to failure was greater for the nonlocked group (mean 1348 N vs. 1214 N, P = 0.02). Bone mineral density was highly correlated with maximal load to failure (R2 = 0.92, P = 0.001) and stiffness (R2 = 0.78, P = 0.002) in nonlocked constructs but not in locked constructs. Contrary to popular belief, locked plating constructs are not necessarily stiffer than nonlocked constructs. In healthy nonosteoporotic bone, locked diaphyseal fixation does not provide a stiffer construct than nonlocked fixation. Bone quality has a profound influence on the stiffness of nonlocked (but not locked) constructs in distal femur fractures.

Biomechanical Investigation of the Osseointegration of Titanium Implants With Different Surfaces Placed With Allogeneic Bone Transfer.

Allogeneic grafts can be preferred to autogenous grafts in plastic and oral-maxillofacial surgery for vertical and horizontal bone deficiencies. Implant surface properties are an important factor in osseointegration. This study aims to evaluate the osseointegration levels of titanium implants with machined, sand-blasted, and acid-etched (SLA) and resorbable blast material (RBM) surfaces placed together with allogeneic bone tissue transplantations obtained from the tibia bone using biomechanical method. Twenty-five female Sprague-Dawley rats were included in the study. The rats were divided into groups in which machined (n=7), SLA (n=7), and RBM (n=7) surface implants were placed with the transplantation of bone taken from the tibia. Four rats (both left and right tibias) were used as donors. Grafts and implants were surgically placed in the corticocancellous part of the metaphyseal area of the tibia bones of rats. At the end of the 4-week experimental setup, all rats were killed, and the implants and surrounding bone tissue were subjected to biomechanical reverse torque analysis (N/cm). Sand-blasted acid-etched surface implants were observed to have higher biomechanical osseointegration levels than RBM and machined surface implants ( P <0.05). No statistical difference could be detected between the RBM and machined surface implants ( P >0.05). On the basis of the limited results of this study, it can be concluded that the osseointegration levels of SLA surface implants placed with allogeneic bone transplantation may be better than those of machined and RBM surface implants.