Inverter-based Shunt Active Power Filter Research Articles

3-level inverter based compensator for power quality enhancement using proposed Trianguzoidal PWM technique

In today’s scenario, the integration of a grid-connected load system with a hybrid energy system (HES) is encouraged to improve the reliability of the system. With the stunning rise in nonlinear loads in HES over the last two decades, the power quality (PQ) of the system has emerged as a paramount concern in contemporary times. The power quality problems include the injection of harmonics in the source current, low input power factor, poor voltage regulation, the burden of reactive power, etc. So, to mitigate these power quality problems in a single-phase distribution system, a 3-level Cascade H-bridge (CHB) inverter-based shunt active power filter (SAPF) is employed alongside a proposed Trianguzoidal pulse width modulation (TRZ PWM) strategy. The single-phase distribution system with SAPF is simulated in fixed and dynamic load conditions to check the system’s efficacy. The proposed PWM techniques for SAPF are compared with conventional PWM techniques, i.e., level shift, phase shift, and hybrid PWM techniques. Results indicate satisfactory performance of the proposed PWM techniques, exhibiting low harmonic distortion in source current, well within IEEE 519 limits, and high active filtering efficiency (AFE) compared to conventional PWM methods. Furthermore, this paper provides detailed comparisons of conventional and proposed PWM techniques in the context of active & reactive power supplied or delivered by load, source, and compensator, input power factor, harmonics in source or grid current, AFE, and individual harmonic components concerning fundamental component of source current.

Synergetic control for three-level voltage source inverter-based shunt active power filter to improve power quality

The present paper proposes a synergetic control (SC) with Phase-Locked Loop (PLL) technique for a three-phase three-levels neutral point clamped-voltage source inverter-based shunt active power filter (SAPF). This one is devoted to compensating for nonlinear load harmonics and reactive power to improve power quality in distribution power systems. SC strategy is known as a robust control with good performances in transient and steady-state performance. Furthermore, it does not require solving the state equations, nor knowing the poles of the system. The DC voltage, as well as the active filter currents, are controlled using SC strategies. The efficiency of the suggested strategy has been verified through simulation tests using Matlab/Simulink software, where the simulation results are analyzed for two scenarios: a diode bridge rectifier with RL load and RC load. The active power filter demonstrated outstanding performance in reducing harmonics, maintaining a dynamic response, and tracking DC voltage for both RL and RC loads, as revealed by the simulation results. By comparing the suggested control with the traditional control, we found that the former outperforms the latter in all aspects. This sheds light on the effectiveness of the suggested control.

An Enhanced Modified Multiport Interleaved Flyback Converter for Photovoltaic-Shunt Active Power Filter (PV-SHAPF) Applications

This paper presents a newly designed modified multiport interleaved flyback converter (MMPIFC) to transfer the photovoltaic (PV) power to the DC bus of the parallel-connected multilevel inverter-based shunt active power filter (SHAPF). The proposed modified multiport interleaved flyback converter (MMPIFC) is designed to interconnect N number of input power sources into the DC bus of the SHAPF to fix the problems with the partial shadow and improve the SHAPF’s ability to compensate. Compared to the commonly used interleaved flyback converter (IFC), the proposed MMPIFC has a larger boost factor toward the DC voltage input. The flow of power between the different power sources and SHAPF is controlled by varying the duty ratio of the main switches. The working principles of the proposed MMPIFC-operated PV-SHAPF are explored in this paper, and essential design concerns are highlighted. A prototype model with 1 kVA, 400 V, and 50 HZ is built and tested under various conditions to validate the theoretical analysis, design, and control method.

Time-domain harmonic extraction algorithms for three-level inverter-based shunt active power filter under steady-state and dynamic-state conditions-an evaluation study

Power quality is a major consideration in all office equipment, manufacturies and residential home appliances. Harmonic distortion is one of the crucial power quality issues. In order to mitigate the harmonic distortion, the performance of shunt active power filter (SAPF) is judged in terms of the accuracy and response time of its designed controller. In this context, the controller consists of three parts: harmonic extraction, switching control, and DC-link capacitor. The harmonic extraction technique serves the major role of deriving the required reference current to ensure successful mitigation of current harmonics by SAPF. Among the existing techniques, harmonic extraction algorithms based on time-domain approaches are most widely applied as they offer simple implementation features with increased speed and reduced computational burden. This paper presents detailed investigation and analysis regarding the performance of two famous time-domain harmonic extraction techniques namely, synchronous reference frame (SRF) and instantaneous power (PQ) theory. Extensive simulation work is conducted in MATLAB-Simulink platform under two conditions, which are, steady-state conditions and dynamic-state conditions, considering various highly nonlinear loads. For evaluation purposes, each control algorithm is incorporated into the controller of a three-phase SAPF, developed using a three-level neutral-point-clamped (NPC) inverter. Comprehensive results are provided to confirm mitigation performance of the SAPF utilizing each harmonic extraction algorithm.

Performance of three-phase three-wire cascaded H-bridge multilevel inverter-based shunt active power filter

<span lang="EN-US">Multilevel inverter (MLI) becomes more significant in Active Power Filter (APF) application due to capability to its produce low harmonic output current in which at the same time improving performance of APF. Among the topologies of MLI, Cascaded H-Bridge (CHB) is the most popular topology with less power devices requirement and simple design. MLI CHB is also capable to produce possible output voltage at twice of the number of DC source which in this case of APF is the best suited topology to replace with the conventional six -step inverter. This paper presents the performance of three- phase three-wire CHB MLI used in Shunt Active Power Filter (SAPF) based on Direct Current Control (DCC) and Indirect Current Control (ICC) schemes. Both schemes are developed and verified in MATLAB/Simulink. The simulation results show that both current control algorithms are capable to mitigate load current with Total Harmonic Distortion below than the permissible value based on IEEE 519 standard.</span>

PTF-based control algorithm for three-phase interleaved inverter-based SAPF

ABSTRACTIn this paper, modelling and hardware implementation of three-phase interleaved inverter-based shunt active power filter (SAPF) is proposed to mitigate current harmonics, reactive power for ensuring unity power factor and load balancing without shoot-through effect. Shoot-through effect is one of the hazardous issues in conventional voltage source inverters such as damage of power electronic switches, electromagnetic interference, ringing in the power circuitry. The present power system has inevitable non-linear loads which create large variations in the supply voltage distortions. Therefore, the compensation capability and efficiency of the SAPFs degrades. A novel predictive tuned filter is proposed in this paper to estimate the variations in the amplitude of supply voltage, frequency and harmonics for extracting the fundamental voltage signal. The fundamental extracted signal is further processed for reference current generation using generalized p-q theory. The performance of the proposed system is simulated using MATLAB®/Simulink environment and tested under different supply voltage conditions. The simulation results have been validated by developing a prototype in the laboratory by using a dSPACE1104 controller. It is found from the simulated and experimental results that the proposed system is fast, robust and accurate which improves the power quality without shoot-through problem.

Operation of Three-Level Inverter-Based Shunt Active Power Filter Under Nonideal Grid Voltage Conditions With Dual Fundamental Component Extraction

In this paper, a new reference current generation method is proposed for effective harmonics mitigation and reactive power compensation of three-level neutral-point diode clamped inverter-based shunt active power filter (SAPF) under nonideal grid voltage conditions. The proposed method is named as dual fundamental component extraction algorithm. In operation, the proposed algorithm extracts at the same time, the desired fundamental current and voltage components for generating reference current and synchronization phases, respectively. As a result, the proposed algorithm is able to generate reference current that ensures in phase operation of SAPF with the operating power system, without depending on any phase-locked loop elements. Besides, the proposed algorithm employs self-tuning filter (STF) for accurate computation of the fundamental components. Design concept and effectiveness of the proposed algorithm are thoroughly studied and evaluated in MATLAB–Simulink. Additionally, a laboratory prototype utilizing TMS320F28335 digital signal processor is built to validate its feasibility. Encouraging findings obtained from both simulation and experimental works demonstrate effectiveness of the proposed algorithm under both ideal and nonideal grid voltage conditions.

Cascaded Three Level Inverter Based Shunt Active Power Filter with Modified Three Level Hysteresis Current Control

A Cascaded three level inverter is controlled by using a three level HCC technique. The method has certain advantages compared to a two level HCC, such as a reduced switching frequency and a variation in switching frequency. However, this method suffers from tracking error in current due to dead zones provided between bands. This work aims at the development of modified three level hysteresis current controller (HCC) for a cascaded three level inverter-based shunt active power filter (SAPF) to mitigate the harmonics in a three-phase three-wire systems. Such method significantly reduces the current tracking error, the maximum switching frequency of the inverter as well as the variation in switching frequency. The simulation of the cascaded three level inverter-based shunt active power filter with a modified three level hysteresis current control is carried out in a PSIM environment for 2.5 kVA system. To validate the effect of degree of overlapping between the bands, two cases of a modified three level HCC are proposed. Both the cases are compared with conventional two-level HCC and three level HCC techniques. The simulation results show the effectiveness of the proposed scheme.

A Three-Phase Four-Leg Inverter-Based Active Power Filter for Unbalanced Current Compensation Using a Petri Probabilistic Fuzzy Neural Network

A three-phase four-leg inverter-based shunt active power filter (APF) is proposed to compensate three-phase unbalanced currents under unbalanced load conditions in grid-connected operation in this study. Since a DC-link capacitor is required on the DC side of the APF to release or absorb the instantaneous apparent power, the regulation control of the DC-link voltage of the APF is important especially under load variation. In order to improve the regulation control of the DC-link voltage of the shunt APF under variation of three-phase unbalanced load and to compensate the three-phase unbalanced currents effectively, a novel Petri probabilistic fuzzy neural network (PPFNN) controller is proposed to replace the traditional proportional-integral (PI) controller in this study. Furthermore, the network structure and online learning algorithms of the proposed PPFNN are represented in detail. Finally, the effectiveness of the three-phase four-leg inverter-based shunt APF with the proposed PPFNN controller for the regulation of the DC-link voltage and compensation of the three-phase unbalanced current has been demonstrated by some experimental results.

A Self-Tuning Filter-Based Adaptive Linear Neuron Approach for Operation of Three-Level Inverter-Based Shunt Active Power Filters under Non-Ideal Source Voltage Conditions

This paper presents a self-tuning filter (STF)-based adaptive linear neuron (ADALINE) reference current generation algorithm to enhance the operation of a three-phase three-level neutral-point diode clamped (NPC) inverter-based shunt active power filter (SAPF) under non-ideal (unbalanced and/or distorted) source voltage conditions. SAPF is an effective and versatile mitigation tool for current harmonics. As for its controller, ADALINE-based reference current generation algorithmd have widely been applied and proven to work effectively under balanced and purely sinusoidal source voltage conditions. However, no work has been conducted to study its performance under non-ideal source voltage conditions. In this work, a STF-based fundamental voltage extraction algorithm is integrated with an ADALINE algorithm, serving as synchronizer algorithm to ensure in-phase operation of the generated reference current with the non-ideal source voltage. Hence, it completely eliminates any dependency on conventional synchronizer algorithms such as phase-locked loop (PLL) and zero-crossing detector (ZCD). Additionally, the proposed STF-based ADALINE algorithm implements the modified Widrow-Hoff (W-H) weight updating algorithm for fast generation of reference current. Both simulation and experimental works are performed to verify design concept and effectiveness of the proposed algorithm. Comparative study with another recently reported algorithm is performed to investigate the performance improvement achieved by SAPF while using the proposed algorithm.

A Refined Self-Tuning Filter-Based Instantaneous Power Theory Algorithm for Indirect Current Controlled Three-Level Inverter-Based Shunt Active Power Filters under Non-sinusoidal Source Voltage Conditions

In this paper, a refined reference current generation algorithm based on instantaneous power (pq) theory is proposed, for operation of an indirect current controlled (ICC) three-level neutral-point diode clamped (NPC) inverter-based shunt active power filter (SAPF) under non-sinusoidal source voltage conditions. SAPF is recognized as one of the most effective solutions to current harmonics due to its flexibility in dealing with various power system conditions. As for its controller, pq theory has widely been applied to generate the desired reference current due to its simple implementation features. However, the conventional dependency on self-tuning filter (STF) in generating reference current has significantly limited mitigation performance of SAPF. Besides, the conventional STF-based pq theory algorithm is still considered to possess needless features which increase computational complexity. Furthermore, the conventional algorithm is mostly designed to suit operation of direct current controlled (DCC) SAPF which is incapable of handling switching ripples problems, thereby leading to inefficient mitigation performance. Therefore, three main improvements are performed which include replacement of STF with mathematical-based fundamental real power identifier, removal of redundant features, and generation of sinusoidal reference current. To validate effectiveness and feasibility of the proposed algorithm, simulation work in MATLAB-Simulink and laboratory test utilizing a TMS320F28335 digital signal processor (DSP) are performed. Both simulation and experimental findings demonstrate superiority of the proposed algorithm over the conventional algorithm.

A Simplified Synchronous Reference Frame for Indirect Current Controlled Three-level Inverter-based Shunt Active Power Filters

This paper presents a new simplified harmonics extraction algorithm based on the synchronous reference frame (SRF) for an indirect current controlled (ICC) three-level neutral point diode clamped (NPC) inverter-based shunt active power filter (SAPF). The shunt APF is widely accepted as one of the most effective current harmonics mitigation tools due to its superior adaptability in dynamic state conditions. In its controller, the SRF algorithm which is derived based on the direct-quadrature (DQ) theory has played a significant role as a harmonics extraction algorithm due to its simple implementation features. However, it suffers from significant delays due to its dependency on a numerical filter and unnecessary computation workloads. Moreover, the algorithm is mostly implemented for the direct current controlled (DCC) based SAPF which operates based on a non-sinusoidal reference current. This degrades the mitigation performances since the DCC based operation does not possess exact information on the actual source current which suffers from switching ripples problems. Therefore, three major improvements are introduced which include the development of a mathematical based fundamental component identifier to replace the numerical filter, the removal of redundant features, and the generation of a sinusoidal reference current. The proposed algorithm is developed and evaluated in MATLAB / Simulink. A laboratory prototype utilizing a TMS320F28335 digital signal processor (DSP) is also implemented to validate effectiveness of the proposed algorithm. Both simulation and experimental results are presented. They show significant improvements in terms of total harmonic distortion (THD) and dynamic response when compared to a conventional SRF algorithm.

DC-Link Capacitor Voltage Regulation for Three-Phase Three-Level Inverter-Based Shunt Active Power Filter with Inverted Error Deviation Control

A new control technique known as inverted error deviation (IED) control is incorporated into the main DC-link capacitor voltage regulation algorithm of a three-level neutral-point diode clamped (NPC) inverter-based shunt active power filter (SAPF) to enhance its performance in overall DC-link voltage regulation so as to improve its harmonics mitigation performances. In the SAPF controller, DC-link capacitor voltage regulation algorithms with either the proportional-integral (PI) or fuzzy logic control (FLC) technique have played a significant role in maintaining a constant DC-link voltage across the DC-link capacitors. However, both techniques are mostly operated based on a direct voltage error manipulation approach which is insufficient to address the severe DC-link voltage deviation that occurs during dynamic-state conditions. As a result, the conventional algorithms perform poorly with large overshoot, undershoot, and slow response time. Therefore, the IED control technique is proposed to precisely address the DC-link voltage deviation. To validate effectiveness and feasibility of the proposed algorithm, simulation work in MATLAB-Simulink and experimental implementation utilizing a TMS320F28335 Digital Signal Processor (DSP) are performed. Moreover, conventional algorithms with PI and FLC techniques are tested too for comparison purposes. Both simulation and experimental results are presented, confirming the improvement achieved by the proposed algorithm in terms of accuracy and dynamic response in comparison to the conventional algorithms.

Enhanced Instantaneous Power Theory with Average Algorithm for Indirect Current Controlled Three-Level Inverter-Based Shunt Active Power Filter under Dynamic State Conditions

An enhanced harmonics extraction algorithm based on Instantaneous Power (PQ) Theory is proposed for indirect current controlled (ICC) three-level neutral point diode clamped (NPC) inverter-based shunt active power filter (SAPF). SAPF is famous in current harmonics mitigation for its flexibility in dealing with dynamic state conditions. As for its controller, PQ Theory has served the major role in harmonics extraction algorithm due to its simple implementation features. However, it suffers from serious time delay due to its dependency on sluggish numerical filters. Furthermore, the algorithm is mostly designed to suit the operation of direct current controlled (DCC) SAPF which requires the knowledge of actual SAPF current (injection current). This leads to inaccurate mitigation as the injection current does not possess the exact information on actual source current which suffers from switching ripples problems. Therefore, two major modifications are introduced involving the development of mathematical average algorithm to replace numerical filter for fundamental real power computation and the formation of mathematical current relationship to change DCC to ICC based operation. The proposed algorithm is developed and evaluated in MATLAB/Simulink. From the simulation results, significant improvement in terms of Total Harmonic Distortion (THD) and response time is presented in comparison to conventional algorithm.

Three-Level Inverter-Based Shunt Active Power Filter in Three-Phase Three-Wire and Four-Wire Systems

This paper presents a direct current-space-vector control of an active power filter (APF) based on a three-level neutral-point-clamped (NPC) voltage-source inverter. The proposed method indirectly generates the compensation current reference by using an equivalent conductance of the fundamental component using APF's dc-link voltage control. The proposed control can selectively choose harmonic current components by real-time fast Fourier transform to generate the compensation current. The compensation current is represented in a rotating coordinate system with chosen switching states from a switching table implemented in a field-programmable gate array. In addition, a three-phase four-wire APF based on a three-level neutral-point-clamped inverter is also presented. The proposed APF eliminates harmonics in all three phases as well as the neutral current. A three-phase three-wire NPC inverter system can be used as a three-phase four-wire system since the split dc capacitors provide a neutral connection. To regulate and balance the split dc-capacitor voltages, a new control method using a sign cubical hysteresis controller is proposed. The characteristics of the APF system with an LCL-ripple filter are investigated and compared with traditional current control strategies to evaluate the inherent advantages. The simulation and experimental results validated the feasibility of the proposed APF.