Internal Temperature Research Articles

Closed-Form Solutions of Injection-Driven Flow and Heat Transfer Inside an Inclined Horizontal Filter Chamber

Abstract The closed-form solutions of models provide operators and designers with a better understanding of how the systems perform practically, thus improving critical industrial production operations. Due to this importance, the case study at hand seeks to find closed-form solutions of the internal momentum and temperature variation during the filtration process to advance fluid purification. Lie group analysis is used to transform a system of equations representing the flow and heat transfer into a solvable system without changing the dynamics of the case study. The transformed solvable system is then integrated to find closed-form solutions of the internal velocity (momentum) and temperature variation. The obtained closed-form solutions are then used to analyze the effects of physical parameters arising from the process dynamics to find combinations of parameters that yield maximum permeates outflow. The analysis conveys that the internal fluid velocity increases when enhancing the permeation parameter and minimizing Reynolds number, wave speed parameter, and chamber height.

Finding Critical Factors for Developing Dynamic Models to Optimize Greenhouse Solar Dryer’s Environmental Conditions

This paper is focused on the formulation of a mathematical model for greenhouse solar dryer systems in the context of determining the principal drivers of efficiency of the solar dryer. The model was built by evaluating the correlation coefficients of each term and only those terms which had high levels of significance were retained. To test this model, experiments were replicated with measurements being taken in the different sections of the greenhouse to provide a large spectrum of the environmental conditions involved. The values of the technical coefficients are predicated on internal air temperature, humidity ratio and weight of the product with fixed scales, avoiding sophisticated complex models prone to overfitting. By using terms with high correlation, the model is less likely to be affected by outliers and total correlation or cross correlation is low, thereby making the model practical. The outcomes of this research, therefore, offer a scientifically viable and a practical approach to enhancing drying processes in greenhouse solar dryer systems.

Enhancing variant of uncertain significance (VUS) interpretation in neurogenetics: collaborative experiences from a tertiary care centre

BackgroundThe findings of variants of uncertain significance (VUS) on a clinical genetic testing report pose a challenge for attending healthcare professionals (HCPs) in patient care. Here, we describe the outcomes...

Novel SoC-Based FBG Calibration Method for Decoupled Temperature and Strain Analysis within LIB Cells

Abstract Internal temperature monitoring of battery cells can be very useful, as the core temperature can deviate significantly from that of the housing, especially in case of cells with a thick electrode stack. Conventional resistance temperature detectors can accurately measure temperature, but are limited to the outer surface of the cell due to induction effects. They are therefore not suitable for internal in situ measurements. Fiber Bragg grating (FBG) sensors are unaffected by the electric field as they operate by reflecting light. However, a specific difficulty is the distinction of temperature vs. strain effects as the grating is sensitive to both. In this work a calibration routine to separate the influences of temperature and strain in a lithium-ion battery cell is presented and examined for two multi-layer stack pouch cells (10 and 20 Ah). The obtained in situ temperature data reveal a difference of up to 2°C between center and cell housing at elevated discharge rate (4C) and a delay in detection of temperature peaks by the external sensor by 12 s. Strain data correlate with numbers of electrode layers in the stack and yield a stress of up to 27.3 MPa in the center of the 20 Ah cell.

Resonance-State Temperature Compensation Method for Ultrasonic Resonance Wind Speed and Direction Sensors

To achieve high-precision wind speed and direction measurements in complex environments, a resonance-state temperature compensation method is proposed based on an ultrasonic resonance principle. This method effectively addresses the issue of sound velocity compensation errors caused by the temperature difference between the internal and external environments when using an internal temperature sensor for temperature compensation. By utilizing an adaptive resonance-state tracking model, the resonance frequency shift issues under varying conditions such as altitude, pressure, and temperature are mitigated. This approach ensures that the resonance frequency is strongly correlated with temperature, enabling temperature compensation through resonance frequency alone, without the need for a temperature sensor. The experimental results indicate that the resonance frequency variation rate with temperature for the resonance-state temperature-compensated ultrasonic resonance wind speed and direction sensor is approximately 0.08 kHz/°C. The wind speed measurement accuracy is ±0.3 m/s (≤15 m/s)/±2.3% (15 m/s~50 m/s), which is superior to the measurement accuracy of traditional ultrasonic wind speed and direction sensors (±0.5 m/s (≤15 m/s)/±4% (15 m/s~50 m/s)). The consistency of wind speed measurement is ≤±0.3%, representing an improvement of approximately 3% compared to ultrasonic resonance wind speed and direction sensors without resonance-state temperature compensation.

Multi-Objective Optimization of Insulation Thickness with Respect to On-Site RES Generation in Residential Buildings

This paper investigates the optimization of insulation thickness with respect to the integration of renewable energy systems in residential buildings in order to improve energy efficiency, maximize the contribution of renewables and reduce life cycle costs. Using the DesignBuilder and EnergyPlus software, this study models a representative two-story residential building located in Athens, Greece. The building envelope features extruded polystyrene thermal insulation and windows with unplasticized polyvinyl chloride frames and low-e glazing. Six scenarios with hybrid renewable energy systems are analyzed, including air- and ground-source heat pumps, solar thermal systems and a biomass fired boiler, so as to assess energy consumption, economic feasibility and internal air temperature conditions. A Pareto-fronts-based optimization algorithm is applied to determine the optimal combination of insulation thicknesses for the walls, the roof and the floor, focusing on minimizing the life cycle cost and maximizing the percentage of renewable energy utilized. The results demonstrate that scenarios involving biomass boilers and solar thermal systems, both for heating and cooling, when combined with reasonable thermal protection, can effectively meet the recent European Union’s directive’s goal, with renewable energy systems contributing more than 50% of the total energy requirements, whilst maintaining acceptable internal air temperature conditions and having a life cycle cost lower than contemporary conventional buildings.

A study on the thermal behavior of coal gangue mountains under airflow influence based on MD and CFD simulations

The long-term accumulation of coal gangue can lead to an increase in internal temperature. If the temperature becomes excessive, it can cause spontaneous combustion, posing serious environmental risks. The process is significantly influenced by external airflow. This study analyzes the thermodynamic properties and oxidation heat release rate of coal gangue samples through laboratory experiments. Subsequently, molecular dynamics (MD) simulations are used to investigate the mechanism of oxidation heat release during the heating process of coal gangue under varying oxygen supply conditions. Based on these findings, a coupled three-field model for the heating process of coal gangue mountains is developed. Using computational fluid dynamics (CFD) methods, transient simulations are conducted to analyze the internal thermal behavior of coal gangue mountains under the influence of external airflow, clarifying the risks of spontaneous combustion. The results indicate that after reaching T2 (295.16 °C), coal gangue enters an accelerated oxidation phase, with an increased heat release rate, heightening the risk of spontaneous combustion. The oxidation heat release rate of coal gangue accelerates with rising temperature and oxygen concentration, entering a rapid reaction phase after 300 °C, with a sharp increase in reaction rate. Compared to N2, coal gangue surfaces exhibit stronger adsorption of O2, and temperature changes affect N2 diffusion more sensitively (O2 diffusion coefficient increases by 0.312 Å2/ps, N2 diffusion coefficient increases by 0.334 Å2/ps). The isosteric heat of O2 adsorption in coal gangue decreases significantly with increasing adsorption amount, and higher temperatures hinder competitive adsorption of O2. The temperature in the deep and foot areas of the coal gangue mountains is lower, while the middle and upper areas near the slope surface exhibit higher temperatures, indicating a higher risk of spontaneous combustion in these regions. When environmental wind speed is too high or too low, both the internal temperature of the coal gangue mountains and the area of spontaneous combustion risk zones decrease. At a wind speed of 3 m/s, the spontaneous combustion risk zone reaches its maximum area of 73.47 m2, but when the wind speed increases to 7 m/s, the risk area decreases to 65.72 m2.

Transparent, Sprayable Plastic Films for Luminescent Down‐Shifted‐Assisted Plant Growth

AbstractThe world's steadily growing population and global heating due to climate change are a threat to food security. To meet this challenge, novel technologies are needed to increase crop production in a sustainable way. In this work, the use of luminescent down‐shifting (LDS) materials based on molecular Eu3+‐containing polyoxotitanates for plant growth enhancement is investigated. Using a systematic design strategy to optimize down‐shifting properties, conversion of the ultraviolet spectral range to the photosynthetically active radiation (PAR) is achieved with quantum yields as high as 68%. The prototype Eu3+‐compound can be incorporated into water‐based acrylic varnish that can be spray‐coated onto existing greenhouses. Comparing coated with uncoated greenhouses, basil plants produce 9% more leaf dry weight per plant, and a highly significant 10% increase in individual leaf dry weight. The coating reduces the amount of transmitted PAR by 8% but has advantageous effects on diffuse radiation and in reducing the internal mean temperature. Although there is some uncertainty as to the contribution of down‐shifting, with the bulk of the increase probably being due to higher diffused light and the reduction in maximum daily temperatures, this study establishes a model for the design of LDS paints for real‐world agricultural applications.

Electrically Controlled Smart Window for Seasonally Adaptive Thermal Management in Buildings.

Smart windows offer a sustainable solution for energy-efficient buildings by adapting to various weather conditions. However, the challenge lies in achieving precise control over specific sunlight bands to effectively respond to complex weather changes and individual needs. Herein, a novel electrochromic smart window fabricated by integrating a self-assembled cellulose nanocrystals (CNCs) layer with an electrochromic poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid) (PEDOT:PSS) layer is reported, which exhibits high near-infrared transmittance, low solar reflectivity (26%), and infrared emissivity (20%) in winter, and low near-infrared transmittance, high solar reflectivity (91%), and infrared emissivity (≈94%) in summer. Interestingly, the material offers dynamic temperature control based on its photothermal properties, maintaining the internal temperature of buildings within a comfortable range of 20-25 °C from morning to night, particularly in winter with significant daily temperature fluctuations. Simulations show that the CNC-PED device demonstrates excellent energy-saving and CO2 emission reduction capacities across various global climate zones. This study presents a feasible pathway for constructing season-adaptive smart windows, making them suitable for energy-efficient buildings.

Permanent magnets with embedded phase changing material for electric motor thermal management

The magnetic performance of NdFeB permanent magnets rapidly decreases as their operation temperature increases. This limits the power output of electric motors as their internal temperature quickly increases with the power demand. This is particularly problematic for applications where high peak power is required for a short period of time, for example during automobile highway acceleration or during an airplane lift-off. With the advances in additive manufacturing, one can envision to fabricate more complex motor geometries and magnetic structures, without additional costs, allowing for enhanced functionalities such as better thermal management. In this context, this paper investigates the feasibility of using phase changing materials (PCMs) to mitigate the temperature rise in permanent magnets (PMs) fabricated by additive manufacturing. The potential of PCM and its relevance was validated by modeling the thermal response of an electric motor during a representative electric vehicle driving scenario. It was found that segmented magnets with embedded phase changing materials would allow to efficiently control temperature rise. To validate the simulation results, PM test pieces with and without embedded PCMs were fabricated using cold spray additive manufacturing and tested using a custom laser thermal cycling setup.

Thermal Evaluation of Solar Dryer’s Curve-Front utilized Heat Transfer Analysis

The sun is most sustainable renewable energy, environmentally friendly and utilized for preservation of food and agricultural crops. The main objective of this experiment research work has focused on using renewable energy for evaporated moisture of foods fruit vegetables and herbs by drying system. The heat transfer equation are analyzed to effectively harness the temperature from the sun. Experimental data obtained were used to evaluate the properties of dry air on boundary region condition. Initial, testing was carried out under without load condition, and the result shows that the ambient and dryer’s internal temperature range between 29.3-40.2˚C and 37.4-60.3 ˚C, respectively, in Thailand a latitude of 14°0'48.46" North and longitude of 100°31'49.76" East (recorded average solar radiations and temperature on January 2023 - June 2024), average solar radiations range between 312 W/m2 and 513 W/m2. The indirect natural convection was design and calculated energy base on average temperature not higher than 55˚C, utilized sun daylight at 08:00 a.m. to 04:00 p.m. local time and clear sky or partially cloudy. Second, determination of design parameters; heat energy equation and steam table analysis. Final, utilization of the design under local time, solar radiation and the climatic local conditions and test with ginger slices (represent product in order to examine weight loss). The solar dryer’s curve front shape conduced on without load showed the heat transfer coefficient natural convections range between 3.7 and 4.5 W/m2 ˚C, the energy of dry air analysis range between 54.7 and 155.2 J/s and performance of drying rate range between 0.06 and 0.82 g/s, under increasing and decreasing trends of solar radiations from the time, date and climatic local region condition.

Integrated all-fiber-optic sensor based on FPI and MZI composite structures for temperature and strain measurement

In this paper, a temperature and strain sensor based on fiber-optic Mach-Zehnder interferometer (MZI) cascaded with Fabry-Perot interferometer (FPI) is designed and fabricated. The integrated sensor structure consists of no-core fiber (NCF) sandwiched by two sections of multi-mode fiber (MMF), hollow-core fiber (HCF), and two single-mode fibers (SMF) which are cascaded at the ends of the MMF and the HCF. Due to the thermal expansion effect, thermo-optic and elasto-optic effects of fiber material, the increase of the temperature and strain will make the change of the transmission mode, which will cause the spectral fringes wavelength shifting with strain, and the intensity of the spectral fringes varying with temperature but not strain variations in multiple temperature ranges. The series experiments valid show that the sensor with integrated structure realizes the strain and temperature measurements in multiple temperature ranges, and the minimum and maximum temperature sensitivities are -0.278dBm/°C and -0.670dBm/°C in the temperature range of 68-86 °C and 123-141 °C, respectively. The strain sensitivity is 2.17pm/με all over the measured range. The integrated sensor structure has the advantages of high sensitivity, multiple measuring ranges, simple manufacturing, and low cost, which has the potential to be applied in the field of the internal strain and temperature measurements of different structures.

A new improvement to the characteristic equation method applied to different single-effect LiBr-H2O absorption chillers

The characteristic equation method was developed to be applied to absorption machines using characteristic equations to control and predict the thermodynamic performance of these machines. Since the conventional characteristic equation method was established, different approaches have been taken to improve the accuracy of the results of the characteristic equations. The Dühring parameter (B) represents a linear relationship between the internal boiling temperatures at a given concentration of solution and has usually been adopted as a constant fixed value in the characteristic equation method. The influence of the Dühring parameter (B) on the accuracy of the main results is important to the characteristic equation method and has not been analyzed further. This study analyzed this parameter in the characteristic equation method and a new approach to this method was proposed. This analysis gives a better insight into the influence of this parameter on the characteristic equation method and this approach provides a new use of this method to achieve better thermodynamic prediction and control of absorption chillers of different capacities under different operating conditions. The deviations between the fixed B value usually adopted for the LiBr/H2O solution and each value of the B obtained by the model at different concentrations of solution and internal temperatures affected the accuracy of the main results of the characteristic equations. An approach using a linear adjustment between B and the thrust temperature (Δtthrust) was put forward to reduce these deviations. The results of the characteristic equations were more accurate using this adjustment than using the fixed B value. Then, the characteristic equation method was applied to six LiBr/H2O single-effect absorption chillers using the proposed new approach. This approach was compared with the conventional method and with other main approaches. The heat removed (Q̇E) and COP results from the characteristic equations and the thermodynamic modelling were compared. All the average deviations using the proposed approach were less than 2 %, which represents an improvement in the accuracy of the results of the characteristic equations and gives a better prediction and control of absorption chiller performance. Therefore, the proposed approach contributed to improve the accuracy of the characteristic equation method in order to refine its application to absorption chillers.

Thermophysical properties of AlxCoCrCuFeNi high entropy alloys

The AlxCoCrCuFeNi (x = 0.25, 0.5, 1, 2) high entropy alloys (HEAs) were prepared by arc melting and spray casting techniques. Their microstructures, hardness, and thermophysical properties such as fusion enthalpy, entropy, thermal diffusion coefficients, thermal expansion coefficients, were investigated. XRD results indicated that AlxCoCrCuFeNi (x = 0.25 and 0.5) alloys were composed of a high-entropy FCC phase and Cu-rich nanophase. As the Al content increased to 1 and 2, the phase structures included the AlNi-rich B2 phase, FeCr-rich A2 phase and Cu-rich nanophase. With the increased Al content, the microstructures of AlxCoCrCuFeNi HEAs transitioned from coarse dendrites to petal-like dendrites, and the grains were continuously refined. Moreover, the Al additions reduced the density whereas increased the Vickers hardness of the alloys. The maximum hardness observed in Al2CoCrCuFeNi HEA was approximately 2.4 times greater than that of the Al0.25CoCrCuFeNi HEA. The thermal diffusion coefficients of alloys initially increased and subsequently decreased as the temperature elevated. The phase transformation induced by Al content was an effective method for rapidly homogenizing the internal temperature of alloys. Furthermore, the crystal structure, elemental segregation, lattice distortion, enthalpy and entropy of fusion, and lattice vibration frequency all mutually affected the thermal diffusion and expansion coefficients of AlxCoCrCuFeNi HEAs.

Intelligent temperature measuring thermal spray multilayer thermal barrier coatings based on embedded thin film thermocouples

Thermal barrier coatings (TBCs) have garnered significant attention as crucial protective components for turbine blades. However, the current use of TBCs is limited by their singular functionality and the inability to accurately obtain the temperature gradient distribution within the coatings. Addressing the aforementioned issues, this paper proposes an intelligent thermal barrier coating embedded with thin-film thermocouples. This method not only provides effective thermal protection but also facilitates the precise measurement of the internal temperature gradient within the coating. To mitigate the thermal mismatch in TBCs under high-temperature environments, which can compromise their lifespan, this study employs multi-objective optimization of structural parameters to design an optimal coating thickness. This strategy ensures both superior thermal protection and extended service life. The intelligent temperature-sensing TBCs were fabricated using atmospheric plasma spraying and magnetron sputtering, followed by comprehensive characterization. To validate the performance of the intelligent temperature-sensing TBCs, static tests were conducted in a muffle furnace. The results demonstrated that the sensors exhibit excellent repeatability and high-temperature durability. Furthermore, a test platform replicating the thermal shock conditions of an engine environment was developed. This platform confirmed that the intelligent temperature-sensing TBCs are capable of accurately measuring the internal temperature gradient within the coating under engine-like conditions, offering a novel methodology for engine monitoring and diagnostics.

The fate for the interior content of a Black Hole from one-quarter entropy area-law

In this paper we continue investigations concerning the physical nature of the black hole entropy. In particular, in order to depict massless excitations (gravitons) leading to the one-quarter entropy area law, we use a mechanical statistical approach. As a first result, we obtain that, starting with a radiation field, we cannot exactly obtain the one-quarter factor in entropy area law. In the aforementioned framework, the correct black hole entropy is obtained only in the case where the internal temperature Ti, proportional to the Bekenstein-Hawking one, is such that Ti→0. As a consequence, according to other similar proposals in the literature, only a kind of Bose Einstein condensate (BEC) can exactly support the black hole entropy.

Security Length Associated with the Risk of Ammonia Tank Leak Using CTOA Criterion and ALOHA Software

Ammonia is a toxic gas and can cause tragic consequences for humans. The damage level depends on concentration and duration of exposure. The security length associated with the risk of a tank leak at the acute exposure level of 30 ppm (AEGL-1) has been computed. Two tools have been combined: the CTOA criterion and the ALOHA software. The CTOA, a measure of fracture resistance against ductile crack propagation, is implemented in Abaqus software to compute the size of a breach in a tank submitted to internal pressure. This breach is assumed to be initiated by a gouge-dent defect provoked by a shock. The ALOHA software introduces the tank's characteristics, contents, and breach size. This allows us to determine and visualize the security length. The security length depends on geographic and climatic conditions, and for an incident localized in Metz (France), a value of 436 m was found. The effects of internal temperature, wind speed, and breach position are studied. A comparison for the same reference state with hydrogen is also made.

Behavioural thermoregulation prevents thermal stress in lizard sperm fertility

Global warming is threatening ectotherms, with strong repercussions on their population dynamics. Body temperature in ectotherm reptiles is crucial to perform all their biological functions, which are maximized within a narrow interval. When faced with new or adverse thermal conditions, reptiles will respond with distributional changes, behavioural adjustments to maintain their internal temperature, or by adapting to the new environment, otherwise, extinctions will occur. Higher temperatures may have negative repercussions, for example, shortening periods of activity, affecting embryo development during gestation or decreasing viability of sperm cells in males. Through behavioural thermoregulation, reptiles can compensate for environmental variations (Bogert effect). Furthermore, according to Janzen’s hypothesis, the physiological cost of responding to adverse thermal conditions will be low in species exposed to higher thermal overlap. Here, we analysed the effect of a change in the thermal regime on sperm cell viability in Sceloporus megalepidurus, a small viviparous lizard from central Mexico. We hypothesized that an active thermoregulator inhabiting temperate mountains is able to prevent the effects of thermal change on sperm cell viability. We found that the change in thermal regime did not modify sperm cell viability, nor does it affect the maturation of sperm cells in the epididymis. Our results support the Bogert effect and suggest that, despite the high temperatures and low thermal quality, S. megalepidurus can maintain its body temperature within an optimal range for sperm cell viability.

Differential expression of hemolymph proteins in wild bumblebees provides insights into species‐specific impacts of heat stress

AbstractWildlife faces an increasing threat from extreme climatic events, such as heatwaves, which can have a severe impact on various species, including crucial pollinators like bumblebees. Bumblebees are cold‐adapted and heterothermic, possessing the ability to regulate their internal temperature. The impact of heat stress seems species specific in bumblebees. While most species are impacted, some bumblebee species manage to survive, potentially by employing physiological mechanisms, including the modulation of their protein profile (e.g. Heat Shock Proteins). However, there is limited understanding of how their protein profiles are associated with heat exposure. In this study, we examined the global variation in the protein profile of males from two bumblebee species sampled in the wild: the heat‐tolerant Bombus terrestris and the heat‐sensitive Bombus magnus. After subjecting them to heat stupor at 40°C in controlled condition, it was observed that nearly all B. terrestris survived the stress, while over 50% of B. magnus individuals succumbed to the heat exposure. Through off‐gel bottom‐up proteomics and LC–MS/MS analysis of the hemolymph proteome, we identified 164 proteins in both species with a large part of differentially expressed proteins after heat exposure. Additionally, quantitative analysis of fat bodies revealed that the relative mass was stable in B. terrestris, while it was significantly lower in B. magnus exposed to heat stress. Our data suggest that compared with B. magnus, B. terrestris displays a higher adaptability of its hemolymph proteome in response to heat stress. This adaptability could be a key factor contributing to the high physiological resistance of B. terrestris and its ability to adapt to new, stressful environments expected due to climate change. Understanding these mechanisms of protein regulation in bumblebees could provide valuable insights into their resilience and vulnerability facing environmental stresses.

Evaluation of Reusable Thermal Protection System Materials Using a High-Velocity Oxygen Fuel Torch.

We studied a candidate TPS (thermal protection system) material for reusable re-entry space vehicle applications. The material was based on a high-temperature-resistant material called Cerakwool. A total of six specimens were fabricated with substrate densities of 0.45 g/cm3, 0.40 g/cm3, and 0.35 g/cm3, with two specimens for each density. All specimens were coated with high-emissivity TUFI (toughened unpiece fibrous insulation), with coating thicknesses ranging from 445 to 1606 µm. The specimens were tested using an HVOF (high-velocity oxygen fuel) material ablation test facility. For each density specimen pair, one specimen was tested at 1 MW/m2 and the remaining one was tested at 0.65 MW/m2. The average stagnation point temperature for specimens tested at 1 MW/m2 was ~893 °C, approximately 200 °C higher than those tested at 0.65 MW/m2. This suggests a ~200 °C increase in stagnation point temperature for a 0.35 MW/m2 rise in incident heat flux. During the tests, internal temperatures were measured at three locations. For all tested specimens, regardless of heat flux test conditions and density, the temperature at ~40 mm from each specimen's stagnation point remained around or below 50 °C, well within the 180 °C design limit set for the TPS back face temperature. Post-test visual inspections revealed no signs of ablation or internal damage, confirming the material's reusability.