Internal Fracture Research Articles

Development characteristics and controlling factors of fractures in lacustrine shale and their geological significance for evaluating shale oil sweet spots in the third member of the Shahejie Formation in the Qikou Sag, Bohai Bay Basin

Natural fractures are critical for shale oil and gas enrichment and development. Due to the extremely high heterogeneity of shale, the factors controlling the formation of internal fractures, especially horizontal fractures, remain controversial. In this study, we integrate thin section analysis and micro-computed tomography (CT) data from several lacustrine shale samples from the third member (Es3) of the Shahejie Formation, Qikou Sag, Bohai Bay Basin, to assess the fractures in detail. The goal is to reveal the development characteristics, controlling factors, and geological significance for evaluating sweet spots in a shale oil play. The fractures in the Es3 contain high-angle structural and horizontal bed-parallel fractures that are mostly shear and extensional. Various factors influence fracture development, including lithofacies, mineral composition, organic matter content, and the number of laminae. Structural fractures occur predominantly in siltstone, whereas bed-parallel fractures are abundant in laminated shale and layered mudstone. A higher quartz content results in higher shale brittleness, causing fractures, whereas the transformation between clay minerals contributes to the development of bed-parallel fractures. Excess pore pressure due to hydrocarbon generation and expulsion during thermal advance can cause the formation of bed-parallel fractures. The density of the bed-parallel and structural fractures increases with the lamina density, and the bed-parallel fractures are more sensitive to the number of laminae. The fractures are critical storage spaces and flow conduits and are indicative of sweet spots. The laminated shale in the Es3 with a high organic matter content contains natural fractures and is an organic-rich, liquid-rich, self-sourced shale play. Conversely, the siltstone, massive mudstone, and argillaceous carbonate lithofacies contain lower amounts of organic matter and do not have bed-parallel fractures. However, good reservoirs can form in these areas when structural fractures are present and the source, and storage spaces are separated.

Augmentative lag screws as a treatment for aseptic hypertrophic nonunion after internal fracture fixation

BackgroundHypertrophic nonunion after intramedullary (IM) nailing and plating is Uncommon and the treatment remained controversial. The aim of this study was to show the result of a simple augmentative lag screws technique for vital non-unions after internal fixation Patients and methodsWe retrospectively reviewed the patients with nonunion after internal fixation between January 2016 to August 2022. Patients with unacceptable shortening or deformity were excluded as well as nonunion septic cases. All the patients were followed up for at least 6 months. ResultsSeven patients achieved bony union in a median time of 12 weeks (IRQ 12–16). There was a failure case with persistent non-union and brokerage of the screws. DiscussionVarious techniques have been described to treat non-union after intramedullary nailing or plating. The existing nail is frequently removed, and the non-union site is either re-reamed and re-nailed or fixed with a plate or external fixation devices or rechanged by a nail in the case of plates. In our study of non-union, augmentative lag screws were successfully applied to treat eight patients with aseptic nonunion, resulting in the healing of non-union in all cases except one. ConclusionAugmentative lag screws represent a simple technique for the management of aseptic hypertrophic nonunion after internal fixation with a significantly shorter operating time.

Hot Work Mold Repaired via Hot Isostatic Pressing towards High Red Hardness

Repairing hot work molds can extend their lifespans and reduce the production costs. This study presents a proposed method for enhancing the red hardness and strength of repaired molds. The method involves utilizing PM23 high-speed steel powder to repair H13 steel molds with two distinct surface states through the process of hot isostatic pressing (HIP). The internal microstructure changes, bonding state, fracture morphology, and crack extension behaviors of the repaired molds are characterized using scanning electron microscopy and electron backscatter diffraction technology. Additionally, the mechanical properties, including red hardness and tensile strength, are quantitatively analyzed. The findings indicate that the repaired area in the sandblasted sample exhibits a rough and uneven structure, demonstrating exceptional toughness. The tensile strength of the repaired region is approximately 1195.42 MPa, while the hardness measures around 672.8 HV. These properties effectively enhance the performance of the molds. The experimental findings indicate that HIP can effectively restore molds, resulting in enhanced red hardness and improved toughness, particularly when combined with sandblasting as a pretreatment method.

Numerical Study on the Damage Characteristics of Layered Shale Using 3D DEM

Layered shale is a kind of rock with obvious anisotropy, which is significantly influenced by the inclination angle of the rock. In this study, the influence of bedding dip on the strength characteristics, failure mode, and internal fracture evolution of layered shale was investigated through laboratory triaxial compression tests and three-dimensional discrete element numerical simulations. Results show that the numerical model of layered shale constructed using the bonded block model can simulate the layered shale in terms of U-shaped strength variation and failure modes very well. Based on the distribution of cracks and failure characteristics of layered rocks, the failure modes of layered rocks are classified as follows: Shear failure across the bedding plane, slip failure along bedding planes, combined tensile splitting and shear failure. The development of microcracks damage in the slip failure model is controlled by interlayer joints, while in other failure modes, it is jointly controlled by the rock matrix and interlayer joints. The relationship between microscopic joint parameters and the variations of Young's modulus and peak strength has been proposed.

Dynamic strength characteristics of fractured rock mass

Fractures play crucial role in the behavior of rock masses, yet the understanding of their natural distribution and impact on dynamic characteristics remain unclear. Here the effect of “natural” fractures on the dynamic impact strength of rock mass was investigated using numerical specimens with fractures prepared using the Split Hopkinson Pressure Bar (SHPB) model. These fractures were generated through biaxial compression simulation. Various axial stress levels and confining pressures replicated diverse natural rock fracture distributions. To capture the anisotropic distribution of fractures in natural rock and the randomness of impact direction, impact from 0°, 90°, 180° and 270° directions were imposed. The biaxial loading simulation showed that fracture increases with higher loading stress, and rapidly expands in the post-peak stress stage, with ∨ or ∧ shaped slip plane depending on confining pressure. The impact strength of the fractured specimen decreases as the number of prefabricated fractures increases, following a two-stage pattern, i.e., rapidly decrease with small number of fractures and gradually decrease with high number of fractures. Pre-existing fractures aligning with the impact direction provide stronger resistance compared with fractures deviated, and their location and distribution significantly affect the stress transmission. The impact from other directions has different stress transmission routes related to the fracture and macroscopic surface distribution. Importantly, a specimen’s loading history shapes its internal fracture distribution, thereby affecting its resistance to impact stress. This research provides invaluable insights into the role and mechanics of fractures in rock masses, thus enhancing our understanding of rock dynamics and potentially informing more effective geotechnical engineering practices.

An XFEM-based CZM Numerical Strategy for Modeling Hydraulic Fracture Propagation under Different Fracturing Schemes

Segmented and cluster fracturing can improve the efficiency of volume stimulation in shale reservoirs and reduce construction costs. It is important to clarify the propagation characteristics of hydraulic fractures and stress interference under different fracturing techniques to optimize the process of clustered and staged fracturing. For this purpose, we have developed a 2D XFEM-based CZM hydraulic fracturing model. The capability of this model was validated by analytical solutions and then used to study the propagation paths of hydraulic fractures and the characteristics of stress interference under simultaneous fracturing, sequential fracturing, zipper fracturing and multi-cluster fracturing. The results show that in simultaneous fracturing, the middle cluster is compressed by the external position clusters, and the opening width of hydraulic fractures is reduced. In sequential fracturing, the fracture that first initiates create an additional stress field that inhibits the propagation distance of subsequent fractures and the propagation path of hydraulic fractures is also affected in the stress shadow region. Zipper fracturing can effectively alleviate stress interference between multiple fractures, and internal fractures can also propagate a certain distance. In multi-cluster fracturing, the fluid rate into the internal fractures may be limited, and fracture propagation is also limited by stress interference. Therefore, it is necessary to optimize the parameters of clusters to ensure that all clusters can initiate fractures normally. The research results are important for the parameter optimization of clustered and staged fracturing, especially for well factory fracturing mode.

Experimental Study on Mode I Fracture Characteristics of Granite after Low Temperature Cooling with Liquid Nitrogen

Liquid nitrogen fracturing has emerged as a promising technique in fluid fracturing, providing significant advantages for the utilization and development of geothermal energy. Similarly to hydraulic fracturing in reservoirs, liquid nitrogen fracturing entails a common challenge of fluid–rock interaction, encompassing the permeation and diffusion processes of fluids within rock pores and fractures. Geomechanical analysis plays a crucial role in evaluating the transfer and diffusion capabilities of fluids within rocks, enabling the prediction of fracturing outcomes and fracture network development. This technique is particularly advantageous for facilitating heat exchange with hot dry rocks and inducing fractures within rock formations. The primary objective of this study is to examine the effects of liquid nitrogen fracturing on hot dry rocks, focusing specifically on granite specimens. The experimental design comprises two sets of granite samples to explore the impact of liquid nitrogen cooling cycles on the mode I fracture characteristics, acoustic emission features, and rock burst tendency of granite. By examining the mechanical properties, acoustic emission features, and rock burst tendencies under different cycling conditions, the effectiveness of liquid nitrogen fracturing technology is revealed. The results indicate that: (1) The ultimate load-bearing capacity of the samples gradually decreases with an increase in the number of cycling times. (2) The analysis of acoustic emission signals reveals a progressive increase in the cumulative energy of the samples with cycling times, indicating that cycling stimulates the release of stored energy within the samples. (3) After undergoing various cycling treatments, the granite surface becomes rougher, exhibiting increased porosity and notable mineral particle detachment. These results suggest that the cyclic application of high-temperature heating and liquid nitrogen cooling promotes the formation of internal fractures in granite. This phenomenon is believed to be influenced by the inherent heterogeneity and expansion–contraction of internal particles. Furthermore, a detailed analysis of the morphological sections provides insights into the structural changes induced by liquid nitrogen fracturing in granite samples.

Tectonic Control on Shale Pore Structure and Gas Content from the Longmaxi Formation Shale in Southern Sichuan Basin, China: Insights from Fractal Analysis and Low-Pressure Gas Adsorption

Tectonic deformation of different intensities significantly controls shale pore structure, seepage channels, and gas content. The Longmaxi Formation shales in the southern Sichuan Basin have experienced multi-stage tectonic movements, resulting in a diverse fracture system and tectonic deformation. This study focuses on three representative tectonic morphologies: deeply buried strongly deformed (DBSD), deeply buried weakly deformed (DBWD) and shallowly buried weakly deformed (LBWD). We investigated the pore structure characteristics and heterogeneity of these shales under various tectonic conditions using total organic carbon (TOC) content, X-ray diffraction (XRD), scanning electron microscopy (SEM), a low-pressure N2/CO2 adsorption experiment (LP-N2/CO2 GA), and multi-scale fractal theory. The results reveal that strong tectonic compression and deformation conditions lead to the compression and flattening of organic pores by brittle minerals, resulting in long, oriented OM pores. Fracturing of brittle pore creates multiple internal fracture systems linked to dissolution pores, forming a complex micro-fracture–pore network. With intense tectonic deformation, mesopores tend to be compressed, increasing micropore pore volume (PV) and surface area (SA). The DBSD shale exhibits the highest micropore heterogeneity, while the LBWD shale shows the lowest heterogeneity. Fractal analysis indicates a significant decrease in micropore fractal dimension (Df) with increasing burial depth. In contrast, the surface and matrix fractal dimensions (Ds and Dm) of low-buried shale micropores and meso-macropores align vertically. Shale reservoirs in tectonically stable regions exhibit more favourable gas-bearing characteristics than strongly tectonically deformed areas. The LBWD has stable tectonic conditions that are favourable for shale gas preservation. Conversely, slip faults under deep burial conditions lead to extrusion and deformation of shale pore space, ultimately compromising the original reservoir capacity and hindering shale gas enrichment. These findings contribute significantly to our understanding of pore structure and heterogeneity in tectonically deformed shale reservoirs, providing invaluable guidance for the exploration, development, and prediction of shale gas resources.

Evaluation of the treatment of distal radial volar fracture by different methods sparing the pronator quadratus

ObjectiveThe traditional volar approach requires the release of the pronator quadratus (PQ) muscle in the treatment of distal radius fractures. However, intraoperative repair of the PQ muscle often fails due to tissue injury and unstable muscle repair. This study compared the outcomes of different methods of sparing the PQ muscle combined with the volar plate in treating distal radius fractures.MethodsA total of 95 patients with distal radius fractures sparing the PQ muscle were enrolled with the brachioradialis (BR) splitting approach (group A, 33 people), the volar plating insertion PQ muscle approach (group B, 35 people) and traditional Henry approach without sparing PQ muscle (group C, 27 people). Postoperative internal fixation, fracture healing and postoperative complications were observed in the three groups. The visual analog scale (VAS) of postoperative wrist pain was compared between three groups. The Dienst joint scale was used to evaluate the wrist function of patients, and imaging indexes were used to evaluate the surgical efficacy.ResultsA total of 95 patients with distal radius fractures were followed up for more than one year after surgery. All fractures obtained good union, with no vascular injury, nerve injury or wound infection. Outcomes at three days, one month and three months all showed no significant differences in postoperative imaging indexes among three groups and no significant differences in various indexes among three groups during the same period. The mean operative time in group C was significantly lower than that in groups A and B. There was significant difference in the mean operation time between group A and group B. The amount of mean operative blood loss or mean bone union time in groups A and B was significantly lower than those in group C. No significant difference was shown in mean operative blood loss or mean bone union time between group A and group B. No significant differences in limb function scores, VAS scores and the mean range of motion existed among three groups at the 12-month postoperative follow-up. However, outcomes assessed one week, one month and three months after surgery demonstrated significant differences in the VAS scores and the mean range of motion among three groups, and the group B had lower VAS score and greater the mean range of motion. According to Dienst score, the excellent rate in groups A, B and C was 91.0% (30/33), 94.2% (33/35) and 85.2% (23/27), respectively, at 12 months after surgery. Tendon irritation occurred in 2 cases and joint stiffness in 1 case in group A. In group B, there were 2 cases traumatic arthritis and 2 cases delayed carpal tunnel syndrome and 1 case tendon irritation. In group C, tendon irritation and delayed carpal tunnel syndrome occurred, respectively, in 3 cases.ConclusionOur results demonstrated that these two different surgical approaches were effective ways to reserve PQ and had good clinical outcomes. The volar plating insertion PQ muscle approach could reduce early postoperative pain, promote early activity and return to normal life, while the BR splitting approach was more advantageous in intraoperative fracture exposure and could shorten the operative time. However, some defects also existed. At 12 months of follow-up, no significant advantage was seen in sparing the PQ muscle. Therefore, surgeons should be aware of their individual characteristics and choose patients carefully.

Dynamic Compressive Mechanical Property Characteristics and Fractal Dimension Applications of Coal-Bearing Mudstone at Real-Time Temperatures

Coal-bearing rocks are inevitably exposed to high temperatures and impacts (rapid dynamic load action) during deep-earth resource extraction, necessitating the study of their mechanical properties under such conditions. This paper reports on dynamic compression tests conducted on coal-bearing mudstone specimens at real-time temperatures (the temperature of the rock remains constant throughout the impact process) ranging from 25 °C to 400 °C using a temperature Hopkinson (T-SHPB) test apparatus developed in-house. The objective is to analyze the relationship between mechanical properties and the fractal dimension of fractured fragments and to explore the mechanical response of coal-bearing mudstone specimens to the combined effects of temperature and impact using macroscopic fracture characteristics. The study found that the peak stress and dynamic elastic modulus initially increased and then decreased with increasing temperature, increasing in the 25–150 °C range and monotonically decreasing in the 150–400 °C range. Based on the distribution coefficients and fractal dimensions of the fractured fragments, it was found that the degree of damage of coal-bearing mudstone shows a trend of an initial decrease and then an increase with increasing temperature. In the temperature range of 25–150 °C, the expansion of clay minerals within the mudstone filled the voids between the skeletal particles, resulting in densification and decreased damage. In the temperature range of 150–400 °C, thermal stresses increased the internal fractures and reduced the overall strength of the mudstone, resulting in increased damage. Negative correlations between fractal dimensions, the modulus of elasticity, and peak stress could be used to predict rock properties in engineering.

Formation mechanism and evolution model of buried hill reservoir in BZ19‐6 structural belt, Bozhong Sag, Bohai Bay, East China

The BZ19‐6 structural belt is the largest buried hill oil‐gas‐bearing area recently discovered in Bohai Bay Basin. The formation and evolution of the buried hill reservoirs are complex. Presently, the development law and controlling factors of this reservoir is unclear. Based on 3D seismic, drilling data, thin section, and regional tectonic background, we explored the controlling factors and development law of the high‐quality buried hill reservoir. The results show that the buried hill reservoir can be vertically divided into a weathered glutenite zone, weathered fracture zone, internal fracture zone, and tight zone. The development of reservoir is mainly controlled by lithotypes, tectonic movement, and weathering. The rocks in the study area with low compressive strength, provided the material basis for the formation of fractures. The strongly reformed multi‐stage tectonic movements provides the external dynamics for the formation of fractures. Weathering further improved the physical properties of the reservoir. The buried hill reservoir is mainly distributed in the weathered fracture zone and internal fracture zone. Currently, natural gas mainly found in nearly E‐W‐trending and N‐S‐trending fractures. The nearly E‐W‐trending fractures are developed in the thrust nappe structure formed by N‐S‐trending extrusion in the Indosinian. The hinge zone of the structure is the main development area of fractures. The nearly N‐S‐trending fractures are associated with strike‐slip faults formed by sinistral strike‐slip stress in the Yanshanian. Under the background of NNE–SSW direction extensional stress during the Himalayan, early fractures were reactivated, opened and expanded, forming the reservoir space for later natural gas charging.

Fracture and porosity evolution of coal under uniaxial compression: An in-situ X-ray tomography study

To investigate the meso-structure evolution and fracture mechanism of coal under uniaxial compression, an X-ray three-dimensional scanning microscopy in-situ loading test bench was used to conduct a uniaxial compression test of coal. CT data were obtained under different strain conditions and combined using 3D visualization software. According to the surface porosity under different axial forces shows stages in the Z axis, the 3D reconstruction of coal was divided into three regions to compare its structural evolution law. The results show that the uniaxial compression of coal presents staged fractures, and the distribution characteristics of fractures and pores are closely related to internal stress propagation. With the axial force loading, the internal fractures continued to expand, accompanied by the generation of micro-fractures. The development degree of penetrating fracture and lateral strain in region 1 were always higher than in region 2 and region 3, which is more obvious after the scan D; During the whole process of uniaxial compression, the three regions interacted with each other, and the energy transferred between regions has a “hysteresis”. The failure response of region 1 to axial force was earlier than that in region 2, and region 2 was earlier than region 3. However, the fracture evolution behavior of the same region, the three regions showed consistency; After scan D, the meso-structure changes of region 1 were more significant than the other two regions; The coal was locally deformed and destroyed under the action of axial force, resulting in isolated pores and micro-fractures. The spatial distribution of pores and fractures, the existence of micro-fractures and the interaction among different regions aggravated the uneven distribution of axial force in coal, which has a great influence on the fracture process of coal, so that the failure of coal present stages.

Internal adaptation and mechanical properties of CAD/CAM glass fiber post-cores in molars: An in vitro study

ObjectiveThe purpose of this in vitro study was to evaluate the internal adaptation, fracture resistance, and fracture pattern of the residual roots and crowns of molars restored with computer-aided design/computer-aided manufacturing (CAD/CAM) glass fiber post-cores, and compare them with three other post-core restorations. Materials and methodsWe selected 32 extracted maxillary first molars and divided them into four groups according to the post-core system: traditional casting titanium (Ti) post-cores (TC group); Ti post-cores fabricated with selective laser melting (SLM group); CAD/CAM glass fiber post-cores of the split type (CCS group); and prefabricated glass fiber posts and composite resin cores (PF group). The internal adaptation was analyzed with microcomputed tomography. Teeth were restored with monolithic zirconia crowns and subjected to thermocycling and cyclic loading. A load was applied consistently along the long axis of the tooth until fracture to record the fracture resistance and pattern. For the statistical analysis, one- and two-way analyses of variance, Tukey's post hoc and chi-square tests were performed to compare the differences among the groups. ResultsThe CCS, TC, and SLM groups exhibited similar internal adaptations across all sections (P < 0.05). The FP group showed good fit with the root canals in the apical and middle sections but a poor fit with those in the cervical section. The fracture resistance was higher in the CCS, TC, and SLM groups compared to the PF group (P < 0.05). The proportions of restorable fractures in the CCS and PF groups were 62.5% and 50%, respectively. Unrestorable fractures were more frequent in the TC and SLM groups at frequencies of 100% and 87.5%, respectively. ConclusionThe internal adaptation and fracture resistance of the CCS group were similar to those of the TC and SLM groups, and the fracture pattern was mostly restorable, thus meeting the clinical requirements for molar post-core restorations. Clinical significanceCCS can be used to restore residual roots and crowns of molars and exhibit high efficacy in terms of adaptability and mechanical properties. More studies are required to evaluate the effectiveness of CCS.

Controlled Nano Cu precipitation through age treatment: a method to enhance the biodegradation, mechanical, antimicrobial properties and biocompatibility of Fe-20Mn-3Cu alloys.

Iron-manganese (Fe-Mn) based degradable biomaterials have been proven as a suitable substitute to permanent internal fracture-fixation devices. However, lower degradation and bacterial infection are still major concerns. To overcome these limitations, in this work, we have incorporated copper (Cu) in Fe-Mn system. The objective is to produce Cu nano-precipitates and refined microstructure through suitable combination of cold-rolling and age-treatment, so that degradation is improved eventually. High resolution transmission electron microscope (TEM) and scanning transmission electron microscope (STEM) confirmed the Cu rich composition of the nano-precipitates. Number of precipitates increased as aging time increased. Three-dimensional visualization of Fe, Mn and Cu atomic distributions using atom probe tomography (APT), indicated that Cu precipitates were in 15-50 nm range. Large number of nano-precipitates along with lower dislocation density led to highest strength (1078 MPa) and ductility (37 %) for the 6-hr age-treated sample. On the other hand, nano-precipitates and refined microstructure resulted highest degradation for the 12 hr of age treated sample (0.091 mmpy). When E.Coli bacteria was cultured with the sample extract, significantly higher antibacterial efficacy was observed for the sample having higher nano-precipitates. Higher degradation rate did not cause cyto-toxicity, rather promoted statistically higher cell proliferation (1.5 times within 24 hr) in in vitro cell-material interaction studies. In vivo biocompatibility of the alloy containing large nano-precipitates was confirmed from higher new bone regeneration (60%) in rabbit femur model. Overall study suggested that the optimization of the thermo-mechanical processes can effectively tailor the Fe-Mn-Cu alloys for successful internal fracture fixation. STATEMENT OF SIGNIFICANCE: : In the present work, we have reported a noble thermo-mechanical approach to simultaneously achieve Cu nano-precipitates and grain refinement in Fe-20Mn-3Cu alloy. Significant reduction in bacterial growth was observed in the sample containing high Cu precipitation. This is extremely significant in the present context. Cu nano-precipitates and grain refinement improved the degradation rate. Highest yield strength was observed after 12 hours of age treatment (493 MPa). We have theoretically calculated various factors of yield strength. High degradation rate did not cause cytotoxicity, rather promoted cell viability. We have reported that the released Cu ion concentration in vivo was not only below toxic limit, but also helped in new bone regeneration.

Simulation of hydrogen embrittlement of steel using mixed nonlocal finite elements

A new simulation strategy to model hydrogen embrittlement based on a multi-field finite element using displacements, pressure, volume variation, nonlocal damage variables and lattice hydrogen concentration as unknowns is proposed. The material is described using a modified GTN model, which includes the description of hydrogen enhanced decohesion (HEDE). The finite element problem is solved using a fully implicit formulation. Numerical problems related to volumetric locking are solved using a mixed pressure/volume variation formulation. The use of the mixed formulation allows a straightforward evaluation of the pressure gradient, which drives hydrogen diffusion. Mesh size dependence is solved using an implicit gradient nonlocal formulation. Two variables are used to represent damage: the plastic volume variation and the accumulated plastic strain, controlling nucleation. The model is used to simulate an existing experimental database (Moro et al., 2010; Briottet et al., 2012) including tensile, fracture toughness and pressurized disk tests. The model, after adjusting the various coefficients, can represent the main experimental findings: the effect of deformation rate on the failure of tensile specimens, the transition from surface to internal fracture with increasing deformation rate, the sharp toughness drop under hydrogen (CT specimen), the fracture location and the effect of the pressurization rate in the case of the tests on disks.

Strength prediction model of fractured dolomite and analysis of mechanical properties based on PFC3D

To investigate the mechanical properties of fractured dolomite, this study analyzed the fracture characteristics (dip angle, length, position, quantity) using the Pearson coefficient and MIC coefficient. Subsequently, the data pertaining to fracture characteristics is preprocessed using a third-degree polynomial, and a three-classification strategy is implemented to improve the logistic regression algorithm to establish the strength prediction model of fractured dolomite. Furthermore, the significance order of the impact of fracture characteristics on rock strength was determined using the numerical simulation software PFC3D, and the dip angle effect was explained from the perspective of internal fracture propagation within the rock. The results show that: (1) When the regularization coefficient λ = 10,000, the algorithm has the highest prediction accuracy and the strongest model generalization ability. (2) The numerical simulation analysis software PFC3D can accurately invert rock failure process and characteristics, and the order of influence of fracture characteristics on rock strength is dip angle > length > position.

A study of explosive-induced fracture in polymethyl methacrylate (PMMA)

The fracture response of geologic materials is of interest for applications, including geothermal energy harnessing and containment of underground explosions. To better understand the explosively induced fracture response of geomaterials, polymethyl methacrylate (PMMA) was used as a transparent rock surrogate to allow imaging of internal shock propagation and fracture growth processes. Experiments were conducted using high-speed shadowgraphy and photon Doppler velocimetry (PDV), which were compared to numerical simulations. Experiments measured fractures produced in 304.8mm×304.8mm×304.8mm PMMA cubes with two simultaneously initiated detonators. The cubes were subjected to varying amounts and directions of externally applied uniaxial stresses, including no stress, 2 MPa stress, and 20 MPa stress. The fracture radius as a function of time was extracted from the high-speed videos. Post-test images of the PMMA cubes aided in the determination of three-dimensional effects not directly imaged by the cameras. The surface velocity history and the shock response captured in PDV and the high-speed videos were compared to the simulated explosive-induced shock response. The simulation results indicate that the shock drives the fracture for the first 20 μs corresponding to a fracture radius of approximately 15 mm in the experiments. The gas-driven fracture extent was estimated analytically using an equilibrium stress distribution calculated after the shock wave propagation through the sample. Reduction in the gas pressure due to the leakage of the explosive products through the crack as a function of time was accounted for. The estimated fracture lengths were in agreement with the experimentally observed fracture lengths.

Anatomy of fractures: Quantifying fracture geometry utilizing X-ray computed tomography in a chalk-marl reservoir; the Lower Cretaceous Valdemar Field (Danish Central Graben)

Naturally fractured reservoirs tend to show heterogeneous permeability with open fractures enhancing the inherent diagenetic and depositional matrix fabric. Natural open fractures may function as pathways for fluid flow in tight (low matrix permeability) carbonate reservoirs and have a significant impact on the directions, magnitudes and heterogeneities of fluid flow and reservoir rock strength. Open fractures may however also facilitate the invasion of formation water while fractures that are partially or completely cemented can act as barriers to fluid flow. As a result, natural fractures significantly impact reservoir flow rates, anisotropy, storage, connectivity, recovery, and production. X-ray Computed Tomography (CT) offers a non-destructive technique to evaluate petrophysical parameters, such as porosity and permeability, and to assess the geometry, connectivity, and density of natural fractures, which are important constituents of chalk reservoirs. The purpose of this study is to investigate different types of naturally occurring fractures within the Lower Cretaceous succession of the Valdemar Field in the Danish North Sea. Six samples of core displaying at least one natural fracture on the surface are imagined; two samples of open fractures with plumose structure and hackle marks, three samples of shear fractures and finally one sample with deformation bands. The samples are imaged by CT and internal fractures are manually mapped. Image analysis provides detailed information on the fracture geometry in addition it indicates the presence of numerous microfractures hitherto not recorded in the Lower Cretaceous of the Danish North Sea. Core data show that fracture intensity can be significantly greater than calculated by conventional core interpretation techniques based on core surface observations. Further, apertures of both major and minor fractures are measured in CT images of all samples to determine if specific fracture types display characteristic that can distinguish them from other fracture types. As open fracture intensity increases, so too does permeability, likely enhancing reservoir connectivity on the field scale.

Study of rock damage characteristics in decoupled slit charge blasting based on computer tomography scanning

Controlling blast load damage and destruction of the remaining rock mass in rock blasting has been the focus of scientific research. By studying various decoupling ratios of the slit charges, blasting experiments and numerical calculations of the small charge were carried out on the glauconite specimen. The internal fracture and damage characteristics of the damaged specimens (post blast) were quantified by computed tomography (CT) scanning and three-dimensional (3D) model reconstruction. The results showed that the damage to the glauconite specimens was mainly radial, with the main crack surface in the slit direction and the “X-type” and “Y-type” non-slit directions. With the increase in the decoupling ratio of the slit charge, the fractal dimension of the explosion crack face tends to increase, and the degree of damage gradually increased; When the decoupling ratio was 1.67, the fractal dimension of the explosive crack surface decreased, the smallest degree of damage. LS-DYNA simulation software was used to study the dynamic fracture process and the effective stress peak of the blasthole wall in the slit and non-slit directions for different decoupling ratios of the slit charge. The numerical calculation results showed that with the increase in the decoupling ratio, the peak effective stress of the blasthole wall characteristic unit in the slit direction was larger than that in the non-slit direction; The effective stress peak showed an increasing trend, and the maximum peak effective stress was 567.7 MPa when the decoupling ratio was 1.67. Therefore, this method can be a suitable means to reconstructing the spatial distribution of internal cracks and numerical calculation to evaluate the damage mechanism of slit charge blasting; Furthermore, within the range of the optimal slit charge decoupling ratio, this method can guide the site to prevent the damage and destruction of the remaining rock mass, allowing for more, allocation and utilization of the explosion energy.

Biological reconstruction of bone defect after resection of malignant bone tumor by allograft: a single-center retrospective cohort study

BackgroundAllograft reconstruction following the resection of malignant bone tumors is associated with high rates of complications and failures. This study aimed to evaluate the efficacy and current problems of allograft reconstruction techniques to optimize treatment strategies at our center.Materials and methodsThirty-eight cases (16 men and 22 women), who were diagnosed with malignant bone tumors and had undergone allograft reconstruction, were recruited. Allograft was fixed by intramedullary nail, single steel plate, double plate, and intramedullary nail combined plate in 2, 4, 17, and 15 cases, respectively. Allograft union, local recurrence, and complications were assessed with clinical and radiological tests. Tumor grade was assessed using the Enneking staging of malignant bone tumors. Functional prognosis was evaluated by the Musculoskeletal Tumor Society (MSTS) scoring system.ResultsIntercalary and osteoarticular reconstructions were performed in 32 and 6 cases, respectively. Six patients underwent reoperation related to allograft complications, four patients had local recurrence, and three patients with allograft fracture underwent allograft removal. A total of eight host–donor junctions showed nonunion, including seven cases (18.4%) in diaphysis and one case (3.1%) in metaphysis (p < 0.01). Host rejection and secondary osteoarthritis occurred in nine and two cases, respectively. No deep infection and internal fixation device fracture occurred. The overall allograft survival rate was 81.6%. Postoperative MSTS score of patients with allograft survival was 26.8 ± 2.9, indicating a significant improvement as compared to their preoperative function.ConclusionsAllograft represents an excellent choice for intercalary bone defects after malignant bone tumor resection. Robust internal fixation protection across the whole length of the allograft is an important prerequisite for the survival of the allograft, while multidimensional osteotomy, intramedullary cement reinforcement, and pedicled muscle flap transfer can effectively improve the survival rate and healing rate of the allograft.