Intermediate Conditions Research Articles

How global sensitive is the AquaCrop model to input parameters? A case study of silage maize yield on a regional scale

IntroductionAquaCrop is a water-driven crop growth model that simulates aboveground biomass production in croplands. This study aimed to identify the driving parameters of the AquaCrop model for the model calibration and simplification to fill the research gap in intermediate environmental conditions between sub-tropical sub-humid and temperate sub-humid climates for silage maize.MethodsTo this end, we applied global sensitivity analysis (GSA) by combining the Morris method and the Extended Fourier Amplitude Sensitivity Test (EFAST) on crop yield output. The process involved a field sampling of soil and crop of silage maize carried out in the agricultural fields of Ghale-Nou, southern Tehran, Iran, in the summer of 2019 in order to measure certain model parameters.Results and discussionIn compliance with the Morris method, 30 parameters were identified as the least sensitive, while results from the EFAST test showed 9 parameters as contributing to the highest sensitivities in the model. The results clearly point to the capacity of employing a combination of both methods to attain a more efficient model calibration. Particular root, soil, canopy development, and biomass production parameters were influential and merit attention during calibration. Instead, parameters describing crop responses to water stress were acting rather insensitive in this study condition. The insights gained from this study, i.e., assessing parameter ranges and distinguishing between less sensitive and more sensitive parameters based on environmental and crop conditions, have the potential to be applied to other crop growth models with caution.

Pyrolysis of castor seed shells: Kinetic and thermodynamic study using thermogravimetric analysis (TGA)

The present work focused on the kinetics and thermodynamics of unexplored and unutilised material (Castor Seed Shells) at Slow and Intermediate Pyrolytic conditions. Thermogravimetric experiments were performed at two heating rate ranges i.e., at lower range (2.5–10 °C/min) and higher range (50–80 °C/min). The maximum devolatization observed below 500 °C, with the maximum weight loss ranging between 62 and 65 %. The average activation energy was determined to be 219.14, 217.42, 217.78, and 251.42 kJ/mol for the lower heating rate range, and 169.89, 171.27, 168.95, and 242.66 kJ/mol for the higher heating rate range, using Isoconversional methods including Kissinger-Akahira-Sunose, Flynn-Wall-Ozawa, Starink, and Friedman. Reaction mechanism along with thermodynamic parameters was also estimated. The CSS pyrolysis follows diffusional and nucleation reaction mechanism model and does not show significant change with the mode of pyrolysis.

Influence of Non-Melting Waste Plastics on Volumetric Properties and Performance of Asphalt Mixtures

The main objective of the study is to evaluate the impact of using polystyrene (PS) and polyethylene terephthalate (PET) plastics as an additive in asphalt mixtures. For this purpose, volumetric modification, moisture susceptibility along with performance variation at high, intermediate, and low temperature conditions were evaluated. Initially plastics were subjected to calorimeter analysis for assessing their melting characterization. Both PS and PET are included as dry mix additives individually at dosage levels of 3%, 6%, and 9% by weight of asphalt binder. Further, the changes in thermal properties of plastics occurring during mixture preparation were correlated to better understand the volumetric modification. PS, owing to its glass transition and partial amorphous nature, exhibited minimum deviation (<1%) from design air voids (4 ± 0.5%). PET was observed to increase the volumes of voids in mineral aggregate (VMA) and air void, owing to its crystalline nature. As regards performance, PS and PET modification enhanced the moisture resistance by 1.05 to 1.11 times the control mixture. The rutting tolerance index ( RTindex) value increased for all plastic modified mixtures from the indirect tensile asphalt rutting test (IDEAL RT) performed at 58°C. However, the intermediate temperature cracking tolerance index ( CTindex) at 19°C conveyed the high embrittled nature from plastic modification making the mixtures more susceptible to cracking. From the Gf versus l75 /m75 interaction diagram, it was conveyed that although addition of plastics improves the fracture toughness of asphalt mixtures, the ductile nature of mixtures is compromised. Also, PS and PET modification could not improve the ability of asphalt mixtures to resist thermal cracking, evaluated at −18°C.

Influence of the Dufour effect on striations formation in radio-frequency discharges

In recent years, interest in striation phenomena in radio frequency (rf) discharges has risen due to the availability of new experimental data and the implementation of new computational models. Depending on the conditions, different mechanisms of discharge striations are realized. These are the ionization instability, the instability due to the electron attachment to electronegative gases, or the instability due to thermoelectric transport. Although the first two mechanisms were modeled quite extensively in recent years, the understanding of the influence of the Dufour effect originating from plasma density gradients on the stability of radio frequency discharges in long tubes remains poor. In this paper, the influence of this mechanism on the longitudinal striations of radio frequency discharge is presented using a one-dimensional model of argon discharge driven with rf excitation under intermediate pressure conditions of 0.5 Torr. It is found that striation formation is sensitive to the value of the thermoelectric heat transport coefficient in the low electron temperature range. The critical value of this coefficient necessary for the instability onset is derived using the linear stability analysis.

A theoretical model for wave attenuation by vegetation considering current effects

A new theoretical model is derived to predict wave attenuation in an emerged vegetation domain under current influences by considering the current effects on changing both wave group velocity and energy dissipation rate. Considering the current effect on changing wave group velocity, the theory predicts an asymmetric behavior of wave decay in following and opposing currents, different from the earlier theory that predicts a symmetry decay behavior by ignoring the current effect on wave group velocity. The new theory dictates that as the current speed increases, the rate of wave decay changes from the traditionally reciprocal law to the exponential law, where the mixed exponential and reciprocal decay law exists under intermediate current conditions. Furthermore, the present theory can be reduced to an explicit expression of the drag coefficient for weak and strong current conditions. In addition, the theory shows that the decay rate depends on both incident wave amplitude and current velocity when the current velocity is relatively small to wave orbital velocity, whereas it is independent of incident wave amplitude when the current is strong. All of these wave decaying characteristics predicted by the theory have been confirmed by the available experimental data and the numerical results from a 2D RANS model (NEWFLUME).

SCADA based common bus regenerative control of PMSM drive for industrial application

AbstractThe emerging trend in sustainable industrial processes focuses on energy‐efficient drives to enhance performance in both intermediate and continuous operating conditions. For decades, researchers have focused on permanent magnet synchronous machines (PMSM) for industrial applications in order to retain consistency in performance and efficiency under wide speed ranges. Common bus regenerative control is an energy‐efficient method used in industrial systems to manage power flow between multiple devices on a shared DC bus. It captures and reuses excess energy generated during braking/deceleration, reducing waste and improving overall system efficiency. The experimental behavior of the drive scheme has been observed as per the standards of the laboratory. In this article, regenerative control of a PMSM drive is using the voltage vector control (VVC+) technique and the SCADA based condition monitoring for the PMSM drive system is integrated to supervise the parameters including current, voltage, power, speed, torque, and temperature under dynamic operating conditions. As a primary step of implementing the drive condition monitoring is carried out through Danfoss's motion control tool software. Further, the SCADA control system is interfaced to FC302 PMSM drive through RS485 Modbus communication to extract the necessary electrical attributes and monitor the same.

Genetic admixture between Central European and Alpine wolf populations

The recovery and expansion of formerly isolated wolf populations in Europe raise questions about the nature of their interactions and future consequences for population viability and conservation. Will fragmented populations fuse or maintain a certain level of isolation with migration? Central Europe is suitable for obtaining empirical data in this field as it represents a ‘crossroad' with the potential for contact among several phylogeographic lineages. In this study, non‐invasive genetic samples obtained during population monitoring in the Bohemian and Bavarian Forest (BBF) mountain ranges in the Czech Republic and Germany (Bohemian Massif) were analysed at different neutral markers including mitochondrial sequence, nuclear autosomal microsatellites and gonosomal sex markers. Resultant genetic profiles were compared with reference data to study population ancestry. Both cluster analyses of microsatellite genotypes and syntopic occurrence of haplotypes HW01 and HW22 showed genetic admixture between Central European and Alpine populations. This represents secondary contact and interbreeding of formerly allopatric populations with different phylogeographic histories and distant expansion centres in different biomes in the Baltic region versus the Apennine peninsula and Alps. Moreover, the study describes the founding event and genealogy of this admixed deme, inhabiting intermediate environmental conditions compared to parental forms, and emphasises the role of protected areas as stepping stones in the range recolonization process in endangered large mammals.

Diverse projected climate change scenarios affect the physiology of broccoli plants to different extents.

Climate change caused by global warming involves crucial plant growth factors such as atmospheric CO2 concentration, ambient temperature or water availability. These stressors usually co-occur, causing intricate alterations in plant physiology and development. This work focuses on how elevated atmospheric CO2 levels, together with the concomitant high temperature, would affect the physiology of a relevant crop, such as broccoli. Particular attention has been paid to those defence mechanisms that contribute to plant fitness under abiotic stress. Results show that both photosynthesis and leaf transpiration were reduced in plants grown under climate change environments compared to those grown under current climate conditions. Furthermore, an induction of carbohydrate catabolism pointed to a redistribution from primary to secondary metabolism. This result could be related to a reinforcement of cell walls, as well as to an increase in the pool of antioxidants in the leaves. Broccoli plants, a C3 crop, grown under an intermediate condition showed activation of those adaptive mechanisms, which would contribute to coping with abiotic stress, as confirmed by reduced levels of lipid peroxidation relative to current climate conditions. On the contrary, the most severe climate change scenario exceeded the adaptive capacity of broccoli plants, as shown by the inhibition of growth and reduced vigour of plants. In conclusion, only a moderate increase in atmospheric CO2 concentration and temperature would not have a negative impact on broccoli crop yields.

Arsenic in the groundwater aquifers of the Venetian Plain: geochemical modelling and occurrence of As-sulfides minerals, a review of data from the medio Brenta domain (Italy)

The Venetian Plain is known for areas with high concentrations of arsenic (As) in groundwater (up to more than 400 μg/L; exceptionally 647 μg/L, in selected areas). A study area was chosen, north of Padua, which exhibits typical residential, industrial, and agricultural characteristics similar to most Western countries and lacks hydrothermal, volcanic, or anthropogenic sources of arsenic. The pilot area was the focus of several studies which are reviewed in this note. The objectives of the studies were to verify the distribution of As concentrations in groundwater and sediments (mineralogical and geochemical analysis of groundwater sediments and of filtered and unfiltered groundwater) and to model the mobility of arsenic arising from water-rock interaction. The grain size of aquifer reservoirs includes gravel, sand, silt, and clay. The amount of organic matter in the aquifer sediments of the study area seems peculiar (higher) compared to other plains in the world; it influences the redox potential and the relative concentration of As in groundwater. Arsenic contamination in groundwater and redox conditions varied greatly in the area. Groundwater under oxidizing and highly reducing conditions had much lower arsenic concentrations compared to groundwater under intermediate reducing conditions. Arsenic minerals (such as realgar-pararealgar) occur in aquifer sediments and they were documented in the studied materials by different analytical techniques for the first time in the context of the Italian plains. Since these minerals are rare throughout the world in plain sediments not affected by volcanic or hydrothermal activity, their occurrence is a distinctive feature of the Venetian Plain aquifer. These arsenic minerals were found in peat sediments of the study area, consistent with geochemical modeling results, which require highly reducing conditions for their precipitation from groundwater. Modeling suggests that under oxidizing and up to slightly reducing conditions (from 200 mV to -50 mV), arsenic is adsorbed on solid phases, but a further decrease in redox potential leads arsenic desorption from solids and consequent groundwater contamination (from -50 mV to -250 mV). If the redox potential becomes even more negative (below -250 mV), geochemical conditions are favorable to the formation of arsenic sulfides. The precipitation of the realgar-pararealgar phases, predicted by the geochemical model, proceeds by extracting arsenic from the groundwater and quantitatively accounts for the lower arsenic concentration measured in the highly reducing groundwater of the study area.

Investigating tribological properties of electrophoretically deposited graphene nanoplatelets coatings on mild steel

The use of graphene-based materials to enhance the tribological properties of metal surfaces has garnered increasing interest in recent years. In fact, various studies have demonstrated that graphene-related materials, such as graphene nanoplatelets (GNPs), hold promise as solid lubricants. Electrophoretical deposition (EPD) is an interesting coating method to obtain a deposition of particles such as graphene as it is a simple, cheap and effective process with a low environmental impact. This study focusses on investigating the tribological properties of GNPs coatings obtained through anodic EPD on mild steel. Specifically, a combination of GNPs and deionized water as the deposition medium is introduced, allowing a cost-effective process with reduced environmental impact.Deposition time (5, 10 and 20 min) and concentration in the bath (0.5, 1 and 1.5 g/l) were varied in a full factorial plan to highlight their effects on coating performance. The coatings achieved demonstrated good adhesion with scratch break loads above 10 N and excellent tribological performances, with a friction coefficient of above 0.1. The results showed how concentration and process duration have two opposing effects on the adhesion and tribological characteristics of the coatings. The presence of an intermediate optimal condition, with 10 min deposition and a GNP concentration of 1 g/l, leading to an improvement in anti-wear properties of approximately 85 % and a coating break distance of over 80 m. An ANOVA analysis was developed to confirm the statistical significance of the process parameters in adhesion and tribology of the coatings.

CyberStatus: Responses to status manipulation and fears of positive and negative evaluations

Fear of positive evaluation (FPE) and fear of negative evaluation (FNE), which play distinct and central roles in social anxiety (SA), are postulated to reflect conflicting forces in hierarchal group contexts. Yet, experimental studies testing these assumptions are scarce. We examined the impact of status positions on FPE, FNE, and SA using a novel manipulation, CyberStatus. Participants (N = 557) provided self-descriptive statements before being randomly assigned to high, intermediate, or low-status conditions. Next, they reported their emotions, status, and belongingness-related cognitions and adjusted their self-presentation. FPE was more strongly linked to self-presentation modifications in the high- compared to intermediate-status conditions and positively associated with perceived status in the low vs. intermediate conditions. Furthermore, FPE and SA were more linked to belongingness in low vs. intermediate status conditions while FNE demonstrated the reversed pattern. These findings support and expand the evolutionary perspective on evaluation fears and emphasize the importance of assessing the linkage between status and belongingness systems in SA.

Eliciting expert judgements to underpin our understanding of faecal indicator organism loss from septic tank systems

Septic tank systems (STS) in rural catchments represent a potential source of microbial pollution to watercourses; however, data concerning the risk of faecal indicator organism (FIO) export from STS to surface waters are scarce. In the absence of empirical data, elicitation of expert judgements can provide an alternative approach to aid understanding of FIO pollution risk from STS. Our study employed a structured elicitation process using the Sheffield Elicitation Framework to obtain expert judgements on the proportion of FIOs likely to be delivered from STS to watercourses, based on 36 scenarios combining: (i) septic tank effluent movement risk, driven by soil hydro-morphological characteristics; (ii) distance of septic tank to watercourse; and (iii) degree of slope. Experts used the tertile method to elicit a range of values representing their beliefs of the proportion of FIOs likely to be delivered to a watercourse for each scenario. The experts judged that 93 % of FIOs would likely be delivered from an STS to a watercourse under the highest risk scenario that combined (i) very high STS effluent movement risk, (ii) STS distance to watercourse <10 m, and (iii) a location on a steep slope with gradient >25 %. Under the lowest risk scenario, the proportion of FIOs reaching a watercourse would likely reduce to 5 %. Expert confidence was high for scenarios that represented extremes of risk, while uncertainty increased for scenarios depicting intermediate risk conditions. The behavioural aggregation process employed to obtain a consensus among the experts proved to be useful for highlighting both areas of strong consensus and high uncertainty. The latter therefore represent priorities for future empirical research to further improve our understanding of potential pollution risk from septic tanks and in turn enable better assessments of potential threats to water quality in rural catchments throughout the world where decentralised wastewater systems are common.

Effect of acid treatment of eucalyptus fibers for improved poly(3-hydroxybutyrate) nanocomposites

Nanocomposites of poly (3-hydroxybutyrate) (PHB) containing fibrillated cellulose extracted from eucalyptus fibers were prepared and characterized. This study focuses initially on the method to follow the acid treatment of eucalyptus cellulose fibers (ECF) through an experimental design, where the studied parameters were the H2SO4 concentration, hydrolysis time, and reaction temperatures as independent variables for statistical analysis. The thermogravimetric analysis (TGA) of the ECF revealed that mild hydrolysis conditions shifted the degradation temperature of the fibers to higher values. The crystallinity index (CI) obtained by the X-ray diffraction was greater when intermediate hydrolysis conditions (30% H2SO4, 60 °C, 150 min) were employed. Afterward, the most promising ECFs hydrolyzed according to the experimental design were used to produce nanocomposites of PHB(ECF/PHB) containing 5 wt% of the fiber reinforcement via twin-screw mini extruder Haake MiniLab II operating at 180 °C, and varying the rotation speeds (60, 120, and 180 rpm). The ECF/PHB nanocomposites were characterized by TGA and dynamic mechanical analysis (DMA), through which the selected composites with higher thermal and mechanical properties were analyzed by differential scanning calorimetry (DSC), tensile test, and scanning electron microscopy (SEM). ECF/PHB nanocomposites processed at 120 rpm resulted in a material with improved properties. The DMA storage and loss moduli as well as the tensile elastic modulus increased 65%, 196% and 15%, respectively, as compared to the neat PHB. The SEM of the composites revealed nanowhiskers, microcrystalline and microfibrillated cellulose incorporated into PHB, which were attributed to improvements in the thermal and mechanical properties of the PHB matrix.

Assessment and characteristics of S-NPP VIIRS Deep Blue and Dark Target aerosol properties under clean, polluted and fire scenarios over the Amazon

The present study carries out the systematic performance evaluation of aerosol optical depth (AOD) products retrieved using Visible Infrared Imaging Radiometer Suite (VIIRS) Deep Blue (DB) and Dark Target (DT) onboard Suomi National Polar-orbiting Partnership (S-NPP) satellite over the Amazon Basin. Characteristics and uncertainty were evaluated under distinct air pollution scenarios such as a clean background in the wet season, polluted conditions in the dry season with biomass burning emissions and peak burning season with higher fire activity. VIIRS retrievals were also analyzed under aerosol loading, particle size and surface vegetation coverage against the Aerosol Robotic Network (AERONET) measurements at 9 sites in 2012–2022. VIIRS DB showed good accuracy, with 78% of AOD matchups falling within the expected error, 84% in the wet season, and 71% in the dry and burning seasons. In contrast, VIIRS DT indicated poor accuracy (64%) and trends overestimate the AOD in all air pollution scenarios. Both algorithms were sensitive to AERONET sites with high elevation and dark vegetated coverage characteristics. VIIRS DB and DT systematically overestimated AERONET AOD as increased aerosol loading. DB trends underestimate aerosol under background conditions and overestimate with coarse and fine particle predominance. Additionally, both algorithms indicated poor accuracy under forest type with a large positive bias. VIIRS DB demonstrated the highest accuracy in the presence of aerosol loading in sites characterized by mixed land cover type. This was observed in both coarse and fine mode scenarios for grassland. VIIRS DT demonstrated satisfactory accuracy under background conditions and dominance of coarse particles within grassland land cover type. For mixed land cover, satisfactory accuracy was found under intermediate aerosol loading conditions. DB algorithm showed greater uncertainty associated with the coarse particle aerosol for the full period and all polluted scenarios. Overall, VIIRS DT accuracy was more sensitive to varying air pollution scenarios.

Is Hybrid Work the Best of Both Worlds? Evidence from a Field Experiment

Abstract This paper reports causal evidence on how the extent of hybrid work—the number of days worked from home relative to days worked from office—affects employee attitudes and performance. Workers who spent around two days in the office each week on average self-reported greater work-life balance, more job satisfaction, and lower isolation from colleagues compared to workers who spent more or fewer days in the office. Employees in the intermediate hybrid condition received no different performance ratings compared to peers who spent more or fewer days in the office.

Effect of growth temperature on the microstructure and properties of epitaxial MoS2 monolayers grown by metalorganic chemical vapor deposition

Metalorganic chemical vapor deposition (MOCVD) is a promising technique for wafer-scale synthesis of MoS2 monolayers for 2D field-effect transistors (2D-FETs) and related devices. Epitaxial growth of MoS2 on sapphire provides films that are crystallographically well-oriented but typically contain low-angle grain boundaries (e.g., mirror twins), voids, and other defects depending on growth conditions and substrate characteristics. In this study, we investigate microstructure, optical properties, and field-effect characteristics of wafer-scale MoS2 monolayers grown by MOCVD on c-plane sapphire over a narrow window of growth temperatures (900–1000 °C). The density of low-angle grain boundaries in the MoS2 monolayer was found to decrease dramatically from 50% areal coverage for films grown at 900 °C to 5% at 1000 °C. This decrease in low-angle grain boundary density is correlated with an increase in the room-temperature photoluminescence intensity of A excitons and a decrease in the full-width-half maximum (FWHM) of the Raman A1g peak, which are typically indicative of a general reduction in defects in MoS2. However, the best transport properties (e.g., mean field-effect mobility mFE = 17.3 cm2/V s) were obtained in MoS2 monolayers grown at an intermediate temperature of 950 °C. It was found that as the growth temperature increased, small regions bound by high-angle boundaries begin to appear within the monolayer and increase in areal coverage, from ∼2% at 900 °C to ∼5% at 950 °C to ∼10% at 1000 °C. The growth temperature of 950 °C, therefore, provides an intermediate condition where the combined effects of low-angle and high-angle boundaries are minimized. The results of this study provide guidance on MOCVD growth and characterization that can be used to further optimize the performance of MoS2 2D-FETs.

Environmentally friendly assessment of ecological quality of watercourses based on banded demoiselle, Calopteryx splendens

AbstractDragonflies and damselflies are excellent bioindicators of the quality of both aquatic and terrestrial ecosystems. In our study, we assessed the usefulness of metric and meristic morphological traits as environmentally friendly and cost‐effective indicators of the integrative ecological quality of watercourses. Our study species of choice was the damselfly banded demoiselle, Calopteryx splendens (Harris) (Odonata: Calopterygidae). Adult C. splendens specimens were collected at three study sites along the trophic gradient of the Tisza River in Hungary and Ukraine. Body and abdomen length, head width, and distances between wing landmarks were assessed as metric traits, and the number of wing cells as meristic traits. The concentration of chlorophyll‐a was used to classify the three study sites into having a low, intermediate, and high trophic condition based on earlier studies. Significant differences were found along the trophic gradient based on the measured metric and meristic traits. Especially, insects from the site with the highest trophic condition had the largest body length, head width, and distances between wing landmarks, as well as the highest number of cells in the fore wings. There were also differences between males and females, but we did not find differences in fluctuating asymmetry (FA), i.e., differences between the left and the right wings. These results indicated that the morphological traits of adult banded demoiselles could be indicative of the environmental quality of a watercourse.

Null energy condition violation during inflation and pulsar timing array observations

Recently, evidence of stochastic gravitational wave background (SGWB) signals observed by pulsar timing array (PTA) collaborations, has prompted investigations into their origins. We explore the compatibility of a proposed inflationary scenario, incorporating an intermediate null energy condition (NEC)-violating phase, with the PTA observations. The NEC violation potentially amplifies the primordial tensor power spectrum, offering a promising explanation for PTA observations. Numerical analyses, primarily focused on NANOGrav’s 15-year results, reveal the model’s compatibility with PTA data. Notably, the model predicts a nearly scale-invariant GW spectrum in the mHz frequency range, which sets our scenario apart from other interpretations predicting a red primordial GW spectrum on smaller scales.

Topological phase transitions of generalized Brillouin zone

It has been known that the bulk-boundary correspondence (BBC) of the non-Hermitian skin effect is characterized by the topology of the complex eigenvalue spectra, while the topology of the wave function gives rise to Hermitian BBC with conventional boundary modes. In this work, we go beyond the known description of the non-Hermitian topological phase and find a different type of BBC that appears in generalized boundary conditions. The generalized Brillouin zone (GBZ) possesses non-trivial topological structures in the intermediate boundary condition between open and periodic boundary conditions. Unlike the conventional BBC, the topological phase transition is characterized by the generalized momentum touching of GBZ, which manifests as exceptional points. As a realization of our proposal, we suggest the non-reciprocal Kuramoto oscillator lattice, where phase slips accompany exceptional points as a signature of such topological phase transition. Our work establishes an understanding of non-Hermitian topological matter by complementing the non-Hermitian BBC as a general foundation of the non-Hermitian topological systems.

Association of chronic conditions and physical multimorbidity with new-onset incontinence in a nationwide prospective cohort study of older adults ≥ 50years in China.

The relationship between multimorbidity (i.e. ≥ 2 chronic conditions) and incontinence (i.e. urinary and/or faecal incontinence) is underexplored. This study investigated the association between multimorbidity and incident incontinence in Chinese adults aged ≥50years. Data from the 2011 and 2015 waves of the China Health and Retirement Longitudinal Study were used. The association between 12 chronic conditions, multimorbidity and new-onset incontinence was analysed using weighted logistic regression models. Mediation analysis was conducted to explore the potential mediators (self-reported health, subjective memory, depressive symptoms, disability, cognitive function, handgrip strength, mobility limitations, medications and frailty status) between multimorbidity and incontinence. Among 9,986 individuals aged ≥50years who were continent at baseline, 5.3% (n = 521) were newly incontinent 4years later (incident cases). The risk of incident incontinence increased with physical multimorbidity (OR 2.04, 95% CI 1.62-2.57). Compared to no chronic condition, having 1, 2, 3 and ≥ 4 chronic conditions were associated with incident incontinence with OR (95% CI): 1.41 (1.01-1.97), 1.74 (1.24-2.44), 2.82 (1.93-4.12) and 3.99 (2.29-6.95), respectively. The association between multimorbidity and incontinence was mediated by self-reported health (41.2%), medications (26.6%), mobility limitations (20.9%), depressive symptoms (12.8%), disability (11.6%), subjective memory (8.7%) and frailty status (8.3%). This longitudinal study found that physical multimorbidity and specific chronic conditions may increase the risk of new-onset incontinence among Chinese adults aged ≥50years. Self-reported health, medications and mobility limitations seemed to be important intermediate conditions between multimorbidity and incident incontinence.