Input Power Research Articles

Absolute measurement of vacuum ultraviolet fluxes from inductively coupled plasmas via metal surface photoemission currents

Quantifying vacuum-ultraviolet (VUV) fluxes typically requires vacuum-compatible spectrometers and is often associated with significant cost and effort. A simple technique for the absolute measurement of local VUV fluxes from plasmas using the photoemission from a set of coated metal plates, is described. The radiant power from a 13.56 MHz hydrogen plasma operating at 40–87 mTorr and with an radio frequency (RF) input power from 100 to 120 W was investigated by irradiating a set of 2 cm diameter Au, Ag and Cu plates. The variation in photoemission currents was compared with the photoelectric yield curves to estimate the absolute flux incident on the surfaces in the 113–190 nm range. The measured fluxes were found to have an uncertainty of 5%–30% when compared with the VUV spectrometer measurements. The VUV output power was found to have a maximum at a pressure of 70–80 mTorr and to increase with RF power. In all cases, the VUV output power was measured to be approximately 12%–16% of the RF input power to the matching network, in good agreement with spectroscopy results.

Degradation mechanism and decomposition of sulfamethoxazole aqueous solution with persulfate activated by dielectric barrier discharge.

The present study focused on the degradation of sulfamethoxazole (SMX) aqueous solution and the toxicity of processing aqueous by the dielectric barrier discharge (DBD) activated persulfate (PS). The effects of input voltage, input frequency, duty cycle, and PS dosage ratio on the SMX degradation efficiency were measured. Based on the results of the Response Surface Methodology (RSM), SMX degradation efficiency reached 83.21% which is 10.54% higher than that without PS, and the kinetic constant was 0.067 min-1 in 30 min when the input voltage at 204 V (input power at 110.6 W), the input frequency at 186 Hz, the duty cycle at 63%, and the PS dosage ratio at 5.1:1. The addition of PS can produce more active particles reached 1.756 mg/L (O3), 0.118 mg/L (H2O2), 0.154 mmol/L (·OH) in 30 min. Furthermore, the DBD plasma system effectively activated an optimal amount of PS, leading to improved removal efficiency of COD, and TOC to 30.21% and 47.21%, respectively. Subsequently, eight primary by-products were pinpointed, alongside the observation of three distinct pathways of transformation. Predictions from the ECOSAR software indicated that most of the degradation intermediates were less toxic than SMX. The biological toxicity experiments elucidated that the treatment with the DBD/PS system effectively reduced the mortality of zebrafish larvae caused by SMX from 100% to 20.13% and improved the hatching rate from 55.69% to 80.86%. In particular, it is important to note that the degradation intermediates exhibit teratogenic effects on zebrafish larvae.

Theoretical and Experimental Research on Thermal Dynamic Characteristics of Single-Screw Compressor with a New Composite SLIDE valve

Based on the single-screw compressor (SSC) structure, a new type of composite slide valve (CSV) has been proposed and designed, featuring internal volume ratios of 2.8, 3.9, and 5.6 and operating under a partial load of 35%. The theoretical model describing the dynamic features and thermodynamic performance of the SSC with CSV has also been built. The pressure ratio of the experimental system can be adjusted from 3.3 to 7.8, and the experimental results demonstrate the CSV’s effective performance. The deviations between the calculated and measured results for volume ratio and input power are 3.33–9.08% and 0.32–8.03%, and the deviations for heating capacity and adiabatic efficiency range from 0.92–8.73% to 2.09–9.67%, respectively. The introduction of the CSV offers a novel approach to enhancing SSC efficiency. Both the theoretical and experimental findings lay a foundation for future optimization and design improvements in variable load and internal volumetric ratio single-screw compressors.

Design of high‐efficiency rectenna for microwave power wireless transmission systems

AbstractRadio power transmission is studied herein. A rectenna with high‐efficiency microwave power transmission is proposed. Improvement on the traditional Yagi antenna structure is implemented by using a rectenna. In this design, the antenna is fed by a coplanar waveguide, and the impedance bandwidth is widened by adding a set of radiation dipoles. A set of parasitic directors is used to enhance the directionality of the antenna. A rectifier circuit based on a power‐recovery network is designed using an open branch‐line network with harmonic rejection characteristics as a low‐pass filter. The rectifier network topology is adopted with a diode in parallel connection to increase the output voltage of the circuit. The reflected power generated by the impedance mismatch can be recycled by the power‐recovery network. Thus, the rectifying efficiency can be improved. Finally, experimental data show that the radiofrequency–direct current power conversion efficiency of the rectenna can be as high as 77.5% at the operating frequency 2.45 GHz and the input power 12 dBm. The proposed rectenna can be potentially used for the power supply of various wireless sensor nodes with high efficiency.

Properties of the ionization region in a magnetron plasma at gas-aggregation-source-relevant pressure regime explored using a global model

Abstract A global (volume averaged) model is developed for the ionization region of a gas aggregation source (GAS) plasma. The case of using argon gas and a copper target is considered. The model describes the densities of thermal and hot electrons, argon and copper ions, copper atoms and argon atoms in different excited states, the temperature of thermal electrons, the kinetic energies of the ions with which they bombard the target, the sheath width near the target cathode and the energy fluxes by different plasma species to a planar probe in the ionization region. Also, the fraction of input power is estimated which is dissipated to energize the thermal electrons in the ionization region. The gas discharge properties are analysed for different pressures and discharge currents under conditions corresponding to the experimental conditions (Gauter S et al 2018 J. Appl. Phys. 124 073301). The calculated pressure- and current-dependences for the GAS properties are used to explain the measured dependences for the deposition rate and the energy flux. It is found that the deposition rate increases with increasing discharge current because of the growth of currents of copper atoms and ions. With increasing pressure, the rate decreases due to drop of the densities of copper atoms and ions because of decreasing the kinetic energies of the ions with which they bombard the target. The model indicates that in the gas-aggregation-source relevant pressure regime, the energy flux by ions dominates over the energy fluxes of other plasma species.

Femtosecond-laser-inscribed cladding waveguides in KTiOPO4 crystal for second-harmonic generation and Y-branch splitters

In this study, the fabrication of straight- and Y-branch-cladding waveguides in KTiOPO4 crystals using femtosecond laser-direct writing is described. The second-harmonic generation (SHG) of green light through the cladding waveguides was realized using a pulsed-wave pump at 1,064 nm. The guiding properties of straight-cladding waveguides fabricated by varying the laser-writing conditions were investigated. The minimum insertion loss was approximately 2.0 dB at 1,064 nm. Confocal micro-Raman spectroscopy was used to investigate the lattice micro-modifications. The maximum SHG conversion efficiency of the straight-cladding waveguide reached 31.4% with a maximum output power of 79.29 mW from an input power of 252.6 mW. The performances of the Y-branch splitters with splitting angles ranging from 0.5° to 2.6° were characterized at 1,064 nm, showing excellent properties, including symmetrical output ends and approximately equal splitting ratios. An SHG conversion efficiency of 13.4% and maximum output power of 33.63 mW were achieved in the Y-branch splitter with a splitting angle of 1.0°. These findings support potential applications in constructing compact-frequency converters by using femtosecond laser-written KTiOPO4 depressed-cladding waveguides.

Assessment of using different ozone-friendly R22 alternative refrigerants in residential air conditioners in a high-ambient temperature country

The performance of a vapor compression refrigeration system (VCRS)-based residential air conditioner operating in a high-ambient temperature (HAT) country was investigated using six zero-ODP (ozone depletion potential) refrigerants as replacements to R22. The non-flammable alternative refrigerants considered in the present research were R134a, R404A, R407C, R410A, R448A, and R507A. Using the basic conservation laws, the VCRS was modeled during steady-state operation and solved using engineering equation solver (EES) software. Coefficient of performance (COP), pressures and temperatures at compressor suction and discharge, Global Warming Potential (GWP), critical pressure and temperature, compressor pressure ratio, volumetric cooling capacity (VCC) specific cooling capacity (SCC), and refrigeration effect were utilized as assessment criteria for the alternative refrigerants considered. From these refrigerants, the highest values of suction pressure, discharge temperature, and condenser pressure were attained by R410A. In addition, the discharge temperatures for all refrigerants, except R134a, were all higher than their corresponding critical values, causing a quicker drop in the VCRS’s performance. As an alternative refrigerant, R407C showed the highest SCC of 141.0 kJ/kg followed directly by 139.2 and 138.0 kJ/kg for R410A and R448A, respectively. A reverse trend was found for VCC with respective values of 4722 and 3775 kJ/m3 for R410A and R448A. Lower volume flow rates and smaller-sized compressors are expected for higher VCC refrigerants. The same trend was found for the compressor’s specific work input and condenser’s specific heat transfer with values of (51.14, 46.82, and 45.38 kJ/kg) and (190.3, 187.8, and 183.4 kJ/kg) for R410A, R407C, and R448A, respectively. For applications in HAT countries, larger condenser’s specific heat transfer makes the refrigerant more applicable. Conversely, with respect to COP, refrigerant R134a with a value of 3.075 was the superior alternative followed by R448A and R407C with respective COPs of 3.042 and 3.011. Based on the overall assessment in terms of environmental obligation, COP, compressor input power, refrigerant flow rate required, and all the evaluations made in this research, refrigerant R448A was recommended as the most appropriate substitute to R22 which can effectively be used in residential air conditioners in a HAT country.

Thermal defocus-free Hartmann Wavefront Sensors for monitoring aberrations in Advanced Virgo

Earth-based gravitational waves interferometric detectors are shot-noise limited in the high-frequency region of their sensitivity band. While enhancing the laser input power is the natural solution to improve on the shot noise limit, higher power also increases the optical aberration budget due to the laser absorption in the highly reflective coatings of mirrors, resulting in a drop of the sensitivity of the detector. Advanced Virgo exploits Hartmann Wavefront Sensors (HWSs) to locally measure the absorption-induced optical aberrations by monitoring the optical path length change in the core optics. Despite the very high sensitivity of Hartmann sensors, temperature fluctuations can cause a spurious curvature term to appear in the reconstructed wavefront due to the thermal expansion of the Hartmann plate, that could affect the accuracy of the aberration monitoring. We present the implementation and validation of a control loop to stabilize the Advanced Virgo HWS temperature at the order of ΔT⩽0.01 K, keeping the spurious curvature within the detector’s requirements on wavefront sensing accuracy.

A petavoxel fragment of human cerebral cortex reconstructed at nanoscale resolution

To fully understand how the human brain works, knowledge of its structure at high resolution is needed. Presented here is a computationally intensive reconstruction of the ultrastructure of a cubic millimeter of human temporal cortex that was surgically removed to gain access to an underlying epileptic focus. It contains about 57,000 cells, about 230 millimeters of blood vessels, and about 150 million synapses and comprises 1.4 petabytes. Our analysis showed that glia outnumber neurons 2:1, oligodendrocytes were the most common cell, deep layer excitatory neurons could be classified on the basis of dendritic orientation, and among thousands of weak connections to each neuron, there exist rare powerful axonal inputs of up to 50 synapses. Further studies using this resource may bring valuable insights into the mysteries of the human brain.

A Compact GaN Power Amplifier Module for New Generation Cellular Basestations

This paper presents a compact class-AB Power Amplifier Module (PAM) designed for new generation massive Multiple Input Multiple Output (MiMo) cellular base stations. The module is designed at the center frequency of 3.5GHz targeting Long Term Evolution (LTE) and 5G New Radio (NR) bands. The module is a hybrid design that incorporates a Gallium Nitride (GaN) High Mobility-Electron Transistor (HEMT) die, discrete components-based input, and output matching networks. The entire design is realized on a 8.5 x 5.2 mm, 2-layer Rogers4003C substrate. The module is assembled on a PCB as an open-top for post-characterization tuning. The small signal and large signal measurements are in quite good agreement. The measurement results show that the amplifier is unconditionally stable, the input return loss is 12.2 dB, the output return loss is 7.7 dB, and the small signal gain is 13.4 dB. The saturated output power is 33.3 dBm with a Power Added Efficiency of 20.1%. The small signal gain drops to 11.2 dB at around 22 dBm of input power due to GaN technology’s intrinsic soft compression characteristics.

Engineering design and manufacturing of a radio frequency plasma driver without Faraday shield for NBI application

A radio frequency (RF) driven ion source is favorable for high-power and long-pulse neutral beam injection (NBI) system. To reduce the damage caused by the isotropic heat and particle fluxes from the plasma, the traditional RF plasma driver of the NBI ion source introduces a Faraday shield (FS) for protection. However, the simulations and experiments show that the FS seriously affects the RF coupling and around 50 % of the input power deposits on the FS. The water-cooled discharge tubes with a double-layer ceramic structure have been developed to avoid using the FS structure. It's expected to improve the RF power transfer efficiency and to promote the development of high-power and long-pulse RF ion source. To verify the feasibility of the double-layer ceramic structure, the paper has carried out the fluid-thermal-structural coupling analysis and the fracture mechanical analysis on two proposed types: the alumina ceramic brazing structure and the silicon nitride ceramic bonding structure. The sample tests and the prototype manufacturing have been completed. Preliminary tests of the plasma discharge on the prototype of the alumina ceramic brazing structure have been launched. A plasma discharge of 30 kW and 20 s have been achieved.

Development of 2400–2450 MHz Frequency Band RF Energy Harvesting System for Low-Power Device Operation

Recently, there has been an increasing fascination for employing radio frequency (RF) energy harvesting techniques to energize various low-power devices by harnessing the ambient RF energy in the surroundings. This work outlines a novel advancement in RF energy harvesting (RFEH) technology, intending to power portable gadgets with minimal operating power demands. A high-gain receiver microstrip patch antenna was designed and tested to capture ambient RF residue, operating at 2450 MHz. Similarly, a two-stage Dickson voltage booster was developed and employed with the RFEH to transform the received RF signals into useful DC voltage signals. Additionally, an LC series circuit was utilized to ensure impedance matching between the antenna and rectifier, facilitating the extraction of maximum power from the developed prototype. The findings indicate that the developed rectifier attained a peak power conversion efficiency (PCE) of 64% when operating at an input power level of 0 dBm. During experimentation, the voltage booster demonstrated its capability to rectify a minimum input AC signal of only 50 mV, yielding a corresponding 180 mV output DC signal. Moreover, the maximum power of 4.60 µW was achieved when subjected to an input AC signal of 1500 mV with a load resistance of 470 kΩ. Finally, the devised RFEH was also tested in an open environment, receiving signals from Wi-Fi modems positioned at varying distances for evaluation.

Experimental and Numerical Investigation of Single-Phase Liquid Cooling for Heterogeneous Integration Multi-Chip Module

Abstract The variety of new electronic packaging technologies has grown significantly over the last 20 years as a result of market demands for higher device performance at lower costs and in less space. Those demands have pushed for heterogeneous packaging, where computer chips with different stack heights are closely packed, creating non-uniform heat flux and temperature and with poor thermal management it will escalate thermal stresses on the chip, and potential reliability issues. To mimic this real-life scenario packaging, an experimental setup was designed and built. The design of the new experimental setup consists of four identical 1.2 cm × 1.2 cm ceramic heaters, each of which is connected to a separate power supply and can reach a heat flux of 140 W/cm2. Accordingly, this mock package is capable of delivering different power levels to mimic different multicore microprocessor conditions. To give the heater the ability to move precisely in the x, y, and z directions, each heater is mounted to an XYZ linear stage. Deionized water was used as the working fluid, and a pin-fin heat sink was used to run the initial steady-state tests on the experimental rig. The tests showed how different flow rates at constant fluid temperature and input power affect the temperatures of the heaters and the thermohydraulic performance of the heat sink. In addition, a three-dimensional numerical model has been developed and validated with experimental data in terms of heat sink pressure drop and temperatures of the heaters.

Empirical Investigation of a Single-phase Input Switched AC-DC Boost Converter with Improved Power Quality

The Boost converter topology is most widely used for power factor correction (PFC) converters. The conventional passive Boost PFC converter inherently suffers from the lack of controllability and non-ideal characteristics of the diode-bridge rectifier. Replacing diodes with active switch(es) offers viable solutions but increases the circuit complexity. Addressing this trade-off, a novel design of a single–phase input switched AC to DC Boost converter has been presented in this article. The active switch of the Boost DC converter is shifted to the input side of the full-bridge diode rectifier which provides more control on the input current without increasing much of the circuit complexity. Two Boost inductors and two output split capacitors are used for providing higher step-up operation compared to the conventional. The converter has been simulated both in open-loop and closed-loop conditions using the PSIM software. The simulation results show that the proposed converter provides good dynamic response and can maintain a constant stable output voltage during sudden load change. Furthermore, to evaluate the experimental performance of the suggested converter, a prototype converter has been developed. A scaled-down experiment has been performed which shows that the converter can achieve up to 85.2 % efficiency and an input power factor of 0.9.

Design and Fabrication of a Film Bulk Acoustic Wave Filter for 3.0 GHz-3.2 GHz S-Band.

Film bulk acoustic-wave resonators (FBARs) are widely utilized in the field of radio frequency (RF) filters due to their excellent performance, such as high operation frequency and high quality. In this paper, we present the design, fabrication, and characterization of an FBAR filter for the 3.0 GHz-3.2 GHz S-band. Using a scandium-doped aluminum nitride (Sc0.2Al0.8N) film, the filter is designed through a combined acoustic-electromagnetic simulation method, and the FBAR and filter are fabricated using an eight-step lithographic process. The measured FBAR presents an effective electromechanical coupling coefficient (keff2) value up to 13.3%, and the measured filter demonstrates a -3 dB bandwidth of 115 MHz (from 3.013 GHz to 3.128 GHz), a low insertion loss of -2.4 dB, and good out-of-band rejection of -30 dB. The measured 1 dB compression point of the fabricated filter is 30.5 dBm, and the first series resonator burns out first as the input power increases. This work paves the way for research on high-power RF filters in mobile communication.

Computational study of a helium-propellant microwave electrothermal thruster

The microwave electrothermal thruster (MET) utilizes wave-exited microdischarges to heat gas flows, enhancing the specific impulse of the thruster. Our computational study investigates a 17.5 GHz helium-propellant MET, employing a two-dimensional, axisymmetric fluid model of plasma coupled with electromagnetic wave and gas flows. The discharges operate in the glow regime, remaining weakly ionized, and in thermal non-equilibrium. The plasma densities reach approximately 1020m−3, and the gas temperature is around 2000 K. Even a slight off-resonant frequency operation results in a significantly lower plasma density and gas temperature. Gas heating, primarily driven by electromagnetic Joule heating, plays a critical role in influencing the overall discharge behavior. The measured peak thrust and specific impulse are 8.24 mN and 292 s, respectively, at a mass flow rate of 3.2 mg/s with 30 W of power. Compared to a cold gas thruster, there is a significant increase in the specific impulse by a factor of approximately 1.7. The enhanced performance trades off with propulsive efficiency, which decreases by a factor of 1.5 from the peak 65% at 10 W. This is due to higher energy losses to cavity walls from heat conduction with increased power. These findings underscore the critical balance between the input power and mass flow rate to improve the MET performance, highlighting the importance of power management to maximize thrust and efficiency. Furthermore, the predicted thrust and specific impulse agree well with experimental values for nominally similar MET thruster studies in the literature.

Design and optimization of a miniaturized dual band rectenna for wireless power transfer applications

This paper presents the design of a compact printed rectenna circuit suitable for wireless power transfer applications at frequencies 900 MHz and 1450 MHz. The rectenna circuit consists of a rectangular patch antenna measuring 17.7 x 8.85 mm2, printed on a Rogers RO4003 substrate. It also includes a voltage doubler (VD) circuit comprising Schottky diodes (SMS7631) and an impedance-matching circuit. The design and optimization of the antenna are performed using Ansys HFSS software, while the DC and RF features of the VD circuit are analyzed using the Advanced Design System (ADS) software. The circuit design is presented in two stages: one for single-frequency operation at 900 MHz and another for dual-band operation at 900 and 1450 MHz. The design of single-stage and double-stage VD for dual-band operation is also discussed in this paper. The rectenna's Power Conversion Efficiency (PCE) is evaluated under various load and input power conditions. The maximum DC output voltage measured is 5.318 V at 900 MHz and 5.52 V at 1450 MHz. Furthermore, the maximum PCE achieved is 53% and 54% for 900 MHz and 1450 MHz respectively. These values are obtained with a RF input power level of 20 dBm and a load resistance of 10 KΩ.

Modulation instability in nonidentical metamaterial waveguide arrays by graph Laplacian approach

We theoretically investigate modulation instability (MI) in a nonidentical waveguide array, which is made up of positive and negative index metamaterial waveguides. The unit cell of the optical waveguide array consists of three waveguides arranged in a triangular manner. Waveguides 1 and 3 are made up of positive index material (PIM) channels and waveguide 2 is by negative index material (NIM) channels, as a result, they show different light propagation characteristics. We model this array of waveguides using a generalized nonlinear Schro¨dinger equation, replacing the Laplacian operator with the graph Laplacian. Following linear stability analysis, we will discuss MI for different values of transverse wave number, as it determines the order of the Brillouin zone. We also discuss the effect of input power on periodic MI in normal and anomalous dispersion regimes. Thus we report a comprehensive study on the MI and hence the better ways to generate and manipulate the solitons or ultra-short pulses in NIM PIM waveguide arrays.

128-channel optical phased array with large field of view and low main-lobe attenuation

In this paper, a 128-channel non-uniform optical phased array is proposed. The antenna is based on a silicon nitride waveguide with a large cross-sectional area (3 μm × 1.2 μm) and a silicon nitride grating with a small diffraction window (grating width of 200 nm), enabling high optical power transmission and a wide 1 dB field of view. As a result, the designed sparse optical phased array achieves less than 1 dB of main lobe attenuation over a 94° field of view. Within this field of view, the main lobe will not fall below 80% of the maximum main lobe. This allows the minimum detection distance to still be about 89% of the maximum detection distance without increasing the input power. In this field of view, the maximum side-lobe suppression of the designed sparse optical phased array is 13.4 dB, and the minimum side-lobe suppression is higher than 11.9 dB. This is useful for simultaneously achieving a large field of view, low main lobe attenuation, stable side-lobe suppression, and long detection distance.

Analysis, Design and Effectuation of a Tapped Inductor Current Converter with Fractional Output for Current Source Systems

This article proposes a new connection method of tapped inductors that works in the current source, which enables the current-mode power converter circuit to have a new topological relationship. Usually, in a switched-inductor circuit, a stable output multiple is obtained through the connection of the inductor and the switching devices. This is because the tapped point on the inductor varies, and the magnetomotive force (mmf) of inductance is adjusted. Thereby, the output current is controlled by the states of switching devices within a certain range. This optimized circuit structure can adjust the output current according to load changes in practical applications without changing the input power supply. The proposed method has been verified for its feasibility through detailed analysis and hardware work. The principal analysis based on the flux linkage and the PSIM simulation confirms that the theoretical circuit can be implemented. Finally, a hardware circuit is built to obtain real and feasible conclusions, and it is verified that the circuit can achieve a stable output and variable current within a specific range. The proposed work presents an alternative power conversion methodology using the active switching of mmf, and it is a stable and simple power conversion technique.