Injection Of Large Sample Volumes Research Articles

Micro liquid–liquid extraction combined with large-volume injection gas chromatography–mass spectrometry for the determination of haloacetaldehydes in treated water

Haloacetaldehydes (HAs) are becoming the most widespread disinfection by-products (DBPs) found in drinking water, besides trihalomethanes and haloacetic acids, generated by the interaction of chemical disinfectants with organic matter naturally present in water. Because of their high potential toxicity, HAs have currently received a singular attention, especially trichloroacetaldehyde (chloral hydrate, CH), the most common and abundant compound found in treated water. The aims of this study are focused on the miniaturisation of EPA Method 551.1, including some innovations such as the use of ethyl acetate as the extracting solvent, the enhancement of HAs stability in aqueous solutions by adjusting the pH ∼3.2 and the use of a large-volume sample injection (30 μL) coupled to programmed temperature vaporizer–gas chromatography–mass spectrometry to improve both sensitivity and selectivity. In optimised experimental conditions, the limits of detection for the 7 HAs studied ranged from 6 to 20 ng/L. Swimming pools have recently been recognized as an important source of exposure to DBPs and as a result, in this research for the first time, HAs have been determined in this type of water. Two HAs have been found in the analysed water: CH at concentrations between 1.2–38 and 53–340 μg/L and dichloroacetaldehyde between 0.07–4.0 and 1.8–23 μg/L in tap and swimming pool waters, respectively.

Large-Volume Injection of Sample Diluents not Miscible with the Mobile Phase as an Alternative Approach in Sample Preparation for Bioanalysis: An Application for Fenspiride Bioequivalence

Liquid-liquid extraction of target compounds from biological matrices followed by the injection of a large volume from the organic layer into the chromatographic column operated under reversed-phase (RP) conditions would successfully combine the selectivity and the straightforward character of the procedure in order to enhance sensitivity, compared with the usual approach of involving solvent evaporation and residue re-dissolution. Large-volume injection of samples in diluents that are not miscible with the mobile phase was recently introduced in chromatographic practice. The risk of random errors produced during the manipulation of samples is also substantially reduced. A bioanalytical method designed for the bioequivalence of fenspiride containing pharmaceutical formulations was based on a sample preparation procedure involving extraction of the target analyte and the internal standard (trimetazidine) from alkalinized plasma samples in 1-octanol. A volume of 75 µl from the octanol layer was directly injected on a Zorbax SB C18 Rapid Resolution, 50 mm length × 4.6 mm internal diameter × 1.8 µm particle size column, with the RP separation being carried out under gradient elution conditions. Detection was made through positive ESI and MS/MS. Aspects related to method development and validation are discussed. The bioanalytical method was successfully applied to assess bioequivalence of a modified release pharmaceutical formulation containing 80 mg fenspiride hydrochloride during two different studies carried out as single-dose administration under fasting and fed conditions (four arms), and multiple doses administration, respectively. The quality attributes assigned to the bioanalytical method, as resulting from its application to the bioequivalence studies, are highlighted and fully demonstrate that sample preparation based on large-volume injection of immiscible diluents has an increased potential for application in bioanalysis.

On the minimization of the band-broadening contributions of a modern, very high pressure liquid chromatograph

Abstract The contributions of the volume of sample injected, the mobile phase flow rate, the inner diameter of the needle seat capillary and that of the connector capillary, the heat exchanger, and the detector cell volume to the widths of bands eluted from the 1290 Infinity HPLC instrument were investigated in depth. Four sample volumes (0.16, 0.80, 4.0, and 20 μL), three flow rates (0.04, 0.4, and 4.0 mL/min), two needle seat capillary I.D. (100 mm × 115 and 140 μm), three sets of connector capillary I.D. (350 mm × 80, 115, and 140 μm placed upstream the column, and 220 mm × 80, 115, and 140 μm downstream the column), two UV detector cell volumes (0.8 and 2.4 μL), and the presence/absence of the heat exchanger (1.6 μL) between the inlet connector capillary tube and the column were combined to generate up to 4 × 3 × 2 × 3 × 2 × 2 = 288 system configurations for this instrument. For each configuration, 5 consecutive injections were performed in order to assess the injection-to-injection repeatability, providing 1440 elution band profiles which are analyzed. The results demonstrate that the band broadening contribution of the instrument depends mostly on the detector cell volume and on the inner diameter of the needle seat capillary tube. The impact of these two contributions is particularly important at high flow rates (4 mL/min). Best efficiencies are obtained with a small sample volume, below 1 μL, which avoids volume overload of the instrument, or with large sample volumes, which maximize the radial concentration gradients of the sample across the instrument channels, in the vicinity of the anfractuosities of the channel walls. The injection of large sample volumes reveals the imperfection of current injection systems, the performance of which is remote from the one expected to provide an ideal rectangular injection (∼+4 μL 2). Although the present behavior of the instrument is satisfactory, serious improvements would become necessary to operate the next generation of more efficient columns that might be commercialized soon.

High sensitive analysis of steroids in doping control using gas chromatography/time‐of‐flight mass‐spectrometry

The method of high sensitive gas chromatographic/time-of-flight mass-spectrometric (GC/TOF-MS) analysis of steroids was developed. Low-resolution TOF-MS instrument (with fast spectral acquisition rate) was used. This method is based on the formation of the silyl derivatives of steroids; exchange of the reagent mixture (pyridine and N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA)) for tert-butylmethylether; offline large sample volume injection of this solution based on sorption concentration of the respective derivatives from the vapour-gas mixture flow formed from the solution and inert gas flows; and entire analytes solvent-free concentrate transfer into the injector of the gas chromatograph. Detection limits for 100 µl sample solution volume were 0.5-2 pg/µl (depending on the component). Application of TOF-MS model 'TruTOF' (Leco, St Joseph, MO, USA) coupled with gas chromatograph and ChromaTOF software (Leco, St Joseph, MO, USA) allowed extraction of the full mass spectra and resolving coeluted peaks. Due to use of the proposed method (10 µl sample aliquot) and GC/TOF-MS, two times more steroid-like compounds were registered in the urine extract in comparison with the injection of 1 µl of the same sample solution.

Large volume injection of 1-octanol as sample diluent in reversed phase liquid chromatography: Application in bioanalysis for assaying of indapamide in whole blood

Large volume injection of samples in strong diluents immiscible with the mobile phases used in reversed phase liquid chromatography (RPLC) has been recently introduced in practice. In the present work, the potential of the technique has been evaluated for bioanalytical applications. The process consists of the liquid–liquid extraction of indapamide from whole blood into 1-octanol, followed by the direct injection from the organic layer into the LC. Detection was made through negative electrospray ionization (ESI) and tandem mass spectrometry (MS 2). The method was developed, validated, and successfully applied to a large number of samples in two bioequivalence studies designed for indapamide 1.5 mg sustained release and 2.5 mg immediate release pharmaceutical formulations. The performance of the analytical method is discussed based on data resulting from the validation procedure and the completion of the bioequivalence studies.

Automated sample treatment with the injection of large sample volumes for the determination of contaminants and metabolites in urine

This work reports the development of a simple and automated method for the quantitative determination of several contaminants (triazine, phenylurea, and phenoxyacid herbicides; carbamate insecticides and industrial chemicals) and their metabolites in human urine with a simplified sample treatment. The method is based on the online coupling of an extraction column with RP LC separation-UV detection; this coupling enabled fast online cleanup of the urine samples, efficiently eliminating matrix components and providing appropriate selectivity for the determination of such compounds. The variables affecting the automated method were optimized: sorbent type, washing solvent and time, and the sample volume injected. The optimized sample treatment reported here allowed the direct injection of large volumes of urine (1500 microL) into the online system as a way to improve the sensitivity of the method; limits of detection in the 1-10 ng/mL range were achieved for an injected volume of 1500 microL of urine, precision being 10% or better at a concentration level of 20 ng/mL. The online configuration proposed has advantages such as automation (all the steps involved in the analysis - injection of the urine, sample cleanup, analyte enrichment, separation and detection - are carried out automatically) with high precision and sensitivity, reducing manual sample manipulation to freezing and sample filtration.

Determination of melamine in milk powder using zwitterionic HILIC stationary phase with UV detection

A hydrophilic interaction liquid chromatography-UV method was developed for the determination of melamine in milk powder. Sulfobetaine type zwitterionic hydrophilic interaction liquid chromatography stationary phase was used to achieve straightforward separation of melamine in milk powder without any sample derivatization or addition of ion-pair reagent. The sample preparation was simple and fast with the steps of acetonitrile/perchloric acid extraction-centrifugation-filtration. No SPE or other pre-concentration procedure was required. By using large volume sample injection and choosing low UV wavelength (210 nm), the LOD and LOQ were 0.005 and 0.015 microg/mL for melamine standards, and 0.02 and 0.06 microg/mL for the spiked milk extracts. The LOD and LOQ of the latter correspond to 0.95 and 2.2 microg/g melamine in the milk powder. The correlation coefficients for melamine standard, pre-spiked milk extracts and post-spiked milk extracts in the range of 0-0.5 microg/mL were 0.9978, 0.9976 and 0.9995, respectively. This newly developed method is sensitive and cost effective, therefore, suitable for screening of melamine in tainted milk products.

Reversed phase liquid chromatography trace analysis of pesticides in soil by on‐column sample pumping large volume injection and UV detection

The idea of utilization of one hydraulic line of a common commercial HPLC pump for direct on-column sample pumping injection of large sample volumes, 20 mL, was further investigated with the aim to develop multicomponent pesticides trace residues HPLC method in gram soil samples. Target pesticides group involve asulam, atrazine, 2,4-D, PCA, propazine, simazine, 4-chloro-2-methylphenoxyacetic acid, 2-(4-chloro-2-tolyloxy) propionic acid, chlortoluron, metoxuron, epoxiconazole. The results proved the applicability of this approach in experiments with mixtures of analytes at low ng/mL levels. Analysis of 20 mL of soil leachates and extracts of fortified soil samples containing these pesticides at the 10-50 ng/g level (in dry soil) revealed good figures of merit, also in the presence of large excess of humics. LODs achieved by detection at 220 nm evaluated from calibration runs of spiked soil extracts by Hubaux et al. method ranged from 5-12 ng per injected volume. For 20 mL large volume injection it represents 0.25-0.6 ng/mL of diluted soil extract, or 2.5-6 ng/mL of crude extract, or 6-5 ng/g dry soil. Recoveries of pesticides at concentration levels approaching half of maximum allowable concentration of pesticides in soil (100 ng/g) ranged from 85 to 98% with acceptable reproducibility, except asulam and metoxuron.

Determination of estrogens and bisphenol A in bovine milk by automated on-line C 30 solid-phase extraction coupled with high-performance liquid chromatography–mass spectrometry

Using triacontyl bonded silica (C 30) as on-line solid-phase extraction (SPE) material and a specially designed on-line analytical system which allowed large sample volume injection, a high speed and robust on-line SPE-HPLC–MS method was established for the analysis of five estrogens and bisphenol A (BPA) in milk samples. The milk sample is pretreated with acetonitrile for protein precipitation and then treated with primary secondary amine for the removal of polar impurities in the matrix. Then the pretreated sample can be automatically loaded by a LC pump. For effective extraction, an offshoot with NH 4Ac solution of high-flow rate was employed to dilute the loaded sample by a mixing tee before sample was loaded onto the C 30 extraction column. In this way, large volume injection (1 mL in this experiment) could be achieved. Some important parameters such as sample loading flow rate, sample dilution ratio and injection volume were optimized. Under the optimized conditions, the recoveries for all analytes range from 71.4 to 97.1% and reproducibility represented as RSDs are less than 15.0% ( n = 5) with milk samples spiked at 0.6 and 15 ng/mL of each analyte. To the authors’ knowledge, it constitutes the first work describing a C 30 on-line SPE-LC–MS analytical method for the screen and monitoring of these estrogens and BPA in milk.

Electro membrane isolation of nerve agent degradation products across a supported liquid membrane followed by capillary electrophoresis with contactless conductivity detection

In the present study, electro membrane isolation (EMI) of four nerve agent degradation products has been successfully explored. In the procedure, a polypropylene sheet membrane folded into an envelope with an open end with its wall pores impregnated with 1-octanol was employed as the artificial supported liquid membrane (SLM). The envelope containing the extractant or aqueous acceptor phase (at pH 6.8) was immersed in the sample or donor phase (also aqueous at a pH of 6.8) for extraction. This ensured that the target analytes were fully ionized. A voltage was then applied, with the negative electrode placed in the donor phase with agitation, and the positive electrode in the acceptor phase. The ionized analytes were thus driven to migrate from the donor phase across the SLM to the acceptor phase. The factors influential to extraction: type of organic solvent, voltage, agitation speed, extraction time, pH of the donor and acceptor phase and concentration of humic acids were investigated in detail. After extraction, the acceptor phase was collected and directly injected for capillary electrophoretic (CE) analysis. Combined with capacitively coupled contactless conductivity detection (C 4D), the direct detection of these compounds could be achieved. Moreover, large-volume sample injection was employed to further enhance the sensitivity of this method. Limits of detection (LODs) as low as ng/mL were reached for the studied analytes, with overall LOD enhancements of four orders of magnitude.

Ion-pair liquid–liquid–liquid microextraction of nerve agent degradation products followed by capillary electrophoresis with contactless conductivity detection

The four nerve agent degradation products methylphosphonic acid (MPA), ethyl methylphosphonic acid (EMPA), isopropyl methylphosphonic acid (IMPA) and cyclohexyl methylphosphonic acid (CMPA) have been successfully extracted from aqueous sample solution by ion-pair liquid–liquid–liquid microextraction. In this procedure, the target analytes in the sample solution were converted into their ion-pair complexes with tri- n-butyl amine and then extracted by an organic solvent (1-octanol) layer on top of the sample solution. Simultaneously, the analytes were back-extracted into a drop of an aqueous acceptor solution which was suspended in the organic phase at a microsyringe needle tip. The factors influential to extraction: type of organic solvent, type of ion-pair reagent and its concentration, pH values of sample solution and acceptor aqueous phase, stirring rate and extraction time were investigated in detail. After extraction, the drop of the acceptor solution was withdrawn into the syringe and injected into a capillary electrophoresis system for analysis. Using contactless conductivity detection, direct quantification of these compounds is possible. Moreover, large-volume sample injection was employed for further preconcentration. Improvements in the limits of detection between 2.5 and 4 orders of magnitude could be achieved and concentrations at the ng/mL level can be determined. This newly established approach was successfully applied to a spiked river water sample.

Increased Throughput and Reduced Carryover of Mass Spectrometry-Based Proteomics Using a High-Efficiency Nonsplit Nanoflow Parallel Dual-Column Capillary HPLC System

We report a new design of a fully automated, high-efficiency parallel nonsplit nanoflow capillary HPLC system, coupled on-line with linear ion trap (LTQ) and high performance nanoelectrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (nanoESI LTQ-FTICR MS). The system, intended for high-throughput proteome analysis of complex protein mixtures, notably serum and plasma, consists of two reversed-phase trap columns for large volume sample injection with high speed sample loading and desalting and two reversed-phase analytical capillary columns. Through a nanoscale two-position, 10-port switching valve, the whole system is terminated by a 10 microm i.d. of nanoemitter mounted on the nanoelectrospray source in front of the sampling cone of the LTQ-FTICR MS. Gradient elution to both nanoflow-rate capillary columns is simultaneously delivered by a single HPLC system via two independent binary gradient pump systems. The parallel capillary column approach eliminates the time delays for column regeneration/equilibration since one capillary column is used for separating the sample mixtures and delivering the separated fractions to the MS, while the other capillary column is being regenerated and equilibrated. The reproducibility of retention time and peak intensity of the present automated parallel nanoflow-rate capillary HPLC system is comparable to that obtained using a single column configuration. Replicate injections of tryptic digests indicated that this system provided good reproducibility of retention time and peak area on both columns with average CV values of less than 1.08% and 7.04%, respectively. Throughput was increased to 100% for 2-h LC-MS analysis compared to the single capillary column LC-MS pipeline. Application of this system is demonstrated in a plasma proteomic study. A total of 312 868 MSMS events were acquired and 1564 proteins identified with high confidence (Protein Prophet > or = 0.9, and peptides matched > or = 2). Comparison of a series of plasma fractions run using the single-column LC-MS versus the parallel-column LC-MS demonstrated that parallel-column LC-MS system significantly reduced the sample carryover, improved MS data quality and increased the number of MS/MS sequence scan events.

Solid-phase microextraction and sample stacking micellar electrokinetic chromatography for the analysis of pesticide residues in red wines

Solid-phase microextraction (SPME) in combination with sample stacking micellar electrokinetic chromatography (MEKC) was studied for the simultaneous determination of 11 multi-class pesticides residues (pirimicarb, metalaxyl, pyrimethanil, procymidone, nuarimol, azoxystrobin, tebufenozide, fenarimol, benalaxyl, penconazole and tetradifon) in red wines samples. Pesticide residues present in the samples were preconcentrated by SPME using poly(dimethylsiloxane)/divinylbenzene (PDMS/DVB) fibers and the injection of large sample volumes into the capillary by reversed-electrode polarity stacking mode (REPSM). Validation of the method was carried out. The combination of both preconcentration procedures (SPME and REPSM) allowed the determination of 10 of these pesticides in red wines at concentrations between 0.049 and 1.69 mg/L ( i.e., levels well below the maximum residue limits (MRLs) allowed for these compounds in wine grapes, except for pirimicarb). Repeatability and accuracy of the SPME-MEKC-DAD method was verified by five consecutive extractions of spiked red wine samples at three levels of concentration. Apparent recovery values were in the range 90–107%. The potential of the method was demonstrated by analyzing multiple homemade red wine samples from the Canary Islands and two commercial samples. Only pyrimethanil, procymidone and azoxystrobin were found in the homemade samples; among them, the pesticide most frequently detected was procymidone.

2D LC Separation and Determination of Bradykinin in Rat Muscle Tissue Dialysate with On-Line SPE-HILIC-SPE-RP-MS

A 2D liquid chromatography (LC) system using hydrophilic interaction chromatography (HILIC) and reversed phase columns has been employed for comprehensive (LC × LC) separation of rat muscle tissue micro-dialysate. Incorporation of an on-line reverse-phase solid phase extraction (SPE) enrichment column in front of the first dimension enabled aqueous samples with high salt concentrations to be injected directly without compromising the chromatographic performance of the HILIC column. Since the SPE enrichment column allowed injection of large sample volumes (e.g. 450 μL), a capillary HILIC column (inner diameter 0.3 mm) could be employed instead of a larger column which is often used in the first dimension to load sufficient amounts of sample. The two chromatographic dimensions were connected using a column selector system with 18, 1.0 mm I.D. C18 “transition” SPE columns. A PLRP C18 column was used in the second dimension. The 2D LC system’s performance was evaluated with a tryptic digest mixture of three model proteins. Good trapping accuracy (HILIC→transition SPE→RP recovery >95%) and repeatability (within-and between day retention time RSDs of first and second dimension chromatography >1%) was achieved. A dialysis sample of rat muscle tissue was separated with the 2D system, revealing complexity and large differences in concentrations of the various compounds present, factors which could potentially interfere with the quantification and monitoring of two target analytes, arg-bradykinin and bradykinin. Subsequently, “Heart-cut” 2D LC-electrospray–mass spectrometry (ESI–MS) with post-column on-line standard injection was employed to monitor arg-bradykinin and bradykinin levels as a function of various muscle conditions. The method’s quantification precision was RSD = 3.4% for bradykinin.

空気中真菌類の分子マーカーとしてのエルゴステロールの大量注入ＧＣ／ＭＳ分析

空気中真菌類の分子マーカーとしてのエルゴステロールの大量注入ＧＣ／ＭＳ分析

Identification of three novel compounds in wine by means of a laboratory-constructed multidimensional gas chromatographic system

A laboratory-made off-line multidimensional GC–GC system has been optimized and applied to the isolation and identification of three novel aroma compounds in wine. The system comprises two independent chromatographs equipped with four-port manually actuated valves and fast capillary connectors that make it possible to quickly transfer a capillary trapping loop from the first to the second system. The first system includes a split/splitless injector, a thick phase semi-capillary column, the valve and both a flame ionization detection (FID) system and a sniffing port. The trapping loop lies outside the chromatograph and it is immersed in a Dewar with liquid nitrogen. The second system includes a programmable temperature vaporization (PTV) injector, the valve, the analytical column and two parallel detectors (a MS system and a sniffing port). The injection of large sample volumes (90 μl) in the first GC system and the general operation of the system have been optimized. The extract was obtained by purging the wine at 37 °C with a stream of nitrogen and trapping the volatiles in a bed containing 1 g LiChrolut EN. Fatty acids and alcohols were removed by washing the resins with a water/methanol solution containing 1% NaHCO 3, and volatiles were recovered with dichloromethane. The GC–MS analysis of the cuts obtained in the first GC system made it possible to identify by first time in wine the strong smelling compounds ethyl 2-, 3- and 4-methylpentanoate.

Large-Volume Sample Sweeping with a High Theoretical Plate Number Using a Coupled-Capillary in Capillary Electrophoresis

A large-volume sample injection (> 5 microL) with an extremely high theoretical plate number (N > 10(7)) was achieved when the sweeping-MEKC mode and a coupled-capillary (100 - 50 microm i.d.) were simultaneously used in a capillary electrophoresis (CE) separation. A low-cost and compact violet-LED ( approximately 2 mW) was used as the fluorescence excitation source. As a result, the theoretical plate numbers of the detected peaks (two model compounds: naphthalene-2,3-dicarboxaldehyde derivatized-dopamine and -norepinephrine) were 1.0 x 10(7) and 7.4 x 10(6), respectively. The limits of detection (at S/N = 3) of these were determined to be 2.8 x 10(-10) M (92 ppt) and 2.3 x 10(-10) M (83 ppt), respectively.

Dynamic pH junction-sweeping capillary electrophoresis for online preconcentration of toxic pyrrolizidine alkaloids in Chinese herbal medicine

There is a need to develop simple yet effective preconcentration methods to enhance concentration sensitivity for CE analysis of trace level analytes in real samples, particularly when commonly available but less sensitive detection methods, e.g., UV detection, are used. In this report, a hyphenated online preconcentration strategy combining dynamic pH junction with sweeping (i.e., dynamic pH junction-sweeping) was employed for the analysis of four toxic pyrrolizidine alkaloids (PAs) of senkirkine, senecionine, retrorsine, and seneciphylline in Chinese herbal medicine (Kuan donghua). Direct electrokinetically focusing of a large sample volume injection (up to 20% of capillary length) on the capillary was performed using the dynamic pH junction-sweeping method. A sample matrix consisting of 10 mM phosphate with 20% methanol at pH 4.0 and a BGE containing 20 mM borate, 30 mM SDS, and 20% methanol at pH 9.1 were utilized to realize dynamic pH junction-sweeping for PAs. This online preconcentration strategy resulted in sensitivity enhancement factors ranging from 23.8- to 90.0-fold for the four toxic PAs, giving an LOD as low as 30 ppb for the PAs. Critical factors such as sample matrix type, pH, and salt concentration were also examined to achieve higher sensitivity enhancement, shorter analysis time, and better resolution. The results indicate that the proposed dynamic pH junction-sweeping technique is a powerful alternative approach for identification and determination of trace levels of these toxic PAs and other hydrophobic, protonatable compounds in real samples.

On-line preconcentration for capillary electrophoresis-atomic fluorescence spectrometric determination of arsenic compounds.

An on-line preconcentration method was developed for capillary electrophoresis (CE) with hydride generation-atomic fluorescence spectrometric (HG-AFS) detection of arsenite, arsenate, dimethylarsenic acid, and monomethylarsenic acid. These arsenic species were negatively charged in the sample solution with high pH. When the potential was applied to the electrophoretic capillary, the negatively charged analyte ions moved faster and stacked at the boundary of sample and CE buffer with low pH. So, high sample pH in combination with low buffer pH allowed the injection of large sample volumes (approximately 1100 nL). Comparison of the preconcentration of analyte solution, prepared with doubly deionized water and that prepared with lake or river water, indicated that preconcentration was independent on the original matrix. With injection of approximately 1100 nL sample, an enrichment factor of 37-50-fold was achieved for the four species. Detection limits for the four arsenic species ranged from 5.0 to 9.3 microg.L(-1). Precisions (RSDs, n = 5) were in the range of 4.9-6.7% for migration time, 4.7-11% for peak area, and 4.3-7.1% for peak height, respectively. The recoveries of the four species in locally collected water solution spiked with 0.1 microg.mL(-1) (as As) ranged from 83 to 109%.

Analysis of microsomal metabolic stability using high-flow-rate extraction coupled to capillary liquid chromatography–mass spectrometry

A method is described for on-line high-speed extraction of microsomal samples and analysis by capillary liquid chromatography–mass spectrometry (LC–MS) for the determination of metabolic stability in connection with the development of positron emission tomography (PET) tracers. The method allowed direct injections of large sample volumes at a fast extraction rate, providing a gain in both sensitivity and sample preparation time. The calibration curve of the test compound flumazenil (Ro 15–1788) was linear in the concentration range of 1–150 nM, with a correlation coefficient exceeding 0.999. The accuracy of the method ranged from 98 to 101%. A high precision was obtained, with mean intra-assay and inter-assay relative standard deviations of at most 1.4 and 1.5%, respectively, for quality control (QC) samples. The extraction efficiency was determined to be 99.4%, the total recovery 96% and the carryover to ≤0.23%. Extractions were performed in a concentration interval of 30–3000 nM without any sign of column overload. The method was successfully used for determining the microsomal metabolic stability of flumazenil. As a result, the described analysis system is currently used for metabolic screening of PET tracer candidates in our laboratory.