Infrared LED Research Articles

Pattern-based Remote Switch for Domestic and Technological Operations

Abstract: This research explores the development of a remote-control system for domestic appliances using user-drawn patterns on a grid, aiming to provide an intuitive and accessible control method. The system is designed around a 3x3 grid of infrared (IR) LEDs and receivers that detect patterns drawn by the user with a finger or stylus. Each grid coordinate is mapped to a specific action, such as turning lights on or off or adjusting the speed of a fan. The detected patterns are transmitted to a NodeMCU ESP8266 microcontroller, which decodes the patterns and activates the corresponding appliance through Wi-Fi commands and relays. The innovative aspects of this system include its simple and intuitive interaction method, allowing users to define custom patterns for various actions, which enhances personalized control. The pattern-based interaction is particularly beneficial for individuals with limited dexterity or mobility, offering an accessible alternative to traditional remote controls. This project demonstrates the potential of combining hardware components, such as IR LEDs and receivers, with embedded C programming to create a user-friendly and efficient home automation solution. The proposed system not only simplifies the user experience but also provides a flexible and customizable interface for controlling domestic appliances.

High-reflectivity composite metal substrate for high-power IRLED

Substrate transfer technology is a common way to prepare high-power infrared light emitting diode (IRLED), which seriously affects the photoelectric performance and reliability of LED. In this paper, a preparation technology of LED with composite metal substrate is presented. Based on electroplating and electron beam evaporation, AuGeNi/Au(1)/Au(2)/Cu composite metal substrate with thickness of 70 nm/30 nm/100 nm/45 μm was prepared, and low resistivity of 4.65 × 10−6 Ω⋅cm2 and high reflectance of 91.3 % were obtained. Compared with the original GaAs substrate, the light output power (LOP) of electroluminescence is increased by 89.2 % at the current of 300 mA.

Frequency Reconfigurable Antenna Design and Analysis with White LED Lamp, Red and Infra-red LEDs

Frequency Reconfigurable Antenna Design and Analysis with White LED Lamp, Red and Infra-red LEDs

PWM Controlled Servomechanism

Precise control of aircraft flight control surfaces by the pilot is critical to flight safety. The joystick and control surface positions must be detected accurately and quickly, and the motion mechanism must be operated in such a way as to ensure synchronization between them. The analogue voltage value taken from the potentiometer, which is used as a position sensor in many small aircraft, can be used directly or by converting to digital. 
 In this applied study, the analogue position knowledge received from the potentiometer on the joystick was converted into a PWM signal with an oscillator circuit. The PWM position signal applied to the IR (InfraRed) LED in the transmitter unit is sent as infrared light. The PWM position knowledge detected by the photodiode in the receiver unit was passed through the LPF (Low Pass Filter) and the voltage value of the joystick potentiometer was obtained again. With the mechanism controlled according to the difference between the potentiometer values of the joystick and the control surface, the synchronization between the joystick and the control surface is ensured. In this study, a wireless and stable servomechanism connection is obtained by transmitting PWM position knowledge as IR.

Further advancements in the near infrared lightemitting diode: review

During the last decade, significant advances have been made in the application of using a near infrared LED light-emitting diode over the use of low-level laser light therapy for a wide range of healing and rehabilitation processes. Near infrared LED has been shown to represent a novel, non-invasive, and effective coadjutant therapeutic intervention for the treatment of numerous diseases. With the discovery of the use of gallium arsenate (red light), the near infrared light-emitting diode has shown to be an effective therapy in the use of wound, bone, and traumatic brain injuries. Specific applications include wound healing, dentistry, peripheral nerve injury, depression, neurological disease (including Parkinson’s Disease, depression, and dementia), aging cerebrovascular disease, and traumatic brain injury. Most recently, the application of infrared light on brain tumors (photodynamic therapy) has started to provide a positive result. More evidence-based research is required to support this growing coadjutant therapeutic intervention.

Improved Optical Efficiency of 850-nm Infrared Light-Emitting Diode with Reflective Transparent Structure.

This study investigated a reflective transparent structure to improve the optical efficiency of 850 nm infrared light-emitting diodes (IR-LEDs), by effectively enhancing the number of extracted photons emitted from the active region. The reflective transparent structure was fabricated by combining transparent epitaxial and reflective bonding structures. The transparent epitaxial structure was grown by the liquid-phase epitaxy method, which efficiently extracted photons emitted from the active area in IR-LEDs, both in the vertical and horizontal directions. Furthermore, a reflective bonding structure was fabricated using an omnidirectional reflector and a eutectic metal, which efficiently reflected the photons emitted downwards from the active area in an upward direction. To evaluate reflective transparent IR-LED efficiency, a conventional absorbing substrate infrared light-emitting diode (AS IR-LED) and a transparent substrate infrared light-emitting diode (TS IR-LED) were fabricated, and their characteristics were analyzed. Based on the power-current (L-I) evaluation results, the output power (212 mW) of the 850 nm IR-LED with the reflective transparent structure increased by 76% and 26%, relative to those of the AS IR-LED (121 mW) and TS IR-LED (169 mW), respectively. Furthermore, the reflective transparent structure possesses both transparent and reflective properties, as confirmed by photometric and radial theta measurements. Therefore, light photons emitted from the active area of the 850 nm IR-LED were efficiently extracted upward and sideways, because of the reflective transparent structure.

Investigation of Narrow-band NIR LED Spectral Response Towards a Non-invasive Glucose Sensor.

Spectroscopy is utilised extensively in medical sensing technology. Typically, hand-held spectroscopy equipment uses miniature narrow-band light emitting diodes (LEDs) and photodiodes to emit and detect light, respectively. Photodiodes typically absorb light across a wide spectra so measurements can be corrupted by surrounding light. LEDs in the visible spectrum have a narrower spectral response and can be used in place of a traditional photodiode. However, the absorption characteristics of near infrared (NIR) spectrum LEDs is unknown. A discrete, low-cost spectrophotometer was designed to assess spectral response for 8 narrow band NIR LEDs. The normalised and raw spectral response determined the optimum detector for 1050 nm - 1300 nm is the 1450 nm LED, and the optimum detector for 1450 nm - 1650 nm emissions is the 1650 nm LED.Clinical relevance - Understanding the spectral response of narrow-band LEDs in the NIR spectrum will aid development of NIR hand-held spectroscopy medical devices.

A bench-top Dark-Root device built with LEGO® bricks enables a non-invasive plant root development analysis in soil conditions mirroring nature.

Roots are the hidden parts of plants, anchoring their above-ground counterparts in the soil. They are responsible for water and nutrient uptake and for interacting with biotic and abiotic factors in the soil. The root system architecture (RSA) and its plasticity are crucial for resource acquisition and consequently correlate with plant performance while being highly dependent on the surrounding environment, such as soil properties and therefore environmental conditions. Thus, especially for crop plants and regarding agricultural challenges, it is essential to perform molecular and phenotypic analyses of the root system under conditions as near as possible to nature (#asnearaspossibletonature). To prevent root illumination during experimental procedures, which would heavily affect root development, Dark-Root (D-Root) devices (DRDs) have been developed. In this article, we describe the construction and different applications of a sustainable, affordable, flexible, and easy to assemble open-hardware bench-top LEGO® DRD, the DRD-BIBLOX (Brick Black Box). The DRD-BIBLOX consists of one or more 3D-printed rhizoboxes, which can be filled with soil while still providing root visibility. The rhizoboxes sit in a scaffold of secondhand LEGO® bricks, which allows root development in the dark and non-invasive root tracking with an infrared (IR) camera and an IR light-emitting diode (LED) cluster. Proteomic analyses confirmed significant effects of root illumination on barley root and shoot proteomes. Additionally, we confirmed the significant effect of root illumination on barley root and shoot phenotypes. Our data therefore reinforces the importance of the application of field conditions in the lab and the value of our novel device, the DRD-BIBLOX. We further provide a DRD-BIBLOX application spectrum, spanning from investigating a variety of plant species and soil conditions and simulating different environmental conditions and stresses, to proteomic and phenotypic analyses, including early root tracking in the dark.

Study on P-AlGaAs/Al/Au Ohmic Contact Characteristics for Improving Optoelectronic Response of Infrared Light-Emitting Device.

The Al/Au alloy was investigated to improve the ohmic characteristic and light efficiency of reflective infrared light-emitting diodes (IR-LEDs). The Al/Au alloy, which was fabricated by combining 10% aluminum and 90% gold, led to considerably improved conductivity on the top layer of p-AlGaAs of the reflective IR-LEDs. In the wafer bond process required for fabricating the reflective IR-LED, the Al/Au alloy, which has filled the hole patterns in Si3N4 film, was used for improving the reflectivity of the Ag reflector and was bonded directly to the top layer of p-AlGaAs on the epitaxial wafer. Based on current-voltage measurements, it was found that the Al/Au alloyed material has a distinct ohmic characteristic pertaining to the p-AlGaAs layer compared with those of the Au/Be alloy material. Therefore, the Al/Au alloy may constitute one of the favored approaches for overcoming the insulative reflective structures of reflective IR-LEDs. For a current density of 200 mA, a lower forward voltage (1.56 V) was observed from the wafer bond IR-LED chip made with the Al/Au alloy; this voltage was remarkably lower in value than that of the conventional chip made with the Au/Be metal (2.29 V). A higher output power (182 mW) was observed from the reflective IR-LEDs made with the Al/Au alloy, thus displaying an increase of 64% compared with those made with the Au/Be alloy (111 mW).

VEHICLE ACCIDENT AVOIDANCE WITH ROAD ADVERSE CONDITIONS MONITORING SYSTEMS

Accidents are the leading cause of death in emerging nations. Despite the fact that "speed kills," individuals still don't care enough to drive safely on ghat roads. The most pressing issues now are ghat road accidents and the deaths that result from them. There will be sharp turns and narrow roadways on mountain highways. Under these kinds of circumstances, a driver of a vehicle cannot see vehicles and animals travelling on the highways from the other side. This issue results in the deaths of thousands of people and animals every year. The answer to this issue is to warn the driver in the GHATs section of any approaching vehicles or animals. In order to achieve this, "INFRARED SENSORS and LED LIGHTS" are kept on either side of the road before the curve. This way, if a vehicle approaches from one end of the curve, the sensor detects it and the LED light shines on the opposite side. Drivers can be vigilant and reduce vehicle speed by observing the LED light on/off criteria. Keywords- Alerting system, Infrared sensor, LED, Buzzer.

Non-Invasive Classification of Blood Glucose Level Based on Photoplethysmography Using Time–Frequency Analysis

Diabetes monitoring systems are crucial for avoiding potentially significant medical expenses. At this time, the only commercially viable monitoring methods that exist are invasive ones. Since patients are uncomfortable while blood samples are being taken, these techniques have significant disadvantages. The drawbacks of invasive treatments might be overcome by a painless, inexpensive, non-invasive approach to blood glucose level (BGL) monitoring. Photoplethysmography (PPG) signals obtained from sensor leads placed on specific organ tissues are collected using photodiodes and nearby infrared LEDs. Cardiovascular disease can be detected via photoplethysmography. These characteristics can be used to directly affect BGL monitoring in diabetic patients if PPG signals are used. The Guilin People’s Hospital’s open database was used to produce the data collection. The dataset was gathered from 219 adult respondents spanning an age range from 21 to 86 of which 48 percent were male. There were 2100 sampling points total for each PPG data segment. The methodology of feature extraction from data may assist in increasing the effectiveness of classifier training and testing. PPG data information is modified in the frequency domain by the instantaneous frequency (IF) and spectral entropy (SE) moments using the time–frequency (TF) analysis. Three different forms of raw data were used as inputs, and we investigated the original PPG signal, the PPG signal with instantaneous frequency, and the PPG signal with spectral entropy. According to the results of the model testing, the PPG signal with spectral entropy generated the best outcomes. Compared to decision trees, subspace k-nearest neighbor, and k-nearest neighbor, our suggested approach with the super vector machine obtains a greater level of accuracy. The super vector machine, with 91.3% accuracy and a training duration of 9 s, was the best classifier.

A new approach to non-mydriatic portable fundus imaging

ABSTRACT Introduction The present study proposes a new hand-held non-mydriatic fundus camera for retinal imaging. The goal is to design a fundus camera which is equally effective in both clinical and telemedicine scenarios. Areas covered A new retinal illumination approach is proposed to address the main dilemma of the optical design, i.e. balancing efficacy with structural simplicity. This is achieved by symmetrical and co-axial placement of multiple illumination sources along the optical pathway. Each illumination source includes a white and a Near Infra-Red (NIR) LED, which are placed adjacent to each other. Hence, the camera can produce a view-finder with NIR illumination without the need for additional beam-splitters and filters. Expert Opinion The proposed design blends the structural simplicity of the ‘off-axis illumination with the wide field of view and uniform illumination of the ‘ring’ illumination. Moreover, the camera is designed to work with Android-based smartphones, which can easily be mounted and interfaced. The efficacy of the proposed camera is determined by ocular safety analysis and comparative evaluation with a table-top fundus camera. The results convincingly demonstrate the ability of the proposed camera as a primary driver of a wide-scale screening program in both clinical and remote resource constraint environments.

Evaluation of a Vein Biometric Recognition System on an Ordinary Smartphone

Nowadays, biometrics based on vein patterns as a trait is a promising technique. Vein patterns satisfy universality, distinctiveness, permanence, performance, and protection against circumvention. However, collectability and acceptability are not completely satisfied. These two properties are directly related to acquisition methods. The acquisition of vein images is usually based on the absorption of near-infrared (NIR) light by the hemoglobin inside the veins, which is higher than in the surrounding tissues. Typically, specific devices are designed to improve the quality of the vein images. However, such devices increase collectability costs and reduce acceptability. This paper focuses on using commercial smartphones with ordinary cameras as potential devices to improve collectability and acceptability. In particular, we use smartphone applications (apps), mainly employed for medical purposes, to acquire images with the smartphone camera and improve the contrast of superficial veins, as if using infrared LEDs. A recognition system has been developed that employs the free IRVeinViewer App to acquire images from wrists and dorsal hands and a feature extraction algorithm based on SIFT (scale-invariant feature transform) with adequate pre- and post-processing stages. The recognition performance has been evaluated with a database composed of 1000 vein images associated to five samples from 20 wrists and 20 dorsal hands, acquired at different times of day, from people of different ages and genders, under five different environmental conditions: day outdoor, indoor with natural light, indoor with natural light and dark homogeneous background, indoor with artificial light, and darkness. The variability of the images acquired in different sessions and under different ambient conditions has a large influence on the recognition rates, such that our results are similar to other systems from the literature that employ specific smartphones and additional light sources. Since reported quality assessment algorithms do not help to reject poorly acquired images, we have evaluated a solution at enrollment and matching that acquires several images subsequently, computes their similarity, and accepts only the samples whose similarity is greater than a threshold. This improves the recognition, and it is practical since our implemented system in Android works in real-time and the usability of the acquisition app is high.

Beneficial effects of infrared light-emitting diode in corticosteroid-resistant asthma.

Corticosteroid-resistant asthma (CRA) is a severe form of disease and clinically important, since patients do not respond to mainstay corticosteroid therapies. Thus, new therapies are needed. However, a big limiting factor in the understanding of CRA is the existence of different immunological and inflammatory phenotypes, a fact that makes it difficult to reproduce experimentally. Photobiomodulation (PBM) emerges as an alternative therapy based on earlier studies. This study aims to evaluate the effect of PBM using infrared light-emitting diode (ILED) on the development of corticosteroid-resistant asthma. Therefore, groups of rats were sensitized and challenged with ovalbumin plus Freund's adjuvant for the induction of CRA, and treated or not with ILED directly in the respiratory tract on the skin (wavelength 810 nm; power 100 mW; density energy 5 J/cm; total energy 15 J; time 150 s). Our experimental model was capable to induce neutrophilic asthma. Besides that, the corticosteroid treatment did not reverse the lung cell migration as well as the levels of leukotriene B4, and interleukins 17 and 6. The treatment with ILED reduced the lung cell migration; myeloperoxidase activity; mast cell degranulation; and the levels of leukotriene B4, thromboxane B2, prostaglandin E2, tumoral necrosis factor alpha, and interleukins 17 and 6. Still, ILED increased the level of interleukin 10. In conclusion, we showed promisor effects of ILED when irradiated directly in the respiratory tract as adjuvant treatment of corticosteroid-resistant asthma.

Heat-resistant reflectors for enhanced 850-nm near infrared light-emitting diode efficiency

This study investigated the use of heat-resistive reflectors to improve the efficiency of wafer-bonded reflective 850 nm infrared light-emitting diodes (LEDs). The Au-based heat-resistive reflectors were synthesized with added Ni, Ti, Cu, and Al, and heat treated at 450 °C. The Al/Au alloyed reflector exhibited the highest reflectivity of nearly 90% when incorporated into the wafer-bonded epi-layer (Al0.3Ga0.7As/GaP). Further, the output power of 850 nm LED chips based on the pure Au and alloyed reflectors were compared, where the Al/Au alloyed reflector led to a 1.4-fold increase in output power compared to the pure Au reflector. This increase is attributed to enhanced heat-resistant reflectivity of the Al/Au alloyed reflector. Therefore, the Al/Au alloyed reflector shows promise for the development of more efficient reflective infrared LEDs.

Photons from NIR LEDs can delay flowering in short-day soybean and Cannabis: Implications for phytochrome activity.

Photons during the dark period delay flowering in short-day plants (SDP). Red photons applied at night convert phytochromes to the active far-red absorbing form (Pfr), leading to inhibition of flowering. Far-red photons (greater than 700 nm) re-induce flowering when applied after a pulse of red photons during the dark period. However, far-red photons at sufficiently high intensity and duration delay flowering in sensitive species. Mechanistically, this response occurs because phytochrome-red (Pr) absorbance is not zero beyond 700 nm. We applied nighttime photons from near infrared (NIR) LEDs (peak 850 nm) over a 12 h dark period. Flowering was delayed in Glycine max and Cannabis sativa (two photosensitive species) by 3 and 12 days, respectively, as the flux of photons from NIR LEDs was increased up to 83 and 116 μmol m-2 s-1. This suggests that long wavelength photons from NIR LEDs can activate phytochromes (convert Pr to Pfr) and thus alter plant development.

Alkalis-doping of mixed tin-lead perovskites for efficient near-infrared light-emitting diodes

Substitution of lead (Pb) with tin (Sn) is a very important way to reduce the bandgap of metal halide perovskite for applications in solar cells, and near infrared (NIR) light-emitting diodes (LEDs), etc. However, mixed Pb/Sn perovskite becomes very disordered with high trap density when the Sn molar ratio is less than 20%. This limits the applications of mixed Pb/Sn perovskites in optoelectronic devices such as wavelength tunable NIR perovskite LEDs (PeLEDs). In this work, we demonstrate that alkali cations doping can release the microstrain and passivate the traps in mixed Pb/Sn perovskites with Sn molar ratios of less than 20%, leading to higher carrier lifetime and photoluminescence quantum yield (PLQY). The external quantum efficiency (EQE) of Sn0.2Pb0.8-based NIR PeLEDs is dramatically enhanced from 0.1% to a record value of 9.6% (emission wavelength: 868 nm). This work provides a way of making high quality mixed Pb/Sn optoelectronic devices with small Sn molar ratios.

Warming of blood and intravenous fluids using low-power infra-red light-emitting diodes

Non-contact warming of blood and intravenous (IV) fluids with temperature drop compensation is an unmet clinical need till now, for management of hypothermia in patients with urgent requirement of blood. Currently available technologies provide wet warming or dry warming with direct contact using hot water or with a hot plate, respectively. These conventional technologies need disposable cartridges to be used in conjunction with the warmer. The warmed fluids lose their temperature when passing through long IV lines and fails in its purpose at low flow rates. In this paper, a distributed non-contact warming method is introduced using infra-red radiations. The method incorporates a bag warming unit and an inline cartridge unit. Bag warming unit provides uniform distribution of infra-red thermal energy liberated from low cost infra-red light emitting diodes (IR LEDs) in horizontal and vertical planes of the fluid carrying bag. An inline cartridge, through which the IV line passes, reduces the drop in temperature just before the transfusion site using a cluster of IR LEDs. As per the In Vitro tests are carried out in to establish the safety and efficacy, the bag warming unit steadily rises the temperature to attain the cut off value with a temperature rise coefficient of 0.7 °C/min and the inline cartridge warms the fluid within 10 min at a thermal transfer rate of more than 1.5 °C/min. The fluid temperature is uniformly distributed within a narrow range of 36–38 °C. When the inline warmer is powered on, the drop-in temperature is reduced to zero for flow up to 5 ml/min. For flow rates more than 8 ml/min, the temperature drop is reduced more than half. For massive transfusion range, the temperature of the fluid remains within 38.5 ± 1.2 °C for flow rates in the range of 100–1500 ml/min.

Low-level red plus near infrared lights combination induces expressions of collagen and elastin in human skin in vitro.

Light therapy has attracted medical interests as a safe, alternative treatment for photo-ageing and photo-damaged skin. Recent research suggested the therapeutic activity of red and infrared (IR) lights may be effective at much lower energy levels than those used clinically. This study was to evaluate the efficacy of low-level red plus near IR light emitting diode (LED) combination on collagen and elastin and ATP production. Human dermal fibroblasts or skin tissues were irradiated daily by red (640nm) plus near IR (830nm) LED lights combination at 0.5mW/cm2 for 10minutes (0.3J/cm2 ). qPCR, ELISAs or histology were used to determine the gene and protein expressions. Fluorescent measurement was used to assess crosslinks of collagen and elastic fibres. ATP production was evaluated by ATP assay. Treatment of human fibroblast cell cultures with low-level red plus near IR lights combination was found to significantly increase LOXL1, ELN and COL1A1 and COL3A1 gene expressions as well as the synthesis of the procollagen type I and elastin proteins. Treating human skin explants with low-level red plus near IR lights combination similarly induced significant increases in the same gene expressions, type III collagen and elastic fibre formation and crosslinks. ATP production was increased in human dermal fibroblasts after red plus near IR lights combination treatment. Low-level red plus near IR lights combination stimulated the production of collagen and elastin production associated with anti-ageing benefits. These findings suggest that low-level red plus near IR LED light combination may provide an effective treatment opportunity for people with photo-aged skin.

PICUS: A Pocket-Sized System for Simple and Fast Non-Destructive Evaluation of the Detachments in Ancient Artifacts

An innovative, robust method has been developed, based on the use of a simple, compact, expressly designed device, named PICUS (the ‘woodpecker’ in ancient Latin), and inspired by the auscultation method carried out by the experts in the field of conservation of cultural heritage. This method entails gently knocking the surface, controlling and measuring the impact time of the stroke’s force, recording the generated sound, comparing the acquired sound with a reference sound by calculating the cross-correlation function, and its maximum, as a measure of the detachment. In a nutshell, it performs an analysis similar to that carried out by a professional who performs a routine examination on the detachments by hand. The experimental apparatus consists of a probe made of an electromechanical percussion element that gently taps the surface producing a sound, a force sensor purposely developed to measure the impact force, and a microphone, all connected with an Arduino-like low cost board, to record and elaborate the sounds and the force sensor signal. The probe XY position on the scene is recognized using an infra-red (IR) system with a low-cost IR camera and an IR light-emitting diode (IR-LED) positioned on the probe. The “tapper” and the microphone replace the hand and the ear of a conservator carrying out a detachment investigation, while the comparison with a reference is the typical mind process of a professional restorer. The result is the fusion of the microphone data and the force sensor data.