Industrial Waste Incineration Research Articles

Mineralization of fluoropolymers from combustion in a pilot plant under representative european municipal and hazardous waste combustor conditions

The goal of this study was to provide data to support mineralization of fluoropolymer waste and insignificant generation of PFAS as products of incomplete combustion (PIC) during incineration of fluoropolymer applications at their end-of-life. Destruction efficiency is not an acceptable metric to indicate mineralization and therefore we need to look for and measure products of incomplete destruction. A mixed sample of fluoropolymers representing 80% of commercial fluoropolymers was combusted at conditions representative of municipal and industrial waste incinerators operating in EU. State-of-the-art emission sampling and analytical methods (UPLC-MS/MS, GC-MS) were used for identifying and quantifying those PFAS whose standards were available. Statistical analysis of the results confirmed non-detect to negligible levels of PFAS evidencing mineralization of fluoropolymers.

Discharge Electrode Degradation in Dry Electrostatic Precipitator Cleaning of Exhaust Gases from Industrial Solid Waste Incinerators

The electrodes of industrial electrostatic precipitators degrade as a result of two phenomena: corrosion and erosion. The first is chemical degradation by highly reactive compounds formed during combustion, in particular, during the incineration of municipal or industrial wastes or high-sulfur coal. The degradation intensity of electrostatic precipitator electrodes depends on the chemical composition of the exhaust gasses. High concentrations of chlorides, fluorides, or sulfur in the exhaust gasses cause strong corrosion of the electrostatic precipitator elements. The second mechanism is the erosion caused by solid particles conveyed by the exhaust gas stream due to their collision with the electrodes. In this study, the analysis of the degradation of electrodes of an electrostatic precipitator downstream of an industrial waste incinerator was carried out. The industrial wastes of unknown sources were subjected to thermal degradation in a rotary kiln. The aim of this study was to provide fundamental knowledge about the mechanisms of electrode degradation located on the surface of discharge electrodes of electrostatic precipitators during the combustion of industrial wastes.

Đánh giá mức độ phát thải của các chất polyclodibenzo-p-dioxin và polyclodibenzofuran phát sinh không chủ định từ lò đốt rác chất thải sinh hoạt và rác thải công nghiệp ở Việt Nam

Polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) are the most toxic substances among the group of unintentional persistent organic pollutants (U - POP) generated from many sources, in which domestic and industrial waste incinerators are the highest emission risk. Assessment of pollution potential and dioxin/furan emissions from incinerators in developing countries, including Vietnam, is still limited; especially in-depth studies on the content and characteristics of PCDD/PCDF emitted into the atmosphere. Therefore, the research team evaluated the emission potential and characteristics of 07 PCDD and 10 PCDF, those are considered to be the most toxic isomers and congeners, from stack gas samples collected from incinerators at 33 facilities in 11 provinces in Vietnam. The total concentration of PCDD/PCDF in the industrial incinerators’ emission ranged from 37.3 to 3348.6 pg TEQs/m3 and domestic waste incinerators had lower total concentrations and fluctuated within about 37.3-1323.8 pg TEQs/m3. The characteristic of incinerator emissions is that the proportion of 2,3,7,8- TCDD accounts for 2.9 to 9.04%. The highest contributing concentrations were congeners 1,2,3,7,8-PeCDD, with its contributing percentage from 22.95-32.42%. The second largest contributor is congeners 2,3,4,7,8- PeCDF, accounting for 20.94- 21.50% of the total toxic congeners of PCDD/PCDF in both types of incinerators. However, in terms of toxic equivalency (TEQ), the concentration of industrial waste incinerators is much higher than that of domestic waste incinerators. The results of stack gas samples showed that the PCDD/PCDF content for domestic waste incinerators has 5/17 establishments that exceeded the permissible standard threshold: 0.6 ng/Nm3, according to QCVN 61-MT:2016/BTNMT. Industrial waste incinerators have 5/16 establishments that exceeded the permissible standard threshold: 0.6ng/Nm3 for furnaces with a capacity of 300kg/hour according to QCVN 30:2012/BTNMT.

An empirical study on thermal efficiency and dusty moisture removal efficiency using enthalpy wheel in industrial waste incineration plant

In this work, an empirical study is conducted on the waste heat recovery and moisture removal performance of an enthalpy wheel installed in an industrial waste incineration plant. The enthalpy wheel made of a metal mesh is placed in parallel with the wet scrubber of the incineration plant to exchange heat with high-temperature exhaust at 200 °C. In the enthalpy wheel, exhaust gas and external air exchange heat in the form of a counter flow, and the condensation effect is maximized by installing a water-spray nozzle at the inlet of the enthalpy wheel. Empirical data were collected over 100 days spanning July to October. To evaluate the performance of the enthalpy wheel, thermal efficiency, moisture removal efficiency, and dust removal efficiency were tested under high-temperature humid conditions. In some results, the overall thermal efficiency reached peaked at 61.2 %. Regarding moisture removal performance, the average moisture removal rate was 493 kg/h, affording an efficiency of 49.2 %. In terms of dust removal performance, the average dust removal efficiency was 79.6 %.

Insights into Full-congener Profiles of Chlorinated Benzenes in Fly and Bottom Ash: Case Study in Vietnamese Industrial and Municipal Waste Incinerators.

Chlorinated benzenes (CBzs) are a group of organic pollutants, which have been industrially or unintentionally produced through various chemical and thermal processes. Studies on full congener profiles of CBzs in waste and environmental samples are relatively limited and not updated. In the present study, concentrations of 12 CBzs were determined in fly ash (FA) and bottom ash (BA) samples collected from one municipal waste incinerator (MWI) and one industrial waste incinerator (IWI) in northern Vietnam. Levels of Σ12CBzs were higher in bottom ash (median 25.3; range 1.59-45.7 ng/g) than in fly ash (median 7.30; range 1.04-30.0 ng/g). The CBz profiles were dominated by di- and tri-chlorinated congeners with the major congeners as 1,2,4-TCB, 1,2,3-TCB, 1,2-DCB, and 1,3-DCB. However, CBz profiles varied greatly between sample types and incinerators, implying differences in input materials, formation pathways, and pollutant behaviors. Incomplete combustion is possibly responsible for high levels of CBzs in industrial bottom ash. The emission factors of Σ12CBzs ranged from 21 to 600µg/ton for fly ash and from 190 to 4570µg/ton for bottom ash, resulting in annual emissions of about 6 and 3g/year for the IWI and MWI, respectively. Our results suggest additional investigations on industrial emission and environmental occurrence of all 12 CBzs rather than solely focusing on regulated congeners like hexachlorobenzene and pentachlorobenzene.

Insight into heavy metal chemical fractions in ash collected from municipal and industrial waste incinerators in northern Vietnam.

This investigation involved the collection of fly ash and bottom ash specimens from seven waste incinerators situated in the northern provinces of Vietnam, aimed at assessing the composition and distribution patterns of five chemical fractions of heavy metals (Pb, Cr, As, Cd Cu, and Zn) present in incinerator waste ash. The outcomes reveal that fly ash exhibited a relatively elevated concentration of industrial waste metals (25-66%) such as As, Cd, and Pb primarily in exchangeable (F1) and carbonate fractions (F2), which are mobile forms susceptible to environmental dissolution and consequential bioaccumulation posing health risks to humans. The predominant states of the metals Cr, Cu, and Zn were identified as residual, Fe-Mn oxide, and carbonate, respectively, with their relative proportions showing minimal variation. Conversely, heavy metals were predominantly present in residual residue and Fe-Mn bound form (F3) in bottom ash derived from both residential and commercial waste incineration operations. The non-carcinogenic hazard indices (HI) associated with the examined metals, ranked for both adults and children, were as follows: Pb > Cr > As > Cd > Cu > Zn. Notably, the HI values for Pb, Cr, and As exceeded the permissible threshold (HI > 1) for children. However, the risk of As, Cd, and Pb-related cancer via exposure pathways remained within acceptable limits for both age groups. Conversely, the probability of carcinogenic effects attributable to Cr surpassed the permissible threshold (>10-4), indicating significant health concerns associated with heavy metals in waste incinerators for humans, particularly children.

Modification of Recycled Industrial Solid Waste Incineration Fly Ash as a Low-cost Catalyst for NOx Removal

Modification of Recycled Industrial Solid Waste Incineration Fly Ash as a Low-cost Catalyst for NOx Removal

Sustainable ceramic tiles incorporated with waste fly ash from recycled paper production

Waste incineration is an effective solid waste disposal method; however, its by-product pollutants hinder its widespread adoption. This research aims to develop novel unglazed ceramic tiles by recycling industrial solid waste incineration fly ash (IWA) from recycled paper mills. Experimental investigations were conducted on ceramic tiles with IWA additions (0–30 wt%) and firing temperatures (1100 °C, 1200 °C, and 1300 °C). Various scientific tests, including XRF, XRD, strength, water absorption, thermal properties, heavy metal leaching, SEM analysis, and micro-CT analysis, were performed. The results suggest that the addition of IWA may deteriorate the technical performance of ceramic tiles; however, satisfactory performance can still be achieved by tailoring the firing temperature due to the existence of iron and calcium in the IWA, which narrows and displaces the densification temperature range. Remarkably, tiles with 30 wt% IWA, which completely replaced the flux materials and fired at 1300 °C, achieved the highest flexural strength (exceeding 30 MPa). These tiles exhibited promising attributes such as water absorption of 5.9%, an estimated energy saving of 33.86%, and compliance with heavy metal leaching limits. This study proposes a sustainable solution for IWA disposal by utilising recycled paper mill fly ash as a substitute for flux material in ceramic tile manufacturing. The findings contribute to minimising environmental impact and conserving non-renewable natural resources, supporting sustainable development.

Troubleshooting dioxins stack emissions in an industrial waste gas incinerator

An important source of dioxins and furans at present is waste incineration, utmost formed during combustion processes and emitted to the environment without being fully captured by waste-gas treatment equipment. In this study, monitoring campaign of International Toxic Equivalents for dioxins and furans (I-TEQDF), was carried out at pharmaceutical industrial waste incinerator to find a correlation between combustion parameters and feed composition with potential emission. Principal Component Analysis (PCA) shows that high values of dioxin emission correlate with short residence time of the flue gas in the furnace as well as low oxygen concentration. These operating conditions were further investigated, using COMSOL Computational Fluid Dynamics (CFD) simulation to calculate the temperature profiles along the furnace. The results suggest that the flame temperature profile is anticipated to exhibit cold areas (cold spots), which may be used as a proxy for dioxin formation due to incomplete combustion. Additionally, the calculated congeners furan to dioxin concentration ratio, points to their formation via de novo mechanism. SEM-EDS analysis preformed on the bag filter upstream the feed following its filtration, have shown large amount of iron, which may have served as a metal catalytic source for dioxin formation. The iron origin is most likely from corrosion of the feeding pipe, drifted with the waste gas and trapped on the bag filter. The results of this study provide a better understanding of the parameters controlling dioxin formation and emission from the plant and may assist a planning of process optimization in such a plant.

Composition modification and plasma vitrification of bottom ash from industrial hazardous waste incineration

Industrial hazardous waste (IHW) incineration bottom ash (BA) contains high-content acidic oxides and a limited amount of basic oxides. This contributes to the vitrification of the BA sample, although it causes a high melting temperature and viscosity. Unfortunately, basic fluxing agents play a negative role in the durability of glassy slag. Hence, the industrial BA melting process requires a comprehensive and accurate composition modification method. In this study, the basicity, complete liquid phase temperature, and viscosity-temperature performance of a BA sample were investigated. The BA sample was melted using a thermal plasma system. Furthermore, environmental sound quality analysis was performed, including the toxicity characteristic leaching procedure and acid loss rate. The results indicate that the BA sample may be directly vitrified, although the melting temperature and viscosity need to be modified. Comprehensively, it was found that 15% CaO addition is the most suitable choice. The BA composition modification sample melted completely, slagging smoothly, transformed mostly to the vitrification state, and the index values of the environmental sound quality analysis were dramatically reduced. It has been proven that appropriate composition modification can not only guarantee the stable BA melting process but also favor the vitrification and solidification of heavy metals.

Multiblock dynamic enhanced canonical correlation analysis for industrial MSW combustion state monitoring

Combustion state monitoring in industrial municipal solid waste incineration (MSWI) power generation process is very difficult. There are two main reasons for this dilemma: (1) there is a large time lag between the combustion chamber and the steam generation stage; (2) reactions continue to occur and raw waste is fed into the incinerator continuously, so there are strong correlations and remarkable dynamic characteristics among process variables. The complex correlations in time and in space cause difficulties in combustion state monitoring for incinerators. Those correlations are common in industrial processes because the large scale equipment is usually needed and a whole process is realized by equipment in sequence. To overcome those difficulties, a multi-block dynamic enhanced canonical correlation analysis (MBDCCA) method is proposed to help monitor the MSWI process. Firstly, canonical correlation analysis (CCA) is extended to MBDCCA to model the MSWI process. Secondly, a combustion state online monitoring approach is designed based on the proposed MBDCCA algorithm. Finally, the proposed method is applied in an industrial MSWI plant to demonstrate the effectiveness.

The impact of pollutant emissions from co-incineration of industrial waste in municipal solid waste incinerators

A large amount of industrial solid waste (including waste plastics, textiles, wood, etc., which are byproducts of industrial production) urgently needs to be treated. Incineration is undoubtedly the most efficient and convenient method. The existing municipal solid waste incineration plants can be transformed to burn such industrial wastes. However, the potential risks associated with high levels of heavy metals in industrial waste and the air pollution caused by co-incineration pose significant challenges to the co-incineration disposal of industrial solid waste. The change of physical and chemical properties of municipal solid waste and the emission characteristics of flue gas pollutants after co-incineration of industrial waste were studied by means of material flow simulation and experiment. In addition, experiments were designed to study the effects of temperature, calcium sulfur ratio and chlorine content on heavy metal emission during the incineration of industrial waste. The results showed that co-incineration of a certain proportion of industrial waste significantly increased the calorific value of municipal solid waste, but excessive mixing of plastic and paper industrial waste would increase the ash content. Co-incineration of plastic industrial waste can significantly increase HCl, and with the increase of temperature, the transformation of Cl to HCl is more thorough. The increase of temperature can promote the migration of Cr, Pb and Se elements to the gas phase. When Cr, Pb, and Se elements are present in the gas phase, they can combine with other gases and aerosols to form particulate matter and toxic substances, causing air pollution. When Ca/S is 1, Ba, Mn, Ni, Zn can effectively reduce the retention rate of elements in the ash. Under certain conditions, chlorine in industrial waste plastics will react with Zn to form tiny particles and low boiling point chlorides, which will increase its volatility. The mineral components in the ash can also be used for making ceramsite and building materials. These results will provide reference for the pollutants controlling during co-incineration of industrial waste and municipal solid waste process.

Long-Term Leaching Behavior and Geochemical Modeling of Cement Solidified Incineration Fly Ash Containing Waste Tires and Wood Biomass

Waste incineration is a widely used treatment method, and sustainable approaches are required to properly recycle large volumes of incineration ash to reduce environmental impacts and landfill space consumption. Studies have focused on the potential of recycling incineration ash as a replacement for natural aggregates in civil engineering applications, such as road construction. However, industrial waste incineration ash, such as waste tire incineration ash, contains hazardous heavy metals, such as lead and zinc that pose potential environmental threats. Moreover, few studies have investigated the leachability of these hazardous metals after long-term natural aging. This study investigates the long-term evolution of leachate chemistry, mineralogical transformation, and heavy metal fixation performance of a recycled roadbed material using ash from industrial waste incineration of waste tires and biomass (SFA). Additionally, field samples from a five-year pilot test site utilizing SFA were also examined. Regulatory leaching tests showed that the concentrations of Cd, Pb, As, T-Cr, and Ni were all below permissible limits even after five years of utilization. Long-term column leaching experiment results indicated that, compared to the total content of the SFA material, the leaching ratios of Pb, T-Cr, Cu, and Zn were 27%, 12%, 5%, and 0.1%, respectively. The SFA pH-stat leaching test results demonstrated that the mass release of the total content of heavy metals was relatively minimal, even under acidic pH conditions (pH < 4). Finally, profiles of pH and major ions in leachate from the column leaching experiment were simulated using HYDRUS HP1, implementing a dual-porosity modeling approach. In conclusion, despite containing hazardous heavy metals, SFA exhibits significantly low leaching rates over a long-term period.

Mineral phase transition characteristics and its effects on the stabilization of heavy metals in industrial hazardous wastes incineration (IHWI) fly ash via microwave-assisted hydrothermal treatment

Toxic heavy metals in industrial hazardous waste incineration (IHWI) fly ash can be effectively stabilized by using microwave-assisted hydrothermal technology. However, few works have focused on the relationship between mineralogical conversion and stability of heavy metals of fly ash during hydrothermal process. This study investigated the effect of mineral phase transition process on the stabilization and migration behavior of heavy metals in IHWI fly ash using coal fly ash as silicon‑aluminum additive. Mineral composition analysis reveals that after microwave-assisted hydrothermal treatment (MAHT) of IHWI fly ash, zeolite-like minerals (e.g., tobermorite, katoite and sodalite), secondary aluminosilicate minerals (e.g., prehnite and anorthite) and other newly-formed minerals (e.g., wollastonite, pectolite and larnite) were found. The leaching concentrations of heavy metals (Cr, Ni, Cu, Zn, Cd and Pb) in IHWI fly ash decrease sharply after MAHT with the most obvious decreases in Cu, Pb and Zn. Spearman correlation analysis show significantly negative correlation between the content of zeolite-like minerals and the leaching concentrations of most heavy metals (e.g., Ni, Cu, Zn, Cd and Pb). These results suggest that the immobilization effects of heavy metals in IHWI fly ash can be effectively enhanced by promoting the formation of zeolite-like minerals during the MAHT. This study is expected to further promote the development of IHWI fly ash harmless treatment technology.

Au nanocakes as a SERS sensor for on site and ultrafast detection of dioxins

Dioxin is a highly toxic and carcinogenic pollutant created during industrial production and waste incineration. Pollutant monitoring has made extensive use of surface-enhanced Raman spectroscopy (SERS) as a quick, non-destructive, sensitive, and affordable analytical method. However, the fabrication of a SERS substrate with ultrahigh sensitivity is a challenging task, the detection cost is expensive. Currently, these are the challenges faced by SERS technique for the detection of dioxin pollutants. In this paper, we present Au nanocakes (Au NCs) as an easy-to-build SERS substrate for sensitive SERS detection of dioxins in real samples. Based on three-dimensional finite-difference time-domain (3D-FDTD) calculations, the enhancement factor of the substrate following aggregation is approximately 1010. Using a portable Raman spectrometer, the limit of detection for dioxins such as 1-chloro-dibenzo-p-dioxin (1-CDD), 2,8-dichloro-dibenzo-p-dioxin (2,8-DCDD), and 2,3,7-trichloro-dibenzo-p-dioxin (2,3,7-TrCDD) in clean water reached as low as 5, 5, and 10 ng/mL, respectively. As a real-world application, the same toxic pollutants were detected in sewage water samples. Our findings could lead to the development of novel SERS-based sensors for the rapid detection of dioxins in real-world scenarios. Moreover, a portable Raman spectrometer is used to detect the pollutants, which is easy to use and inexpensive.

Exposure to Hazardous Substances and Their Health Effects Among Residents Living Near Three Industrial Waste Incinerators in Korea.

This study aimed to evaluate exposure to various hazardous substances emitted by incineration facilities and their likely effect on the health for residents of Bugi-myeon, Cheongju, Korea, which has three incineration facilities. Heavy metals, polycyclic aromatic hydrocarbons (PAHs), and dioxin concentrations in the air and soil of exposed and control areas were measured. Moreover, the exposure levels to harmful substances and its effects on health were investigated in 1,124 exposed and 232 control adults. PAHs and dioxin concentrations in the air in the exposed area were significantly higher than in the control area. Urinary cadmium and PAHs metabolite concentrations were significantly higher in the exposed group than in the control group. The exposure group also had a higher prevalence of depression and self-reported allergic symptoms than the control group. The possibility of residents in Bugi-myeon being exposed to hazardous substances at incineration facilities cannot be ruled out. To prevent them from further exposure to hazardous substances, it is necessary to prohibit the expansion of additional incineration facilities in this area and to implement continuous monitoring projects for residents.

Emission and distribution profiles of polycyclic aromatic hydrocarbons in solid residues of municipal and industrial waste incinerators, Northern Vietnam.

The concentrations and profiles of 18 polycyclic aromatic hydrocarbons (PAHs) in particulate matter (PM10), fly ash (FA), and bottom ash (BA) were examined in three incineration residues. Samples were collected from different municipal and industrial solid waste incinerators in Northern Vietnam. The average concentrations of total PAHs in PM10, fly ash, and bottom ash were 9.55 × 103ng/Nm3, 215 × 103ng/g, and 2.38ng/g, respectively. Low-molecular-weight PAHs (2 to 3 rings) were predominant in most samples. The emission factor of total PAHs decreased in the order of FA > BA > PM10. A higher concentration of total PAHs was found in industrial facilities than that in municipal ones. The high carcinogenic proportion of PAHs together with significantly high annual emissions reflect the high pollution risk to the ecosystem by PAHs in the case of reuse of incineration ashes (e.g., brick production). Regarding the carcinogenic risk of PAH-bounded ashes or particles, calculations from this study imply the significant threat for workers who have been manipulated in the incineration facilities, directly exposed to fly and bottom ashes. Meanwhile, the risk from PAH-bound particulate was not considered a significant threat for both normal adults and children. Further study on PAHs contained in incinerator waste dumps should be conducted in Vietnam to assess the potential contamination risk of these incineration by-products.

Biological Effects of Human Exposure to Environmental Cadmium

Cadmium (Cd) is a toxic metal for the human organism and for all ecosystems. Cd is naturally found at low levels; however, higher amounts of Cd in the environment result from human activities as it spreads into the air and water in the form of micropollutants as a consequence of industrial processes, pollution, waste incineration, and electronic waste recycling. The human body has a limited ability to respond to Cd exposure since the metal does not undergo metabolic degradation into less toxic species and is only poorly excreted. The extremely long biological half-life of Cd essentially makes it a cumulative toxin; chronic exposure causes harmful effects from the metal stored in the organs. The present paper considers exposure and potential health concerns due to environmental cadmium. Exposure to Cd compounds is primarily associated with an elevated risk of lung, kidney, prostate, and pancreatic cancer. Cd has also been linked to cancers of the breast, urinary system, and bladder. The multiple mechanisms of Cd-induced carcinogenesis include oxidative stress with the inhibition of antioxidant enzymes, the promotion of lipid peroxidation, and interference with DNA repair systems. Cd2+ can also replace essential metal ions, including redox-active ones. A total of 12 cancer types associated with specific genes coding for the Cd-metalloproteome were identified in this work. In addition, we summarize the proper treatments of Cd poisoning, based on the use of selected Cd detoxifying agents and chelators, and the potential for preventive approaches to counteract its chronic exposure.

Leaching behavior and mineral speciation of cement-solidified boiler fly ash from industrial waste incineration containing waste tires

Leaching behavior and mineral speciation of cement-solidified boiler fly ash from industrial waste incineration containing waste tires

Cancer risk in the residents of a town near three industrial waste incinerators in Korea: a retrospective cohort study.

Three industrial waste incinerators (IWIs) were built in 1999, 2001, and 2010, within a 3km radius of a town with a population of around 5000 in Korea. This study evaluated whether residents near these three IWIs had increased cancer incidence than those from other areas in Korea using regional health data. Standardized incidence ratios (SIR) were calculated using the frequency of cancer cases in the National Cancer Registry of the exposed area (Buki-myeon), Chungcheongbuk-do (Chungbuk, state including Buki-myeon), and whole Korea from 1999 to 2017. A retrospective cohort was created using National Health Insurance System data from 2002 to 2018. The exposed group was defined as those having a residential history in the exposed area. The control group was defined as those having a residential history in nearby towns or counties in Chungbuk, excluding counties having living and cultural areas in other provinces and cities. Hazard ratio (HR) and 95% confidence intervals (CI) were estimated using the Cox proportional hazard model adjusted for age, level of health insurance fee, and smoking history. In the ecological study using National Cancer Registry data, the risk of all cancers, all cancers excluding thyroid, esophageal, stomach, and lung cancers in the exposed area were 1.13 (95% CI 1.03-1.24), 1.15 (95% CI 1.04-1.26), 1.91 (95% CI 1.13-2.89), 1.39 (95% CI 1.14-1.66), and 1.29 (95% CI 1.03-1.57) times higher than in whole Korea among exposed males, respectively. In the retrospective cohort, 4300 males (26,821 person-years) and 3796 females (24,746 person-years) in exposed group, 150,964 males (1,212,010 person-years) and 134,535 females (1,104,025 person-years) in control group were analyzed. After adjusting for several confounding factors, the risks for gallbladder cancer among males and kidney cancer among females were 2.65 (95% CI 1.38-5.06) and 2.82 (95% CI 1.13-7.03) times higher in the exposed group versus the control group, respectively. Cancer risk was higher in Koreans having residential history living near IWIs compared to the other areas. Further study warrants nationwide effects and longer follow-up of WIs for cancers in Korea.