Inductive Link Research Articles

A Wireless Miniature Injectable Device with Memory-Assisted Backscatter for Multimodal Animal Physiological Monitoring.

This paper introduces a wirelessly powered multimodal animal physiological monitoring application-specific integrated circuit (ASIC). Fabricated in the 180 nm process, the ASIC can be integrated into an injectable device to monitor subcutaneous body temperature, electrocardiography (ECG), and photoplethysmography (PPG). To minimize the device size, the ASIC employs a miniature receiver (Rx) coil for wireless power receiving and data communication through a single inductive link operating at 13.56 MHz. We propose a folded L-shape Rx coil with improved coupling to the transmitter (Tx) coil, even in the presence of misalignment, and enhanced quality factor. The ASIC functions alternatively between recording and sleeping modes, consuming 2.55 μW on average. For PPG measurements, a reflection-type PPG sensor illuminates an LED with tunable current pulses. A current-input analog frontend (AFE) amplifies the current of a photodiode (PD) with 30.8 pARMS current input-referred noise (IRN). The ECG AFE captures ECG signals with a configurable gain of 45-80 dB. The temperature AFE achieves 0.02 ̊C inaccuracy within a sensing range between 27-47 ̊C. The AFE outputs are sequentially digitized by a 10-bit successive approximation register (SAR) analog-to-digital converter (ADC) with an effective number of bits (ENOB) of 8.79. To improve the reliability of data transmission, we propose a memory-assisted backscatter scheme that stores ADC data in an off-chip memory and transmits it when the coupling condition is stable. This scheme achieves a package loss rate (PLR) lower than 0.2% while allowing 24-hour data storage. The device's functionality has been evaluated by in vivo experiments.

A Design Review for Biomedical Wireless Power Transfer Systems with a Three-Coil Inductive Link through a Case Study for NICU Applications

This paper outlines a design approach for biomedical wireless power transfer systems with a focus on three-coil inductive links for neonatal intensive care unit applications. The relevant literature has been explored to support the design approach, equations, simulation results, and the process of experimental analysis. The paper begins with a brief overview of various power amplifier classes, followed by an in-depth examination of the most common power amplifiers used in biomedical wireless power transfer systems. Among the traditional linear and switching amplifier classes, class-D and class-E switching amplifiers are highlighted for their enhanced efficiency and straightforward implementation in biomedical contexts. The impact of load variation on these systems is also discussed. This paper then explores the basic concepts and essential equations governing inductive links, comparing two-coil and multi-coil configurations. In the following, the paper discusses foundational coil parameters and provides theoretical and experimental analysis of both two-coil and multi-coil inductive links through step-by-step measurement techniques using lab equipment and addressing the relevant challenges. Finally, a case study for neonatal intensive care unit applications is presented, showcasing a wireless power transfer system operating at 13.56 MHz for powering a wearable device on a patient lying on a mattress. An inductive link with a transmitter coil embedded in a mattress is designed to supply power to a load at distances ranging from 4 cm to 12 cm, simulating the mattress-to-chest distance of an infant. the experimental results of a three-coil inductive link equipped with a Class-E power amplifier are reported, demonstrating power transfer efficiency ranging from 75% to 25% and power delivery to a 500 Ω-load varying from 340 mW to 25 mW over various distances.

Relation semantic fusion in subgraph for inductive link prediction in knowledge graphs

Inductive link prediction (ILP) in knowledge graphs (KGs) aims to predict missing links between entities that were not seen during the training phase. Recent some subgraph-based methods have shown some advancements, but they all overlook the relational semantics between entities during subgraph extraction. To overcome this limitation, we introduce a novel inductive link prediction model named SASILP (Structure and Semantic Inductive Link Prediction), which comprehensively incorporates relational semantics in both subgraph extraction and node initialization processes. The model employs a random walk strategy to calculate the structural scores of neighboring nodes and utilizes an enhanced graph attention network to determine their semantic scores. By integrating both structural and semantic scores, SASILP strategically selects key nodes to form a subgraph. Furthermore, the subgraph is initialized with a node initialization technique that integrates information about neighboring relations. The experiments conducted on benchmark datasets demonstrate that SASILP outperforms state-of-the-art methods on inductive link prediction tasks, and verify the effectiveness of our approach.

Meta-collaboration-based semantic contrast for inductive knowledge representation learning

Inductive knowledge representation learning aims at effectively representing new entities in emerging knowledge graphs based on current ones, providing positive support for reasoning facts with newly emerging entities. It requires a scheme that can derive the instant knowledge to generate rational representations for new entities. Recently, some approaches have been developed for it by capturing logical rules between entities, mining structural information of KGs, or learning multiple structural patterns of entities. However, there are two main challenges that they have yet to overcome. The first is the structural bias-induced semantic ambiguity, where new entities are typically represented in a manner akin to those with analogous structures, during which the identical structures are emphasized while the differences are overlooked. We refer to this as the structural bias, which will lead to the generated representations of new entities being semantically ambiguous. The second is the potential sparsity of new entities. The presence of new entities with low frequencies brings about the insufficient representations for these new entities even training a model from scratch with substantial costs. To this end, we propose a Meta-Collaboration-based Semantic Contrast (MCSC) framework with the aim of addressing both issues above. Following the current meta-task formulation scheme, we first acquire the relation-specific knowledge to produce entity representations through modeling relations as feedback. Then, a multi-layer graph neural network module is developed to aggregate sufficient neighbor information to update entity representations. In the final, a collaborative semantic contrast module is designed on both support and query sets to respectively overcome the structural bias-induced semantic ambiguity and the potential sparsity of new entities challenges. Such a meta-collaboration-based semantic contrast procedure transcends current meta-learning paradigms in inductive knowledge representation learning that fail to learn semantically discriminative entity representations. Experimental results of the inductive link prediction task on 12 benchmark datasets demonstrate the superiority of MCSC over SOTA baselines.

Extending the design space of minimized VA rating inductive wireless power transfer links operating in restricted sub-resonant frequency region with constant current output

Wireless power transfer systems are typically required to operate under varying geometrical positioning (vertical distance, misalignment) between the transmitter and receiver coils while supporting a load with non-constant characteristics. This creates the need for robust systems that can operate over a range of coupling coefficients under time-varying load. Widespread control methods utilized to support such an operation typically suffer from volt-ampere (VA) over-rating of the inductive wireless power transfer link (IWPTL) transmitter. Sub-resonant frequency control has proven to be an effective solution to this problem, attaining robust operation and minimized transmitter VA rating by utilizing operational frequency as the control variable for system output regulation under above-mentioned constraints. However, allowed operating frequency range is usually restricted in practical applications (e.g. to 79 kHz–90 kHz by SAE J2954 EV charging standard), limiting the misalignment tolerance of sub-resonant control method. Recently, extension of the classical sub-resonant control methodology was proposed in order to overcome this limitation. However, no clear guidelines were given for designing practical IWPTLs operating under extended sub-resonant control. To this end, this work bridges the gap between academical findings and practical applications by establishing generalized guidelines for designing sub-resonant controlled series-series (SS) compensated IWPTL with minimized transmitter VA rating, allowing to maximize misalignment tolerance under given operating frequency and output voltage ranges. The proposed methodology is accurately validated by simulations and experiments, demonstrate close correlation with analytical predictions. Experimental framework reveals that IWPTL operating under extended sub-resonant control methodology attains 50 % increase of tolerable coupling coefficients range compared to a classical system designed to operate under sub-resonant control under identical operating conditions while achieving nearly similar DC-to-DC efficiency.

Optimizing Power Transfer Efficiency in Biomedical Implants: A Comparative Analysis of SS and SP Inductive Link Topologies

Optimizing Power Transfer Efficiency in Biomedical Implants: A Comparative Analysis of SS and SP Inductive Link Topologies

Load shift keying communication techniques in implantable devices.

Inductive links represent a highly promising avenue for both powering and communicating medical implants. Yet they encounter challenges such as constrained communication distance and limited data rate. In Load Shift Keying (LSK), a switch in the secondary side of the inductive link can be placed in parallel with the load (Short-Circuit Technique - SCT), in series with the load (Open-Circuit Technique - OCT), or both (Dual Technique - DLT), to vary the impedance of the secondary. Hence, the impedance reflected to the primary side changes and is used to transmit information externally from the implant. Among these, DLT is a novel LSK technique proposed in this work, which becomes independent from the load on the implant side. This study compares these three methods, confronting measurements to simulations. The evaluation focused on variations in coil distance and load. The proposal is illustrated in the case of an implantable gastric stimulator, with specific constraints in secondary coil size and power requirements. The newly developed DLT consistently outshone SCT and OCT in extending the operational range of communication, registering a maximum modulation index of 0.797 and a bit error rate below 10- 7 at an operating distance of 95mm through the air. Its load-independent characteristic allowed DLT to surpass the performance of SCT and OCT, which were each advantageous under high and low loads, respectively. All these results are confirmed by a LTSpice simulation. Consequently, the communication techniques put forward in this work mark a significant progression in medical implant communications, enhancing coil-to-coil operational distance while adhering to a low carrier frequency.

A Wirelessly Powered Scattered Neural Recording Wearable System.

This paper introduces a wirelessly powered scattered neural recording wearable system that can facilitate continuous, untethered, and long-term electroencephalogram (EEG) recording. The proposed system, including 32 standalone EEG recording devices and a central controller, is incorporated in a wearable form factor. The standalone devices are sparsely distributed on the scalp, allowing for flexible placement and varying quantities to provide extensive spatial coverage and scalability. Each standalone device featuring a low-power EEG recording application-specific integrated circuit (ASIC) wirelessly receives power through a 60 MHz inductive link. The low-power ASIC design (84.6 μW) ensures sufficient wireless power reception through a small receiver (Rx) coil. The 60 MHz inductive link also serves as the data carrier for wireless communication between standalone devices and the central controller, eliminating the need for additional data antennas. All these efforts contribute to the miniaturization of standalone devices with dimensions of 12×12×5 mm3, enhancing device wearability. The central controller applies the pulse width modulation (PWM) scheme on the 60 MHz carrier, transmitting user commands at 4 Mbps to EEG recording ASICs. The ASIC employs a novel synchronized PWM demodulator to extract user commands, operating signal digitization and data transmission. The analog frontend (AFE) amplifies the EEG signal with a gain of 45 dB and applies band-pass filtering from 0.03 Hz to 400 Hz, with an input-referred noise (IRN) of 3.62 μVRMS. The amplified EEG signal is then digitized by a 10-bit successive approximation register (SAR) analog-to-digital converter (ADC) with a peak signal-to-noise and distortion ratio (SNDR) of 55.4 dB. The resulting EEG data is transmitted to an external software-defined radio (SDR) Rx through load-shift-keying (LSK) backscatter at 3.75 Mbps. The system's functionality is fully evaluated in human experiments.

An offset‐enhanced active rectifier with delay compensated active diodes for wirelessly powered biomedical implants

AbstractThis letter presents the design of a 13.56 MHz offset‐enhanced full‐wave active rectifier, tailored for wirelessly powered biomedical implants. The design incorporates digitally assisted, delay‐compensated active diodes and symmetrical bulk biasing in the rectifier core to enhance conduction time, thus improving the voltage conversion ratio (VCR) and power conversion efficiency (PCE). A delay improvement is achieved both in no‐load and high‐load conditions through an additional comparison path with an offset voltage that is higher than zero. The proposed rectifier is implemented and fabricated in a 180 nm CMOS technology with an area of 0.024 . The rectifier, tested and measured with inductive links, offers a maximum VCR of 96.4% and a maximum PCE of 89%.

Wirelessly Powered and Bi-Directional Data Communication System With Adaptive Conversion Chain for Multisite Biomedical Implants Over Single Inductive Link.

A wirelessly powered and data communication system is presented which is implemented as a full system, designed for multisite implanted biomedical applications. The system is capable of receiving wireless power and data communication for each implant separately, using inductive links with different resonance frequencies. To achieve this, dual-band coils are presented in the system. In addition, the system supports bi-directional half-duplex data communication, utilizing amplitude and load shift keying (ASK and LSK) modulation schemes over a single inductive link. The system employs a digitally assisted active rectifier and an automatic resonance tuning system, to improve the power transfer efficiency (PTE) through various coupling coefficients, while minimizing the reverse current and power dissipation. The power control unit enables closed-loop monitoring to prevent high or low power delivery, and it can detect inefficient or excessive wireless power transmission or prevent temperature elevation by limiting the voltage to a safe level. A new structure of self-sampling separated- Vb ASK demodulator is proposed in the paper which is utilized within the data conversion chain, serving both the external and implanted units. The whole system is fabricated using a standard 180-nm 1.8/3.3 V CMOS process with a core area of 0.82 mm[Formula: see text]. The system is tested with coupled multisite inductive links and offers the maximum overall PTE of 31.2%, from the Tx coil to the implant load.

A Frequency-Switching Inductive Power Transfer System for Wireless, Miniaturised and Large-Scale Neural Interfaces.

Three-coil inductive power transfer is the state-of-the-art solution to power multiple miniaturised neural implants. However, the maximum delivered power is limited by the efficiency of the powering link and safety constrains. Here we propose a frequency-switching inductive link, where the passive resonator normally used in a three-coil link is replaced by an active resonator. It receives power from the external transmitter via a two-coil inductive link at the low frequency of 13.56 MHz. Then, it switches the operating frequency to the higher frequency of 433.92 MHz through a dedicated circuitry. Last, it transmits power to 1024 miniaturised implants via a three-coil inductive link using an array of 37 focusing resonators for a brain coverage of 163.84 mm 2. Our simulations reported a power transfer efficiency of 0.013 % and a maximum power delivered to the load of 1970 μW under safety-constrains, which are respectively two orders of magnitude and more than six decades higher compared to an equivalent passive three-coil link. The frequency-switching inductive system is a scalable and highly versatile solution for wireless, miniaturised and large-scale neural interfaces.

A wireless-power and data-transfer using inductive RF link and ASK modulation

This paper aims to present a novel trans-cutanaeous, wireless and an efficient radio frequency (RF) inductive power and data link (IPDL) based on amplitude shift key (ASK) - modulator with an efficient ‘Class-E’– RF ‘power amplifier’ that is applicable to implantable medical devices (IMDs). The IPDL system comprises an external device placed on exterior to human skin to transmitting power and data to IMDs like implantable micro-systems (cardiac pacemakers, cochlear implants, retinal implants, deep brain stimulators) to excite and monitor respective neural and muscular system. The entire system is designed to operate with a ‘low-band-frequency’ of 4 MHz by avoiding the problem of tissue heating. A practical model for the IPDL with results is presented. Various graphs such as frequency vs primary coil/secondary coil output are plotted and shown. Typical specifications of the exterior device, namely, the modulation-index (MI) and the modulation-rate (MR) are 40% and 4.3% respectively with a data rate of 172 Kbps. The design is simulated with electronic workbench MULTISIM 12.0 and TINA Ver 9.

A Wearable Real-Time System for Simultaneous Wireless Power and Data Transmission to Cortical Visual Prosthesis.

Wireless, miniaturised and distributed neural interfaces are emerging neurotechnologies. Although extensive research efforts contribute to their technological advancement, the need for real-time systems enabling simultaneous wireless information and power transfer toward distributed neural implants remains crucial. Here we present a complete wearable system including a software for real-time image capturing, processing and digital data transfer; an hardware for high radiofrequency generation and modulation via amplitude shift keying; and a 3-coil inductive link adapt to operate with multiple miniaturised receivers. The system operates in real-time with a maximum frame rate of 20 Hz, reconstructing each frame with a matrix of 32 × 32 pixels. The device generates a carrier frequency of 433.92 MHz. It transmits the highest power of 32 dBm with a data rate of 6 Mbps and a variable modulation index as low as 8 %, thus potentially enabling wireless communication with 1024 miniaturised and distributed intracortical microstimulators. The system is primarily conceived as an external wearable device for distributed cortical visual prosthesis covering a visual field of 20 °. At the same time, it is modular and versatile, being suitable for multiple applications requiring simultaneous wireless information and power transfer to large-scale neural interfaces.

Planar antenna design for contactless energizing applications: resonance analysis

Advances in medical technology suggest that the application of implantable medical devices or Smart Hospital Devices (SHD) can enhance the control and treatment of chronic disorders. However, most of these developments require an electrical power source for operation, making the use of batteries unfeasible. This paper presents the design and resonance analysis of four different geometries for the fabrication of planar antennas as an alternative to a contactless power supply. Previously published software [19] was used to calculate the electrical parameters for each coil design. Operating trials were executed under laboratory conditions, and a bracket manufactured using polylactic acid (PLA) through a 3D printer was used to accurately define the distances between coils to achieve correct alignment between them. Based on the experimental results, it was possible to calculate the resonant frequency of the inductive links at a 5 mm spacing. Similarly, it is possible to calculate the capacitive effect necessary to improve the resonant circuit in different transmitter-receiver planar antenna pairs. The most efficient combination to induce voltage in these links is to use the hexagonal profile design as a transmitter and receiver antenna, applying a sinusoidal signal with 8 MHz frequency.

Passive Biotelemetric Detection of Tibial Debonding in Wireless Battery-Free Smart Knee Implants.

Aseptic loosening is the dominant failure mechanism in contemporary knee replacement surgery, but diagnostic techniques are poorly sensitive to the early stages of loosening and poorly specific in delineating aseptic cases from infections. Smart implants have been proposed as a solution, but incorporating components for sensing, powering, processing, and communication increases device cost, size, and risk; hence, minimising onboard instrumentation is desirable. In this study, two wireless, battery-free smart implants were developed that used passive biotelemetry to measure fixation at the implant-cement interface of the tibial components. The sensing system comprised of a piezoelectric transducer and coil, with the transducer affixed to the superior surface of the tibial trays of both partial (PKR) and total knee replacement (TKR) systems. Fixation was measured via pulse-echo responses elicited via a three-coil inductive link. The instrumented systems could detect loss of fixation when the implants were partially debonded (+7.1% PKA, +32.6% TKA, both p < 0.001) and fully debonded in situ (+6.3% PKA, +32.5% TKA, both p < 0.001). Measurements were robust to variations in positioning of the external reader, soft tissue, and the femoral component. With low cost and small form factor, the smart implant concept could be adopted for clinical use, particularly for generating an understanding of uncertain aseptic loosening mechanisms.

Extending the lower bound of attainable load-independent voltage gain values range in contactless, feedbackless and sensorless power delivery links

It is well-known that series(capacitive)-series(capacitive) compensated inductive wireless power transfer links (SS(CC)-IWPTL) operating at fixed frequency with constant coupling coefficient may be designed to attain arbitrary load independent voltage gain (LIVG) value, residing within a region defined only by loosely coupled transformer (LCT) parameters. Such a characteristic allows designing the system to be sensorless and operate without feedback, which is an extremely useful feature in hostile environment applications. Unfortunately, LCT parameters are not selected arbitrarily in practice; hence, the desired LIVG value may reside outside the attainable region, calling for an additional power conversion stage. In particular, region of attainable LIVG values is especially narrow when LCT inductances ratio is imposed by the application and thus cannot be freely selected. One of existing challenges is regulating the system output to low DC voltage while it is being fed from a much higher valued voltage source, i.e. calling for an extremely low LIVG value. The paper demonstrates that adopting an inductor rather than a capacitor as primary series compensation element allows to extend the lower bound of attainable LIVG values region for given LCT and operating frequency, potentially eliminating the need for an additional step-down power converter. Resulting coil-to-coil efficiency is quantified and guidelines for sizing corresponding compensation elements pair are established as well. Simulations and experiments accurately verify the proposed methodology.

High-Performance Wireless Power and Data Transmission System for Medical Implant Devices Using ASK Modulation

Wireless power and data transmission (WPDT) solutions for medical implants are highly desired. However, achieving a high-power transmission efficiency and data rate simultaneously over an inductive link remains a significant challenge. This paper presents an innovative WPDT circuit that incorporates additional MOSFETs with an inductor in a Class-E power amplifier (PA), achieving amplitude-shift keying (ASK) modulation to address this issue. Firstly, the efficiency of the inductive power transmission link and Class-E PA was analyzed, providing design insights. Then, leveraging the insights, the proposed circuit was designed in such a way that it could effectively switch between two load networks to maintain high transfer efficiency for ASK modulation. Based on the load networks, the relationship between introducing the inductor’s value and the data modulation index (MI) was derived to help achieve the desired high-power transmission efficiency. Additionally, the design and calculation of the proposed circuit are also presented. Finally, the proposed circuit was validated through simulations and experiments, demonstrating a power delivery to a load of 84.1 mW with a power transmission efficiency of 70.8% at a data rate and carrier frequency of 3 Mbps and 16 MHz, respectively. Furthermore, the bit error rate (BER) is less than 10−6 with an MI of 10%.

An ultra‐low‐power CWM/SCM demodulator for inductive‐powered IMDs with the DRCF ratio of 50% and the powering index of 75%

SummaryIn this paper, an ultra‐low‐power and area‐efficient demodulator circuit for wireless downlink SCM/CWM modulation schemes is proposed. The proposed demodulator offers high performances and allows simultaneous power and downlink data transmission over a single 13.56‐MHz inductive link. The proposed method requires only two carrier cycles per data bit period, and also, a power index of 75% is obtained. Although the proposed demodulator can be applicable to other wireless systems, here, it is intended for implantable medical devices. To prove the performance of the proposed demodulator circuit, it has been designed and post‐layout simulations are provided using a standard 65‐nm CMOS technology and occupies 27 × 32 μm2 of active area. Post‐layout simulation results indicate that with a 1‐V power supply, the proposed circuit achieves an ultra‐low‐power consumption of 8.51 μW at a data rate of 6.78 Mb/s corresponding to an energy efficiency of 1.25 pJ/bit.

Simultaneous Wireless Power and Data Transfer in Different Applications

In Modern Era, the demand for wireless technology has surged exponentially, promising enhanced living comfort and safety. Simultaneous Wireless Power and Data Transfer (SWPDT) has emerged as a critical area of study, finding applications in electric vehicles, underwater autonomous vehicles, and biomedical implants. This technology facilitates real-time monitoring while supplying power, eliminating the need for bulky cables and conventional power sources. Hence this paper addresses the state-of-art of SWPDT in different applications This comprehensive review covers various SWPDT implementation methods for applications like electric vehicles, biomedical implants, and autonomous underwater vehicles. Different techniques for implementation of SWPDT using inductive links and its design recommendations.

A Wireless Multimodal Physiological Monitoring ASIC for Animal Health Monitoring Injectable Devices.

Utilizing injectable devices for monitoring animal health offers several advantages over traditional wearable devices, including improved signal-to-noise ratio (SNR) and enhanced immunity to motion artifacts. We present a wireless application-specific integrated circuit (ASIC) for injectable devices. The ASIC has multiple physiological sensing modalities including body temperature monitoring, electrocardiography (ECG), and photoplethysmography (PPG). The ASIC fabricated using the CMOS 180 nm process is sized to fit into an injectable microchip implant. The ASIC features a low-power design, drawing an average DC power of 155.3 µW, enabling the ASIC to be wirelessly powered through an inductive link. To capture the ECG signal, we designed the ECG analog frontend (AFE) with 0.3 Hz low cut-off frequency and 45-79 dB adjustable midband gain. To measure PPG, we employ an energy-efficient and safe switched-capacitor-based (SC) light emitting diode (LED) driver to illuminate an LED with milliampere-level current pulses. A SC integrator-based AFE converts the current of photodiode with a programmable transimpedance gain. A resistor-based Wheatstone Bridge (WhB) temperature sensor followed by an instrumentation amplifier (IA) provides 27-47 °C sensing range with 0.02 °C inaccuracy. Recorded physiological signals are sequentially sampled and quantized by a 10-bit analog-to-digital converter (ADC) with the successive approximation register (SAR) architecture. The SAR ADC features an energy-efficient switching scheme and achieves a 57.5 dB signal-to-noise-and-distortion ratio (SNDR) within 1 kHz bandwidth. Then, a back data telemetry transmits the baseband data via a backscatter scheme with intermediate-frequency assistance. The ASIC's overall functionality and performance has been evaluated through an invivo experiment.