Increasing Filtration Efficiency Research Articles

Microstructure and Pore Characteristics of a Double-Layered Pore Structure Powder Filter Fabricated by the WPS Process

In order to supply high-purity process gas in the semiconductor manufacturing process, a gas filter is used to remove particles that may be contained in the gas. However, because the gas filters currently in use have simple pore structures, there is a need to increase filtration efficiency through the development of filters with complex pore structures. In this study, a metal powder filter with double-layered pores was manufactured using a Wet Powder Spraying process (WPS) to increase the filtering efficiency of gas filters used in semiconductor manufacturing. The effects of the mixing ratio of spherical-shape and flake-shape powders and the rolling process on the filter’s characteristics were investigated. The filter’s performance, microstructure, and surface roughness were evaluated by measuring porosity and gas permeability. The results showed that as the ratio of flake-shaped powder decreased, the thickness of the coating layer and the porosity of the filter decreased. Additionally, it was observed that as the rolling process progressed, the non-uniform pore structure was oriented parallel to the cross-section of the filter regardless of the mixing ratio. Measurements found that the gas permeability of the uncoated filter support was the highest, and that gas permeability decreased as the proportion of spherical powder increased regardless of the average particle size of the mixed powder. Lower gas permeability was observed in rolled samples. A filtration efficiency of LRV 3 or higher was confirmed.

Bacterial transport mediated by micro-nanobubbles in porous media

Determining the role of micro-nanobubbles (MNBs) in controlling the risk posed by pathogens to soil and groundwater during reclaimed water irrigation requires clarification of the mechanism of how MNBs block pathogenic bacteria. In this study, real-time bioluminescence imaging was used to investigate the effects of MNBs on the transport and spatiotemporal distribution of bioluminescent Escherichia coli 652T7 strain in porous media. The presence of MNBs significantly increased the retention of bacteria in the porous media, decreasing the maximum relative effluent concentration (C/C0) by 78 % from 0.97 (without MNBs) to 0.21 (with MNBs). The results suggested that MNBs provided additional sites at the air-water interface (AWI) for bacterial attachment and acted as physical obstacles to reduce bacterial passage. These effects varied with environmental conditions such as solution ionic strength and pore water velocity. The results indicated that MNBs enhanced electrostatic attachment of bacteria at the AWI and their mechanical straining in pores. This study suggests that adding MNBs in pathogen-containing water is an effective measure for increasing filtration efficiency and reducing the risk of pathogenic contamination during agricultural irrigation.

Lumped model for evaluating dynamic filtration and pressure drop behaviour in diesel particulate filters

Particulate matter (PM) emitted from diesel vehicles poses significant risks to the global climate, environment, and human health. Diesel particulate filters (DPF) are currently the only effective aftertreatment device for PM emissions reduction, and it is important to reflect the DPF filtration and pressure drop performance by numerical method. This study established and validated a lumped model based on the spherical packed bed theory and Darcy’s law. The model described the dynamic PM filtration process in DPF, predicting real-time characteristics such as wall porosity, soot load, and pressure drop with improved accuracy. The effects of channel characteristics, monolithic size, and exhaust conditions on filtration and pressure drop performance were also investigated. The results showed that an increase in cell density, wall thickness, DPF length, and diameter is beneficial for increasing filtration efficiency, while DPF inlet temperature and exhaust mass flow rate have adverse effects. Besides, wall thickness, DPF diameter and exhaust flow rate have a more significant impact on total pressure drop. The results improve the dynamic performance prediction in the PM filtration process and provide a theoretical basis for DPF structural optimization.

The impact of heating, ventilation, and air conditioning design features on the transmission of viruses, including the 2019 novel coronavirus: A systematic review of filtration.

Historically, viruses have demonstrated airborne transmission. Emerging evidence suggests the novel coronavirus (SARS-CoV-2) that causes COVID-19 also spreads by airborne transmission. This is more likely in indoor environments, particularly with poor ventilation. In the context of airborne transmission, a vital mitigation strategy for the built environment is heating, ventilation, and air conditioning (HVAC) systems. HVAC features could modify virus transmission potential. A systematic review was conducted to identify and synthesize research examining the effectiveness of filters within HVAC systems in reducing virus transmission. A comprehensive search of OVID MEDLINE, Compendex, and Web of Science Core was conducted to January 2021. Two authors were involved in study selection, data extraction, and risk of bias assessments. Study characteristics and results were displayed in evidence tables and findings were synthesized narratively. Twenty-three relevant studies showed that: filtration was associated with decreased transmission; filters removed viruses from the air; increasing filter efficiency (efficiency of particle removal) was associated with decreased transmission, decreased infection risk, and increased viral filtration efficiency (efficiency of virus removal); increasing filter efficiency above MERV 13 was associated with limited benefit in further reduction of virus concentration and infection risk; and filters with the same efficiency rating from different companies showed variable performance. Adapting HVAC systems to mitigate virus transmission requires a multi-factorial approach and filtration is one factor offering demonstrated potential for decreased transmission. For filtration to be effective, proper installation is required. Of note, similarly rated filters from different companies may offer different virus reduction results. While increasing filtration efficiency (i.e., increasing MERV rating or moving from MERV to HEPA) is associated with virus mitigation, there are diminishing returns for filters rated MERV 13 or higher. Although costs increase with filtration efficiency, they are lower than the cost of ventilation options with the equivalent reduction in transmission. Systematic review registration: PROSPERO 2020 CRD42020193968.

Electrospun nylon‐66 nanofiber coated filter media for engine air filtration applications

AbstractAir filtration plays a vital role in the performance and operations of engines, especially for heavy‐duty combat vehicles operating in the desert environment. Conventional cellulose media comprises micro‐fibers exhibiting low filtration efficiency for particles within the range of 0.1 to 0.5 μm (most penetrating particle size, MPPS). Nanofiber coating on cellulose media can increase the filtration efficiency, however, with the penalty of an increase in pressure drop. The features of nylon‐66 nanofibers, such as high mechanical strength, greater thermal stability, and high surface‐to‐volume ratio, will be beneficial for developing nano‐coated filter media. In this study, electrospun nylon‐66 nanofibers were coated over two cellulose‐based filter media and tested on an air filtration test rig that employs a suction‐type blower replicating the realistic condition of a heavy‐duty engine intake. The test rig was fabricated to evaluate the performance of the nano‐coated filter media in terms of pressure drop, filtration efficiency, and quality factor (Q‐factor). The experimental results demonstrated that the nylon‐66 nano‐coated media have higher Q‐factor (in the MPPS range) than the cellulose media due to the increased filtration efficiency compared to the rise in pressure drop. Therefore, such electrospun nylon‐66 nanofiber‐coated air filters can be an alternative to conventional cellulose media.

Nanofibers in Respiratory Masks: An Alternative to Prevent Pathogen Transmission.

Recent global outbreak of COVID-19 has raised serious awareness about our abilities to protect ourselves from hazardous pathogens and volatile organic compounds. Evidence suggests that personal protection equipment such as respiratory masks can radically decrease rates of transmission and infections due to contagious pathogens. To increase filtration efficiency without compromising breathability, application of nanofibers in production of respiratory masks have been proposed. The emergence of nanofibers in the industry has since introduced a next generation of respiratory masks that promises improved filtration efficiency and breathability via nanometric pores and thin fiber thickness. In addition, the surface of nanofibers can be functionalized and enhanced to capture specific particles. In addition to conventional techniques such as melt-blown, respiratory masks by nanofibers have provided an opportunity to prevent pathogen transmission. As the surge in global demand for respiratory masks increases, herein, we reviewed recent advancement of nanofibers as an alternative technique to be used in respiratory mask production.

Sustainable wastewater treatment by RO and hybrid organic polyamide membrane nanofiltration system for clean environment

One of the environmental pollution is happened by the discharge of industrial wastewater that needs to be adequately filtered. Given that the effluent from the leather industry contains high levels of chromium, heavy metals, lipids, and Sulphur, it is one of the wastewater disposals that are most damaging. This experimental study focuses on reverse osmosis and hybrid organic polyimide membrane for nanofiltration for sustainable wastewater treatment. In the RO and organic polyamide Nano-porous membranes, a thin film of polyamide membrane was used for efficient filtration. Taguchi analysis optimized process parameters such as pressure, temperature, pH, and volume reduction factor. The outcome shows an 89% reduction in total wastewater hardness, an 88% reduction in sulfate, and an 89% efficiency reduction in COD. As a result, the proposed technology significantly increased filtration efficiency.

Design of Water Treatment Plant on the Basis of SCADA Using Use of Coconut Shell as Capping For Sand in Rapid Sand Filters

The design of a water treatment plant utilizing SCADA (Supervisory Control and Data Acquisition) technology and coconut shell as a capping material for sand in rapid sand filters is presented in this study. The primary objective of the design is to provide safe drinking water by removing suspended solids, organic matter, and other contaminants from the raw water. The treatment process involves several stages, including coagulation, flocculation, sedimentation, rapid sand filtration, and disinfection. The use of coconut shell as a capping material for sand in rapid sand filters is a novel approach that offers several benefits over traditional sand filters, including increased filtration efficiency and reduced maintenance costs. SCADA technology is utilized to automate the operation of the treatment plant, enabling real-time monitoring and control of the treatment process. The design of the treatment plant is presented in detail, including the sizing and specification of equipment, process flow diagrams, and instrumentation and control systems. The design parameters are based on local water quality standards and are optimized to ensure maximum efficiency and effectiveness of the treatment process. Overall, the proposed design provides an efficient and cost-effective solution for water treatment, utilizing innovative technologies and materials to deliver safe drinking water to the community.

Evaluating the filtration efficiency of close-coupled catalyzed gasoline particulate filter (cGPF) over the WLTC and simulated RDE cycles.

Gasoline particulate filter (GPF) is a cost-effective solution to particle number emissions from gasoline direct injection vehicles. Filtration efficiency, as a key parameter of GPF, was usually assessed at chassis level over regulatory drive cycles. However, the promulgation of real driving emission (RDE) requirements in the EU and Chinese regulations necessitates evaluations based on non-legislative cycles to guarantee the on-road emissions are compliant to regulatory requirements. In this research, two aggressive drive cycles, RTS95 at 23degC and modified RDE at 0degC, were complemented to the WLTC to evaluate the filtration efficiency of a catalyzed GPF (cGPF) in fresh conditions to obtain the so-called "worst-case" filtration efficiency. In the WLTC, RTS95, and simulated RDE tests, the filtration efficiency of the test cGPF was 51.1%, 41.3%, and 85.1% respectively. In the simulated RDE test, the test cGPF filtrated solid particles with a diameter above 23nm and 10nm at a similar efficiency. Increased filtration efficiency with heavier soot load could offset the relatively low filtration efficiency in cold-start and warm-up durations, hence the filtration efficiency for a clean cGPF showed higher sensitivity to cycle length over driving dynamics and testing temperature. In acceleration events with cGPF mounted, the particle diameter where number concentration peaked decreased as the engine warmed up. In deceleration events, bimodal and trimodal particle number size distributions with much lower concentrations were observed.

Modification of the commercial polyester filter media support with electrospun polyethylene terephthalate fibers and its application for air purification

In this study, the electrospinning process modifies the commercial polyester filter media to increase filtration efficiency. The polyethylene terephthalate (PET) solution produces electrospun fiber on commercial polyester filter media at various rotation speeds and durations. The PET concentration and electrospinning applied voltage were adjusted accordingly to obtain bead-free electrospun fibers. As a result, the modified filter media’s filtration efficiency is approximately two times higher than the commercial polyester filter media at 300 rpm and 5 hours of electrospinning duration. Furthermore, the efficiency of the single unit modified filter media is 53.76% with an airflow resistance of 39.2 Pa and quality factor of 0.01968 Pa−1 which are comparable to the combination of two units’ air filters. Thus, replacing two units’ air filters having a primary and secondary filter with a single unit modified filter media is justifiable.

Preparation of Photocatalytic TiO2-Polyacrylonitrile Nanofibers for Filtration of Airborne Microorganisms.

Background:We aimed to investigate the efficiency of neat polyacrylonitrile (PAN) nanofibers and photocatalytic PAN/TiO2 nanofibers for removal of airborne microorganisms.Methods:Nanofibers were fabricated from 16 wt% of PAN dissolved in dimethyl formamide through the electrospinning technique. The efficiency of media for removal of Staphylococcus epidermidis and Bacillus subtilis was investigated at different conditions such as face velocity, relative humidity, air temperature and UVC radiation intensity. as face velocity (0.1 and 0.3 m/s), relative humidity (35±5% and 60±5%), air temperature (22±3 °C and 30±3 °C) and the UVC radiation intensity (dark, 1±0.09 mW/cm2 and 1.8±0.07 mW/cm2) using air sampling from upstream and downstream of media by cascade impactor containing blood agar culture medium.Results:The mean diameter of electrospun fibers and coefficient of variation were 194 nm and 15%, respectively. The amount of immobilized TiO2 on the filter was 620±6.56 mg/m2. Photocatalytic nanofiber filter media presented the best performance for removal of airborne B. subtilis at 60±5% relative humidity, 0.1 m/s face velocity, air temperature 22 °C, and 1.8 ± 0.07 mW/cm2 UVC radiation.Conclusion:The filtration efficiency of photocatalytic media was significantly higher than neat ones. Lower efficiency of media was found in the higher air velocity for all bioaerosols. High UVC radiation intensity increased filtration efficiency. Moreover, the increase in air temperature and relative humidity (except for TiO2-coated media under UVC radiation) did not significantly affect the filtration efficiency of all media.

Kontroverze u vezi sa stvarnom zaštitom od virusa SARS-Cov-2 različitim najčešće korišćenim maskama

Face masks serve to protect the respiratory system from unwanted aerosol droplets, in which various types of pathogens or pollutants are present. They are particularly important during a pandemic, like SARS-CoV-2 pandemic we are withessing. The efficiency of filtration of aerosol droplets, which contain the virus particles, is generally unsatisfactory, especially in conditions of extremely virulent environments, for the most of commercially available masks. Therefore, the challenge is to produce masks with increased filtration efficiency, in order to reduce the percentage of virus penetration through the mask. Hence, it is crucial to correctly define the possibilities and limitations of today's most commonly used epidemiological masks, in order to successfully define completely new concepts of face masks manufacturing, which would enable the most effective protection not only of medical workers but also patients, especially in areas where virus concentrations are extremely high. Also, it has been shown that, in addition to the concentrations of infectious pathogens in a given environment, the conditions in which infection with a given pathogen occurs, such as temperature and humidity within a given contaminated space, are also important.

Study of the Filtration Performance of Multilayer and Multiscale Fibrous Structures.

As the incidence of small-diameter particles in the air has increased in recent decades, the development of efficient filtration systems is both urgent and necessary. Nanotechnology, more precisely, electrospun nanofibres, has been identified as a potential solution for this issue, since it allows for the production of membranes with high rates of fibres per unit area, increasing the probability of nanoparticle collision and consequent retention. In the present study, the electrospinning technique of polyamide nanofibre production was optimized with the variation of parameters such as polymer concentration, flow rate and needle diameter. The optimized polyamide nanofibres were combined with polypropylene and polyester microfibres to construct a multilayer and multiscale system with an increased filtration efficiency. We observed that the penetration value of the multilayer system with a PA membrane in the composition, produced for 20 min in the electrospinning, is 2.7 times smaller than the penetration value of the system with the absence of micro and nano fibers.

Systematic experimental comparison of particle filtration efficiency test methods for commercial respirators and face masks

Respirators, medical masks, and barrier face coverings all filter airborne particles using similar physical principles. However, they are tested for certification using a variety of standardized test methods, creating challenges for the comparison of differently certified products. We have performed systematic experiments to quantify and understand the differences between standardized test methods for N95 respirators (NIOSH TEB-APR-STP-0059 under US 42 CFR 84), medical face masks (ASTM F2299/F2100), and COVID-19-related barrier face coverings (ASTM F3502-21). Our experiments demonstrate the role of face velocity, particle properties (mean size, size variability, electric charge, density, and shape), measurement techniques, and environmental preconditioning. The measured filtration efficiency was most sensitive to changes in face velocity and particle charge. Relative to the NIOSH method, users of the ASTM F2299/F2100 method have commonly used non-neutralized (highly charged) aerosols as well as smaller face velocities, each of which may result in approximately 10% higher measured filtration efficiencies. In the NIOSH method, environmental conditioning at elevated humidity increased filtration efficiency in some commercial samples while decreasing it in others, indicating that measurement should be performed both with and without conditioning. More generally, our results provide an experimental basis for the comparison of respirators certified under various international methods, including FFP2, KN95, P2, Korea 1st Class, and DS2.

PURIFICATION OF WATER-ALCOHOLIC MIXTURE WITH MODIFIED NATURAL MATERIALS

The aryticle presents the results of theoretical and experimental research on improving the technology of purification of water-alcohol mixture with natural modified minerals for the production of vodka. The methods and main filtering materials used in alcohol technology have been considered, the inefluence of natural efficiencies of modilification has been determined. Methods for determining physicochemical parameters, cationic-anionic composition of the sort, method of modification of natural obsidian and natural zeolite clinoptilolite are described. The paper presents the main unit specific costs of hydrochloric acid solution for removal from the surface of ash elements and limestone inclusions, drinking water and prepared for washing material, water-alcohol mixture to establish an equilibrium strength value to prevent dilution of the sort. The influence of modified natural materials on physicochemical parameters and cationic-anionic composition of sorting before and after its purification by modified obsidian and clinoptilolite in comparison with quartz sand is shown. Achieving a positive effect of cleaning and improving the transparency of sorting in the technology of filtration with modified natural minerals. The predicted resistance to changes in the physical and chemical parameters of the sorting after its aging in critical conditions and the control sample and the array of parameter stock to the critical limit is determined. It was found that filtering the sort with modified obsidian allows to increase the shelf life by two months, modified clinoptilolite - by 4 months. Modification of natural obsidian and clinoptilodite allows for reduced specific consumption of hydrochloric acid and prepared water in preparation for the main cycle to increase filtration efficiency by 10-15% and get vodka with higher transparency by 0,1-0,2 units and improve the microcomponent composition of the finished vodka

Study on Microstructures of Complex Plant Polysaccharides Aerogels and Their Effects on Porosity

The microstructure of polysaccharide aerogels is a key factor affecting porosity, and directly determines the efficiency of its application as filter rod material. Scanning electron microscopy was used to observe the effects of different amounts of starch on the microstructure of the complex plant polysaccharide aerogels. The experimental results showed that the aerogel samples showed a complete and homogeneous three-dimensional network structure. With the increase of starch content, the pore size became smaller and the pore structure on the hole wall became smaller. After adding starch, the concentration of the system increased, that is, the solute in the unit volume increased, the moisture content decreased, and the air replaced the water in the gel after freeze drying, resulting in the increase of the density of the aerogel and the decrease of porosity. All aerogels showed a trend of increasing filtration efficiency with increasing particle size. The filtration performance of aerogels with different starch content was tested by using the comprehensive performance test bed of filter media. The test results showed that the capture of filter material was mainly through inertial collision. When the particle size was bigger, the greater the inertia, the greater the possibility of particle contamination being captured, so the higher the filtration efficiency.

Experimental Study of Filtration Materials Used in the Car Air Intake.

Traditional cellulose filter media used for air filtration in vehicle engines are characterized by 99.9% filtration efficiency and accuracy above 2–5 µm. The highest engine component wear is caused by dust grains above 1 µm. Filter media with nanofiber additions provide greater filtration efficiency of dust grains below 5 µm. Filter material selection for vehicle engine air filter is a problem because their manufacturers mainly provide only the structure parameters: pore size, air permeability, and thickness. There is no information about material filtration properties using polydisperse test dust. The manuscript presents methodology and experimental test results of five samples A, B, C, D and E, filter materials differing in their chemical composition and structure parameters. In the first stage, efficiency characteristics φw, filtration accuracy dzmax and the flow resistance Δpw depending on the dust absorption coefficient km of three filter cartridges of each material, A, B, C, D and E, were determined. Then, from each material characteristics of one piece was selected in order to compare their initial and initial period efficiencies as well as changes in the flow resistance depending on the dust absorption coefficient km. Obtained results showed that the filter materials differ significantly in efficiency and accuracy values in the initial filtration period. Initial period duration is also different, i.e., filtration efficiency increasing time to a certain value, which for materials with a nanofiber layer is much shorter, which minimizes engine component wear. For materials with nanofibers, flow resistance increase intensity is greater, which results from surface filtration. Filtration efficiency of each filter material sample A, B, C, D and E was assessed with the filtration quality coefficient including the efficiency and flow resistance. In the available literature, the problem of increasing filtration efficiency in the initial period is known, but there are no results for specific filter materials. Research shows that filter material characteristics are closely related. Each increase in efficiency and accuracy of intake air filtration reduces engine components wear, but it is related to flow resistance increase in the engine intake system, which reduces its power, and increases need for more frequent filter servicing.

Material Suitability Testing for Nonmedical Grade Community Face Masks to Decrease Viral Transmission During a Pandemic

Cloth face covering has been recommended by the Centers for Disease Control and Prevention to decrease community viral transmission. This study aims to determine the filtration efficiency and airflow resistance of common household materials available for homemade mask production by comparing numbers of fabrics, various layers, and manipulation. Common household woven, knitted, and nonwoven fabrics were tested for filtration efficiency using a fit testing setup and airflow resistance with pressure gauge setup. Three different levels of layering (1, 2, and 4) were tested. Some fabric material was further tested after washing and drying. Filtration performance, the area under the fitted curve comparing airflow resistance and filtration efficiency, was calculated for each fabric material and compared. Layering increased filtration efficiency and airflow resistance (P < 0.0001 and P < 0.01, respectively). Polyester felt demonstrated the highest filtration performance index (P < 0.0001), higher than all tested 100% cotton materials (all P < 0.05) as well as surgical masks (P < 0.05). Washing plus drying did not alter filtration performance significantly (P > 0.05). A filtration performance of common household fabrics were compared. Homemade mask designers and producers will have improved data to better balance effectiveness, availability, and comfort with the goal of decreasing community viral transmission.

Enhanced nano-aerosol loading performance of multilayer PVDF nanofiber electret filters

Aerosol loading behavior of PVDF nanofiber electret filters using neutrally charged nano- and submicron aerosols was investigated experimentally for the first time. The loading behavior include variations of filtration efficiency and pressure drop and distribution of deposited aerosols in the filters all having the same fiber basis weight (3.060 gsm). Through the filtration efficiency variations of uncharged/charged, single-/multi-layer filters with aerosol loading, it was observed that mechanical PVDF filters had continuously increasing filtration efficiency, while PVDF electret filters had initially decreasing and subsequently increasing filtration efficiency until reaching 100% due to diminishing electrostatic effect and enhancing mechanical effect.By combining the pressure drop evolution of different filters during aerosol loading and detailed SEM images of the loaded filters, we have demonstrated that multilayer PVDF filters, especially the electret ones, could significantly slow down the pace of filter clogging (skin effect) and increase significantly the aerosol holding capacity during depth filtration. Generally, the multilayer nanofiber filters received the most aerosol deposit during depth filtration, whereas the single-layer nanofiber filters with the same basis weight of fibers received the most deposit during cake filtration. The multilayer nanofiber filters had approximately 70% aerosol deposit in the filter during depth filtration fully utilizing the full filter thickness, especially for the electret filters that had charged fibers, and only 30% deposit in the cake. On the contrary, the single-layer uncharged/charged nanofiber filters were exactly the reverse due to persistency of the skin effect with only 30% deposit in the filter mostly located in the upstream layer, yet 70% deposit in the cake. During depth filtration, the pressure drop per added mass deposit for the multilayer electret filter was very low at 11 Pa gsm−1, which was at least twice below any other nanofiber filters. This was all attributed to the uniform capture of aerosols by electrostatic effect across the entire filter depth from the upstream to downstream layers of the multilayer electret filter. The above conclusion was confirmed by the detailed SEM images taken across the different filter layers for the multilayer filter configuration. The 4-layer electret nanofiber filter with a 3.060-gsm basis weight has 4 times more aerosol holding capacity than the single uncharged/charged nanofiber filter with the same fiber basis weight in depth filtration. Based on the standpoint of highest efficiency and capacity with maximum pressure drop 800 Pa imposed on the filtration operation, the 4-layer nanofiber electret was the best among all 4 filters. It had 52% more aerosol holding capacity than the single layer uncharged nanofiber filter and 38% more capacity than the charged single-layer and the uncharged multilayer nanofiber filters. The multilayer PVDF electret filters have excellent filtration performance for long-term aerosol filtration and also great potential applications in the fields of personal health care and environmental protection.

The comparison between vibration and aeration on the membrane performance in algae harvesting

Membrane fouling is a main problem in algae harvesting and retarding membrane fouling is significant to increase filtration efficiency and reduce harvesting cost. The aeration membrane system could mitigate membrane fouling by the coarse bubbles and the vibration membrane system could produce high shear by the vibration of membrane to mitigate fouling. In the critical flux experiment, the aeration membrane had a low critical flux of 34 L/(m2h) compared with the vibration membrane (49 L/(m2h)). After experiencing 12-h continuous filtration, the flux decline rates of vibration and aeration membrane were 3.6% and 46%, respectively. Based on the Extended Derjaguin–Landau–Verwey–Overbeek (XDLVO) theory, the free energy of fouled vibration and aeration membranes were −53.76 and −62.51 mJ/m2, respectively, indicating that vibration could better reduce the interaction of algae cells and membrane, compared with aeration. Moreover, vibration also had a better effect on the rejection of extracellular organic matter (EOM), which could reduce secondary pollution of the water body. The different working mechanism of vibration and aeration acting on membrane was draw, suggesting that the fluid velocity induced by vibration mainly acting on membrane surface could decrease membrane fouling, while the fluid velocity induced by aeration basically could not act on membrane.