Increase In Resistance Research Articles

Failure of Lithium-Ion Batteries Accelerated by Gravity.

The safety concerns surrounding lithium-ion batteries (LIBs) have garnered increasing attention due to their potential to endanger lives and incur significant financial losses. However, the origins of battery failures are diverse, presenting significant challenges in developing safety measures to mitigate accidental catastrophes. In this study, the aging mechanism of LiNi0.5Co0.2Mn0.3O2||graphite-based cylindrical 18,650 LIBs stored at room temperature for two years was investigated. It was found that an uneven distribution of electrolytes can be caused by gravity, leading to temperature variations within the battery. Specifically, it was observed that the temperature at the top of the battery was approximately -0.89 °C higher than at the bottom, correlating with an increase in partial internal resistance. Additionally, upon disassembly and analysis of spent batteries, the most significant damage to electrode materials at the top of the battery was observed. These findings suggest that gravity-induced electrolyte insufficiency exacerbates side reactions, particularly at the top of the battery. This study offers a unique perspective on the safety concerns associated with high-energy-density batteries in long-term and large-scale applications.

Differential Resistance to Acetyl-CoA Carboxylase Inhibitors in Rice: Insights from Two Distinct Target-Site Mutations.

Weeds present a significant challenge to agricultural productivity, and acetyl-CoA carboxylase (ACCase)-inhibiting herbicides have proven to be effective in managing weed populations in rice fields. To develop ACCase-inhibiting herbicide-resistant rice, we generated mutants of rice ACCase (OsACC) featuring Ile-1792-Leu or Gly-2107-Ser substitutions through ethyl methyl sulfonate (EMS) mutagenesis. The Ile-1792-Leu mutant displayed cross-resistance to aryloxyphenoxypropionate (APP) and phenylpyrazoline (DEN) herbicides, whereas the Gly-2107-Ser mutants primarily exhibited cross-resistance to APP herbicides with diminished resistance to the DEN herbicide. In vitro assays of the OsACC activity revealed an increase in resistance to haloxyfop and quizalofop, ranging from 4.84- to 29-fold in the mutants compared to that in wild-type. Structural modeling revealed that both mutations likely reduce the binding affinity between OsACC and ACCase inhibitors, thereby imparting resistance. This study offers insights into two target-site mutations, contributing to the breeding of herbicide-resistant rice and presenting alternative weed management strategies in rice cultivation.

Constraint on boric acid resistance and tolerance evolvability in Candida albicans.

Boric acid is a broad-spectrum antimicrobial used to treat vulvovaginal candidiasis when patients relapse on the primary azole drug fluconazole. Candida albicans is the most common cause of vulvovaginal candidiasis, colloquially referred to as a "vaginal yeast infection". Little is known about the propensity of C. albicans to develop BA resistance or tolerance (the ability of a subpopulation to grow slowly in high levels of drug). We evolved 96 replicates from eight diverse C. albicans strains to increasing BA concentrations to test the evolvability of BA resistance and tolerance. Replicate growth was individually assessed daily, with replicates passaged when they had reached an optical density consistent with exponential growth. Many replicates went extinct quickly. Although some replicates could grow in much higher levels of BA than the ancestral strains, evolved populations isolated from the highest terminal BA levels (after 11 weeks of passages) surprisingly showed only modest growth improvements and only at low levels of BA. No large increases in resistance or tolerance were observed in the evolved replicates. Overall, our findings illustrate that there may be evolutionary constraints limiting the emergence of BA resistance and tolerance, which could explain why it remains an effective treatment for recurrent yeast infections.

GPR56, an Adhesion GPCR with Multiple Roles in Human Diseases, Current Status and Future Perspective.

Human G protein-coupled receptor 56 (GPR56) belongs to a member of the adhesion G-protein coupled receptor (aGPCR) family and widely exists in the central nervous system and various types of tumor tissues. Recent studies have shown that abnormal expression or dysfunction of GPR56 is closely associated with many physiological and pathological processes, including brain development, neuropsychiatric disorders, cardiovascular diseases and cancer progression. In addition, GPR56 has been proven to enhance the susceptibility of some antipsychotics and anticarcinogens in response to the treatment of neuropsychological diseases and cancer. Although there have been some reports about the functions of GPR56, the underlying mechanisms implicated in these diseases have not been clarified thoroughly, especially in depression and epilepsy. Therefore, in this review, we described the molecular structure and signal transduction pathway of GPR56 and carried out a comprehensive summary of GPR56's function in the development of psychiatric disorders and cancer. Our review showed that GPR56 deficiency led to depressive-like behaviors and an increase in resistance to antipsychotic treatment. In contrast, the upregulation of GPR56 contributed to tumor cell proliferation and metastasis in malignant diseases such as glioblastoma, colorectal cancer, and ovarian cancer. Moreover, we elucidated specific signaling pathways downstream of GPR56 related to the pathogenesis of these diseases. In summary, our review provides compelling arguments for an attractive therapeutic target of GPR56 in improving the therapeutic efficiency for patients suffering from psychiatric disorders and cancer.

Simulation investigation of effects of substrate and thermal boundary resistance on performances of AlGaN/GaN HEMTs

Abstract The temperature distributions and thermal resistances of the GaN HEMTs fabricated on different substrates (sapphire, Si, SiC and diamond) with Mo/Au interlayers were calculated and analyzed by numerical simulation. The results show that the GaN HEMT on the diamond substrate exhibits the lowest channel temperature and thermal resistance, and the thermal resistance rises with the increase of the thermal boundary resistance (TBR) for all the GaN HEMTs with the different substrate materials. Meanwhile, the high TBR (2 × 10−7 m2·K/W) severely hinders the heat exchange between the GaN layer and the substrate, which makes it difficult for the heat flux to pass through the barrier. Even diamond with high thermal conductivity can hardly reduce the channel temperature of the device. Therefore, TBR must be reduced so that the heat flux can be dissipated through a high thermal conductivity substrate. In addition, the Mo/Au interlayer generates a lower thermal boundary resistance, which has little effect on the channel temperature, thermal resistance and interfacial temperature discontinuity of GaN HEMTs.

High temperature stability of regrown and alloyed Ohmic contacts to AlGaN/GaN heterostructure up to 500 °C

This Letter reports the stability of regrown and alloyed Ohmic contacts to AlGaN/GaN-on-Si high electron mobility transistors (HEMTs) for high temperature applications up to 500 °C. Transfer length method (TLM) measurements from 25 to 500 °C in air show that the regrown contacts appear to be stable up to 500 °C during short term (approximately 1 h) testing, while alloyed contacts appear to decrease in contact resistance from 300 to 500 °C though increases in the error bounds due to increase sheet resistance make it difficult to conclude definitely. Additionally, longer term testing shows both technologies remain stable at least up to 48 h at 500 °C, after which the large increase in sheet resistance makes the measurement uncertainty too large to conclude definitively. Advanced microscopy images indicate both the regrown and alloyed contact regions remain structurally intact after prolonged high temperature exposure with no visible degradation in crystallinity or metal composition.

Formulating Interfacial Impedances for Designing High-Energy and High-Power All-Solid-State Battery Cathodes.

All-solid-state batteries (ASSBs) are safe, high-energy-storage systems. However, despite the progress achieved in the development of high-ionic-conductivity solid electrolytes (SEs), the power performance of ASSBs remains low because of the high interfacial impedances in composite cathodes. Therefore, understanding the interfacial factors is crucial for obtaining high power ASSBs. This study provides a quantitative analysis of the influence of these factors using impedance spectroscopy measurements, which enables the elucidation of the interfacial impedance values of two key parameters, the grain-boundary resistance (ri,gb) and charge-transfer resistance (ri/e). Systematic investigation revealed an unexpected increase in the cathodic resistance with the decrease in the size of the cathode active material (CAM) particles, indicating that even high-reaction-surface-area CAMs yield low ri/e but high ri,gb values owing to their high porosity, resulting in a trade-off relationship. In contrast, this phenomenon is unlikely to occur in liquid-electrolyte-based batteries. Notably, we discuss how composite cathode design impacts performances of stable, high-power, and high-energy ASSBs.

Consensus on the procedure of balloon pulmonary angioplasty for chronic thromboembolic pulmonary hypertension

Chronic thromboembolic pulmonary hypertension (CTEPH) is classified as group IV pulmonary hypertension, characterized by thrombotic occlusion of the pulmonary arteries leading to vascular stenosis or obstruction, progressive increase in pulmonary vascular resistance and pulmonary arterial pressure, and eventual right heart failure. Unlike other types of pulmonary hypertension, the prognosis of CTEPH can be significantly improved by surgery, vascular intervention, and/or targeted drug therapy. Pulmonary endarterectomy (PEA) is the preferred treatment of choice for CTEPH. However, PEA is an invasive procedure with high operative risks, and is currently only performed in a few centers in China. Balloon pulmonary angioplasty (BPA) is an emerging interventional technique for CTEPH, serving as an alternative for patients who are ineligible for PEA or with residual pulmonary hypertension after PEA. BPA is gaining traction in China, but its widespread adoption is limited due to its complexity, operator skills, and equipment requirements, a lack of standard operating procedures and technical guidance, which limit the further improvement and development of BPA in China. To address this, a multidisciplinary panel of experts was convened to develop the Consensus on the Procedure of Balloon Pulmonary Angioplasty for the Chronic Thromboembolic Pulmonary Hypertension, which fomulates guidelines on BPA procedural qualification, perioperative management, procedural planning, technical approach, and complication prevention, with the aim of providing recommendations and clinical guidance for BPA treatment in CTEPH and standardizing its clinical application in this setting. Summary of recommendations: Recommendation 1: It is recommended that physicians who specialize in pulmonary vascular diseases take the lead in formulating the diagnostic and treatment plans for CTEPH, using a multidisciplinary approach.Recommendation 2: Training in BPA technique is critical; novice operators should undergo standardized operative training with at least 50 procedures under the guidance of experienced physicians before embarking on independent BPA procedures.Recommendation 3: BPA requires catheterization labs, angiography systems, standard vascular interventional devices and consumables, drugs, and emergency equipment.Recommendation 4: Patient selection for BPA should consider cardiac and pulmonary function, coagulation status, and comorbid conditions to determine indications and contraindications, thereby optimizing the timing of the procedure and improving safety.Recommendation 5: In experienced centers, patients deemed likely to benefit from early BPA, based on clinical and imaging features of CTEPH and without elevated D-dimer levels, could bypass standard 3-month anticoagulation therapy.Recommendation 6: BPA is a complex interventional treatment that requires thorough pre-operative assessment and preparation.Recommendation 7: The use of perioperative anticoagulants in BPA requires a comprehensive risk assessment of intraoperative bleeding by the operator for individualized decision making.Recommendation 8: A variety of venous access routes are available for BPA; unless contraindicated, the right femoral vein is usually preferred because of its procedural convenience and reduced radiation exposure.Recommendation 9: For the different types of vascular lesion in CTEPH, treatment of ring-like stenoses, web-like lesions, and subtotal occlusions should be prioritized before addressing complete occlusions and tortuous lesions, in order to reduce complications and improve procedural safety.Recommendation 10: A targeted, incremental balloon dilatation strategy based on vascular lesions is recommended for BPA.Recommendation 11: Intravascular pulmonary artery imaging technologies, such as OCT and IVUS can assist in accurate vessel sizing and confirmation of wire placement in the true vascular lumen. Pressure wires can be used to objectively assess the efficacy of dilatation during BPA.Recommendation 12: Endpoints for BPA treatment should be individually assessed, taking into account improvements in clinical symptoms, hemodynamics, exercise tolerance, and quality of life.Recommendation 13: Post-BPA routine monitoring of vital signs is essential; anticoagulation therapy should be initiated promptly post-procedure in the absence of complications. In cases of intraoperative hemoptysis, postoperative anticoagulation regimen adjustments should be adjusted according to the bleeding severity.Recommendation 14: If reperfusion pulmonary edema occurs during or after BPA, ensure adequate oxygenation, diuresis, and consider non-invasive positive-pressure ventilation if necessary, while severe cases may require early mechanical ventilation assistance or ECMO.Recommendation 15: In cases of intraoperative hemoptysis, temporary balloon occlusion to stop bleeding is recommended, along with protamine to neutralize heparin. Persistent bleeding may warrant the use of gelatin sponges, coil embolization, or covered stent implantation.Recommendation 16: For contrast imaging during BPA, non-ionic, low or iso-osmolar contrast agents are recommended, with hydration status determined by the patient's clinical condition, cardiac and renal function, and intraoperative contrast volume used.

Biomimetic porous wick with efficient fluid transport and excellent heat transfer for loop heat pipes

The porous wick, as a core component of the loop heat pipe (LHP), serves as a source of circulation power. Inspired by the transport system of plant vessels, a radially stacked polyethersulfone (PES) porous wick was designed using PES membranes with an anisotropic porous structure. The PES membranes exhibited excellent capillary force and high permeability. However, the supply capacity of the axially stacked wick was far inferior to that of sintered wick due to the problem of contact gaps and pore misalignment between layers. From the bionic point of view, a laminar winding special transport structure, which is perpendicular to the direction of liquid transport was proposed. The method effectively avoids the adverse effects of gap and pore misalignment on liquid transport. Combining experimental and simulation methods, the heat transfer characteristics and liquid transport characteristics of the radial stacking polyethersulfone wick (RPES) were studied and compared with those of traditional axial stacking polyethersulfone wick (APES) and sintered nickel wick. The results showed that the heat transfer performance of RPES-LHP was significantly improved, with the heating surface temperature maintained at 54.1 °C and thermal resistance of 0.095 °C/W under a heat load of 400 W, which was respectively 26.6 °C and 0.066 °C/W lower than that of the APES-LHP. The evaporator thermal resistance of RPES-LHP also ranked among the top in existing research on wicks. Simulation results indicated that the radial stacking method avoided capillary force weakening and flow resistance increase caused by gap and pore misalignment, thereby enhancing the supply capacity of RPES. The concept of regulating the stacking orientation of the wick to be perpendicular to the direction of liquid transport can strengthen the supply capacity and provide light on the design of porous wicks in the future.

Graphene oxide nanocellulose composite as a highly efficient substrate-free room temperature gas sensor

This study introduces the development of novel, flexible gas sensors operating at room temperature (RT), utilizing a graphene oxide (GO) via the modified Hummers' method and bacterial nanocellulose (BNC) composite to enhance gas detection in industrial and environmental settings. The composite materials, denoted as GO@BNC, were synthesized with varying GO concentrations ranging from 2 % to 30 %, aiming to investigate their responsiveness to gases such as carbon dioxide (CO2), oxygen (O2), acetone (Ac), and ethanol (Eth). The prepared nanomaterials were characterized using FT-IR, Raman, TGA, SEM, and AFM techniques. The bandgap of Go ranges from 4.19, 3.47, 3.16, 2.79, and 2.48 eV for 2, 5, 10, 20, and 30 % GO concentrations, respectively. Notably, the sensor containing wt % of 20 % GO concentration exhibited remarkable sensitivity to Ac, achieving a 270 % increase in resistance at a concentration of 250 μL/L. Conversely, the sensor with a wt % of 30 % GO composition showed superior sensitivity to Eth, with a 420 % signal enhancement under similar conditions. Further modification of GO@BNC through mild reduction resulted in the formation of reduced graphene oxide (rGO@BNC) composites intended to assess the functional groups' impact on sensing performance. Our findings underscore the potential of GO@BNC composites as sustainable and efficient materials for fabricating eco-friendly flexible gas sensors and devices for detecting organic compounds.

Microstructures and complex impedance analysis of spray pyrolysis-synthesized Ni doped ZnO for optoelectronic applications

This study focuses on the physical exploration, particularly examining the structural and electrical attributes of ZnO thin films produced through spray deposition, with variations in the Ni/Zn ratio (0.25 %, 0.5 %, and 0.75 %). X-ray diffraction (XRD) analysis reveals that both undoped and Ni-doped ZnO films exhibit a hexagonal crystalline structure, with a preferred orientation along the (002) direction perpendicular to the substrate. The semiconductor nature of all prepared compounds is confirmed by the grain boundary resistance. An escalation in Ni concentration corresponds to an increase in grain boundary resistance. The activation energy values, derived from both relaxation time and grain boundary resistances, closely align. Impedance studies indicate the presence of two relaxation processes within the compounds. The Nyquist diagram illustrates the emergence of semicircles, with decreasing radii at higher temperatures, indicating thermally activated semiconductor behavior in these samples, as evidenced by electrical conductance and distribution of relaxation times.

English

Background: Interest in finding efficient ways to remove penicillin allergy alerts has grown as a result of awareness of the considerable excess of false-negative diagnoses in patients with penicillin allergy labels (90%-95%), the poorer course with non–ß-lactam antibiotics, the increase in bacterial resistance, and the fact that these problems can affect up to 20% of the population in some countries. The strategies proposed have generated many publications in countries where the number of allergists to conduct such studies is low. In many cases where delabeling is performed, the risk of ß-lactam allergy is low, and a single penicillin challenge is sufficient to delabel the alert. However, other less “ultrarapid” strategies can be used to administer a ß-lactam during an admission for infection and thus postpone delabeling until traditional drug allergy consultations. However, the definitive withdrawal of ß-lactam alerts is threatened by nonremoval of alerts in electronic health records and by the reactivation or nonsynchronization of alerts between electronic systems at different levels of care. Allergy departments need to reflect on how to implement practices that enable rapid and efficient delabeling of drug allergy alerts, especially in patients with major comorbidities.

Older adults use fewer muscles to overcome perturbations during a seated locomotor task.

Locomotor perturbations provide insights into the human's response to motor errors. We investigated the differences in motor adaptation and muscle co-contraction between young and older adults during perturbed arms and legs recumbent stepping. We hypothesized that besides prolonged adaptation due to use-dependent learning, older adults would exhibit greater muscle co-contraction than young adults in response to the perturbations. Perturbations were brief increases in resistance applied during each stride at the extension-onset or mid-extension of the left or right leg. Seventeen young adults and eleven older adults completed four 10-minute perturbed stepping tasks. Subjects were instructed to follow a visual pacing cue, step smoothly, and use all their limbs to drive the stepper. Results showed that young and older adults did not decrease their errors with more perturbation experience, and errors did not wash out after perturbations were removed. Interestingly, older adults consistently had smaller motor errors than young adults in response to the perturbations. Older adults used fewer muscles to drive the stepper and had greater co-contraction than young adults. The results suggest that despite similar motor error responses, young and older adults use distinctive muscle recruitment patterns to perform the motor task. Age-related motor strategies help track motor changes across the human lifespan and are a baseline for rehabilitation and performance assessment.

Application of MgO/ZrO2 coating on 309 stainless steel to increase resistance to corrosion at high temperatures and oxidation by an electrochemical method

Abstract 309 stainless steel is one of the steels that have the highest resistance to corrosion and thermal oxidation compared to other steel grades, but it should not be used at temperatures higher than 980°C if there are temperature fluctuations. Additionally, 309 stainless steel is not designed for use in wet environments and has the least corrosion resistance. This study aims to cover 309 stainless steel with MgO/ZrO2 particles using a two-step electroplating deposition method and then sintering to increase its resistance to wet corrosion and oxidation in temperature fluctuations. The intermediate ZrO2 coating makes the outer MgO layer about two times thicker and reduces the corrosion current density. The morphology of the coatings was determined using scanning electron microscopy and X-ray diffraction, and oxidation resistance was determined using cyclic oxidation tests and the wet corrosion test of the corrosion solution. 3.5% NaCl was used. The results showed that the coated samples, due to the use of TiO2 middle layer and MgO protective layer in the electrochemical method, have a 2-fold increase in wet corrosion and an increase in hardness of about 77%, as well as an increase in oxidation resistance of 1.8% compared to the sample without coating. Also, the reason for using the electrochemical deposition method is for better surface smoothness and less porosity of the coating as well as its use on all metals compared to thermal spray methods.

Field Induced Off‐State Instability in InGaZnO Thin‐Film Transistor and its Impact on Synaptic Circuits

AbstractCharge storage synaptic circuits employing InGaZnO thin‐film transistors (IGZO TFTs) and capacitors are a promising candidate for on‐chip trainable neural network hardware accelerators. However, IGZO TFTs often exhibit bias instability. For synaptic memory applications, the programming transistors are predominantly exposed to asymmetric off‐state biases, and a unique field‐dependent on‐current reduction under off‐scenario is observed which may result in programming current variation. Further examination of the phenomenon is conducted with transmission line‐like method and degradation recovery tests, and current reduction can be attributed to contact resistance increase by charge trapping in the source and drain electrode and the channel region. The current decrease is subsequently formulated with a stretched exponential model with bias‐dependent parameters for quantitative circuit analysis under off‐state degradation. A neural network hardware acceleration simulator is utilized to assess the complicated impact the off‐state current degradation could instigate on on‐chip trainable IGZO TFT‐based synapse arrays. The simulation results generally demonstrate deteriorated training accuracy with aggravated off‐state instability, and the accuracy trend is elucidated from the perspective of weight symmetry point.

Investigating effective strategies for sustainable operation of a submerged anaerobic membrane bioreactor (SAnMBR) coupled with ceramic ultrafiltration membrane

This study presents a mechanistic approach to explore the key operational parameters governing the flux performance of an SAnMBR system coupled with a ceramic flat-sheet ultrafiltration membrane. Experiments were conducted at mixed liquor suspended solid (MLSS) concentrations of 12, 18, and 24 g/L using biogas sparging, backwashing, and a combination of both to investigate the most effective fouling mitigation strategy by exploring the fouling mechanism at a critical flux regime. To validate the experimental findings, a mathematical model was used to simulate the time-based variation of membrane effective pore radius (m), decrease in membrane porosity (%), thickness of cake layer (m), and membrane resistance (1/m). The study found that at a low biomass concentration, there was a sharp decline in the membrane pore radius leading to an increase in membrane resistance in the absence of any fouling mitigation strategies. However, by implementing these strategies individually and in combination, they maintained a higher pore radius and controlled the increase in membrane resistance even at high biomass concentrations. It was observed that biogas sparging outperformed the conventional backwashing strategy and the SAnMBR system exhibited superior performance attaining higher flux rates for prolonged duration. The advanced spectroscopic analysis confirmed the presence of a higher concentration of polysaccharides responsible for cake layer biofouling, and significant pore blocking due to inorganic foulants at high biomass concentrations. This suggests that the SAnMBR system must be operated at optimised biomass levels below the critical flux for sustained operation. Additionally, the key operational parameters identified using the mathematical model provide a precise assessment of SAnMBR performance, to improve its design efficiency for field applications.

In situ Electrical Resistance Measurement of Pure Titanium during Severe Plastic Deformation by High‐Pressure Sliding

This study presents in situ measurements of electrical resistance in pure Ti during severe plastic deformation (SPD) under high pressures. The process of high‐pressure sliding (HPS) is adopted for the SPD so that straining is feasible under various pressures covering α to ω allotropic phase transformation in pure Ti. Anvil surfaces are coated by a plasma‐sprayed alumina layer to maintain electrical insulation between the sample and the anvils during HPS operation. The electrical resistance increases continuously with straining by the HPS processing but the increase in the electrical resistance is more pronounced as the applied pressure increases, particularly when the ω phase formation occurs. The phase transformation is evidenced by X‐ray diffraction analysis as well as in situ static heating experiment. The continuous increase in the electrical resistance suggests that there is neither critical strain nor avalanche for the phase transformation to the ω phase.This article is protected by copyright. All rights reserved.

A new study on the effects of clay nanoparticles on the corrosion performance of Al-Si-Cu matrix composites in both acidic and alkaline solutions

In this paper, the influence of clay nanoparticles on the corrosion properties of the Al-Si-Cu matrix was investigated. The nanocomposite fabricating method was stir-casting when stirring times and temperatures were variables to change nanocomposite characteristics. Several corrosion tests were performed to examine the relationship between the microstructure and the degradation mechanism of various fabricated nanocomposites. Tafel polarization measurements indicated a lower corrosion rate for all nanocomposites compared to the Al-Si-Cu matrix in 0.1 M NaOH solution. The reduction range was 23.6–79.0% based on the smaller size of Si precipitates. In this situation, the interconnection of surface pores was lowest. However, electrochemical impedance spectroscopy (EIS) results showed that nanocomposite impedance would be increased up to 99.7% in comparison to the matrix without clay nanoparticles in 1 M HCl solution when the stirring temperature was 750 °C. EIS calculation also displayed that an increase (about 17.1–50.8%) in the nanocomposite resistance would be achieved when the stirring time was 2 min in 0.04 H2SO4 solution. The reason could be attributed to the larger size of Si particles since coarse precipitates were more effective agents to act as barriers for anodic dissolution of the lower layer of the Al-Si-Cu matrix when Tafel polarization tests demonstrated that the anodic reaction controlled the corrosion rate of the aluminum matrix.

The use of stem cells in the treatment of mastitis in dairy cows

Mastitis is a multifactorial inflammatory disease. The increase in antibiotic resistance of bacteria that cause mastitis means that cattle breeders would prefer to reduce the use of antibiotics. Recently, therapies using mesenchymal stem cells (MSCs) from various sources have gained significant interest in the development of regenerative medicine in humans and animals, due to their extraordinary range of properties and functions. The aim of this study was to analyze the effectiveness of an allogeneic stem cells derived from bone marrow (BMSC) and adipose tissue (ADSC) in treating mastitis in dairy cattle. The research material consisted of milk and blood samples collected from 39 Polish Holstein-Friesian cows, 36 of which were classified as having mastitis, based on cytological evaluation of their milk. The experimental group was divided into subgroups according to the method of MSC administration: intravenous, intramammary, and intravenous + intramammary, and according to the allogeneic stem cells administered: BMSC and ADSC. The research material was collected at several time intervals: before the administration of stem cells, after 24 and 72 h, and after 7 days. Blood samples were collected to assess hematological parameters and the level of pro-inflammatory cytokines, while the milk samples were used for microbiological assessment and to determine the somatic cells count (SCC). The administration of allogeneic MSCs resulted in a reduction in the total number of bacterial cells, Staphylococcus aureus, bacteria from the Enterobacteriaceae group, and a systematic decrease in SCC in milk. The therapeutic effect was achieved via intravenous + intramammary or intramammary administration.

Sedimentation field-flow fractionation for rapid phenotypic antimicrobial susceptibility testing: a pilot study.

The increase in antibiotic resistance is a major public health issue. The development of rapid antimicrobial susceptibility testing (AST) methods is becoming a priority to ensure early and appropriate antibiotic therapy. To evaluate sedimentation field-flow fractionation (SdFFF) as a method for performing AST in less than 3 h. SdFFF is based on the detection of early biophysical changes in bacteria, using a chromatographic-type technology. One hundred clinical Escherichia coli strains were studied. A calibrated bacterial suspension was incubated for 2 h at 37°C in the absence (untreated) or presence (treated) of five antibiotics used at EUCAST breakpoint concentrations. Bacterial suspensions were then injected into the SdFFF machine. For each E. coli isolate, retention times and elution profiles of antibiotic-treated bacteria were compared with retention times and elution profiles of untreated bacteria. Algorithms comparing retention times and elution profiles were used to determine if the strain was susceptible or resistant. Performance evaluation was done according to CLSI and the ISO standard 20776-2:2021 with broth microdilution used as the reference method. AST results from SdFFF were obtained in less than 3 h. SdFFF showed high categorical agreement (99.8%), sensitivity (99.5%) and specificity (100.0%) with broth microdilution. Results for each antimicrobial were also in agreement with the ISO 20776-2 recommendations, with sensitivity and specificity of ≥95.0%. This study showed that SdFFF can be used as a rapid, accurate and reliable phenotypic AST method with a turnaround time of less than 3 h.