Increase In Compressive Stress Research Articles

Effects of laser shock peening on silicon nitride ceramic with varying sintering additive ratios

Silicon nitride ceramic (Si3N4) for industrial applications is conventionally manufactured with sintering additives, and the properties of Si3N4 change significantly based on the contents of these additives. In this study, we investigate the effects of laser shock peening (LSP) on Si3N4 sintered with varying ratios of sintering additives.The Si3N4 samples were sintered with a mixture of Y2O3, MgO, and SiO2 sintering additives at 5, 7, 9, and 11 wt%. A Nd:YAG laser (wavelength = 532 nm, maximum pulse energy = 1.4 J, repetition rate = 10 Hz, pulse duration = 8 ns, beam diameter = 11 mm, top-hat profile) was used to irradiate the Si3N4 samples. The samples were coated with a protective layer (100 μm thick aluminum foil) and a water layer to confine plasma. LSP of Si3N4 with 5% sintering additives resulted in a slight change in surface hardness but a 77% decrease in surface compressive residual stress. In contrast, LSP of Si3N4 with 11% sintering additives led to a simultaneous increase in surface hardness (7.3%) and surface compressive residual stress (67%), indicating a significant difference in the effectiveness of LSP depending on the ratio of sintering additives. Additionally, the surface of Si3N4 with 11% sintering additives showed evidence of grain refinement after LSP. It was demonstrated that the bending strength of Si3N4 with 11% sintering additives increased by 15.2%, and the depth of the fracture origin was significantly deepened.

Dislocation‐induced local symmetry reduction in single‐crystal KNbO3 observed by Raman spectroscopy

AbstractIn recent years, dislocation‐tuned functionalized ceramics have become one of the focal points of modern materials research due to their outstanding properties. These range from improved electrical conductivity and ferroelectric properties to dislocation‐enhanced toughening and superconductivity, caused by local strain fields. The aim of this work is to investigate the dislocation‐induced structural changes in single‐crystal KNbO3 by micro‐Raman spectroscopy. Dislocation‐rich regions with tailored densities have been generated using the Brinell indenter scratching method. The influence of the dislocations on the single‐crystal structure can be observed in the Raman spectra. The activation of additional Raman modes is observed, which does not occur in regions of low dislocation density. This observation is confirmed by DFT calculations of vibrational modes and is attributed to a reduction in the crystal symmetry due to increased defect densities in plastically deformed KNbO3. In addition, an increase in compressive stress at higher dislocation densities can be demonstrated by a blueshift in Raman mode positions.

Degradation mechanism for epoxy resins under combined electric, thermal and compressive stresses

Epoxy resins are widely used in equipment such as ultra-high voltage dry-type bushings, which are subjected to severe electric, thermal, and compressive stresses. Some physical mechanisms have already been proposed to explain the degradations generated by these different stresses, however their effects have not yet been quantified.. The degradation characteristics of epoxy resin under combined stresses of 8 kV/mm, 40 °C-120 °C, and 0–60 MPa were investigated in experiments. The results showed that the degradation characteristics turned significantly with the increase of compressive stress. With the increase in compressive stress, initially the partial discharge initiation voltage, tree initiation voltage and time to breakdown increased, and fractal dimension decreased. While the compressive stress exceeded the turning point, the characteristics were reversed. It can be suggested that opposing mechanisms exist. The free volume and phase field theories dominate at lower and higher stresses, respectively. A novel degradation model of the epoxy resin was proposed based on the theories above. When the compressive stress was low, the reduction of free volume played a dominant role in slowing down the degradation. When the compressive stress was high, the partial energy density concentration accelerated the degradation and played a dominant role. The molecular dynamics and finite element simulation of degradation process stress was carried out and proved consistent with experiments. It confirmed the proposed degradation model reliable and valid.

Tribological behavior and surface characteristics of severe surface plastic deformed as-cast and 3D-printed SS316L using LSP

The effect of laser shock peening (LSP) on as-cast and three-dimensional (3D)-printed SS316L alloys was studied. The LSP process was found more dominant than the 3D-printing technique over as-cast alloy steel for enhancing the properties. The process of laser shock peening results in microlevel changes in the structure of the material. This, in turn, leads to grain refinement and the increase of compressive residual stresses. After LSP treatment, the surface microhardness value increased by 33% in both as-cast and 3D-printed SS316L alloys with the hardness gradient from surface to subsurfaces. The wear rate of as-cast specimens and 3D-printed specimens were reduced to 1.28 10−6 and 1.14 10−6 g/m, respectively, and tensile value increased up to 22% after LSP treatment. The scanning electron microscopy images on the wear track confirm the vulnerability of the untreated SS316L alloys with adhesion wear and surface delamination. This difference was because the wear rate of the 3D-printed specimens was lesser than the as-cast SS316L alloys due to their layer-by-layer high-temperature finishing. The samples were characterized by optical microstructure to identify the surface refinement, and confirmed by the transmission electron microscope images along with specified area electron diffraction pattern for the accumulation of dislocation and grain refinement after LSP treatment. The accumulated residual stress was measured by X-ray diffraction technique and it found the highest compressive residual stress after LSP treatment was accrued by 3D-printed SS316L alloy with 310 MPa.

Self-Polymerized Tough and High-Entanglement Zwitterionic Functional Hydrogels.

Zwitterionic hydrogels exhibit great potential in biomedical applications due to their antifouling properties and biocompatibility. However, the single-network structure of pure zwitterionic hydrogels leads to a low toughness and strength, limiting their application in biomedical fields. In this work, a high entanglement sulfobetaine methacrylate-dopamine hydrogel (SBMA-DA-PE) with low cross-linker content and high monomer concentration is prepared by using a dopamine oxidative radical polymerization method. Compared to a regular zwitterionic hydrogel, the SBMA-DA-PE hydrogel exhibits a 5-fold increase in tensile fracture stress and a 10-fold increase in compressive fracture stress. The SBMA-DA-PE hydrogel possesses excellent mechanical properties (the maximum compressive stress ≥4.85MPa, the maximum compressive strain ≥90%). Besides, the non-covalent interactions between catechol or ortho-quinones within the SBMA-DA-PE hydrogel, combined with strong intermolecular electrostatic interactions, endow the SBMA-DA-PE hydrogel with great self-healing capabilities and fatigue resistance. The SBMA-DA-PE hydrogel demonstrates low swellability and possesses good antifouling properties. Furthermore, the good printability and conductivity of the tough SBMA-DA-PE hydrogel endows it with new possibilities for developing biological 3D scaffolds and electronic devices. Overall, this work provides new insights into the preparation of zwitterionic hydrogels with high mechanical strength and multi-functionality for biomedical applications.

Research on the effect of manufacturing processes on the fatigue life of TC4 fasteners

Abstract TC4 fasteners have the characteristics of high specific strength and yield ratio, excellent high and low temperature performance, corrosion resistance, etc., and are widely used in many fastener fields, including aerospace. In long-term use, fatigue fracture has become the main failure mode of TC4 bolt fasteners. The common manufacturing processes of TC4 fasteners include shot peening, bottom corner rolling pressure, anodizing and molybdenum disulphide coating, etc. At present, few researchers have studied the effect of the stress level of the manufacturing process on the fatigue life of TC4 fasteners. Therefore, this paper designs the process and parameter influence test from the perspective of different manufacturing processes, and analyses the fatigue test results to reveal the influence mechanism of different processes on the fatigue life of TC4 fasteners. The research results show that the increase of residual compressive stress greatly improves the fatigue strength of fasteners, the shot peening process improves the fatigue life of TC4 fasteners by increasing the residual stress of fasteners, and rolling pressure also increases the surface residual compressive stress. However, it is necessary to find suitable rolling parameter values, and anodizing reduces the residual compressive stress of fasteners. The coating of molybdenum disulfide also reduces the residual stress value of the fastener surface and leads to a decrease in fatigue life. Therefore, in order to control the fatigue life of TC4 fasteners, it is necessary to carry out the shot peening process, and control the rolling pressure, anodizing time and the coating thickness of molybdenum disulfide. The research in this paper provides a reference for the subsequent research on fastener fatigue strength control.

Strengthening effects of indentation notches on metallic glasses and their sensitivity to stress triaxiality

In this study, a metallic glass sample with an annular indentation notch was successfully constructed by a compression rod cyclic compression strategy using molecular dynamics simulation, and the mechanical behaviors of cut-notched metallic glass samples with the same stress triaxiality and notch size under triaxial compression were comparatively analyzed. It is found that the indentation notch further improves the strength and plasticity of the metallic glass, while it is insensitive to the cut-notched metallic glass with the same notch size. During triaxial compression, rejuvenation and shear softening lead to an increase in free volume, while diffusion and residual compressive stresses lead to a decrease in free volume. The stress triaxiality plays a key regulatory role in their competition and affects the final state of free volume change. This study provides a new theoretical basis and process idea for the enhancement of strength and plasticity of metallic glass.

Wear characteristics and micro-cutting damage model of cemented carbide by deep cryogenic treatment

Wear failure of oil drill bits leads to cost increase, and how to improve the abrasion resistance of cemented carbide (WC–Co) drill bits is an urgent problem, and deep cryogenic treatment (DCT) is a feasible method. The effect of DCT time (i.e., 0, 3, 6, 9, 12, 24, and 48 h) on the Vickers hardness, flexural strength, and wear rate of WC-Co with different Co contents (i.e., 5 wt%, 8 wt%, 10 wt%, and 12 wt%) was investigated. The results showed that the best DCT time for hardness, flexure strength, and abrasion resistance of WC-Co was 12 h. Compared with untreated (e.g., 0 h), the wear rates of WC-Co with different Co contents were reduced by 36%, 34%, 30%, and 19%, respectively at DCT-12. Compared with WC-12Co, the wear rate of WC-5Co with different DCT times was reduced by 75%, 77%, 78%, 78%, 80%, 79%, and 78%, respectively. The precipitation of η phase (Co6W6C), martensite phase transformation (α-Co to ε-Co), and the increase of residual compressive stress (RCS) of WC after DCT improved the hardness, flexural strength and reduced the wear rate of WC-Co. Based on the principle of frictional wear, a micro-cutting wear model considering Co content and DCT time is proposed, which can predict the evolution of the wear rate of WC-Co. The results of the study guide improving the wear resistance of drill materials.

Formation mechanism of blade surface integrity based on hybrid process of cryogenic minimum quantity lubrication and ultrasonic rolling strengthening process

This study proposes a hybrid process method based on Cryogenic Minimum Quantity Lubrication and Ultrasonic Rolling Strengthening Process (CMQL-URSP) to improve the surface integrity and enhance the mechanical properties of blade surface. First, the principle of the CMQL-URSP hybrid process was described. Second, the TEM experiments were conducted to clarify the influence of the CMQL-URSP hybrid process on aircraft engine blades. Finally, the blade processing experiments were performed to demonstrate the effectiveness of the CMQL-URSP hybrid process on the blade surface micro-morphology, micro-hardness and residual stress. The results indicate that the CMQL-URSP hybrid process effectively overcomes the limitations inherent to the solitary application of URSP. The CMQL process inhibits work hardening, thereby allowing the URSP to achieve better low-plastic surface improvement. Grain refinement governed by the continuous dynamic recrystallization mechanism leads to the formation of nanocrystals, which significantly improves mechanical properties of blade surface. The CMQL-URSP hybrid process results in a reduction in surface roughness from Ra 2.644 μm to Ra 0.055 μm, an increase in surface residual compressive stress from 321 MPa to 657 MPa, and the formation of a reinforced layer with a depth of 3.7 mm on the blade, thereby enhancing the surface integrity of the blade.

Gear contact fatigue prediction under mixed elastohydrodynamic lubrication with ellipsoidal asperity rough surface: Experimental and numerical investigation

A three-dimensional(3D) line-contact mixed lubrication model and contact fatigue life prediction model for gears are established, considering the elastoplastic contact of ellipsoidal asperities and their interactions. The localized lubrication states across the actual 3D rough surfaces are visually depicted. The direct asperity contact pressures calculation exhibits greater accuracy and universality. The proposed mixed lubrication model can be applied accurately and efficiently to heavy-load conditions. The synergistic mechanisms of multi-scale surface integrity parameters, such as surface morphology-lubrication coupling, hardness gradient, and residual stress, on gear contact fatigue has been revealed. The results reveal that surface roughness significantly affects the competitive failure mechanism between surface-initiated micropitting and subsurface-initiated macropitting. The increase in surface compressive residual stress is more sensitive to the enhancement of near-surface and subsurface fatigue lives, compared to the increase of peak residual stress and the depth of peak residual stress. The proposed physics-based gear contact fatigue life prediction model has been validated through gear contact fatigue experiments under various operating conditions. The maximum deviation between the predicted and experimental fatigue lives is within 10%. This paper presents theoretical methodologies and data-driven support for optimizing the design and manufacturing processes of gears, specifically focusing on enhancing anti-fatigue properties.

Compressive stress reduction in sputter-deposited yttrium aluminum nitride (Y0.2Al0.8N) thin films for BAW resonators with high electromechanical coupling

In the past decade, rare earth elements have found increasing interest in enhancing the piezoelectric coefficient of aluminum nitride (AlN) thin films. Until now, scandium has been the most successful rare earth element to enhance the piezoelectric coefficient (d33) up to 600 %. In this research paper, we present a 250 % increase in d33 to 12.5 pC/N for sputter-deposited yttrium alloyed aluminum nitride (Y0.2Al0.8N) thin films compared to pure AlN. However, this increase in d33 comes with a substantial increase in compressive layer stress well above 1 GPa. Therefore, a chamber pressure sweep technique is introduced, resulting in a 40 % reduction in the stress level without significantly affecting the crystallographic film parameters to facilitate device integration. Even more, high compressive stress in thin films is a critical concern in piezoelectric MEMS devices such as bulk acoustic wave (BAW) resonators, as it can adversely affect the piezoelectric material properties and hence, the electromechanical performance. For this purpose, we demonstrate that the pressure sweep technique improves the electromechanical coupling factor of Y0.2Al0.8N to 7.02 %, being substantially above the reference value of 6.02 % set by pure AlN. In summary, the findings from this study may stimulate further effort to integrate YxAl1-xN thin films in BAW filter devices for future telecommunication applications.

Stress engineering of SiCf/SiC composites: Interfacial stress adjustment and its effects on tensile behaviors of UD SiCf/SiC composites fabricated by hybrid CVI and PIP methods

Internal stress is usually generated during the preparation of the SiCf/SiC composites and is generally considered to be uncontrollable and detrimental to SiCf/SiC composite's mechanical properties. However, in this study, internal stress is proposed for the first time as a tool to regulate the interfacial bonding properties of the SiCf/SiC composites. And the interfacial compressive stress was successfully controlled by hybrid CVI and PIP methods. The results of Raman analysis show that the interfacial compressive stress increases with the increase of the PIP SiC content. The interfacial shear strength (τi) and interfacial dynamic friction strength (τf) was determined by micro-shear tests. Both τi and τf increase with the increase of interfacial compressive stress. With different interfacial bonding strength, the SiCf/SiC composites show different tensile behaviors. A high τi can lead to a high tensile modulus and proportional limit stress (PLS) and a high τf can lead to the disappearance of the second linear stage and low fracture strain. The axial residual stress of matrix also was tested, and the results indicate that it does not have a dominant influence on the mechanical properties. Finally, the SiCf/SiC composites achieve the superhigh PLS of 729.8 ± 9.2 MPa and modulus of 288.0 ± 7.9 GPa when the BN thickness is 100 nm and the interfacial compressive stress is 1127.7 MPa. This strategy of interfacial stress engineering may provide a new and valuable design idea for improving the mechanical properties of the SiCf/SiC composite and other composites. This strategy is also of great significance for broadening the design criteria and enriching the preparation methods and internal stress regulation methods of high-performance composites.

Evaluating mechanical and biological responses of bipolymeric drug-chitosan-hydroxyapatite scaffold for wounds: Fabrication, characterization, and finite element analysis

This study aims to explore the potential of a scaffold composed of drug-chitosan-hydroxyapatite (HA) in improving tissue treatment. The focus of the investigation lies in analyzing the physical and biological properties of the scaffold and evaluating its mechanical characteristics through finite-element analysis. To synthesize microcapsules containing dextran-diclofenac sodium, the electrospraying method was employed. The drug-chitosan-HA scaffold with varying volume fractions (VF) of the synthesized microcapsules (10, 15, and 20) was fabricated using the freeze-drying technique. Microscopic and scanning electron microscopy (SEM) images were utilized to evaluate the morphology, shape, and size of the microcapsules, as well as the porosity of the scaffolds for wound healing purposes. The mechanical properties of the synthesized microcapsules were determined via a nanoindentation test, while the mechanical behavior of the fabricated scaffolds was assessed through compression testing. Additionally, a multiscale finite-element model was developed to predict the mechanical properties of tissue scaffolds containing pharmaceutical microcapsules. The findings indicate that the incorporation of drug-chitosan-hydroxyapatite into the tissue significantly enhances both mechanical and biological responses. The mechanical evaluations demonstrate that the drug-chitosan-hydroxyapatite tissue exhibits excellent resistance to pressure, making it a suitable protective covering for skin wounds. Moreover, biological evaluations reveal that an increase in scaffold porosity leads to higher swelling behavior. The scaffold containing 20 % pharmaceutical microcapsules demonstrated the greatest swelling and desirable antibacterial properties, thereby indicating its potential as an effective wound dressing. Furthermore, a multiscale finite-element model was developed to predict the mechanical properties of tissue containing pharmaceutical microcapsules. The results indicated that the average size of the microcapsules was in the range of 170 to 180 µm, and the porosity of the prepared tissue was between 52 % and 61 %. The experimental compressive properties revealed that an increase in the volume fraction of the embedded microcapsules led to an increase in the maximum compressive stress and compressive modulus of the scaffolds by up to 54.95 % and 53.18 %, respectively, for the scaffold containing 20 % VF of pharmaceutical microcapsules compared to the specimen containing 10 % VF. In conclusion, the developed scaffold has the potential to serve as an effective wound dressing, with the ability to provide structural support, facilitate controlled drug release, and promote wound healing.

Mean Stress Correction in Low Cycle Fatigue Life of High Strength Steels

Fatigue strength of welded joints varies depending on the shape, filler metal, welding procedure, and post-treatment method. In addition, mean stress affects the fatigue behavior in terms of stress ratio. Typically, it is well known that tensile mean stress tends to decrease fatigue life while compressive mean stress increase fatigue life. There are various methods to incorporate the mean stress effect in fatigue strength, but there are relatively few correction methods in compressive mean stress, especially in low cycle fatigue regime.</br>In this study, a load-based fatigue test was conducted to evaluate the effect of mean stress on the welded joints of High Yield strength steel(HY Steel) with T-joint shape. The effect of the mean stress on the welded part of HY Steel with a T-joint shape was investigated using stress-based mean stress correction methods and strain-based mean stress correction methods. When the effective mean stress approach, which can correct compressive mean stress and tensile mean stress, is applied to HY Steel with a T-joint shape, it shows accurate correction result than stress-based mean stress correction method and strain-based mean stress correction method. Sensitivity parameters to consider mean stress for HY steel are presented.

Microstructure evolution and surface strengthening behavior of 300 M ultrahigh strength steel under engineered surface treatments

In this work, the most efficient and common engineered surface treatments identified as shot peening (SP), laser shock peening (LSP) and ultrasonic surface rolling process (USRP) were utilized to impact the 300 M ultrahigh strength steel. The microstructure evolution and surface strengthening behavior were carefully characterized and compared for the 300 M steel with various treatments. Besides, the underlying mechanisms for difference in grain refinement and surface mechanical properties by the arranged surface modification are revealed. The results indicate that a gradient structure with nano-grains at the top surface appears on the SP, LSP and USRP treated samples. The process of repeated impacts of SP in different directions leads to activation of multiple slip systems, which thus causes severe refined grains and dense dislocation activities associated with dislocation tangles, dislocation walls and blocking. A great variety of strikes per unit area by USRP results in higher plastic deformation compared to SP where numerous dislocation cells and deformation bands were generated. In contrast to SP and USRP, fewer slip systems are activated in LSP due to the short duration time which thus leads to the thinnest refined grain layer and more planar dislocation structures. The combination of low plastic work and lack of refined grains leads to lowest full width at half maximum (FWHM) in case of LSP samples whereas high FWHM comes from both fine grain size and dislocations in SP. The grain refinement and plastic work contributes to an increase of microhardness and compressive residual stress for the SP, LSP and USRP samples. To be clear, SP leads to a higher magnitude of hardness and compressive residual stress on the topmost surface while LSP causes a larger depth due to that shock wave in LSP influences material to much greater depth. Besides, the decomposition and redistribution of carbides are also noticed on the surface layer after the surface treatments with very high strain rate where numerous dislocations accumulate at the border of the carbides and slip trace is also observed within the carbides.

Investigation the effect of surface treatment on the mechanical properties of coating

AbstractThe study analyzed surface treatment's impact on mechanical properties of Fe-based amorphous coatings. Specimens underwent six-hour treatments at 670 and 770 °C using vacuum heat. Results revealed distinct mechanical features in the coating: Vickers hardness reached 755, scanning electron microscope images displayed glassy phases, showcasing good wear resistance and compressive residual stresses at around −55 MPa. A remarkable 122% increase in compressive residual stress was noted through combined vacuum heat treatment and sandblasting. Volume wear decreased from the initial 18 to 14 mm3 after treatment at 670 °C followed by sandblasting, indicating a 30% enhancement in wear resistance. Yet, using vacuum heat treatment at 770 °C negatively impacted the coating's properties.

Local buckling of the bottom flange in steel-concrete composite beams with trapezoidal corrugated webs subjected to end restraint at high temperatures

Steel-concrete composite beams with trapezoidal corrugated webs (SCBCW) are prone to rapid failure at high temperatures due to local instability of the bottom flange. The failure mechanism of SCBCW, which is an integral part of the holistic structure and subject to axial and rotational restraints from adjacent members at elevated temperatures, differs from conventionally simply supported steel-concrete composite beams with straight webs. To investigate the evolution of local buckling in the compressed flange of SCBCW under high temperature conditions, a composite beam model with frame restraints was developed using ABAQUS finite element software. In this model, the composite beam is connected to restraint frame columns through high-strength bolts. The changes in axial stress, bending moment, and deflection of the compressed flange of SCBCW were analyzed as temperature increased. Results indicate that at elevated temperatures, additional bending moments occur in the flange plane due to axial restraints, section temperature gradients, section negative bending moments and accordion effect caused by corrugated web on compressed bottom flange of SCBCW. This leads to a gradual increase in axial compressive stress before local buckling occurs followed by a decrease due to internal force redistribution upon onset of buckling. Studies show that initial buckling of bottom flange occurs on one side of flat section of web where axial compressive stress is relatively high while restraint effect on web is low; Subsequent local buckling of the beam then appears on opposite side adjacent flat section of web after initial buckle occure on one side. After local buckling appears on both sides of web tension bands appear on both sides where bottom flange experiences localized bucking. The setting of longitudinal stiffeners (LS) can effectively improve the local stability of the bottom flange of the composite beam, while the setting of transverse stiffeners (TS) has no significant impact.

Experimental and numerical study on the damage evolution and acoustic emission multi-parameter responses of single flaw sandstone under uniaxial compression

Cracks are generally the weakest position in engineering rock mass. It is of great practical significance to study the influence of cracks on the fracture process of rock mass and the precursor criterion of failure for disaster prevention and mitigation projects. In this paper, particle flow program (PFC2D) is used to analyze the mechanical strength and damage evolution of fractured rock. The multi-parameter stage characteristics of acoustic emission (AE) and the difference of fracture precursor information of fractured rock mass under uniaxial compression (UC) are explored. The results are as follows: (1) The strength and modulus of elasticity of fractured rock samples are smaller than that of intact rock mass, and increase in quadratic function with the increase of fracture angle, and the strength of B-90 sample is closest to intact rock samples; (2) The PFC analysis shows that the cracks in the defective rock samples all originate from the tip of the prefabricated crack, and the crack initiation angle is basically in the range of 60°∼90°. The loading process mainly produces tensile damage, and the number of tensile cracks are far more than that of shear cracks. Compressive stress and tensile stress increase with the increase of load, but the force chain of failure surface is the smallest after complete failure of rock; (3) The acoustic emission ringing number, RA/AF value, b value and entropy value of sandstone have obvious stage characteristics, the main frequency signal is mainly low frequency signal, and large-scale cracks are mainly produced in the failure process. The sudden increase point of AE ringing times and RA/AF value accumulation curve can be used as critical failure point. The fluctuation of B value and entropy value reflects the instability of fracture development, and “cliff-like” descending point and ascending point can be regarded as the precursor of critical failure of rock; (4) The failure precursor of acoustic emission parameters of sandstone appears in the peak load period of 85 %–98 %. The order of response time of different parameters is: cumulative RA/AF value, cumulative event number, entropy value, B value. The response time of B-45 and B-15 is earlier, while that of B-60 and B-30 is later. The research results are expected to deepen the understanding of the relevant standards of damage evolution and failure precursors of defective rocks in engineering applications.

Mechanical properties of steel fiber reinforced recycled concrete under compression-shear stress state

The continuous urbanization of construction has led to an increasing demand for concrete, resulting in large-scale gravel and river sand mining, which seriously affect the sustainable development of the environment. The waste concrete produced by the demolition of old buildings is processed into recycled aggregate to replace natural aggregate, and then the preparation of recycled concrete can effectively alleviate this problem. This paper investigates the mechanical properties of steel fiber reinforced recycled concrete (SFRRAC) under compression shear conditions, a compression shear test with 99 cubic specimens was designed, with the variation parameters being recycled aggregate concrete replacement rate, compressive stress, and steel fiber content. The failure mode of SFRRAC under compression-shear stress was observed, and the shear force-displacement curve was calculated. Furthermore, a thorough examination was performed to assess the mechanical characteristics of SFRRAC specimens under compression-shear stress. The findings of this study suggest that as the compressive stress increases, the failure characteristics of the specimens shift from exhibiting brittle failure to displaying ductile failure. The shear strength is most sensitive to the change in compressive stress. When the compressive stress reaches 6 MPa, the shear strength can reach 3.41 times that of the direct shear specimen. The shear strength of SFRRAC specimens is composed of the bond strength of concrete, shear expansion strength, and friction shear strength. The incorporation of steel fibers can modify the distribution of shear strength among the individual components. The adverse effect of the recycled aggregate replacement rate on the toughness index of the specimen is mainly concentrated after the peak point. Nevertheless, an elevation in compressive stress and the inclusion of steel fibers can counterbalance this detrimental influence. The shear strength calculation formula of SFRRAC in shear state is put forward, which has a reference value. This study provides an experimental reference and a theoretical basis for further examination of SFRRAC.

Impact of Date-Palm Fibers on Fine Soil’s Compaction and Strength Properties

This paper investigates the influence of date-palm fibers on the compaction and strength properties of fine soil. The laboratory tests, including specific gravity, compaction tests, and unconfined compression strength tests, were conducted, integrating different proportions (ranging from 0 to 2%) of date-palm fibers into the soil mixture. The palm fibers were divided into two distinct lengths (30 mm and 60 mm) to be mixed with the soil. Nine samples were prepared with varying proportions of date-palm fibers for the experimental investigation, aiming to specifically examine the influences exerted by both palm-fiber length and palm-fiber content on the soil's compaction and strength characteristics when mixed with date-palm fibers. The compaction test results demonstrate a decrease in the dry unit weight and an increase in the optimum moisture content by approximately 10%. Additionally, the length of the date-palm fibers impacts the optimum moisture content and the maximum dry unit weight of the soil mixture. In contrast, the unconfined compressive stress increased by about 30% with higher date-palm fiber contents. This increase in unconfined compressive stress due to increased date-palm fiber content is a significant finding, indicating improved soil strength. This finding holds the enhancing construction performance, sustainability, and cost-efficiency. In conclusion, this soil-fiber mixture shows suitable hydraulic applications. The utilization of natural materials in civil engineering demands the exploration of available natural fibers.