Increase In Pressure Research Articles

MTOR in the Development of Hypoxic Pulmonary Hypertension Associated with Cardiometabolic Risk Factors.

The pathophysiology of pulmonary hypertension is complex and multifactorial. It is a disease characterized by increased pulmonary vascular resistance at the level due to sustained vasoconstriction and remodeling of the pulmonary arteries, which triggers an increase in the mean pulmonary artery pressure and subsequent right ventricular hypertrophy, which in some cases can cause right heart failure. Hypoxic pulmonary hypertension (HPH) is currently classified into Group 3 of the five different groups of pulmonary hypertensions, which are determined according to the cause of the disease. HPH mainly develops as a product of lung diseases, among the most prevalent causes of obstructive sleep apnea (OSA), chronic obstructive pulmonary disease (COPD), or hypobaric hypoxia due to exposure to high altitudes. Additionally, cardiometabolic risk factors converge on molecular mechanisms involving overactivation of the mammalian target of rapamycin (mTOR), which correspond to a central axis in the development of HPH. The aim of this review is to summarize the role of mTOR in the development of HPH associated with metabolic risk factors and its therapeutic alternatives, which will be discussed in this review.

Periodontitis accelerates the onset of hypertension in spontaneously hypertensive rats, while the electrical activation of the carotid sinus nerve delays the beginning of the increase in blood pressure.

We have previously demonstrated that electrical stimulation of the carotid sinus nerve (CSN) protects the development of periodontitis. In the current study, we evaluated whether periodontitis accelerates the onset of hypertension in spontaneously hypertensive rats (SHR); and whether electrical stimulation of the CSN would delay the onset of hypertension. Three-week old SHR were implanted with electrodes around the CSN for electrical stimulation for 13 days. Bilateral ligation of the first molar and oral administration of Porphyromonas gingivalis induced periodontitis. The femoral artery of the SHR was cannulated, and 24 h later, in a conscious state, the blood pressure was recorded. Five-week old sham SHR (subjects without electrical stimulation of the CSN) did not demonstrate hypertension. However, when the SHR were submitted to periodontitis they exhibited hypertension at 5 weeks of age. Nevertheless, the stimulation of the CSN prevented the onset of hypertension. Periodontitis promoted alveolar bone loss in SHR; but, electrical stimulation of the CSN prevented this undesirable outcome following the exposure to periodontitis. Periodontitis accelerated the onset of hypertension in SHR; while the electrical stimulation of the CSN delayed the onset of hypertension.

HYPERTENSIVE CRISES: HYPERTENSIVE EMERGENCY AND CRISIS MANAGEMENT DURING ANESTHESIA

Introduction: hypertensive crisis is characterized by an acute and massive increase in blood pressure. Hypertensive crises encompass several clinical situations with different severity and prognosis, including hypertensive urgency and hypertensive emergency. The difference between the latter depends on whether the situation is life-threatening for the affected individual. Objective: to detail current information related to hypertensive crises, especially hypertensive emergency, definition, differentiation, etiology, epidemiology, pathophysiology, histology, clinical history, physical examination, management, differential diagnosis, prognosis and complications. Methodology: a total of 28 articles were analyzed in this review, including review and original articles, as well as clinical cases, of which 15 bibliographies were used because the other articles were not relevant to this study. The sources of information were PubMed, Google Scholar and Cochrane; the terms used to search for information in Spanish, Portuguese and English were: hypertensive crises, hypertensive emergencies, hypertensive emergencies, arterial hypertension. Results: approximately 1-2% of adults with hypertension suffer hypertensive crises. Multiple case series show that short-term treatment of hypertensive emergencies has good results; however, long-term results are unknown. The main drawback is that follow-up of individuals is lost and the medication regimen is frequently modified. Untreated hypertensive emergencies have very high morbidity and mortality and if the patient does not receive adequate education about the severity of hypertension, this trend is likely to continue. Conclusions: given the high prevalence of hypertension, it is crucial that health care professionals are able to differentiate between hypertensive emergencies and hypertensive emergencies to provide appropriate and timely treatment. Rapid blood pressure reduction is critical in the treatment of hypertensive emergencies. The choice of medications should consider both efficacy and safety to avoid further complications. A detailed clinical evaluation can help identify the underlying cause and guide treatment, highlighting the importance of an individualized approach. Lack of timely treatment can lead to severe consequences, emphasizing the need for proper management in critical situations. Constant training in the management of hypertensive emergencies is essential to reduce the morbidity and mortality associated with this condition.The management of hypertension during anesthesia is critical, as its prompt detection and control are fundamental to prevent serious complications. Despite the lack of specific criteria to suspend surgery in hypertensive patients, it is essential to evaluate each case individually, prioritizing target organ damage over blood pressure levels. KEY WORDS: crisis, emergency, urgency, hypertension.

Turbulent flow and wall forces in staggered square cylinder porous media: An LES Analysis

Abstract The Wall-Modeled-Large Eddy Simulation (WMLES) technique was used to analyze turbulent flow in a porous medium composed of a staggered arrangement of square cylinders. The study focused on a porosity range of 0.3 to 0.8 at a pore Reynolds number of 10×103. The research provides novel information on pressure and shear force distributions around the cylinders and time-averaged values of particle drag and fluctuating lift coefficients. Results indicate that the flow physics are mainly driven by an expansion region in front of the central particle and another in the rear, where the flow is contracted and strongly accelerated. In the first region, velocities, turbulence kinetic energy (k), and its dissipation rate (e) are attenuated by a sudden pressure increase, while in the contraction region, the effect is the opposite. As porosity decreases, flow gradients and the overall levels of k, e, and Reynolds stresses become more significant. Turbulent anisotropy increases as porosity decreases below 0.6. Hydrodynamic stresses in the last interval present relatively uniform levels, which is a unique feature that may be considered in designing dedicated engineering devices with controlled stresses.

Pressure-induced anomaly of transport properties and structural transition in layered ferromagnetic metal TlCo2S2

In this work, the structural and transport properties of ferromagnetic metal TlCo2S2 with ThCr2Si2-type crystal structure are systematically studied using high-pressure synchrotron x-ray powder diffraction, electrical transport measurements and first-principles calculations. All the resistances of TlCo2S2 between 1.4 GPa and 5.2 GPa exhibit an upturn at TS and an obvious hysteresis is observed below TS when measured in the cooling and heating processes. As the pressure increases, TS gradually increases and the resistances display a metallic behavior without any anomaly in the whole temperature region above 5.2 GPa, indicating that a possible structural phase transition occurs at TS and is beyond the room temperature above 5.2 GPa. High-pressure x-ray diffraction measurements combined with crystal structure prediction indicate that at room temperature TlCo2S2 undergoes a structural phase transition from a tetragonal phase (I4/mmm) to an orthorhombic structure (Bmab) at Pc ≈6.8 GPa, which is consistent with the results of the resistances under high pressure. Our results indicate that a first-order structural phase transition of TlCo2S2 is induced by high pressure and then results in the anomaly of the electrical transport properties.

Simulation and experimental research on the propagation mechanisms of acoustic energy inside the pipeline to detect the leakage

Leakage from pipelines has negative impacts on property and environment. The diameters of internal acoustic detectors in pipelines are small and not easily blocked, making it suitable for pipelines under various working conditions. Studying the characteristics of pipeline leakage sound signal and the propagation mechanisms within pipelines is crucial for timely detection of small leaks. In this study, a 3D simulation model of pipeline leakage was established, and a CFD/CAA hybrid calculation method was used to obtain effective leakage flow field information via LES. The equivalent sound sources in the flow field were extracted based on the Lighthill acoustic analogy theory. Determine the characteristic frequency range of the leakage sound signal was 1–2 kHz. This study founded that an increase in the leakage pressure and aperture size both lead to an enhancement in the leakage sound signal, and the propagation of leakage sound signal in pipelines is affected by background flow. An experimental pipeline leakage system was designed, and the accuracy of the simulation results was verified experimentally.

Dural arteriovenous fistula may be occluded through recanalization of impaired venous sinuses.

To investigate the effect and safety of recanalization of stenosed or occluded venous sinuses for dural arteriovenous fistulas (DAVFs) and possible mechanism of DAVF formation, patients with DAVF accompanied by venous sinus stenosis or occlusion treated with balloon angioplasty and/or stenting were retrospectively enrolled. The clinical data, treatment outcomes and complications were analyzed. In 7 patients enrolled, the DAVF was Cognard IIa grade in 3 (42.9% or 3/7) and IIa + b in 4 (57.1% or 4/7) patients, including complex DAVFs in 2 (28.6% or 2/7). The angioplasty procedure was successful in all (100%) patients, including complete cure in 3 (42.9% or 3/7) patients with the initial Cognard grade IIa, transformation from Cognard grade IIa + b to I in 2 (28.6% or 2/7) patients, and unchanged Cognard grade IIa + b in 2 (28.6% or 2/7) patients. The symptoms were all improved. At 3-month angiographic follow-up, 5 (71.4% or 5/7) cases were cured, whereas 2 cases still had grade I fistulas but no clinical symptoms. Staged embolization in 2 patients resulted in significant symptom improvement. At the last follow-up of a median 4 years, no clinical symptoms were present in 5 (71.4% or 5/7) patients, intermittent headache in 1 (14.3% or 1/7), and death from trauma in 1 (14.3% or 1/7). In conclusion, endovascular recanalization of occluded or stenosed venous sinuses using balloon angioplasty and stenting is able to induce occlusion of DAVFs and is a safe and efficient treatment approach for DAVFs which are possibly caused by significant pressure increase.

Outcomes of the Modified Warden Procedure for Partial Anomalous Pulmonary Venous Connection Drainage to a High Location in the Superior Vena Cava

To report the safety and effectiveness of a modified Warden procedure. Twenty-six (26) patients underwent modified Warden surgery at our centre from September 2017 to September 2021. In all patients, the superior vena cava (SVC) was reconstructed by turning the atrial wall in the main body of the right atrium upwards and applying fresh autologous pericardial patches. There were 13 male patients and 13 female patients, and the median age of the patients was 7.0 (range, 0.3-47.0) years. The median follow-up time after surgery was 47.0 (range, 32.0-80.0) months. The aortic cross-clamp time was 108.50±34.72 minutes, the cardiopulmonary bypass time was 154.81±41.65 minutes, the median postoperative mechanical ventilation time was 8.5 (range, 0.0-91.0) hours, the median intensive care unit stay was 43.5 (range, 15.0-352.0) hours, and the median length of postoperative hospital stay was 7.0 (range, 6.0-19.0) days. All patients were safely and successfully discharged from the hospital. No deaths or sinus node dysfunction occurred during the follow-up period. The mean gradient of the reconstructed SVC and/or the right pulmonary vein (PV) increased in eight patients and decreased to less than 1 mmHg in six patients. One (1) adult patient had already undergone two vascular interventions, and one child had persistent stenosis but did not undergo reoperation at the time of the study. In addition, two patients were subjected to pericardial windowing. A modified Warden technique using a right atrial flap and autologous pericardium effectively corrected the high-plane connection between the PVs and SVC. This technique effectively avoids sinus node dysfunction; however, a short-term increase in the differential pressure of the re-established SVC or PV after the procedure is acceptable, and reintervention is required only in rare cases.

Generalisation of the yield stress measurement in three point bending collapse tests: application to 3D printed flax fibre reinforced hydrogels

This paper describes the extrusion pressure's effect on composite hydrogel inks' filaments subjected to three point bending collapse tests. The composite considered in this work consists of an alginate-poloxamer hydrogel reinforced with flax fibres. Increased extrusion pressure resulted in more asymmetrical filaments between the support pillars. Furthermore, the material and printing conditions used in the present study led to the production of curved specimens. These two characteristics implicitly limit the validity of the yield stress equations commonly used in open literature. Therefore, a new system of equations was derived for the case of asymmetrical and curved filaments. A post-processing method was also created to obtain the properties required to evaluate this yield stress. This new equation was then implemented to identify the strength of failed hydrogels without flax fibre reinforcement. A statistical analysis showed this new equation's significance, which yielded statistically higher (i.e. 1.15 times larger) strength values compared to the numbers obtained with the open literature equations. At larger extrusion pressures, longer periods were needed for the material to converge towards its final shape. Larger extrusion pressure values led to lower yield stresses within the composite hydrogel filament: a 5 kPa increase in extrusion pressure lowered the yield stress by 19%. In comparison, a 15 kPa increase led to a 29% decrease in the yield stress. Overall this study provides guidelines to standardize three point bending collapse tests and analysis comparison between different materials.

Numerical simulation of condensation of supercritical water gasification products in a supersonic nozzle

The clean and efficient separation of supercritical water gasification products (SCWGP) has emerged as a significant challenge in supercritical water gasification technology. This paper proposes the use of a supersonic nozzle for the condensation and separation of H2 and CO2 from SCWGP, leveraging the high-pressure characteristics of these products. By establishing a flow model and a condensation model for the supersonic nozzle, the effects of inlet pressure and inlet temperature on the condensation process are analyzed. The analysis reveals that the latent heat released during condensation causes an abnormal distribution of pressure and temperature within the nozzle. When the inlet pressure of the nozzle is increased from 7.0 to 9.0 MPa, the liquid phase mass fraction at the outlet rises from 5.3 × 10−3 to 0.056. Similarly, when the inlet temperature is lowered from 300.0 to 290.0 K, the liquid phase mass fraction at the outlet also rises from 5.3 × 10−3 to 0.058. The increase in inlet pressure leads to the condensation location shifting toward the throat by ∼8.5 × 10−3 m⋅MPa−1, while the impact of inlet temperature is approximately −2.3 × 10−3 m⋅K−1. The nucleation rate in the nozzle is always concentrated in a small region.

Study on the sealing performance of 105MPa conical core BOP in the fully sealed state

Achieving full sealing is a technical challenge in the simulation, manufacturing, and experimentation of annular anti-spray seals. Based on Yeoh rubber constitutive model and large deformation theory, the finite element simulation model of 105 MPa annular blowout prev conical core seal was established, the stress distribution and contact pressure law of the core under different working pressures and full sealing conditions were analyzed, the full sealing state simulation of 105 MPa annular blowout prev core was realized, and the sealing performance of the core was evaluated. The results show that the conical core can meet the sealing requirements at 105 MPa. The high stress of the conical rubber core of 323 MPa appears at the joint of the inner wall of the rubber core and the back of the support bar and the joint of the upper and lower convex of the support bar. The high stress of 892 MPa appeared in the neck and back of the upper plate and the rear area of the lower plate. When the piston operating pressure is constant, with the increase of the working pressure, the overall stress of the rubber core increases, which is easy to cause the fatigue failure of the rubber core.

Characterizing undrained behaviour of imperfectly saturated Palar sand

The occurrence of earthquake-induced soil liquefaction poses a significant threat, leading to extensive damage to building foundations and other structures, resulting in substantial economic repercussions. The seismic performance of geotechnical systems is markedly influenced by the saturation level of the soil. This study examines the impact of dynamic response on Palar sand. Cyclic triaxial tests were conducted on partially saturated fine-grained loose sand with a relative density of 35 % and a degree of saturation ranging from 65 % to 75 %. These tests were carried out at a strain rate of 0.1 % and confining pressures of 50 and 75 kPa. The study findings reveal that an increase in back pressure corresponds to a rise in the excess pore water pressure ratio of the sand. Additionally, the sand undergoes liquefaction as the number of cycles increases, and the degree of saturation decreases for different confining pressures at frequencies of 0.75 and 1 Hz. It was observed that soil liquefies more rapidly at lower strain rates with an increase in effective confining pressure. Conversely, at higher frequencies, soil liquefaction occurs in a smaller number of cycles. Comparing the effects of confining pressure and frequency, a damping ratio of 13 % and a shear modulus of 40 MPa were achieved at a frequency of 0.75 Hz and a confining pressure of 50 kPa. The shear modulus of partially saturated sand decreases with an increase in the initial degree of saturation due to specific characteristics of the Palar sand and the loading conditions.

The distribution of environmental pressures from global dietary shift

Abstract The production and consumption of food is one of the main drivers of environmental change globally. Meanwhile, many populations remain malnourished due to insufficient or unhealthy diets. Increasingly, dietary shifts are proposed as a means to address both environmental and health concerns. We have a limited understanding of how dietary shifts could alter where food is produced and consumed and how these changes would affect the distribution of environmental pressures both globally and across different groups of people. Here we combine new food flow data linking producing to consuming country with environmental pressures to estimate how a global shift to each of four diets (Indian, EAT-Lancet, Mediterranean, and mean Food Based Dietary Guidelines) could affect environmental pressures at the global, country income group, and country level. Globally, cumulative pressures decrease under the Indian, EAT-Lancet, and Mediterranean scenarios and increase under Food Based Dietary Guidelines. On average, low income countries increase their cumulative consumption and production pressures while high income countries decrease their consumption pressures, and typically decrease their production pressures. Increases in low income countries are likely due to the nutritional inadequacy of current diets and the corresponding increases in consumption quantities with a shift to our diet scenarios. Despite these increases, we believe that three out four of our simulated dietary shifts can be seen as a net benefit by decreasing global pressures while low income countries increase pressures to adequately feed their populations. Additionally, considering principles of fairness applied, some nations are more responsible for causing historical environmental pressures and should shoulder more of the change. To facilitate more equitable shifts in global diets, resources, capacity, and knowledge sharing of sustainable agricultural practices are critical to minimize the increases in pressures that low income countries would incur to adequately feed their populations.

COMPARATIVE EVALUATION OF CARDIOVASCULAR PARAMETERS OF PROPOFOL / ETOMIDATE FOR ABDOMINAL SURGERIES IN CALVES

The calves presented with abdominal affections requiring surgical interventions were randomly divided into group I and group II with seven animals in each group. All the animals were premedicated with dexmedetomidine at 2 µg/kg body weight, pentazocine at 1 mg/kg body weight and midazolam at 0.2 mg/kg body weight intravenously. In group I and group II, anaesthetic induction was carried out with propofol at 2 mg/kg body weight and etomidate at 0.25 mg/kg body weight intravenously, respectively. Both the groups were maintained in Isoflurane anaesthesia with modified oro-endotracheal tube. The cardiovascular parameters such as heart rate, mean arterial blood pressure, systolic and diastolic blood pressure were monitored during different stages of anaesthesia in both the groups. In both the groups, a significant decrease in heart rate was noticed after premedication and anaesthetic induction. A Significant increase was noticed in systolic blood pressure values after anaesthetic induction and 10th minute of anaesthesia in group I and a highly significant increase was noticed after induction up to 10 minutes in group II. A highly significant increase in diastolic blood pressure was noticed after induction and 10th minute in group I, whereas significant increase was noticed in mean arterial pressure after induction and 15th minute of anaesthesia in group II animals. The cardiovascular parameters recorded in the present study concluded etomidate produced better cardiovascular stability and minimal respiratory depression compared to propofol throughout the anaesthetic period.

Sensitivity Analysis of Depth-Controlled Oriented Perforation in Horizontal Wells Based on the 3D Lattice Method

The main method used to exploit unconventional oil and gas reservoirs involves multi-cluster perforation combined with hydraulic fracturing in horizontal wells. However, as the use of this technology has expanded, challenges like reduced perforation efficiency and elevated fracture initiation pressure have surfaced. The depth-controlled oriented perforation technique helps achieve uniform fracture initiation, enhance efficiency, and lower initiation pressure. In this study, a hydraulic fracturing fluid–solid coupling model at the perforation scale was established using the 3D lattice method to compare the near-wellbore fracture morphologies of depth-controlled oriented perforation, spiral perforation, and oriented perforation. Additionally, this study analyzes the effects of injection rate, reservoir elastic modulus, and horizontal stress difference on the fracture morphology and initiation pressure of depth-controlled oriented perforation. This study clarifies the applicability of depth-controlled oriented perforation in different types of reservoirs for the first time. The results indicate that intermediate fractures between spiral and oriented perforations are hindered, while depth-controlled oriented perforation ensures uniform fracture initiation. In the injection rate range of 0.144 to 0.360 L/min, an increase in injection rate accelerates the rise of fluid pressure within the perforations, leading to an increase in fracture initiation pressure. Therefore, excessively high injection rates are unfavorable for fracture initiation. Through depth-controlled oriented perforation, long and singular fractures can be formed in reservoirs with significant horizontal stress differences and high elastic moduli.

Exaggerated postnatal surge of orexin neurons and the effects of elimination of excess orexin on blood pressure and exaggerated chemoreflex in spontaneously hypertensive rats.

An overactive orexin (OX) system is associated with neurogenic hypertension and an exaggerated chemoreflex in spontaneously hypertensive rats (SHRs). However, the chronology and mechanism of this association is unclear. We hypothesized that increased postnatal neurogenesis of OX neurons in SHRs precedes and contributes to the aberrant increase in mean arterial blood pressure (MAP) and the exaggerated response to hypercapnia during postnatal development. Using immunohistochemical methods and bromodeoxyuridine, we mapped the timeline of orexin neuron neurogenesis and maturation during early postnatal development. We then used whole-body plethysmography with EEG and EMG to map the development of mean arterial pressure (MAP) and state regulation. Finally, we used OX-targeted saporin toxin to determine the effects of eliminating excess OX neurons on the elevated MAP and exaggerated chemoreflex in adult SHRs. We found that both SHRs and Wistar-Kyoto (WKY) rats experienced postnatal increases in OX neurons. However, SHRs experienced a greater increase than WKY rats before P15, which led to significantly more OX neurons in SHRs than age-matched WKY controls by P15-16 (3,720 ± 780 vs. 2,406 ± 363, p = 0.005). We found that neurogenesis, as evidenced by BrdU staining in OX-positive neurons, was the primary contributor to the excess OX neurons in SHRs during early postnatal development. While SHRs develop more OX neurons by P15-16, SHRs and normotensive WKY control rats have similar MAP during postnatal development until P25 in wakefulness (81.6 ± 6.6 vs. 67.5 ± 6.8mmHg, p = 0.006) and sleep (79.3 ± 6.1 vs. 66.6 ± 6.5, p = 0.009), about 10 days after the surge of OX neurons. By selectively eliminating excess (∼30%) OX neurons in SHRs, we saw a significantly lowered MAP and hypercapnic ventilatory chemoreflex compared to non-lesioned SHRs at P40. Additionally, we found unique signatures in state indicative of the attention defecit phenotype commonly associated with this model. We suggest that the postnatal increase of OX neurons, primarily attributed to exaggerated postnatal OX neurogenesis, may be necessary for the development of higher MAP and exaggerated chemoreflex in SHRs, and modulation of the overactive OX system may have a potential therapeutic effect during the pre-hypertensive period.

Factors Associated with Retinal Microvasculature Dropout Induced by Elevation of Intraocular Pressure in Primary Open-Angle Glaucoma.

To investigate the risk factors related to decrease in vessel density (VD) observed in primary open-angle glaucoma (POAG), due to acute increase in intraocular pressure (IOP) by an ophthalmodynamometer (OPD). This cross-sectional study involved 42 eyes of participants (22 Controls and 20 POAG patients) that underwent optical coherence tomography angiography (OCT-A) to assess VD in the peripapillary region in three examination sets: primary gaze position (1), 25-degree adduction (2) and 25-degree adduction with OPD compression (3). Individual relationships between IOP levels and changes in the superficial complex VD were evaluated after image processing and exclusion of large retinal vessels. Multivariable regression analysis was used to verify factors associated with differences in VD induced by IOP elevation. A significant increase in IOP was induced by OPD compression during adduction (mean ± SD, Control: + 13.8 ± 2.8; POAG: + 13.4 ± 2.1mmHg). Only during IOP elevation (set 3), a significant VD decrease was observed both in POAG eyes (p = 0.008) and controls (p = 0.022). Baseline IOP (p = 0.022), maximum IOP (p = 0.003), and scleral rigidity (p = 0.029) were significantly associated with VD decreases in eyes with POAG. No changes were observed in VD during adduction gaze exclusively. Acute IOP elevation induced with OPD, but not adduction gaze, decreased peripapillary VD measured with OCT-A imaging. IOP levels and scleral rigidity significantly affected VD reduction in POAG patients. Thus, high scleral rigidity may decrease the ability of the globe to dampen the well-known effects of IOP fluctuation on glaucoma onset and progression. What is known Decrease vascular density in the peripapillary retina was associated with POAG, but factors related to the vascular response to elevated IOP are unexplored. What is new OCT-A quantification shows decreases in vascular density of the superficial layers of the peripapillary retina during an acute elevation in IOP. High IOP levels and scleral rigidity significantly affected vascular density reduction in POAG patients.

High-Temperature Fatigue Degradation Behaviors of a 3D Braided C/SiC with a Thin Interlayer in Different Dry Oxygen Atmospheres

In order to evaluate the increase in the flexural strength of a 3D braided C/SiC composite comprised with a thin pyrolytic carbon (PyC) interlayer (TI C/SiC) under a load of 60 MPa with an amplitude of ±20 MPa at an oxygen partial pressure of 8000 Pa, the effect of temperature, oxidation and stress value on the length change in the sample, fracture behavior, residual flexural strength and fracture morphology were studied up to 1500 °C. It was found that the gauge length change behaviors of the material are related to (i) the positive damage of the thin interlayer and (ii) to the negative damage of the C phase. The most serious damage of TI C/SiC under 60 ± 20 MPa occurs in an oxygen partial pressure of 17,000 Pa at 1300 °C. When the oxygen partial pressure and/or the temperature are reduced, the positive C phase damage is relieved. In the case that the oxygen partial pressure, temperature and stress increase, the negative C phase damage is facilitated. The oxidation mechanism of the C phase is controlled by the inward diffusion of oxygen from the sample surface to the center; however, a higher stress is considered to change the oxygen diffusion mechanism by increasing the reaction of the C phase, with oxygen causing a widening of microcracks.

A variable damping viscous damper for control of buildings under wind loading

High-rise buildings are susceptible to low-frequency vibrations induced by wind loading, and the traditional constant damping viscous damper (CDVD) falls short in effectively suppressing vibrations of high-rise buildings under wind loadings because of its constant damping coefficient. To address this, a novel variable damping viscous damper (VDVD) is first designed and fabricated. The characterization tests were conducted to evaluate the variable damping characteristics under different velocities. The control performance of the VDVD in high-rise buildings under wind loadings with varying wind pressures is simulated and analysed, as comparisons with CDVD. The test results show that the damping coefficient of the VDVD increases with the input velocity. Furthermore, it exhibits the capability to achieve both constant and variable damping through the adjustment of the pre-pressure force in the spring. Compared with cases using CDVD, the VDVD demonstrates a significantly greater reduction in structural response, with cumulative dissipated energy ratios ranging from 1.0 to 3.14 as wind pressure increases. The VDVD offers excellent potential for various engineering applications in terms of new concepts and new devices for vibration control and mitigation induced by wind loadings.

Numerical investigations into the comparison of hydrogen and gas mixtures storage within salt caverns

Salt caverns, long used for natural gas storage to manage peak loads, are being considered for hydrogen storage as part of the shift towards greener fuels. This transition necessitates re-evaluating heat and fluid transport to ensure the suitability of storage sites. A comparative analysis between current (natural gas and compressed air) and prospective (hydrogen and gas mixtures) storage systems was conducted using a standardized historical cycle over thirty days to identify trends. Hydrogen exhibited the lowest cumulative temperature and pressure increase (17 °C, 0.40 MPa), but the greatest variability per cycle, with an average range of 26 °C and 1.6 MPa. This higher fluctuation could potentially limit its use in short-term cycles compared to natural gas. Moreover, hydrogen's storage capacity was found to be a third of natural gas's, at only 6.6 GWh for the cavern design and specified pressure limits. These findings indicate that while hydrogen presents a greener alternative, its high variability and lower storage capacity pose challenges for its use in existing infrastructure, highlighting the need for further research to optimize its storage and utilisation in energy systems.