Improvement In Output Voltage Research Articles

Perovskite Nanocrystals Induced Core-Shell Inorganic-Organic Nanofibers for Efficient Energy Harvesting and Self-Powered Monitoring.

The emerging field of wearable electronics requires power sources that are flexible, lightweight, high-capacity, durable, and comfortable for daily use, which enables extensive use in electronic skins, self-powered sensing, and physiological health monitoring. In this work, we developed the core-shell and biocompatible Cs2InCl5(H2O)@PVDF-HFP nanofibers (CIC@HFP NFs) by one-step electrospinning assisted self-assembly method for triboelectric nanogenerators (TENGs). By adopting lead-free Cs2InCl5(H2O) as an inducer, CIC@HFP NFs exhibited β-phase-enhanced and self-aligned nanocrystals within the uniaxial direction. The interface interaction was further investigated by experimental measurements and molecular dynamics, which revealed that the hydrogen bonds between Cs2InCl5(H2O) and PVDF-HFP induced automatically well-aligned dipoles and stabilized the β-phase in the CIC@HFP NFs. The TENG fabricated using CIC@HFP NFs and nylon-6,6 NFs exhibited significant improvement in output voltage (681 V), output current (53.1 μA) and peak power density (6.94 W m-2), with the highest reported output performance among TENGs based on halide-perovskites. The energy harvesting and self-powered monitoring performance were further substantiated by human motions, showcasing its ability to charge capacitors and effectively operate electronics such as commercial LEDs, stopwatches, and calculators, demonstrating its promising application in biomechanical energy harvesting and self-powered sensing.

Improvement of output voltage from shading interference on solar cell using a reflector system

One of the factors that affect the performance of photovoltaic cells is shading. Shading can reduce the intensity of solar radiation on the cells. This study aims to design a system that can improve the amount of voltage from shading disturbances to optimise the output voltage on the solar cell by using a reflector. The reflector is designed in a flat mirror measuring. It is expected that there will be an increase in the output voltage of the existing solar cell system. The more reflected light that hits the surface of the solar panel and illuminates the shading area, the more significant the increase in output voltage, current and power, and vice versa.

Enhancing the Performance of Fabric-Based Triboelectric Nanogenerators by Structural and Chemical Modification

Fabric-based triboelectric nanogenerators (TENGs) are promising candidates as wearable energy-harvesting devices and self-powered sensors. Booting the power generation performance is an eternal pursuit for TENGs. Herein, an efficient approach was proposed to enhance the triboelectric performance of commercial velvet fabric by enriching the fiber surface with hierarchical structures and amide bonds through chemical grafting of carbon nanotube (CNT) and poly(ethylenimine) (PEI) via a polyamidation reaction. With an optimized modifier concentration, the fabric-based TENG easily achieved over 10 times improvement in output voltage and current at a low modifier content of less than 1 wt %. The modified-fabric-based TENG was fully washable and exhibited excellent robustness and long-term stability. With a maximum power density of 3.2 W/m2 achieved on a 5 × 106 Ω external resistor, the TENG was able to serve as a power source for various small electronics such as pedometer, digital watch, calculator, and digital timer. In addition, the TENG demonstrated capability in self-powered tactile and pressure sensing and promising potential in human-computer interface applications. The approach proposed provides a feasible path for boosting the triboelectric performance of fabric-based TENGs and gives insights into the design of fabric-based nanogenerators and smart textiles.

Self‐Assembly of Porous Microstructured Polydimethylsiloxane Films for Wearable Triboelectric Nanogenerators

AbstractTriboelectric nanogenerator (TENG), a green energy harvester, can harvest mechanical energy from human motion to electric energy to be applied in wearable electronics and sensor network. Porous materials played an important role in enhancing electric performance of TENG. In this paper, Azobisisobutyronitrile (AIBN) is used as a self‐reactive agent to modify Polydimethylsiloxane (PDMS) to form a self‐assembled porous structure (PDMS‐N10 film) through the difference in temperature between PDMS pre‐curing and AIBN decomposition. The PDMS‐N10‐based TENG exhibits a 2.5‐fold and 2.7‐fold improvement in output voltage and current as compared with PDMS without modification respectively. In addition, 116 light‐emitting diodes could be lighted up and 22 µF capacitor is charged. The TENG is also used as a sensor or trigger device for sensing the movements of elbow, knee, wrist, or finger, which can be applied in wearable devices because of the flexibility and durability as well as low cost.

Novel voltage balancing algorithm for single‐phase cascaded multilevel inverter for post‐module failure operation in solar photovoltaic applications

Four cascaded quasi-impedance source inverter (qZSI) modules are required for achieving nine-level output voltage waveform. In case of one module failure, number of levels in output voltage are reduced to seven. This leads to decrease in the output voltage magnitude and increased THD (higher than conventional seven-level qZSI). This is due to the dominance of unwanted harmonic component introduced in the harmonic spectrum. To restore voltage magnitude and optimize THD performance, novel voltage balancing algorithm is proposed. To validate the control algorithm for off-grid and grid connected system, simulation results of the multilevel qZSI are discussed in two categories: (i) DC voltage source powered multilevel qZSI for RL load subjected to module failure and (ii) solar powered multilevel qZSI connected to utility grid subjected to module failure and variable solar irradiation. Pre-fault and post-fault performance of the system with the proposed control algorithm is discussed for both categories, which validates the effectiveness of the algorithm. Hardware results for proof-of-concept are discussed for DC voltage source fed cascaded qZSI connected to RL load during pre-fault and post-fault conditions. FPGA Virtex-5 is used for hardware implementation of the control algorithm. The results validate the improvement in output voltage both quantitatively and qualitatively.

High-performance flexible triboelectric nanogenerator based on porous aerogels and electrospun nanofibers for energy harvesting and sensitive self-powered sensing

Finding new means to enhance the performance of triboelectric nanogenerators (TENGs) is an ongoing pursuit. We report a novel flexible TENG made of highly porous cellulose nanofibril (CNF)/polyethylenimine (PEI) aerogel film paired with polyvinylidene fluoride (PVDF) nanofiber mats that exhibits outstanding triboelectric outputs. Modifying CNF with PEI not only enhances the mechanical properties of the CNF/PEI aerogel, but also greatly improves the power density by 14.4 times due to the enhanced tribopositivity. The triboelectric performance is further improved by employing multiple layers of PVDF mats. The TENG made of the CNF/PEI aerogel paired with four layers of PVDF mats exhibited an 18.3 times and 97.6 times improvement in output voltage and power density, respectively, compared to the TENG made of one layer of PVDF mat. The peak output power density reached 13.3 W/m2 at a load resistance of 106 Ω. Furthermore, the novel TENG displays extraordinary sensitivity when used as a self-powered sensor. It can detect not only human motion like arm bending and footsteps, but also small forces like finger tapping, water dripping, and the vibration of the substrate it is attached to. Therefore, this study not only demonstrates a high performance TENG, but also provides new insights into the design, fabrication, and application of TENGs.

Prospects of Tunnel FETs in the Design of Power Management Circuits for Weak Energy Harvesting DC Sources

In this paper, a new tunnel FET (TFET)-based power management circuit (PMC) is proposed for weak dc energy harvesting sources. Thanks to their particular carrier injection mechanisms, TFETs can be used to design efficient energy harvesting circuits by enabling the power extraction from sources which are not only at very low voltage levels (sub-0.1 V) but also at very low power levels (a few nW). As TFET devices are designed as reverse-biased diodes, changes in conventional circuit topologies are required in order to take full advantage of these emerging devices. The circuit design techniques proposed in this paper represent an improvement in output voltage and input power range with respect to previously published TFET-based PMCs. Simulation results show that the TFET-based PMC can sustain itself from a 2.5 nW@50 mV dc source, powering a load at 0.5 V with 29% of efficiency.

Polarity tuning of single-walled carbon nanotube by dipole field of ferroelectric polymer for thermoelectric conversion

The tuning of the Seebeck coefficient of a single-walled carbon nanotube (SWCNT) film was achieved by using the dipole field of a ferroelectric polymer. The Seebeck coefficient was positive under an up-poling dipole field, but negative under a down-poling dipole field, whereas the control remained positive. This tunable behavior can be explained by selective carrier injection and accumulation, which was confirmed by the temperature dependence of electrical conductivity. Connecting p- and n-type SWCNT films tuned by dipole fields to create a π module resulted in a significant improvement in output voltage owing to the temperature difference between the two.

誘導型パルスパワー発生装置におけるヒューズ冷却水抵抗を考慮した出力電圧上昇法

誘導型パルスパワー発生装置におけるヒューズ冷却水抵抗を考慮した出力電圧上昇法

Improvement of Output Voltage in IR Sensor Using Semiconductive Fiber by Treatment of High-Voltage Pulse

Improvement of Output Voltage in IR Sensor Using Semiconductive Fiber by Treatment of High-Voltage Pulse