Implantation Technique Research Articles

Imaging fibrinogen assembly on calcium-doped titanium by using scanning electrochemical microscopy

Fibrinogen adsorption is a critical host response to the insertions of various medical devices. Scanning electrochemical microscopy (SECM) has the power to probe the local interactions between proteins and bulk solids in liquid environments; however, our knowledge of the distribution or the assembly structures of protein adsorption is limited. Here, fibrinogen assembly behaviors on calcium-doped titanium are imaged by resolving the strength of the SECM probe’s negative feedback in two-dimensional micro-regions. By using ion implantation techniques, calcium and/or silver were doped into polished titanium surfaces. The calcium-doped titanium was capable of releasing calcium, while the clean titanium and silver-doped titanium did not release their constituents. The two-dimensional discontinuous distribution of the probe current/steady current (i/i0) values were only detectable in calcium-doped groups, and this was incubating duration dependent, showing the micro-regions preferential for fibrinogen assembly in calcium-doped groups. This was consistent with the fibrinogen adsorption morphologies on calcium-doped titanium examined by dye-assisted scanning electron microscopy. It is concluded that protein assembly behaviors on bulk solid surfaces in liquid environments can be imaged by resolving the distribution of the SECM probe currents in two-dimensional areas. The method is promising in illuminating the true surface-protein interactions and the protein adsorption structure–function relations.

Jailed high-pressure balloon technique is superior to jailed wire technique in protecting side branch of coronary bifurcation lesions

Objectives. This study investigated the influence of higher pressure protection with a small diameter balloon of side branch (SB) on bifurcation lesions. Background. Of the different coronary stent implantation techniques, the modified jailed balloon technique has become a viable option for bifurcation lesions. However, there was no detailed study on the relationship between the balloon inflation pressure of the main vessel (MV) and SB. Methods. In this study, we collected information of patients who underwent percutaneous coronary intervention (PCI) for bifurcated lesions between March 2019 and December 2022. They were divided into two groups according to the operation way: active jailed balloon technique (A-JBT) group and jailed wire technique (JWT) group. Results. A total of 216 patients were enrolled. The A-JBT group had a larger SB stenosis diameter (1.53 ± 0.69 vs. 0.95 ± 0.52, p < .001), the lower degree of stenosis (44.34 ± 18.30 vs. 63.69 ± 17.34, p < .001) compared to the JWT group. However, the JWT group had a higher incidence of SB occlusion (18.0% vs. 1.9%, p < .001) compared to the A-JBT group. Nevertheless, the success rate for both groups was 100%. Conclusions. This novel high inflation pressure and small diameter balloon approach we propose has significant advantages. There is a lower rate of SB occlusion and SB dissection, which is more cost-effective and provides better clinical outcomes for the patient. This method should be considered in the future for treating bifurcation lesions.

Effect of different impression coping and scan body designs on the accuracy of conventional versus digital implant impressions: An in vitro study

ObjectivesThis in vitro study compared the accuracy of conventional versus digital impression techniques for angulated and straight implants using two different impression coping and scan body designs. MethodsTwo implant systems were used: Straumann and Dentegris. Two implants were placed for each system, straight and angulated at 15 degrees mesiodistally. Conventional impressions were made using the splinted open-tray technique using narrow impression coping (NIC) and wide impression coping (WIC). The stone casts produced from the conventional impression were digitized with a lab scanner (3Shape D2000). Digital impressions were made using four intraoral scanners (IOS): 3Shape Trios 3, Medit i700, Cerec Omnicam, and Emerald Planmeca using short scanbodies (SSB) and long scanbodies (LSB). The scanning was repeated ten times to generate the Standard Tessellation Language (STL) files. The distance and angle deviations between impression copings and scanbodies were measured in reference to the master model. ResultsThe trueness and precision of SSB and WIC were significantly better than LSB and NIC (p<0.001). The range trueness of the platform deviation was better with SSB (37.1 to 51.9) than LSB (89.6 to 127.9 μm) and for WIC than NIC in conventional impressions (58.2 and 75.1 μm, respectively). The trueness of the angle deviation of digital scans with SSB (0.11 to 0.25 degrees) was significantly better than scans with LSB (0.31 to 0.57 degrees) and for WIC than NIC (0.21 and 0.52 degrees, respectively). The precision of the platform deviation of digital scans with SSB (12.4 to 34.5 μm) was higher than other scans and conventional impressions (42.9 to 71.4 μm). The precision of the angle deviation of Medit i700 and Trios 3 with SSB (0.17 and 0.20 degrees, respectively) was higher than other scans with SSB and conventional impressions (0.54 to 1.63 degrees). ConclusionsDigital scans with SSB were more accurate than conventional splinted open-tray impressions. The type of impression coping and scanbody significantly affected the impression accuracy. Clinical significanceThe use of a short scanbody can increase the accuracy of digital impressions, and wide impression coping can increase the accuracy of conventional impressions, resulting in improved clinical outcomes.

Biventricular Resynchronization: Case Report and Literature Review

Cardiac resynchronization therapy (CRT) was introduced to restore left ventricular synchrony in patients with heart failure. Currently, more than 30% of patients do not respond to this therapy. CRT has proven its effectiveness in reducing morbidity and mortality in well-selected patients. A better understanding of the pathophysiological mechanisms, implantation techniques, and technological advances in devices has improved the response to this therapy. We present a case of a super-responder.

A Preclinical Trial Protocol Using an Ovine Model to Assess Scaffold Implant Biomaterials for Repair of Critical-Sized Mandibular Defects.

The present work describes a preclinical trial (in silico, in vivo and in vitro) protocol to assess the biomechanical performance and osteogenic capability of 3D-printed polymeric scaffolds implants used to repair partial defects in a sheep mandible. The protocol spans multiple steps of the medical device development pipeline, including initial concept design of the scaffold implant, digital twin in silico finite element modeling, manufacturing of the device prototype, in vivo device implantation, and in vitro laboratory mechanical testing. First, a patient-specific one-body scaffold implant used for reconstructing a critical-sized defect along the lower border of the sheep mandible ramus was designed using on computed-tomographic (CT) imagery and computer-aided design software. Next, the biomechanical performance of the implant was predicted numerically by simulating physiological load conditions in a digital twin in silico finite element model of the sheep mandible. This allowed for possible redesigning of the implant prior to commencing in vivo experimentation. Then, two types of polymeric biomaterials were used to manufacture the mandibular scaffold implants: poly ether ether ketone (PEEK) and poly ether ketone (PEK) printed with fused deposition modeling (FDM) and selective laser sintering (SLS), respectively. Then, after being implanted for 13 weeks in vivo, the implant and surrounding bone tissue was harvested and microCT scanned to visualize and quantify neo-tissue formation in the porous space of the scaffold. Finally, the implant and local bone tissue was assessed by in vitro laboratory mechanical testing to quantify the osteointegration. The protocol consists of six component procedures: (i) scaffold design and finite element analysis to predict its biomechanical response, (ii) scaffold fabrication with FDM and SLS 3D printing, (iii) surface treatment of the scaffold with plasma immersion ion implantation (PIII) techniques, (iv) ovine mandibular implantation, (v) postoperative sheep recovery, euthanasia, and harvesting of the scaffold and surrounding host bone, microCT scanning, and (vi) in vitro laboratory mechanical tests of the harvested scaffolds. The results of microCT imagery and 3-point mechanical bend testing demonstrate that PIII-SLS-PEK is a promising biomaterial for the manufacturing of scaffold implants to enhance the bone-scaffold contact and bone ingrowth in porous scaffold implants. MicroCT images of the harvested implant and surrounding bone tissue showed encouraging new bone growth at the scaffold-bone interface and inside the porous network of the lattice structure of the SLS-PEK scaffolds.

Driveline Infection in Patients With Left Ventricular Assist Devices Implanted as Destination Therapy

Donor organ shortages cause increasing demand for mechanical circulatory support in patients with end-stage heart failure not only as a bridge to heart transplantation but mainly as a destination therapy. Improved results and increased applicability and durability of left ventricular assist devices (LVADs) have established this treatment option as an alternative to heart transplantation in selected patients. One of the most common complications after LVAD implantation is driveline infections (DLIs). This study aimed to expand the understanding of DLI epidemiology and potential changes in implantation techniques regarding optimizing DLI prevention and treatment among all patients undergoing LVAD (Medtronic's Heartware HVAD and HeartMate 3 Abbott LVAD system) implantation with at least 12 months of follow-up time between 2015 and 2022. There were 120 individuals with LVAD implantation, of whom 90 had 12 months of follow-up (85 men [94%], 5 women [6%]) with a median age of 58 years (50.25-63.75). The median body mass index was 27.12 kg/m2 (25.27-29.68). Of the 90 patients, 43 had ischemic heart failure (48%), 43 had dilated cardiomyopathy (48%), and the remaining 3 had other etiologies (3%), such as postinflammatory, and the remaining 1 had congenital heart defect (1%). Preoperative echocardiography revealed a mean left ventricle ejection fraction of 13.8% and a median left ventricle dimension of 7.55 cm (6.92-8.2). Imaging confirmed pulmonary hypertension in 61 patients (68%). Thirty-four of the 90 patients had diabetes (38%), and 16 were active smokers (18%). Median follow-up was 30 months (17.25-42), with the longest period being 82 months. More than half of the patients (n = 52; 57%) experienced a DLI. The median time to the first episode of DLI was 13 months (6-25). The most common pathogen revealed in wound swab culture was methicillin-sensitive Staphylococcus aureus (n = 23; 44%), Pseudomonas aeruginosa (n = 9; 17%), Proteus mirabilis (n = 4; 7%), and others. We observed that deeper driveline implantation below the left rectus muscle and just above the posterior rectus sheath resulted in fewer DLIs and longer free-from-DLI follow-up time. There was no statistically significant difference in DLI frequency between patients with or without diabetes mellitus. Appropriate selection of candidates and timing of LVAD implantation are critical for improved outcomes of destination therapy. DLI is the most common complication after LVAD implantation. Optimal surgical techniques and early implementation of targeted antibiotics are crucial. Significant challenges remain in optimizing DLI prevention and treatment.

On the Ion Implantation Synthesis of Ag-Embedded Over Sr-Substituted Hydroxyapatite on a Nano-Topography Patterned Ti for Application in Acetabular Fracture Sites.

There is an ongoing need for improved healing response and expedited osseointegration on the Ti implants in acetabular fracture sites. To achieve adequate bonding and mechanical stability between the implant surface and the acetabular fracture, a new coating technology must be developed to promote bone integration and prevent bacterial growth. A cylindrical Ti substrate mounted on a rotating specimen holder was used to implant Ca2+, P2+, and Sr2+ ions at energies of 100 KeV, 75 KeV and 180 KeV, respectively, using a low-energy accelerator to synthesize strontium-substituted hydroxyapatite at varying conditions. Ag2+ ions of energy 100 KeV were subsequently implanted on the as-formed surface at the near-surface region to provide anti-bacterial properties to the as-formed specimen. The properties of the as-formed ion-implanted specimen were compared with the SrHA-Ag synthesized specimens by cathodic deposition and low-temperature high-speed collision technique. The adhesion strength of the ion-implanted specimen was 43 ± 2.3 MPa, which is well above the ASTM standard for Ca-P coating on Ti. Live/dead cell analysis showed higher osteoblast activity on the ion-implanted specimen than the other two. Ag in the SrHA implanted Ti by ion implantation process showed superior antibacterial activity. In the ion implantation technique, nano-topography patterned surfaces are not concealed after implantation, and their efficacy in interacting with the osteoblasts is retained. Although all three studies examined the antibacterial effects of Ag2+ ions and the ability to promote bone tissue formation by MC3T3-E1 cells on SrHA-Ag/Ti surfaces, ion implantation techniques demonstrated superior ability. The synthesized specimen can be used as an effective implant in acetabular fracture sites based on their mechanical and biological properties.

New frontiers in pacing: from myocardial pacing to conduction system pacing

For many years, cardiac pacing has been based on the stimulation of right ventricular common myocardium to correct diseases of the conduction system. The birth and the development of cardiac resynchronization have led to growing interest in the correction and prevention of pacing-induced dyssynchrony. Many observational studies and some randomized clinical trials have shown that conduction system pacing (CSP) can not only prevent pacing-induced dyssynchrony but can also correct proximal conduction system blocks, with reduction of QRS duration and with equal or greater effectiveness than biventricular pacing. Based on these results, many Italian electrophysiologists have changed the stimulation target from the right ventricular common myocardium to CSP. The two techniques with greater clinical impact are the His bundle stimulation and the left bundle branch pacing. The latter, in particular, because of its easier implantation technique and better electric parameters, is spreading like wildfire and is representing a real revolution in the cardiac pacing field. However, despite the growing amount of data, until now, the European Society of Cardiology guidelines give a very limited role to CSP.

Percutaneous Mechanical Circulatory Support in Acute Heart Failure Complicated with Cardiogenic Shock.

Despite advancements in algorithms concerning the management of cardiogenic shock, current guidelines still lack the adequate integration of mechanical circulatory support devices. In recent years, more and more devices have been developed to provide circulatory with or without respiratory support, when conservative treatment with inotropic agents and vasopressors has failed. Mechanical circulatory support can be contemplated for patients with severe, refractory, or acute-coronary-syndrome-related cardiogenic shock. Through this narrative review, we delve into the differences among the types of currently used devices by presenting their notable advantages and inconveniences. We address the technical issues emerging while choosing the best possible device, temporarily as a bridge to another treatment plan or as a destination therapy, in the optimal timing for each type of patient. We also highlight the diverse implantation and removal techniques to avoid major complications such as bleeding and limb ischemia. Ultimately, we hope to shed some light in the gaps of evidence and the importance of conducting further organized studies around the topic of mechanical circulatory support when dealing with such a high mortality rate.

Salvage procedures for infected penile implants: A comprehensive review and analysis of functional outcomes

BackgroundThe salvage procedure for infected penile implants (IPs) has been a subject of interest since its inception in the late 1980s, yet its widespread adoption remains limited. The aim of this study was to realize a systematic literature review to provide a comprehensive analysis of salvage techniques for IPs and assess their efficacy, specifically focusing on functional success. MethodsA systematic literature review was conducted using PubMed, employing Mesh terms related to penile prosthesis, penile implant, infection, and salvage procedures. Articles in French or English were considered for the final analysis, with exclusion of literature reviews. ResultsFifteen articles detailing various salvage techniques for IPs were identified. Mulcahy's initial technique was described in 1996, and consisted of complete removal of infected components, extensive lavage, and subsequent replacement with a similar implant. Success rates ranged from 80% to 100%, with emerging trends favoring the use of malleable implants during salvage. Unfortunately, functional data remained limited. When salvage penile prosthesis placement involved a malleable prosthesis, between 20% and 33% of patients underwent conversion to hydraulic prosthesis. ConclusionThe salvage procedure for infected penile implants is a reliable method, with success rates surpassing 80%. The need for comparative studies assessing the type of implant used during salvage is required to tailor conservative management strategies for optimal patient outcomes. Finally, few data have been published regarding subsequent conversions from malleable penile implants to hydraulic penile implants after salvage.

Efficacy and safety analysis of scleral fixation intraocular lens implantation using the Yamane technique

Introduction: Cataract surgery technologies continue to manage complications. Current surgical methods for secondary Intra Ocular Lens (IOL) include Anterior Chamber IOL, Iris Claw IOL, and sutured and sutureless techniques of Scleral Fixation IOL (SFIOL). The Yamane technique of SFIOL is a novel, relatively safe, and easy method of sutureless SFIOL. This study aims to describe and analyze the surgical outcomes and complications of the Yamane IOL implantation technique. Methods: A retrospective study of 21 eyes of 21 patients that underwent scleral fixation of IOL by the Yamane technique was observed. Demographic data, primary indications for surgery, best corrected visual acuity (BCVA), intraocular pressure (IOP) pre-operative and post-operative during follow-up, and complications were also analyzed. Results: Twenty-one patients were included, with an average age of 52.57±23.41 years old. Eleven eyes with lens subluxation (52.4%), 9 eyes with aphakia (42.9%), and 1 eye with phacodonesis (4.8%) were indicated for the Yamane technique of SFIOL in this study. The preoperative mean BCVA was 2.2±0.9 LogMAR, while the 1-month postoperative BCVA was 1.1±0.9 LogMAR. The mean preoperative IOP was 15.81±6.7 mmHg, and the 1-month postoperative IOP was 16.00±7.7 mmHg. This study found that there was a significant improvement in BCVA with p=0.00 (p&lt;0.05), and there was no significant postoperative IOP spike with p=0.88 (p&lt;0.05). The main complications observed in this study were corneal edema (23.8%) and postoperative IOP spike (14,3%). Conclusion: The Yamane SFIOL technique is a relatively safe approach for the surgical management of patients who need secondary IOL implantation with significantly improved visual function without significant complications.

Titanium Surface Modification Techniques to Enhance Osteoblasts and Bone Formation for Dental Implants: A Narrative Review on Current Advances

Surface modifications for titanium, a material of choice for dental implants, can greatly alter the surface micro/nanotopography and composition of implants, leading to notable enhancements in their hydrophilicity, mechanical properties, osseointegration performance, and antibacterial performance, as well as their impacts on osteoblast activity and bone formation processes. This article aims to update titanium surface modification techniques for dental implants from the past to the present, along with their effects on osteoblasts and bone formation, by thoroughly summarizing findings from published studies. Peer-reviewed articles published in English consisting of in vitro, in vivo, and clinical studies on titanium dental implant surface treatments were searched in Google Scholar, PubMed/MEDLINE, ScienceDirect, and the Scopus databases from January 1983 to December 2023 and included in this review. The previous studies show that implant surface roughness, condition, and hydrophilicity are crucial for osteoblast adhesion and growth. While various techniques enhance osseointegration comparably, one of the most common approaches to accomplishing these properties is sandblasting large-grit acid etching surface treatment and coating with hydroxyapatite or chitosan. In conclusion, this review points out the efficacy of different subtraction and addition techniques in enhancing the surface properties of titanium dental implants, promoting favorable outcomes in terms of osteoblast activity and bone formation in various degrees. However, most existing studies predominantly compare treated and non-treated titanium, revealing a need for more comprehensive studies comparing the effects of various modification techniques. Moreover, further investigation of factors playing a role in the dynamic osseointegration process in addition to osteoblasts and their functions, as well as improved surface modification techniques for the treatment of compromised patients, is greatly required.

Enhancing the implantation of mechanical circulatory support devices using computational simulations.

Introduction: Patients with end-stage heart failure (HF) may need mechanical circulatory support such as a left ventricular assist device (LVAD). However, there are a range of complications associated with LVAD including aortic regurgitation (AR) and thrombus formation. This study assesses whether the risk of developing aortic conditions can be minimised by optimising LVAD implantation technique. Methods: In this work, we evaluate the aortic flow patterns produced under different geometrical parameters for the anastomosis of the outflow graft (OG) to the aorta using computational fluid dynamics (CFD). A three-dimensional aortic model is created and the HeartMate III OG positioning is simulated by modifying (i) the distance from the anatomic ventriculo-arterial junction (AVJ) to the OG, (ii) the cardinal position around the aorta, and (iii) the angle between the aorta and the OG. The continuous LVAD flow and the remnant native cardiac cycle are used as inlet boundaries and the three-element Windkessel model is applied at the pressure outlets. Results: The analysis quantifies the impact of OG positioning on different haemodynamic parameters, including velocity, wall shear stress (WSS), pressure, vorticity and turbulent kinetic energy (TKE). We find that WSS on the aortic root (AoR) is around two times lower when the OG is attached to the coronal side of the aorta using an angle of 45° ± 10° at a distance of 55mm. Discussion: The results show that the OG placement may significantly influence the haemodynamic patterns, demonstrating the potential application of CFD for optimising OG positioning to minimise the risk of cardiovascular complications after LVAD implantation.

Application of pocket-first technique for implantation of totally implantable venous access ports.

While vascular puncture is always performed before making port pocket in the implantation of totally implantable venous access ports (TIVAP), some surgeons preferred to make port pocket first. This study seeks to verify the safety and feasibility for the pocket-first technique. The study retrospectively reviewed 447 patients who undergone TIVAP implantation from July 2017 to November 2022. All the patients were divided into two groups based on vascular puncture first or making port pocket first. The general information, operation information and post-operative complications were reviewed and analyzed. All the operations were performed successfully. No difference was observed in the sex, age, height, weight, BMI, port location and total complication rate between the two groups. The operation time of the Puncture Group and the Pocket Group were 46.9 ± 22.4min and 33.8 ± 13.6min ( P<0.00001 ). In the patients of SCV approach, the operation time between the two groups were 37.4 ± 14.8min and 33.5 ± 10.9min ( P<0.05 ). Multivariate analysis showed the variable BMI and first procedure were independent prognostic factors for operation time. In the cases using SCV/AxV approach the variable first procedure was the only independent prognostic factor for operation time (P = 0.002). The pocket-first technique can be considered as a safe, feasible and convenient technique for TIVAP implantation. The time consuming is significantly shortened compared with the puncture-first technique and this advantage may be more obvious when using SCV/AxV approach.

Paravalvular regurgitation after transcatheter aortic valve replacement: incidence, quantification, and prognostic impact.

Transcatheter aortic valve replacement (TAVR) is the standard of care in aortic stenosis with results comparable to surgical aortic valve replacement. However, paravalvular regurgitation (PVR) is more common after TAVR. With the alteration of devices and implantation techniques, the incidence of moderate or more PVR has declined. Mild PVR is still common in around 30% of TAVR patients in low-risk trials. Progression of AS causes myocardial hypertrophy and varying degrees of diastolic dysfunction which may cause heart failure even in combination with small volumes of PVR. Any degree of PVR is associated with an increased risk of overall and cardiovascular mortality. Predictors of PVR are annular eccentricity, severe calcification of the aortic valve, bicuspid aortic valves, and type of prosthesis where balloon-expandable devices are associated with less PVR. PVR is diagnosed using echocardiography, aortic angiogram with or without videodensitometry, haemodynamic parameters, or cardiac magnetic resonance. PVR can be treated using post-dilation, interventional treatment using a vascular plug, or implantation of a second device. Successful post-dilation depends on balloon size which should at least be equal to or >95% of the mean annulus diameter. Implantation of a second device to reduce PVR is successful in ∼90% of cases, either through lengthening of the sealing skirt in case of inadequate position or through further expansion of the index device. Implantation of a vascular plug can successfully reduce PVR and reduce mortality.

Autologous chondrocyte implantation for the treatment of osteochondral lesions of the talus: What happens after 20 years?

BackgroundThe purpose of this study was to assess the long-term clinical efficacy of first-generation autologous chondrocyte implantation (ACI) technique for osteochondral lesions of the ankle joint. MethodsEleven patients with symptomatic OLTs underwent ACI from December 1997 to October 2002. A total of 9 patients (5 men, 4 women, age 25.2 ± 6.3) were evaluated at baseline and at 1, 3, 10 years, and at final follow-up of minimum 20 years with AOFAS ankle-hindfoot score, NRS for pain, and with the Tegner score. ResultsThe AOFAS score improved significantly from the baseline value of 40.4 ± 19.8 to 82.7 ± 12.9 at the final follow-up (p < 0.0005). The NRS for pain improved significantly from 7.8 ± 0.7 at baseline to 4.8 ± 2.1 at the final follow-up (p < 0.0005). Moreover, the Tegner score underwent a modification from the pre-operative median value of 1 (range: 1–3) and from a pre-injury value of 5 (range: 3–7) to 3 (range: 2–4) at the final follow-up (p < 0.0005). ConclusionsACI has proven to be an effective treatment option for patients suffering from OLTs, leading to a long-lasting clinical improvement even beyond 20 years of follow-up. Level of evidenceLevel IV

Tumor promoting effect of spheroids in an orthotopic prostate cancer mouse model.

In this study, we aimed to establish a technique for intraprostatic implantation of prostate cancer (PCa) spheroids and to identify the impact of three-dimensional organization of PCa cells on tumor progression and metastasis in a representative in vivo model. 40,000 LNCaP cells were implanted into the prostate of immunodeficient SCID mice either as single cells (n = 8) or as preformed 3D spheroids (n = 8). For a follow up of 20weeks, tumor growth was monitored by serum PSA and high-resolution 3D ultrasonography. Eventually, animals were sacrificed and autopsied. The organ dissects were analyzed for the presence of metastases by histology (H&E) and immunohistochemistry (AMACR, AR, Ki-67, CK5, CK8, E-Cadherin, Vimentin). Solid intraprostatic tumors developed in 50% of mice after spheroid implantation and in 50% of mice after implantation of a single cells. Primary tumors of LNCaP spheroids evolved earlier, exhibiting a shorter tumor doubling time whilst developing larger tumor volumes, which was reflected by a higher immunohistochemical expression of Ki-67 and AR, too. Spheroid tumors established lung and lymph node metastases in 75% of mice, in contrast to 50% of mice after single cell implantation. Our technique enables a variety of studies regarding the influence of the tumor microenvironment on PCa progression.

New autologous fat implantation technique for face lifting: A pilot study.

Autologous fat injection techniques are specially performed to restore the lack of face volume. However, no reports have focused on the effect of sides of injection on the sagging appearance improvements and facial lifting. This study aimed to evaluate face lifting using the autologous fat injection in to sides of the face as a new technique. Ten patients with aging face were involved in this study. The procedure was done in an anaerobic method. To improve the method, to make patients more satisfied and gain better cosmetic outcomes autologous fat was injected on the sides of the face. To give a lifting effect to the face, the fat was injected on the hairline in the temple area, next to the ear, the angel of the jaw and the angel of the mandible leaning behind the ear to cause face lift. The patients were appraised clinically and photographically. The results showed that this autologous fat injection technique has significant improvement in face lifting. This new fat injection technique in sides of the face can create superior results on face lifting without any adverse side effects.

A Spectrum of Chemoport-Associated Complications and Their Management in Cancer Patients.

Chemotherapy is part and parcel of the multimodality approach to cancer treatment. Chemoports are frequently used to administer chemotherapy, preventing complications associated with the use of peripheral lines. However, chemoports have their own set of complications and can be very debilitating at times. Accurate knowledge and correct technique can help prevent and manage these complications properly. We retrospectively analyzed all patients who underwent chemoport insertion for chemotherapy infusion over three years between July 2020 and June 2023. The patient's profile, type of cancer, the technique of chemoport insertion, complications related to chemoport, and its management were recorded retrospectively from patient records. The total number of patients in our study was 119. The age group of patients ranged from 13 years to 76 years. Of the 119 patients, 55 had breast cancer, 23 had ovarian cancers, 29 had GI cancers including gastroesophageal junction (GEJ)/ stomach/periampullary/colorectal, and 12 had leukemias. The most common intraoperative complication was catheter tip malposition (9.2%). The most common postoperative complications were infection (7.5%), followed by drug extravasation (5.0%), thrombosis (3.3%), wound dehiscence (2.5%), and skin necrosis (0.8%) in decreasing order of frequency. Serious complications such as hemothorax, pneumothorax, air emboli, brachial plexus injury, and pericardial tamponade, commonly reported in the literature, were not seen in any of our cases. Totally implanted venous access devices (TIVAD)/chemoports are indispensable in the management of cancer patients, especially in patients requiring long duration of infusion and prolonged treatment. Although chemoports are associated with a spectrum of complications, proper technique of implantation and use makes it a safe and reliable tool.

Biomimetic approach to the design of artificial small‑diameter blood vessels

Objective: To create 2-mm diameter multilayer porous tubular scaffolds (PTS) with characteristics that resemble small-diameter native blood vessels in terms of characteristics.Materials and methods. PTS made of polycaprolactone (PCL, MM 80000) with a PCL-made sealing coat/layer with gelatin addition (PCL-gelatin) with a diameter of 2 mm were created by electrospinning (NANON-01A). Bioactive coating was applied to the PTS surface by sequential incubation in solutions of bovine serum albumin, heparin (Hp), and platelet lysate (PL). Cytotoxicity was investigated under conditions of direct contact of PTS with a monolayer of NIH/3T3 mouse fibroblasts. Viability of human umbilical vein endothelial cells (EA.hy926) was evaluated using Live/Dead® Viability/Cytotoxicity Kit. Permeability and blood flow parameters of the PTS implanted in the infrarenal section of the rat aorta were recorded using Doppler imaging.Results. A three-layer PTS construct with an inner diameter of 2 mm was developed. Its inner and outer layers were formed from 0.2 mL of PCL solution, and the middle sealing coat/layer was from 0.5 mL of PCL with addition of 30% (by weight of polymer) gelatin. Introduction of the sealing coat/layer reduced surgical porosity (SP) from 56.2 ± 8.7 mL/(cm2·min) for a single-layer PTS made of pure PCL to 8.9 ± 2.6 mL/(cm2·min) for a three-layer PTS. The resulting PTS demonstrated physicomechanical characteristics similar to those of native blood vessels; it also showed no cytotoxicity. Application of a bioactive coating of Hp and PL allowed for increased in vitro adhesion and proliferation of endothelial cells. The technique of implantation of 10 mm long fragments of three-layer PTS into the infrarenal section of a rat aorta was corrected, thus minimizing blood loss and narrowing the anastomosis site. In an acute experiment, it was proven that the prostheses were patent and that blood flow parameters (systolic and diastolic velocity, resistivity index) were close to the corresponding indicators of native rat aorta.Conclusion. The developed three-layer PTS constructs have low SP and physicomechanical properties close to those of native blood vessels. Bioactive coating improves the in vitro matrix properties of PTS relative to human endothelial cells. At short-term implantation into the aorta of experimental animals, PTS showed no early thrombosis, while blood flow parameters were close to those of native rat aorta. Thus, three-layer PTS with bioactive coating can be used as a scaffold for creation of in situ tissue-engineered construct of a small-diameter blood vessel.