Neutron Imaging Research Articles

The importance of the adiabatic condition on polarized neutron imaging

Polarized neutron imaging has many applications through characterization of magnetic fields generated from currents or magnetic moments. If local magnetic field directions change slowly relative to its precession frequency, the angle between neutron polarization vector and the local field vector remains constant. Conversely, if the fields change rapidly relative to the precession frequency, this angle may vary. The transition between these scenarios follows the adiabatic condition. In this study, we analyze the effects of the adiabatic condition on a polarized neutron image. Two case studies are used for illustrating possible scenarios. The first case shows how an external field, due to the adiabatic condition, influences the symmetry of a polarized neutron image of a current carrying solenoid. The second case study shows how the adiabatic coupling of the beam polarization could lead to the loss of contrast in a polarized neutron image while studying field penetration in type II superconductors. Both case studies serve to highlight the importance of taking this phenomenon into account while interpreting polarized neutron imaging data given the rising importance of the technique as a characterization method in magnetism and superconductivity research.

Phase-contrast neutron imaging compared with wave propagation and McStas simulations

Propagation-based phase contrast, for example in the form of edge enhancement contrast, is well established within X-ray imaging but is not widely used in neutron imaging. This technique can help increase the contrast of low-attenuation samples but may confuse quantitative absorption measurements. Therefore, it is important to understand the experimental parameters that cause and amplify or dampen this effect in order to optimize future experiments properly. Two simulation approaches have been investigated, a wave-based simulation and a particle-based simulation conducted in McStas [Willendrup & Lefmann (2020). J. Neutron Res. 22, 1–16], and they are compared with experimental data. The experiment was done on a sample of metal foils with weakly and strongly neutron absorbing layers, which were measured while varying the rotation angle and propagation distance from the sample. The experimental data show multiple signals: attenuation, phase contrast and reflection. The wave model reproduces the sample attenuation and the phase peaks but it does not reproduce the behavior of these peaks as a function of rotation angle. The McStas simulation agrees better with the experimental data, as it reproduces attenuation, phase peaks and reflection, as well as the change in these signals as a function of rotation angle and distance. This suggests that the McStas simulation approach, where the particle description of the neutron facilitates the incorporation of multiple effects, is the most convenient way of modeling edge enhancement in neutron imaging.

A lithium ore grade measurement based on the neutron & X-ray bi-modal imaging system

The grades of the minerals significantly affects the energy consumption and chemical pollution along with the beneficiation process for extracting lithium element from the ores. Based on the large neutrons’ macro cross section of the Li2O cluster inside the ores, the grades of lithium ores could be analyzed by the thermal neutron penetrating information. In this work, a bimodal imaging method, which utilizes both the information of penetrating neutrons and X-rays delivered by the same electron linear accelerator driven photoneutron system, was proposed to investigate the lithium concentration of each ore. A linearity R-square value of 0.991 between the results obtained with this method and those from the chemical method has been achieved. The average error in lithium concentration estimation is approximately 0.2 wt percent (wt%). The underlying principles and the experimental results will be elaborated on in this study.

Investigation of Li accumulations in LLZO based solid state batteries via operando neutron imaging and ex-situ correlative structural and chemical analysis

In this study, we present a comprehensive analysis of lithium dendrite formation in half-cells with lithium garnet-type solid-state electrolyte Li7La3Zr2O12 (LLZO) utilizing operando neutron imaging and subsequent ex-situ correlative structural and chemical analysis. The operando experiment involves cycling a solid-state symmetric half-cell (Li|LLZO|Li) until short-circuit failure, all while being irradiated with neutrons, providing invaluable insights into the dynamic processes within the symmetric half-cell. Post-mortem investigations were carried out, comprising two techniques: 1) secondary electron imaging for structural analysis and 2) secondary ion mass spectrometry (SIMS) for chemical mapping. This multifaceted approach creates complementary datasets, bridging the gap between neutron radiography, known for its quantitative transmission capabilities, and high-resolution, high-sensitivity structural and chemical imaging via scanning electron microscopy (SEM) and SIMS.Central to our investigation is the design and development of an operando neutron imaging approach, enabling the study of lithium penetration during the electrochemical cycling. Furthermore, structural, and chemical analyses through correlative SEM/SIMS unveil various morphologies of lithium accumulations. Specifically, regions with dense LLZO reveal intergranular lithium accumulations, while low-density areas within the LLZO pellet, such as pores and cracks, exhibit distinct types of lithium accumulations (e.g. whiskers).Notably, neutron analysis reveals an accumulation of lithium in selected regions, with a maximum increase of up to 3.6 vol.-%. These regions primarily correspond to the roughened LLZO/Li interface, as observed through neutron imaging, although the SEM/SIMS analysis unequivocally confirms the presence of lithium dendrites (with sizes at or below the resolution limit of neutron imaging) also within the bulk of LLZO.This work offers a comprehensive examination of the intricate dynamics of lithium dendrite formation and behaviour in LLZO-based solid-state half-cells, emphasizing the potential of operando techniques to advance our understanding of critical issues (e.g. degradation, dendrite formation, …) in battery research.

Thermal deflection in neutron scattering sample environments at Oak Ridge National Laboratory.

The neutron sources at Oak Ridge National Laboratory use a wide suite of sample environment equipment to deliver extreme conditions for a number of experiments. Much of this instrumentation focuses on extremes of temperature, such as cryostats, closed-cycle refrigerators in both low and high temperature configurations, and radiant heating furnaces. When the temperature is controlled across a large range, thermal deflection effects can notably move the sample and affect its alignment in the beam. Here, we combine these sample environments with neutron imaging and machine vision to determine the motion of a representative sample with respect to the neutron beam. We find vertical sample displacement on the order of 1-2mm and horizontal displacement that varies from near-negligible to 1.2mm. While these deflections are not relevant for some of the beamlines at the first target station at the spallation neutron source and the high flux isotope reactor, they will become critical for upcoming instrumentation at the second target station, as well as any instruments targeting sub-mm samples, as neutron sources and optics evolve to smaller and more focused beams. We discuss mitigation protocols and potential modifications to the environment to minimize the effect of misalignment due to thermal deflection.

Imaging of low Z masked with high Z (Pb, U) materials using 14 MeV neutron

An experimental study has been performed using 14 MeV neutrons for imaging of low Z material (particularly composed of C, H, O elements) masked with thick layers of dense and high Z materials. The experimental setup consists of a D-T neutron generator, a metallic collimator and an imaging system. The imaging system is designed with a polypropylene zinc sulphide scintillator screen integrated with a lens coupled 16-bit ICCD camera. Imaging capability of the system was investigated using iron test samples with holes and line pair features. The minimum hole size of 2 mm could be imaged at a contrast of 36% and a line of 2 mm width visible at a contrast of 24% indicating the system's resolution of ∼ mm. Low Z samples such as water (H2O) and polyethylene (C2H2) n placed behind thick layers of Pb (40 mm) and Uranium (35 mm), were imaged successfully. These images reveal the system's ability towards low Z material imaging in the presence of heavier metals. Good contrast images acquired at a lower neutron yield of ∼ 5 × 108 n/sec of D-T neutron generator has provided a possibility to realise fast neutron imaging having moderate resolution (∼ mm) with a smaller footprint and an economical system design for field applications.

Spot size measurement of a deuterium-tritium dense plasma focus using neutron radiography.

Neutron radiography is a technique uniquely suited to applications in nuclear diagnostics, non-destructive testing, and subcritical experiments. The spatial resolution of neutron radiographs is degraded by optical blur in the imaging system and the neutron source size, where the ideal source is point-like to optimize the point-spread function. A potential neutron source for radiography is the dense plasma focus (DPF), a coaxial Z-pinch that produces thermonuclear and beam-target neutrons. To assess if the source size is suitable for radiography, a neutron imaging system was used to measure the source size of the 4 MA Sodium DPF at the Nevada National Security Site operating with deuterium-tritium gas-fill. The source size was measured using the edge-spread function of tungsten objects, each having a rolled (convex) edge. The spot size was found to be 7-12mm full-width at half-max(FWHM) assuming a Gaussian source, though comparison is presented for Lorentzian and Bennett distributions. The average FWHM was found to be 8.6 ± 1.2mm vertically and 10.8 ± 1.2mm horizontally with respect to the image plane, averaging over varied edges and alignments. The results were sensitive to source alignment and edge metrology, which introduced notable uncertainties. These results are consistent with separate experimental measurements as well as magnetohydrodynamics simulations of this DPF, which suggest that neutron production can originate from pinches ∼5-7mm off-axis. These results suggest that the DPF should be used for radiography at low magnification (M < 1) where spot size does not dominate spatial blur.

Optimization design for moderator, reflector, and shielding of Deuterium-Deuterium neutron source

Deuterium-Deuterium (D-D) neutron source, which could be used in both laboratory and outdoors due to its light weight, small volume and low cost, has been widely applied in thermal neutron imaging (TNI) and prompt gamma-ray neutron activation analysis (PGNAA). And the its optimization design is to obtain highly intense thermal neutrons and low dose rate around the facility with light weight and compact volume. In this paper, the genetic algorithm (GA) combined with MCNP6 was applied to globally optimize moderator, reflector, and shielding structures. As a result, the optimized thermal neutron intensity increased by 1.68 times, while the dose rate, weight and volume respectively decreased by 37%, 52%, and 27%, compared with the data based on the current design. This method could be an effective tool for the compact neutron source design.

Quantitative Analysis of Active Lithium Loss and Degradation Mechanism in Temperature Accelerated Aging Process of Lithium‐Ion Batteries

AbstractQuantifying the aging mechanisms and their evolution patterns during battery aging is crucial for enabling renewable energy. Here, key factors are monitored and quantified affecting the aging processes of LiFePO4//graphite battery by a combination of mass spectrometry titration (MST), nuclear magnetic resonance (NMR), cryogenic transmission electron microscopy (cryo‐TEM), and neutron imaging techniques. Electrochemical analysis reveals the loss of active lithium inventory drives battery aging as temperature increases. It is shown that temperature‐induced accelerated decaying rate is 2.01 and 3.45 times at 45 and 65 °C compared with that of rate at 25 °C. Quantitative analysis indicates that irreversible formation of LixC6 (x ≤ 1), LiF, ROCO2Li, LiH, Li2C2, and RLi (R = CH3, C2H3, C2H5, C3H5) are the primary components of inactive lithium. The solid eletrolyte interpahse (SEI), excluding LixC6, constitutes over 70% of the total inactive lithium. With increasing cycles, SEI shows a decreasing proportion of LiF and an increasing proportion of ROCO2Li. The coupled effects of substantial SEI growth, increased irreversible formation of LixC6, and worsened conductivity result in the rapid aging of batteries tested at high temperatures. In this work, a research toolbox for the quantitative study of aging mechanisms in practical batterysystems has been provided.

Towards in-situ water quantification via neutron imaging: insights from NeXT-Grenoble

Neutron imaging has gained increasing attention in recent years. A notable domain is the in-situ study of flow and concentration of hydrogen-rich materials. This demands precise quantification of the evolving concentrations. Several implementations deviate from the ideal conditions that allow the direct applicability of the Beer–Lambert law to assess this concentration. The objective of this work is to address these deviations by applying both calibration and correction procedures to ensure and validate accurate quantitative measurements during 2D and 3D neutron imaging conducted at the cold neutron source at the NeXT instrument of the Institute Laue–Langevin, Grenoble, France. Linear attenuation coefficients and non-linear correlations have been proposed to measure the water concentration based on the sample-to-detector distance. Furthermore, the effectiveness of the black body grid correction method, introduced by Boillat et al (2018 Opt. Express 26 15769), is evaluated which accounts for spurious deviations arising from the scattering of neutrons from the sample and the surrounding environment. The applicability of the Beer–Lambert law without any data correction is found to be reasonable within limited equivalent thickness (e.g. below 4 mm of water) beyond which the correction algorithm proves highly effective in eliminating spurious effects. Notably, this correction method maintains its effectiveness even with transmissions below 1%. We examine here the impact of grid location and resolution with respect to sample heterogeneity.

Sparse-View Neutron Computed Tomography 3-D Reconstruction via the Fast Gradient Projection Algorithm

Neutron tomography is an efficient nondestructive testing technique. As a complement to X-ray computed tomography, it has been widely used in various fields. Due to the difficulty of obtaining complete neutron projection data in a high-radiation environment and the high noise characteristics of neutron images, it is difficult to reconstruct a high-quality image using the conventional filtered-back projection (FBP) algorithm. Therefore, research on sparse-view reconstruction algorithms in neutron tomography is needed. To improve the quality of neutron three-dimensional reconstructed images, this paper proposes an algorithm that combines the Simultaneous Algebraic Reconstruction Technique (SART) with Fast Gradient Projection (FGP), where the FGP is an algorithm for image denoising and deblurring based on the discrete total variation (TV) minimization model. The algorithm proposed in this paper is compared with other algorithms (FBP, SART, and SART-TV) by simulated experimental data and real neutron experimental data. The experimental results show that the novel algorithm outperforms the other three algorithms in terms of denoising and retaining detailed structural information.

Neutron instrument concepts for a high intensity moderator at the European spallation source

In the course of the Horizon 2020 project HighNESS, a second moderator concept has been developed for the European Spallation Source, which complements the currently built moderator and is optimized for high intensity with a large viewable surface area. In this work we introduce conceptual designs for neutron instruments for condensed matter research designed to make optimal use of the capabilities of this moderator. The focus is on two concepts for small-angle neutron scattering and one neutron imaging instrument, which are intended to complement corresponding instruments that are already under construction at the European Spallation Source. One small-angle neutron scattering instrument concept resembles a conventional pinhole collimator geometry and aims to profit from the proposed second moderator by enabling to illuminate larger samples and providing particularly high resolution, drawing on a 30 m collimation and corresponding detector distance. A second small-angle neutron scattering instrument concept adopts nested mirror optics that enable to efficiently exploit the large moderator size and provide high resolution by focusing on the detector. The neutron imaging instrument concept is a typical pinhole instrument that can be found at continuous sources and draws on the corresponding strengths of high flux and large homogeneous fields-of-view, while still providing moderate wavelength resolution for advanced imaging methods.

Characterization of 17th century archaeological metallic statuettes using combined neutron tomography and neutron diffraction

A combination of neutron computed tomography and neutron diffraction analysis has been studied to demonstrate the efficacy of employing neutron-based methodologies to investigate brass metallic statuettes, thereby shedding light on their structural and phase characteristics, all the while obviating the need to dissect the sample physically. In order to corroborate the findings obtained from the neutron-based techniques, supplementary methodologies such as Energy Dispersive X-ray Fluorescence were employed to extract elemental information and validate the results. These preliminary findings draw attention to the potential of neutron imaging to unveil intricate information regarding the techniques and components employed by artisans of antiquity in the production of Indian brass artifacts. We were also able to discern concealed structural attributes within metallic statuettes, as well as ascertain the precise phase composition of the brass alloy, thus further enriching our understanding of manufacturing practices of brass statuettes in the 17th-century era.

Water management and mass transport of a fractal metal foam flow-field based polymer electrolyte fuel cell using operando neutron imaging

Metal foam flow-fields (MFFs) exhibit immense potential for enhancing the performance of polymer electrolyte fuel cells (PEFCs) owing to their advantageous pore connectivity and abundant gas pathways. Nevertheless, challenges remain with the conventional MFF concerning reactant homogeneity and water management. To address these concerns, this study incorporates a fractal manifold into the MFF design. By employing operando neutron imaging, device-level testing, and electrochemical impedance spectroscopy (EIS), a comprehensive understanding of mass transfer and water management characteristics across the fractal manifold MFF is obtained. This novel design delivers better cell performance and lower mass transport resistance compared to the conventional MFF under all experimental conditions investigated. Notably, neutron imaging reveals that the fractal manifold MFF consistently exhibits a reduced liquid water content and more uniformly distributed liquid water compared to the conventional MFF. These superior characteristics of the design contribute to a substantial ∼15% increase in maximum power density compared to the conventional MFF-based PEFC. The results indicate the potential for further performance improvement by optimizing manifold parameters.

Dual particle imaging: Applications in security and environmental imaging

Radiation imaging detectors have been applied in a variety of fields for detection, localization and characterization of radioactive sources. In this work, we describe a handheld detection system (H2DPI) that can simultaneously image neutrons and gamma rays, and reconstruct the energy spectra of the incident particles. This system was applied to the detection and characterization of a plutonium metal source in experiments performed at the National Criticality Experiments Research Center, where the 4.5 kg plutonium source was placed approximately 60 cm from the H2DPI. Neutron and gamma-ray images were measured that show good agreement with the known location of the source. Furthermore, the H2DPI was also used to measure the neutron spectrum, which shows the expected shape of a Watt fission spectrum, and the gamma-ray energy spectrum, which shows the energies common to plutonium metal. Lastly, we describe the application of the H2DPI in augmented reality, whereby real-time neutron and gamma-ray imaging data can be streamed to the Microsoft HoloLens to allow the user to visualize the source locations.

Who made the noise? Systematic approach for the assessment of neutron imaging scintillators

We propose a method to analyze the characteristics of scintillator screens for neutron imaging applications. Using calculations based on the theory of cascaded linear steps as well as experimental measurements, we compared the characteristics of different lithium- and gadolinium-based scintillator screens. Our results show that, despite their much lower light output, gadolinium-based scintillators outperform lithium-based scintillators in terms of noise characteristics for a variety of imaging setups. However, the relative performance of scintillator screens is highly dependent on the other setup characteristics such as the beam spectrum, field of view, used optical lens and size of the camera sensor. Consequently, the selection of the best scintillator screen – as well as the scintillator characteristics assessment in new developments – requires a systematic consideration of all these elements, as enabled by the framework presented here.

3D Reconstruction and Nuclear Analytical Investigations of Tropaeum Traiani Monument, Adamclisi

Abstract The paper aims to conduct a novel investigation of ceramic samples from the Trophaeum Traiani Monument in Romania using various nuclear analytical techniques such as WDXRF, XRD, neutron diffraction, and neutron tomography, which will be complemented by FTIR and Raman spectroscopy data. The experimental data gathered revealed the mineral and chemical composition of the object’s surface, identifying quartz, hematite, calcite, and graphite. The employment of non-destructive techniques with high penetration capabilities is adequate in examining the spatial distribution and phase composition of the samples, providing valuable insights into their composition and structure without altering their integrity.

Understanding water dynamics in operating fuel cells by operando neutron tomography: investigation of different flow field designs

Water management plays a key role in ensuring optimum polymer electrolyte fuel cell (PEFC) performance, and flow field design can influence the ability of a cell to balance maintaining hydration, whilst avoiding flooding and cell failure. This work deepens the understanding of water evolution in different PEFC flow channel designs, namely single serpentine (SS), double serpentine (DS) and parallel, using our novel high-speed neutron computed tomography method. We developed our previously-reported method by introducing continuous cell rotation, enabling 18 s per tomogram during 1 h holds at 300, 400 and 500 mA cm−2. The volume of water evolved in the cathode, membrane electrode assembly and anode was quantified, and key mechanisms for water droplet formation in the different flow channel designs were elucidated. The parallel flow field design had the poorest water management, with 47% of the cathode flow channel becoming filled after 1 h at 400 mA cm−2. This significant flooding blocked reactant sites and contributed to unstable cell performance and, ultimately, cell failure at higher current densities. The SS cell displayed the best water management, with only 11% of the cathode channel filled with water after 1 h at 500 mA cm−2, compared with 28% of the DS cathode channel. 3D visualisation and analysis of droplet behaviour elucidated how water ‘slugs’ in the SS were removed in the gas stream, whereas three of the four parallel cathode flow channels became entirely filled with water plugs, blocking gas flow and exacerbating cell flooding. The new insights gained here are expected to extend to novel flow field designs and image-based models, with the use of operando neutron CT demonstrated as a powerful technique for both visualising and quantifying water management in operating PEFCs, as well as deepening the knowledge of droplet behaviour in different flow field types.

Experimental and Modeling Analyses of the Correlation between Local 3D Heterogeneities and the Macroscopic Observers of a Proton Exchange Membrane Fuel Cell Stack

In this study, we offer a complete investigation of a high-performing Proton Exchange Membrane Fuel Cell stack customized for automotive use. Our approach goes beyond traditional global electrochemical performance metrics such as polarization curves, ohmic resistance. Instead, we utilize specialized segmented high-surface sensors to measure current density and temperature in the active area plane, along with neutron imaging to determine liquid water distributions. Employing a pseudo three-dimensional two-phase flow model that integrates electrochemical and transport phenomena, we gain insight into the intricate relationships among these observables. The model proves particularly valuable in elucidating the operation of the anode and cathode sides, aspects challenging to capture solely through experimental mean. Our findings emphasize the substantial impact of fluid flow directions and current density on the distribution of liquid water. It is noteworthy that despite fluid flow direction, there is a consistent decrease in overall liquid water content with an increase in current density. This results in voltage instability within the cell, attributed to flooding phenomena, especially at low current densities. However, this is not observed in conditions representative of those encountered in on-field systems. We conduct a thorough analysis of this failure scenario to improve the fuel cell system’s control mechanisms.

Wavelength-Resolved Neutron Imaging Technique for Metal Material Analysis

Wavelength-Resolved Neutron Imaging Technique for Metal Material Analysis