Iliosacral Screw Research Articles

CT-Based Evaluation of Volumetric Posterior Pelvic Bone Density with Implications for the Percutaneous Screw Fixation of the Sacroiliac Joint.

Background: Operative treatment of fragility fractures of the pelvis has become a gold standard. Preoperative planning, including the assessment of the pathway for iliosacral screws, is crucial. The anchorage of the screw depends on the bone quality. Some recent studies have concentrated on assessing bone mineral density (BMD) with the use of Hounsfield unit (HU) values obtained from CT scans. The aim of the present study is to determine the best sacral levels of S1-S3 on the pathway of iliosacral screws for sacroiliac joint fixation. Methods: Patients admitted to the Independent Public Healthcare Center in Rypin between 1 of September and 1 of December in 2023, who had CT scans of the pelvis performed on them for different reasons, were included in this study. In total, 103 patients-56 men and 47 women-were enrolled in the study and consecutively separated into two groups of different ages: 18-60 years old (group A) and above 60 years old (group B). The volumetric bone density expressed in HU values was measured with sacral levels of S1, S2 and S3. Apart from the bodies of sacral vertebrae S1-S3, our measurements involved the ala of the ilium in the vicinity of the sacroiliac joint and the wing of the sacrum. All the measurements were performed on the pathway of presumptive iliosacral screws to stabilize the sacroiliac joint. Results: In group A (58 patients) the highest bone density in sacral bodies was found in S1 that gradually decreased to S3, while the opposite tendency was demonstrated in the ala of ilium. The HU values in the wing of the sacrum did not display statistical significance. In group B (45 patients), the highest bone density was also found in the sacral body S1 that decreased toward S3 but in the ala of ilium, the highest bone density was found with level S1 and lowest with level S2. In both groups, the highest bone density referred to the wing of the sacrum. Conclusion: While the perfect construct for posterior pelvic ring fixation remains unclear, our findings may imply that sacroiliac joint screws inserted into the wing of the sacrum of greater bone density could provide much more successful fixation in comparison to those anchored in the body of sacral vertebra of lesser bone density.

Simplifying the Orientation of S1 Iliosacral Screws for Placement in the Dysmorphic Sacrum.

Determining the proper iliosacral screw orientation in a dysmorphic S1 sacral segment using a C-arm is difficult, and pelvic computed tomography (CT) is often necessary for the preoperative planning. On the preoperative pelvic axial CT section, the intended screw trajectory can be delineated intraosseously along the axis of the oblique osseous corridor. An inherently accurate orientation would be determined by 2 factors: (1) the trajectory is in the pelvic transverse plane, and (2) it is oriented relative to the coronal plane at a patient-specific angle, which should be measured preoperatively. Based on the above reasoning, we aimed to simplify and verify the orientation. After establishing the starting point on the sacral lateral view, we tested a method of simplifying the guidewire orientation: placing the guidewire in the pelvic transverse plane and then manipulating it to be angled relative to the coronal plane at the preoperatively measured patient-specific angle. The guidewire orientation should then be reproducibly accurate on the pelvic outlet and inlet views. The feasibility and safety of our method were verified through computer-simulated virtual surgical procedures in 95 dysmorphic sacra and clinical surgical procedures in 12 patients. The primary outcome parameters were the guidewire orientation and screw placement accuracy. Using our method, the S1 guidewire orientation was reproducibly accurate on the pelvic outlet and inlet views in all of the virtual and clinical surgical procedures. Ninety-five virtual S1 screws (1 screw in each left hemipelvis) were placed intraosseously in the pelvic transverse plane. Fourteen unilateral S1 screws were placed intraosseously in the pelvic transverse plane in the 12 patients (2 patients had double screws) without iatrogenic injuries. The guidewire orientation can be simplified by placing the guidewire in the pelvic transverse plane and replicating the preoperatively measured patient-specific angle between the guidewire and the coronal plane. After establishing the starting point on the sacral lateral view, our simplified manipulation yields a reproducibly accurate orientation on the pelvic outlet and inlet views. Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Retrospective Evaluation of Pelvic Fractures in Cats: 144 Cases (2018-2023)

Objectives: This study aims to examine pelvic fractures in cats brought to the XXXX University Animal Health and Research Hospital between 2018 and 2023. Materials and Methods: Using a retrospective design, the study analyzed data from 144 cats. Results: The data revealed that pelvic fractures generally occurred as a result of traumatic events such as motor vehicle accidents and falls from heights. Of the 259 fracture cases studied, it was determined that 24.32% were pubic fractures, 23.54% were sacroiliac separations, 19.69% were ischial fractures, 12.74% were ilial fractures, 10.42% were symphysis pelvis separations, 7.72% were acetabular fractures, and 1.54% were sacral fractures. Patients in the study were treated conservatively or operatively (using methods such as iliosacral screws, acetabular C plates, locked plates, cerclage wires, and dorsal laminectomy). Conclusions: In conclusion, operative treatment plays a significant role in the management of pelvic fractures, and the suitability of surgery should be carefully evaluated. Clinical outcomes indicated that cats undergoing operative treatment achieved more favorable results and higher discharge rates.

Lumbopelvic Stabilization with Two Methods of Triangular Osteosynthesis: A Biomechanical Study.

(1) Background: Pelvic fractures, and particularly instabilities of the dorsal pelvic ring, are becoming increasingly prevalent, particularly in orthogeriatric patients. Spino-pelvic triangular osteosynthesis is an effective approach to achieve sufficient stabilization in vertically unstable fractures. This study compares two types of osteosynthesis: the conventional one and a novel instrumentation where the iliosacral screw is placed through a fenestrated iliac screw. (2) Methods: Sixteen artificial osteoporotic L5+pelvis models with an unstable sacral fracture have been instrumented with either an iliac screw connected with a rod to a L5 pedicle screw and an iliosacral screw (TF) or a fenestrated ilium screw connected with a rod to a L5 pedicle screw and an iliosacral screw passing through the fenestra of the iliac screw (TFS). Biomechanical testing was performed using cyclic loading until failure. (3) Results: Both configurations yielded comparable results with regard to initial stiffness, implant loosening, and cycles to failure. The TFS exhibited markedly higher values for cycles to failure and markedly lower values for loosening. However, due to the characteristics of the artificial bone model, these findings were not significant. (4) Conclusions: The novel triangular fixation systems demonstrated comparable results to the standard triangular osteosynthesis configuration.

Navigation and 3D-imaging in pelvic ring surgery: a systematic review of prospective comparative studies.

Few literature reviews have been published focusing on navigation, robotic or pre-operative planning using 3D-imaging technology (3D-printing, 3D-planning). To our knowledge, no reviews have been performed to assess and compare all these modalities together versus control groups (conventional fluoroscopy) through high Randomized Control Trials (RCTs) and Prospective Control Studies (PCSs). The aim of this study was to assess and compare 3D-imaging technologies from pre-operative planning to per-operative navigation and robotic in the management of pelvic ring fractures through high level studies. A literature search was performed using PubMed, the Cochrane library and Google scholar using keywords up to December 2023. Only prospective comparative studies (RCT and PCS) were included. A total of 341 articles were identified, 39 articles were selected for full-text analysis leaving 7 articles included in this literature systematic review. A trend towards improved precision in screw placement and reduction of radiation exposure without consequences in term of functional outcomes have been identified. No conclusions can be extrapolated regarding operative time and blood loss except for robotic which improve these parameters because robotic arm assistance help surgeons to correctly follow the planning based on 2D-fluoroscopy. Surgery duration and radiation dose are significantly reduced with robotic-arm assistance for the same reasons. With navigation the results have to be nuanced according to the experience of the surgical team. Interest of navigation is emphasized in sacral dysmorphism in comparison with conventional fluoroscopy. This highlights the benefits of navigation for ilio-sacral screw placement in difficult cases and less experimented teams. High level studies which assess and compare 3D-imaging technologies from pre-operative planning to per-operative navigation and robotic in the management of pelvic ring fractures are low. To date and according to the present high level literature, navigation and 3D-technologies in pelvic ring surgery should be recommended for difficult cases. Systematic review of Level II studies.

Pediatric-Specific Lesions in Unstable Pelvic Ring Fractures of Skeletally Immature Children: Impact on Diagnosis and Management Decisions.

Surgical fixation of pediatric pelvic ring injuries is gaining popularity to avoid the poor long-term outcomes of pelvic asymmetry. The surgical techniques and fixation choices depend on the individual injuries affecting the anterior and posterior pelvic ring areas. The immature bony pelvis of young children has anatomic differences including soft bones, elastic ligaments, and the presence of growth centers. Understanding the unique pediatric lesions with unstable pelvic fractures is essential for treatment decisions. Anterior lesions include pubic symphysis disruption through the pubic apophysis, single ramus fractures, pubic rami fractures through the triradiate cartilage, and/or the ischiopubic synchondrosis; ischiopubic ramus infolding injury; or the unstable superior and inferior quadrant lesions. Posterior pelvic lesions include iliac wing infolding and sacroiliac joint dislocation or transiliac (crescent) fracture/dislocations through the iliac apophysis growth plate. Pubic symphysis and sacroiliac disruptions are physeal injuries in children, and they have excellent healing potential. External fixation is an ideal choice for anterior ring fixation including bony and pubic symphysis injuries. Posterior lesions are mostly sacroiliac joint disruptions with iliac apophysis separation that can serve as a landmark for vertical displacement correction. Posterior lesions can be treated by percutaneous iliosacral screw fixation or open reduction techniques.

Frequency and management of rod fractures following minimally invasive bipolar fusionless surgery in neuromuscular scoliosis patients

IntroductionNeuromuscular scoliosis (NMS) is associated with an abnormal muscle tone. Traditional conservative treatments, with the historical practice of early posterior fusion, have proven ineffective. Recently, growth-sparing techniques have gained traction owing to their ability to maximize trunk height. However, these techniques have a substantial risk of complications, particularly rod breakage, with reported incidence rates ranging from 15 % to 42 %. The objective of this study was to conduct a descriptive analysis of NMS patients who experienced rod breakage following the minimally invasive fusionless surgery (MIFS) technique. MethodsThis was a single-center, retrospective study that included all NMS patients who underwent surgery between January 2015 and January 2021 and subsequently presented with rod breakage after MIFS. The MIFS technique is based on proximal fixation with double hook claws made of pedicular and -sus laminar hooks and pelvic fixation with iliosacral screws. ResultsThe mean follow-up was 5.2 ± 2.2 years. The mean dominant etiology of NMS was cerebral palsy (67 %). Of the 217 patients who underwent surgery, 15 (6.9 %) developed rod breakage. Rod breakage occurred 2.7 ± 1.3 years after the initial surgery. Four cases of rod fracture recurrence were reported in ambulatory patients with dystonia or hyperactivity. ConclusionCompared with other fusionless techniques, the minimally invasive bipolar technique appears promising for patients with NMS, with a lower rate of rod breakage. We recommend the use of a four-rod construct for ambulatory patients or for those with dystonia or hyperactivity.

Influence of age on pelvic inlet and outlet radiographic views

Background. Unstable fractures of the posterior pelvic ring represent a pressing concern in trauma surgery. Minimally invasive osteosynthesis techniques have gained widespread acceptance in contemporary practice. Accurate radiographic visualization is a critical component for the precise and successful placement of iliosacral and transsacral screws. Obtaining and accurately interpreting X-ray images can pose challenges in specific clinical situations, particularly those involving age-related skeletal changes. The aim of the study is to assess the influence of the patient’s age on the measures of pelvic radiographic inlet and outlet views angles for performing a sacral fracture fixation using cannulated screws. Methods. A retrospective analysis of CT data was conducted on 106 patients with posterior pelvic ring injuries requiring cannulated screw fixation. Preoperative CT scans were reconstructed into sagittal projections. We performed construction and measurement of the true inlet angle, super-inlet angle, pelvic outlet angle, sacral concavity angle, promontory angle, S1 and S2 outlet view angles. Statistical correlation between sacral tilt angle and the patient’s age was assessed. Results. A two-step cluster analysis divided the patient cohort into two groups with significant differences in pelvic outlet angles and age (N1 = 64, N2 = 42). Statistically significant differences were found between the two clusters in all the studied parameters: median values of true pelvic inlet angles were 27.2° [23.2-32.2] and 18.2° [11.4-26.6] respectively (p0.001); super-inlet angles were 42.5° [39.3-47.8] and 36.2° [28.7-42.8] respectively (p0.001); promontory angles were 128.1° [123.3-133.2] and 122.1° [115.6-129.3] respectively (p = 0.003); pelvic outlet angles were 62.6° [58.4-69.6] and 50.3° [45.9-53.5] respectively (p0.001); S1 outlet angles were 51.8° [48.9-56.5] and 46.8° [43.1-50.2] respectively (p0.001); S2 outlet angles were 40.8° [37.3-44.6] and 35.7° [30.9-38.6] respectively (p0.001); the mean of the sacral concavity angles was 174.8°±10.5 and 152.1°±38.2 respectively (p0.001); and the main age was 41.6±18.7 and 69.2±16.1 years respectively (p0.001). A statistically significant inverse correlation between age and pelvic tilt angle (ρ = 0.534; p0.001) was found. A novel diagnostic method for identifying sacral dysmorphism using angle measurement within the S1 bone corridor is presented. The sacrum was considered dysmorphic if the angle was equal to or less than 5°. Conclusions. As the patient’s age increases by one year, pelvic outlet angle decreases by 26°. If pelvic inlet angles are equal to or less than 14.45°, the difficulties in visualizing S1 and S2 outlet views during surgery are to be expected. The median of angles difference before and after anterior sacral tilt correction using a coccyx pad was 9.4° with interquartile range from 7.8° to 11°. Significant anatomical variations in posterior pelvic ring structure were observed among the study cohort. Preoperative CT sagittal reconstructions allow appropriate planning of intraoperative visualization considering expected intraoperative radiographic inlet and outlet views.

Comparative Study between Percutaneous Ilioilial Fixator versus Percutaneous Iliosacral Screw in Managing Sacral Fractures

Abstract Background The sacrum is the mechanical nucleus of the axial skeleton, located at the base of the lumbar spine and acts as the keystone at the centre of the pelvic ring. Traumatic sacral fractures are an increasingly recognized diagnosis. Sacral fractures remain a relative uncommon entity in the general population. Objective The aim of this work is to compare between percutaneous iliosacral screw and ilioilial fixation in sacral fractures fixation as regard operative time, need of intraoperative fluoroscopy, blood loss & related transfusion, infection, neurovascular complication, hardware failure and screws miss- displacement, clinical and radiological outcomes, revision rate and rate of non-union. Patients and Methods After obtaining the hospitals Research/Ethics Committee approval and written informed consents from the patients. This study was carried on 51 Patients with sacral fractures injuries through the period from August 2019 to November 2021. A prospective randomized controlled clinical trial was conducted to compare the functional and radiological outcome of closed reduction and percutaneous fixation of traumatic sacral fractures using iliosacral screw or ilioilial fixator. Results There is no statistically significant difference in functional outcome, radiological outcome operative time, blood loss, postoperative complication, union rate or follow up. There is statistically significant difference in incision length between the two groups as mean length of incision in iliosacral screw and Ilioilial fixator is 1.2 cm and 4.8 cm respectively. There is statistically significant relation between number of intraoperative fluoroscopic and fixation principles (P value <0.001) with higher risk for radiation exposure in IS screw group. Conclusion Iliosacral screw and ilioilial fixator have comparable functional and radiological outcome and similar biomechanical stability .We suggest the ilioilial fixator as an alternative to IS screw in sacral fracture management. The ilioilial fixator is a useful option in patients who do not qualify for IS screw fixation.

Treatment Outcomes in Vertical Shear Pelvic Fractures: A Comparative Study.

Background Vertical shear (VS) pelvic ring injuries present a unique challenge due to their inherent vertical and rotational instability and the risk of massive bleeding. VS injuries may result from either bony or ligamentous injury. The goal in the treatment of VS fractures of the pelvis is to achieve and maintain an accurate reduction of the displaced hemipelvis. Aim of the study This study aimed to compare the results of the treatment of VS fractures pelvis by using iliosacral (IS) screws versus lumbopelvic fixation (LPF). Methodology This retrospective study was carried out on 40 patients with VS fracture pelvis injuries at El Hadara University Hospital, Alexandria, Egypt, from January 2020 to December 2020. Twenty of them were treated by an IS screw, and the other 20 were treated by LPF. Then, both groups were followed up for six months with regard to union rate, metal failure, and clinical outcomes. Results The EQ-5D showed a significant improvement in LPF more than the IS screw group in the five items of the score. Moreover, the total EQ-5D index showed a significant increase in the LPF group more than the IS screw group (p < 0.05). The incidence of neurological complication was found in four cases in the IS screw group, while no cases were found in the LPF group. The infection was found in six patients in the IS screw group and only three cases in the LPF group. The malunion was found in two cases in the IS screw groupand no cases in the LPF group. The neurological change and the incidence of infection were significantly higher in the IS screw group than in the LPF group (p < 0.05). Conclusion Our results demonstrate reliable maintenance of reduction and acceptable complication rates with a minimally invasive LPF for VS fractured pelvis. The benefits of minimally invasive LPF may be offset by increased elective reoperations for the removal of instrumentation.

Fixation of Sacral Ala Fracture Using a Midfoot Mesh Plate as a Cannulated Screw Washer: A Case Report

Introduction: Sacral fractures are rare but are increasing in incidence among trauma patients. They are associated with a wide variety of complications, most commonly neurologic defects. Case Report: A 59-year old woman initially underwent open reduction internal fixation (ORIF) for a sacral fracture, after which the patient developed an infection, wound complications, and hardware failure. The revision of the iliosacral screws proved challenging in that the standard screw and washer could not achieve sufficient compression of the fracture. Therefore, a modified midfoot mesh plate was cut to size and used as a washer to gain more surface area, achieving fixation. The plate was applied laterally and cut to cover as much surface area as possible without unnecessary bony overhang. A trans-iliac trans-sacral screw was then inserted in the standard fashion, thus allowing the plate to act as a washer. This resulted in an excellent outcome with appropriate fracture healing. Conclusion: We describe the case of an iliosacral screw revision in which a modified midfoot mesh plate was used as a washer. This resulted in appropriate fixation in the revision settings. The principles described to achieve this fixation can be broadly applied in the setting of orthopedic fractures.

Clinical development of ileofemoral thrombosis caused by malposition of the ileosacral screw

Introduction Treatment of unstable injuries of the pelvic bones is one of the unsolved problems in modern traumatology. The instability of the injuries is determined by the nature of the destruction of the posterior semi-ring of the pelvis. The most used technique for osteosynthesis of sacral fractures for unstable pelvic injuries is ileosacral screw fixation.The purpose of the work was to demonstrate a clinical case of an iatrogenic complication: ileofemoral thrombosis caused by compression of the internal iliac vein due to malposition of the ileosacral screw.Materials and methods Medical records of a 34-year-old patient injured in a traffic accident (front seat passenger) were studied, who was referred from a district hospital on the fourth day after the injury diagnosed with a fracture of the transverse process of L2 vertebra on the left, closed fracture of the pubic and ischial bones on the left, fracture of the lateral mass of the sacrum on the right. Alcohol intoxication. Traumatic shock stage 1. Treatment results were monitored throughout the inpatient and outpatient treatment periods. Long-term follow-up was 6 months.Results Timely suspicion of the complication based on physical examination data with CT angiography that assisted to exclude internal bleeding and urgently carry out repeated surgical intervention to correct the implant malposition, reosteosynthesis of S1 body without loss of reduction, to achieve regression of the clinical picture of ileofemoral thrombosis, and also to mobilize the patient in the shortest possible time. During inpatient treatment, regression of the symptoms of the complication was achieved, the patient was fully activated, and was discharged for outpatient follow-ups.Discussion Variability in the anatomy of the sacrum and the characteristics of fractures hinder the navigation while inserting iliosacral screws, which in some cases result in malposition. Compression of the common iliac vein without damaging it causes difficulty in blood outflow and the development of a clinical picture of ileofemoral thrombosis in the early postoperative period.Conclusion This clinical case shows that X-ray images in standard views are not a reliable method for diagnosing sacral injuries and are not sufficient for preoperative planning. The use of standard C-arm did not provide sufficient intraoperative visualization to correctly assess the position of the iliosacral screw, especially in cases with sacral dysmorphia. The 3D volumetric image reconstruction significantly influenced the correct perception of the anatomical structure of the bony structures of the pelvis. Malposition of the screw and its exit to the anterior surface of the sacrum caused disruption of the iliac vein outflow and development of thrombosis in the early postoperative period.

Placement of ilio-sacral screws in fusionless technique for pediatric neuromuscular scoliosis utilizing planning software, in conjunction with intraoperative navigation, results in a safer optimal screw: a CT-based study.

The insertion of ilio-sacral (IS) screws for distal anchoring in the instrumentation of pediatric neuromuscular scoliosis (NS) presents a significant challenge, often leading to elevated rates of complications. Utilizing computed tomography (CT) navigation and preoperative planning technology is proposed as a potential solution to mitigate these challenges. This study aims to assess the precision of IS screw placement through CT-graphic measurements, both with and without preoperative planning, followed by navigated IS screw insertion, in pediatric neuromuscular scoliosis. Thirty-two treated patients were grouped based on surgical procedure: planned (P): 19 patients (n=38 screws) and non-planned (NP): 13 patients (n=26 screws). All screw placements (P and NP) took place under CT navigation. IS screw trajectories of P-group were drawn preoperatively on CT images with the cranial trajectory planning program and fused with the intraoperative CT images. There are several important anatomical structures that should be avoided when placing the IS screw (L5 root, spinal canal, L5S1 facet, SI joint, neurovascular structures anteriorly to the sacrum, S1 root in the S1 foramen and the intestines). Each trajectory was evaluated based on seven radiographical parameters whom we have enlisted partially based on the essentials of a good trajectory described by Miladi et al. (1: Ilium; 2: SI joint; 3: Promontorium; 4: Sacral plate; 5: Anterior sacral cortex; 6: S1 foramen; 7: Spinal canal). An independent sample T test was executed to compare both groups. The trajectories in the P group showed a significantly (P<0.05) higher overall similarity and optimality (12.1±2.1 vs 9.1±2.2 points) compared to the non-planned trajectory. Preoperative planning and navigated placement of IS screws on fusion images with intraoperative CT, results in a better trajectory of the ilio-sacral screws.

Insertion sites of iliosacral screws on the posterior ilium: Implications for posterior pelvic fixation

ObjectivesLateral compression type II pelvic ring injuries can be treated with fixation through open or percutaneous approaches depending on the injury pattern and available osseous fixation pathways. The start site of iliosacral screws to stabilize these injuries should be on the unstable posterior iliac fragment; however, our understanding of start sites for iliosacral screws has not been developed. The purpose of this study is to provide an analysis of iliosacral screw start sites on the posterior ilium to help guide treatment of pelvic ring injuries. MethodsOne-hundred and seventeen consecutive patients at an academic level I trauma center with pelvic ring injuries who underwent surgical treatment with iliosacral screws were included in the final analysis. The start sites of iliosacral screws with confirmed intraosseous placement on a postoperative computed tomography were mapped on the posterior ilium and analyzed according to the sacral segment and type of iliosacral screw. ResultsOne-hundred and seventeen patients were included in the final analysis. Of the total of 272 iliosacral screw insertion sites analyzed, 145 (53%) were sacroiliac-style screws and 127 (47%) were transsacral screws. The insertion sites for sacroiliac-style screws and transsacral screws at different sacral segment levels can vary but have predictable regions on the posterior ilium relative to reliable osseous landmarks. ConclusionsIliosacral screws start sites on the posterior ilium have reliable regions that can be used to plan posterior fixation of pelvic ring injuries.

Anatomical evaluation of sacrum in dry bones

Objectives: The sacrum is a critical bone in various clinical procedures, including caudal epidural blocks, iliosacral screw placements, fetal growth assessment, and sacral nerve stimulation. This study aims to investigate the morphometry and variational morphology of the anatomical formations in the pelvis and dorsal surface of the sacrum. Methods: Morphometric and morphological characteristics of 30 sacral bones of unknown age and sex were examined. Measurements were made using a digital caliper. Results: The mean height of the sacrum was 106.67±10.16 mm, while their mean width was 103.60±6.78 mm. The morphometric analysis revealed that the mean length of the sacral hiatus was 18.51±7.44 mm, and the distance between the sacral cornua was 11.80±2.46 mm. The sacral hiatus was most commonly observed in an inverted ‘U’ shape, while the least common form was bifid. The sacral canal typically displayed a V-shaped morphology. It was determined that the apex of the sacral hiatus most frequently started at the S4 level (80%) compared to the sacral vertebra, and the base of the sacral hiatus mostly ended at the S5 level (93.4%). Conclusion: Morphometry of the sacrum is essential in guiding clinicians, especially in interventions such as anesthesia and orthopedics. Discrepancies in parameter studies conducted in some countries suggest the significance of ethnic factors. Therefore, it is essential for the number of studies to increase and for physicians to follow the parameters of their society regarding the effectiveness of the treatments.

Critical distance of the sacroiliac joint for open reduction using screw fixation for traumatic sacroiliac joint diastasis: a retrospective study

BackgroundOsteosynthesis for sacroiliac joint (SIJ) diastasis using an iliosacral screw (ISS) and a trans-iliac-trans-sacral screw (TITSS) can be performed using a closed or an open method. However, no clear indication for open reduction has been established.MethodsData on patients with unilateral traumatic SIJ diastasis who underwent ISS and TITSS fixation were retrospectively collected and separated into groups according to the reduction method: closed reduction group (C group) and open reduction group (O group). Demographic data and perioperative image assessments were compared between the groups. The critical distance of the SIJ was identified to elucidate the indication for open reduction of the diastatic SIJ.ResultsFifty-six patients met the inclusion criteria over a 3-year period. There was no significant difference in the reduction quality of pelvic ring injuries between the groups, according to Matta’s and Lefaivre’s criteria. The improvement in the SIJ distance was significantly greater in the O group than in the C group in the axial plane on multiplanar computed tomography (p = 0.021). This model predicted that a difference of > 3.71 mm between the injured and healthy SIJ was a recommended indication for open reduction, with an area under the curve of 0.791 (95% confidence interval 0.627–0.955, p = 0.004).ConclusionsOpen reduction for SIJ diastasis might achieve better reduction quality than does closed reduction in the axial plane in selected cases. When the difference between the injured and healthy SIJ was wider than 3.71 mm, open reduction was recommended for satisfactory radiological outcomes.

The “Metaizeau trick” to facilitate medullary pubic ramus screw insertion: A technical note

Minimally invasive procedures have recently seen an increase in the treatment of pelvic ring disruptions and select acetabular fractures. Similar to ilio-sacral screws, the superior pubic ramus screw is becoming a preferred method for treating unstable pelvic ring fractures. While the osteology of the superior pubic ramus is well understood and has inherent variability, standard screw insertion techniques work effectively in most cases. If the anatomy prevents the standard approach, there are alternative methods that can be employed for successful screw placement, or there might be a need for an open reduction and internal fixation with plates. Such techniques can be material-intensive and time-consuming. In this paper, we introduce a straightforward method that utilizes the Metaizeau nail as a guide wire to facilitate screw insertion in most instances, termed the “Metaizeau trick”. Metaizeau nails, commonly found in trauma centers, are designed to locate a pathway effortlessly using this method. Level of evidenceIV.

Navigation versus fluoroscopy in minimalinvasive iliosacral screw placement

IntroductionWhen needed operative treatment of sacral fractures is mostly performed with percutaneous iliosacral screw fixation. The advantage of navigation in insertion of pedicle screws already could be shown by former investigations. The aim of this investigation was now to analyze which influence iliosacral screw placement guided by navigation has on duration of surgery, radiation exposure and accuracy of screw placement compared to the technique guided by fluoroscopy.Methods68 Consecutive patients with sacral fractures who have been treated by iliosacral screws were inclouded. Overall, 85 screws have been implanted in these patients. Beside of demographic data the duration of surgery, duration of radiation, dose of radiation and accuracy of screw placement were analyzed.ResultsWhen iliosacral screw placement was guided by navigation instead of fluoroscopy the dose of radiation per inserted screw (155.0 cGy*cm2 vs. 469.4 cGy*cm2p < 0.0001) as well as the duration of radiation use (84.8 s vs. 147.5 s p < 0.0001) were significantly lower. The use of navigation lead to a significant reduction of duration of surgery (39.0 min vs. 60.1 min p < 0.01). The placement of the screws showed a significantly higher accuracy when performed by navigation (0 misplaced screws vs 6 misplaced screws—p < 0.0001).ConclusionBased on these results minimal invasive iliosacral screw placement guided by navigation seems to be a safe procedure, which leads to a reduced exposure to radiation for the patient and the surgeon, a reduced duration of surgery as well as a higher accuracy of screw placement.

Percutaneous Ilioilial Fixator Versus Percutaneous Iliosacral Screw in Managing Unstable Sacral Fractures: A Prospective Randomised Controlled Study.

Unstable sacral fractures with pelvic fractures are challenging to both surgeons and patients, particularly in the immediate post-injury phase and later when definitive fixation is undertaken. Percutaneous iliosacral screw fixation is widely regarded as the gold standard treatment for unstable sacral fractures without spinopelvic dissociation. Closed reduction and percutaneous fixation using iliosacral screws for sacral fractures provide early stabilisation without the need for extensive surgical exposure, thereby mitigating major complications associated with open surgical procedures. A new technique for stabilising unstable sacral fractures is the minimally invasive ilioilial fixator, also called a transiliac internal fixator (TIIF), which has gained more attention for its ability to address challenges associated with sacroiliac screw fixation. The objective of this study is to compare the functional, radiological, and surgical outcomes between the percutaneous iliosacral screw and the ilioilial fixator. A total of 51 patients with sacral fracture injuries sustained between August 2019 and November 2021 were included in this study, with 25 patients in Group A and 26 patients in Group B. Patient randomization was done using computer-generated randomization facilitated by Random Allocation Software (Mahmood Saghaei, Isfahan, Iran). All patients underwent the chosen intervention within 10 days of the trauma. Patients had follow-up at two weeks, six weeks, and 12 months post-treatment. The results of fixation were evaluated radiologically based on the Matta and Tornetta grading system and clinically using the Majeed pelvic scoring system. Complications were detected in both groups during follow-up visits. The study found no statistically significant differences between the two patient groups in terms of final clinical assessment (p=0.79), radiological assessment (p=0.78), or the need for another operation (p=1.0). Moreover, there were no statistically significant differences between the groups with respect to complication rates (p=0.63) or the time of union (p=0.14). No differences were noted in terms of intraoperative blood loss (p=0.93) or operative time (p=0.34) but for longer incision length in the ilioilial fixator group (p<0.001) and an increased risk of intraoperative radiation exposure in the iliosacral screw group (p<00.1). Although the iliosacral screw is considered a gold standard for unstable sacral fracture, a TIIF is a good alternative with a very satisfactory outcome. Although the iliosacral screw still remains the gold standard for the management of sacral fractures, the ilioilial fixator emerges as a good alternative with comparable functional and radiological outcomes.

Long-Term Follow-Up after Iliosacral Screw Fixation of Unstable Pelvic Ring Fractures.

(1) Background: High-energy injuries of the pelvic ring are rare. The wide application of iliosacral screw fixation of the posterior pelvic ring is relatively new. The aim of the present study was to evaluate the long-term quality of life. (2) Methods: All patients treated with an iliosacral screw for a posterior pelvic ring stabilization after high-energy trauma at a level 1 trauma center between 2005 and 2015 were included. Pelvic ring injuries were classified according to the Tile classification adapted by AO/ASIF. The clinical evaluation included the patient-oriented questionnaires surveys of the Majeed Score, Iowa Pelvic Score (IPS), Work Ability Index (WAI), SF-36, EQ5D-5L. (3) Results: A total of 84 patients were included with a median follow-up of 130.1 months (IQR 95.0-162.0 months). The median ISS was 22.5 (IQR 16.0-29.0), mean Majeed Score 83.32 (SD ± 19.26), IPS 77.88 (SD ± 13.96), WAI 32.71 (SD ± 11.31), SF-36 PF 71.25 (SD ± 29.61) and EQ5D-5L 0.83 (SD ± 0.21). There was a notably difference between uni- and bilateral pelvic fractures (p = 0.033) as well as a correlation with the ISS (p = 0.043) with inferior functional outcome measured by IPS. (4) Conclusions: Long-term follow-up of iliosacral screw fixation of unstable pelvic ring fractures showed a good quality of life and functional outcome with equal EQ5D-5L results and inferior SF-36 physical functioning compared to the German population.