Hydroxyapatite Coatings Research Articles

Influence of Detonation Spraying Parameters on the Microstructure and Mechanical Properties of Hydroxyapatite Coatings.

The process of osteointegration depends significantly on the surface roughness, structure, chemical composition, and mechanical characteristics of the coating. In this regard, an important direction in the development of medical materials is the development of new techniques of surface modification and the creation of bioactive ceramic coatings. Calcium-phosphate materials based on hydroxyapatite have been proposed as bioactive ceramic coatings on titanium implants for the effective acceleration of bone tissue healing. To obtain bioactive ceramic coatings, pulse power sources are best suited, namely detonation spraying, in which the energy of the explosion of gas mixtures is used as a source of pulse action. The pulse mode of operation in the detonation spraying method is preferable for the formation of bioactive ceramic coatings. It provides a high velocity of hydroxyapatite particles, which promotes their effective fixation on the titanium substrate, while minimizing the heating of the material. This approach preserves the substrate structure and improves the coating adhesion. Four different types of coatings with varying O2/C2H2 molar ratios, ranging from 2.6 to 3.7, were obtained using detonation spraying. Powders and obtained coatings of hydroxyapatite were studied by Raman spectroscopy and XRD structural analysis. The results of XRD phase analysis showed the partial conversion of the hydroxyapatite phase to the α-tricalcium phosphate (α-TCP) phase during the detonation spraying process. The results obtained by Raman spectroscopy indicate that hydroxyapatite is the main phase in coatings. All hydroxyapatite-based coatings exhibited hydrophobic properties, which was confirmed by contact-angle values above 90° in wettability tests, characteristic of hydrophobic surfaces. The adhesive strength of the coatings was measured by the scratch test method. Tribological tests were conducted using the ball-on-disk method under both dry conditions and in Ringer's solution. This approach enabled the evaluation of wear resistance and friction coefficient of the coatings in different environments, simulating both lubrication-free conditions and those resembling physiological environments.

3D-printed porous calcium silicate scaffolds with hydroxyapatite/graphene oxide hybrid coating for guided bone regeneration

Calcium silicate (CS) is a suitable bone repair material due to its bioactivity and biocompatibility. However, its rapid degradation rate and poor cell response affect the bone regeneration process. Surface modification of implants represents a potent strategy for enhancing the performance of biomaterials. Here, we present a novel method combining hydrothermal treatment and chemical grafting to tailor the surface morphology and composition of 3D-printed calcium silicate porous scaffolds. The resulting scaffold surface features hydroxyapatite (HA) nanosheets and graphene oxide (GO) sheet structures. Surface modification significantly reduced the degradation rate of CS scaffolds and decreased the Si ion concentration after PBS immersion, which was more conducive to cell survival. Our findings reveal that the CS/HA/GO scaffold exhibits superior biocompatibility and significantly enhances cell adhesion, proliferation, and osteogenic differentiation. In vivo studies demonstrate that the CS/HA/GO scaffold markedly promotes the regeneration of defective bone tissue. This work highlights the potential of HA and GO coatings on interconnected porous scaffolds to induce bone tissue regeneration, offering a promising strategy for orthopedic applications.

Characterization of ZnO-Doped Hydroxyapatite Coatings on PEEK Made by Hybrid Plasma Spraying Process for Biomedical Applications

Characterization of ZnO-Doped Hydroxyapatite Coatings on PEEK Made by Hybrid Plasma Spraying Process for Biomedical Applications

Effect of non-contact induction heating on HA coatings and bone cement, an ex vivo study

Background Prosthetic joint infection is a serious complication that can arise after total joint replacement surgery. When bacteria colonise an orthopaedic implant, they form biofilms that protect them from their environment, making them difficult to remove. Treatment is further complicated by a global rise of antimicrobial resistance. These protective mechanisms make treatment of prosthetic joint infection increasingly complex. Non-contact induction heating is an upcoming technology that uses heat to eradicate bacteria that are present on the surface of metallic implants. This study aims to provide insight into the feasibility of using non-contact induction heating on metallic implants that are in direct contact with other biomaterials, such as coatings composed of hydroxyapatite and bone cement composed of poly (methyl methacrylate) (PMMA). Methods Characterisation of hydroxyapatite coatings and adhesion strength tests were conducted according to standards set by the International Organisation for Standardisation (ISO 13779-2). The fixation strength of acrylic bone cement was tested according to an adapted method from ISO. Results It was found that non-contact induction heating did not significantly affect the adhesion strength of hydroxyapatite coatings. In contrast to hydroxyapatite coatings, acrylic bone cement softened temporarily as the temperature exceeded the glass transition temperature (83.38 ± 10.88°C). However, the induction heating temperature had no significant effect on the fixation strength after the cement was allowed to cool down. Conclusion This study shows the feasibility of using non-contact induction heating up to 80°C when bone cement or ceramic coatings are present in contact with infected metallic implants.

Advancements in biomedical coatings: A comprehensive review of DC magnetron sputtering on Ti–6Al–4V alloy

This study investigates the application of DC magnetron sputtering (MS) technology for producing TiN and ion-substituted Ca-P coatings on dental implant materials, demonstrating ultimate tensile strength (UTS) of 887 MPa, a modulus of elasticity of 11.3 × 106 MPa. The influence of various physical vapor deposition (PVD-MS) parameters—such as substrate temperature, post-heat treatment, deposition duration, discharge power, and bias voltage—on the characteristics of these coatings is examined. The research evaluates the advantages and limitations of PVD-MS in fabricating TiN and Ca-P coatings, with an emphasis on their impact on surface topography and chemical composition, which are critical factors influencing cellular behavior. The study reveals that while ion-substituted HA coatings can enhance cell adhesion, they may also exhibit cytotoxic effects, potentially limiting cell growth. It compares osteogenic cell proliferation rates between low-crystalline HA coatings and highly crystalline variants on Ti-based substrates, highlighting significant performance disparities. Additionally, PVD-MS demonstrates robust adhesion capabilities and facilitates the incorporation of therapeutic ions, effectively replicating bioapatite properties. The addition of coating on the substrate promotes additional strengthening mechanisms of the layers, leading to improved wear resistance compared to an alloyed substrate. Estimated values for hardness range between 7.2 and 8.4 GPa, and for Young's modulus, they range from 126 to 162 GPa. The study highlights the potential of PVD-MS in creating nanostructured Ca-P coatings on biodegradable metals, alloys, and polymeric biomaterials. This technology improves corrosion resistance, biocompatibility, chemical stability, wear resistance, and overall performance in various biomedical applications.

On the Role of Substrate in Hydroxyapatite Coating Formation by Cold Spray

The deposition of agglomerated hydroxyapatite (HAp) powders by low-pressure cold spray has been a topic of interest in recent years. Key parameters influencing the deposition of HAp powders include particle morphology and impact kinetic energy. This work examines the deposition of HAp powders on various metal surfaces to assess the impact of substrate properties on the formation of HAp deposits via cold spray. The substrates studied here encompass metals with varying hardness and thermal conductivities, including Al6061, Inconel alloy 625, AISI 316 stainless steel, H13 tool steel, Ti6Al4V, and AZ31 alloy. Single-track experiments offer insights into the initial interactions between HAp particles and different substrate surfaces. In this study, the results indicate that the ductility of the substrate may enhance HAp particle deposition only at the first deposition stages where substrate/particle interaction is the most critical factor for deposition. Features on the substrate associated with the first deposition sprayed layer include localized substrate deformation and the formation of clusters of HAp agglomerates, which aid in HAp deposition. Furthermore, after multiple spraying passes on the various metallic surfaces, deposition efficiency was significantly reduced when the build-up process of HAp coatings shifted from ceramic/metal to ceramic/ceramic interactions. Overall, this study achieved agglomerated HAp deposits with high deposition efficiencies (30–60%) through single-track experiments and resulted in the preparation of HAp coatings on various substrates with thickness values ranging from 24 to 53 µm. These coatings exhibited bioactive behavior in simulated body fluid.

Fabrication, characterization, and in vitro studies of Selenium-substituted hydroxyapatite coatings

Abstract The increasing demand for hydroxyapatite (HA) coatings with enhanced functionality have led to novel materials with compositions that are more closely resembling those of natural bone apatites. In the present study, selenium-substituted (Se–HA) powders with various Se quantities were prepared by chemical precipitation. By applying suspension plasma spray (SPS), the surface of Ti substrates was coated with corresponding Se-HA coatings. The microstructural and physicochemical properties of the powders and the coatings were studied. Analysis by x-ray diffraction indicates that SeO3 2− replaced the PO4 3− groups, affecting the crystal structure and crystallinity of HA. As the extent of Se substitution increases, the lattice volume expands and the crystallinity decreases. The synthesized Se-HA powders were confirmed to be calcium-deficient apatite through energy-dispersive x-ray spectroscopy. However, the high temperature of SPS accelerated volatilization of P, increasing the Ca/(P + Se) ratio of the coatings, whereas the chemical valence state of Se remained unchanged. The Se–HA coating exhibited a high bonding strength of >33 MPa, fully meeting the requirement of 15 MPa as coating implant materials. Dissolution behavior tests indicate that the Se–HA coatings had high solubility in comparison to the HA coating. As the substitution degree of Se increased, the dissolution rate also increased, which greatly enhanced the capacity to generate a bone-like apatite layer. In vitro cell experiments indicate that the Se–HA coatings exhibited excellent biocompatibility, and facilitated adhesion and proliferation of osteoblast MC3T3-E1, even in the presence of fluorine. Furthermore, antibacterial properties of Se–HA coatings were also indicated by inhibition of Staphylococcus aureus, which is the main cause of most infections after orthopedic surgeries. Thus, the Se–HA coatings have potential as implant coating materials for orthopedic applications.

Improving bond strength and deposition efficiency of ceramic coatings via low pressure cold spraying: A study on hydroxyapatite coatings with Cu-Zn blends

This study presents Low Pressure Cold Spraying (LPCS) method for ceramic coatings, aimed at enhancing efficiency and elucidating bonding mechanisms. It focuses on the deposition of ceramic coatings using LPCS, with hydroxyapatite (HA) on 316L stainless steel (SS) as an illustrative example. Despite the advantages of LPCS, retaining HA particles has proven challenging, resulting in thin coatings (11.09 ± 2.56 μm) with low bonding strength (1.80 ± 0.19 MPa). To address this issue, a composite coating strategy was developed by blending 20 wt% Cu and Zn powder with 80 wt% HA. This approach significantly improved coating properties, achieving enhanced bonding strength (33.70 ± 1.13 MPa), deposition efficiency (27 %), and hardness (136.30 ± 2.45 HV) compared to pure Cu-Zn coatings. Numerical simulations were conducted to interpret these experimental results, indicating that blending metal with HA improves deposition efficiency, bonding strength, and hardness. In HA coatings, particles fragment into submicron grains and embed into the substrate through mechanical interlocking (MI), with shockwave-induced bonding strengthening subsequent layers. For Cu-Zn coatings, bonding occurs through MI and adiabatic shear instability (ASI). In HA-Cu-Zn coatings, high-velocity HA particles and Zn particles enhance bonding further through in-situ tamping.

Ti3C2Tx MXene-functionalized Hydroxyapatite/Halloysite nanotube filled poly– (lactic acid) coatings on magnesium: In vitro and antibacterial applications

Magnesium (Mg) stands out in temporary biomaterial applications due to its biocompatibility, biodegradability, and low Young's modulus. However, controlling its corrosion through next-generation polymer-based functional coatings is crucial due to the rapid degradation behavior of Mg. In this study, the function of 2D lamellar Ti3C2Tx (MXene) in Hydroxyapatite (HA) and Halloysite nanotube (HNT) hybrid coatings in biodegradable poly– (lactic acid) (PLA) was investigated. The morphological and structural characterizations of the coatings on Mg were revealed through HRTEM, XPS, SEM-EDX, XRD, FTIR, and contact angle analyses/tests. Electrochemical in vitro corrosion tests (OCP, PDS, and EIS-Nyquist) were conducted for evaluate corrosion resistance under simulated body fluid (SBF) conditions. The bioactivity of the coatings in SBF have been revealed in accordance with the ISO 23,317 standard. Finally, antibacterial disk diffusion tests were conducted to investigate the functional effect of MXene in coatings. It has been determined that the presence of MXene in the coating increased not only surface wettability (131°, 85°, 77°, and 74° for uncoated, pH, PHH, and PHH/MXene coatings, respectively) but also increased corrosion resistance (1857.850, 42.357, 1.593, and 0.085 × 10–6, A/cm2 for uncoated, pH, PHH, and PHH/MXene coatings, respectively). It has been proven that the in vitro bioactivity of PLA-HA coatings is further enhanced by adding HNT and MXene, along with SEM morphologies after SBF. Finally, 2D lamellar MXene-filled coating exhibits antibacterial behavior against both E. coli and S. aureus bacteria.

Hydroxyapatite nano-pillars on TI-6Al-4V: Enhancements in cell spreading and proliferation during cell/surface integration.

Despite the attractive combinations of cell/surface interactions, biocompatibility, and good mechanical properties of Ti-6Al-4V, there is still a need to enhance the early stages of cell/surface integration that are associated with the implantation of biomedical devices into the human body. This paper presents a novel, easy and reproducible method of nanoscale and nanostructured hydroxyapatite (HA) coatings on Ti-6Al-4V. The resulting nanoscale coatings/nanostructures are characterized using a combination of Raman spectroscopy, scanning electron microscopy equipped with energy dispersive x-ray spectroscopy. The nanostructured/nanoscale coatings are shown to enhance the early stages of cell spreading and integration of bone cells (hFOB cells) on Ti-6Al-4V surfaces. The improvements include the acceleration of extra-cellular matrix, cell spreading and proliferation by nanoscale HA structures on the coated surfaces. The implications of the results are discussed for the development of HA nanostructures for the improved osseointegration of Ti-6Al-4V in orthopedic and dental applications.

Optimizing biomimetic hydroxyapatite coating on Ti-6Al-6Mo alloy: influence of immersion time

This study investigates the formation and characteristics of hydroxyapatite (HAp) coating on Ti-6Al-6Mo alloy through immersion in a supersaturated calcification solution (SCS) for 3, 7, and 14 days. X-ray diffraction (XRD) and secondary electron microscopy (SEM) with electron dispersive spectroscopy (EDS) were used to identify the phases and characterize the morphology and composition of the HAp layer. Atomic force microscopy (AFM) and contact angle tests were used to evaluate the surface properties, while potentiodynamic corrosion testing in Hanks’ solution was used to assess corrosion behavior. It is confirmed that the sample immersed for 14 days formed an HAp layer on the Ti-6Al-6Mo substrate with a Ca/P ratio of 2.5, approaching the ideal value of 1.67. This HAp film exhibits a smooth and homogeneous crystal structure, with a surface roughness of 31.47 nm and an appreciable corrosion rate of 0.0005 mm y−1. This study signifies the impact of immersion time on the microstructural properties and biocompatibility of biomimetic HAp coatings applied to Ti-6Al-6Mo alloy, contributing to the progress of HAp coatings in biomedical engineering.

Ultrasonic vibration-assisted femtosecond laser submerged ablation process for the preparation of titanium-based crack-free hydroxyapatite

Titanium alloy-based hydroxyapatite (HAp) coating materials are beneficial for reducing stress shielding and improving the biocompatibility of implants. However, the significant disparity in thermal conductivity between titanium alloy and hydroxyapatite results in the material being highly susceptible to cracking during preparation, which diminishes the mechanical properties of the material and predisposes the implant to aseptic loosening. To obtain coatings of HAp that are free of cracks, this study proposes a process method of ultrasonic-assisted femtosecond laser under-liquid ablation of a Ca/P solution to synthesize HAp by a one-step process and apply coatings on the surface of TC4 titanium alloy. The relationship between the laser process parameters and the resulting surface morphology, coating spatial distribution, elemental composition, chemical state of the elements, phase, coating thickness, coating bonding, friction coefficient, corrosion resistance and the number of cells was investigated through a series of analytical techniques, including high-speed photographic observation, scanning electron microscopy (SEM), X-ray Photoelectron Spectroscopy (XPS), energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), scratch testing, Tafel plot and cell adhesion assays. The findings demonstrate that titanium-based HAp coatings with a thickness of 42.5 μm, a bonding force of 55 N, a polarization resistance of 10 Ω.cm2, the absence of cracks defects, and notable bioactivity can be produced with ultrasonic-assisted submerged laser ablation in a highly concentrated Ca/P solution. The proposed method represents a novel approach to the preparation of multifunctionalized implants.

Preparation and Biological Evaluation of Porous Tantalum Scaffolds Coated with Hydroxyapatite.

Orthopedic implants, such as porous scaffolds, are an effective way to repair bone defects. However, the lack of osseointegration and osteoinduction limits the achievement of an ideal therapeutic effect. This study aimed to prepare hydroxyapatite (HA) coatings for the surface of porous tantalum (Ta) scaffolds and to assess the effectively improved biological activities of the coated scaffolds. The porous Ta scaffolds were prepared by chemical vapor deposition, and then the porous Ta scaffolds were coated with HA via electrochemical deposition. The elements and phase compositions of the coatings were analyzed by energy-dispersive X-ray spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The results showed that the coating covered the whole surfaces of porous Ta scaffolds with a uniform and compact distribution and did not exert any obvious effect on the porous structure. The biological activity of porous Ta scaffolds after surface modification increased and the water contact angle decreased, indicating that hydrophilicity was significantly improved. Cell live/dead staining, cytoskeletal fluorescence staining, and alkaline phosphatase immunofluorescence staining showed that the coating exhibited no cytotoxicity and notably improved cell proliferation, spreading, and osteogenic differentiation. In addition, in vivo experiments in animals have demonstrated that HA-coated porous Ta scaffolds contribute to bone formation. In conclusion, the HA coating notably improves the biological activities of the porous Ta scaffolds, achieving the goal of the present study. The HA coating presents great potential for the modification of porous Ta implants to improve their osteogenesis and osseointegration.

Preparation and characterisation of gradient HA/TiN/Ti coatings for biomedical applications

A gradient transition HA/TiN/Ti composite coating was deposited on the surface of medical Ti6Al4V alloy using the reactive magnetron sputtering technique. The influence of deposition parameters on the microstructure, mechanical properties, corrosion resistance, and in vitro mineralisation of the coating were systematically investigated. The results demonstrated that deposition parameters such as sputtering power, bias voltage, and sputtering pressure had a significant impact on the microstructure and morphology of HA/TiN/Ti composite coatings. The gradient TiN/Ti transition layer remarkably enhanced the adhesion strength, increasing the critical load from 7.5 N (HA monolayer) to over 40 N (HA/TiN/Ti multilayer). Moreover, compared to single TiN/Ti and HA coatings, the HA/TiN/Ti composite coatings exhibited better corrosion resistance and metal ion shielding ability while also demonstrating excellent capability for inducing bone-like apatite formation, thereby greatly ensuring the exceptional stability of the surface bioactive coatings.

Engineering bioactive MWCNT-reinforced hydroxyapatite coatings on Ti29Nb5Zr alloy by plasma electrolytic oxidation method: A comprehensive approach to dental implant surface optimization

Titanium-niobium-zirconium (TiNbZr) alloys represent a promising class of newly developed titanium-based biomaterials, engineered to exhibit superior properties for biomedical applications. This study investigates the influence of hydroxylated multi-walled carbon nanotubes (MWCNTs) on the surface properties of hydroxyapatite coatings prepared by the plasma electrolytic oxidation (PEO) method for implant applications. The optimal concentration of MWCNTs in the PEO coating was determined based on the superior surface, electrochemical, and biological properties obtained. The incorporation of MWCNTs led to an enhancement in surface roughness from Ra 0.06 ± 0.02 to Ra 0.618 ± 0.03 µm, improved wettability with a decrease in contact angle from 63.03° ± 1.1–28.29° ± 0.07, and a reduction in elastic modulus from 77.20 ± 2.26 GPa to 54.50 ± 2.22 GPa. Furthermore, electrochemical corrosion resistance analysis revealed an increase in inner passivation resistance up to 2.24 × 10 ×7 Ω.cm2 with the addition of MWCNTs. Antibacterial activity analysis demonstrated that the optimal concentration of MWCNTs resulted in a 3.1-fold and 2.7-fold reduction in E. coli and S. aureus bacteria, respectively, compared to uncoated samples. Cell viability against MC3T3-E1 cells showed a 25 % higher viability with MWCNTs than uncoated substrates.

Preparation and characterization of mesoporous HA coating with paclitaxel loaded lignin nanospheres on titanium surface

BackgroundPrimary malignant bone tumor is a disease that can lead to death. The usually applied clinical treatment strategy is surgical resection of the primary tumor. However, tumor cells are difficult to clean up, easy to make the tumor recurrence, and the bone defect caused by surgical resection also hindered the postoperative recovery. Materials and methodsHerein, in this work, mesoporous hydroxyapatite (HA) coating with petal-structure was prepared on titanium (Ti) implant surfaces by micro-arc oxidation (MAO) to accelerate the bone growth, and then paclitaxel (PTX) loaded lignin nanospheres were deposited into the HA coatings to get a sustained release for killing residual tumor cells. ResultsThe results showed that many gaps and holes of micro-scale were formed in the petal-structured HA coatings, they worked as traps for the PTX loaded nanospheres to enhance the deposited amount and immobilization stability, playing good role of drug loading platform. The encapsulation of PTX by lignin ensured a lower release rate and a higher sustaining release time when compared with the PTX without encapsulation. In addition, the HA coating with PTX loaded lignin nanospheres showed higher killing effect to tumor cells than to osteoblast. ConclusionThe mesoporous HA coating with paclitaxel loaded lignin nanospheres endowed the titanium surface with good biological property and tumor cell-killing effect, so the obtained Ti-based material had a highly hopeful application as the localized implant for therapy of primary malignant bone tumor.

Enhancing middle ear implants: Study of biocompatible materials with hydroxyapatite coating

In this manuscript, the application of hydroxyapatite coatings to total ossicular reconstruction prostheses (TORPs) using finite element modeling simulations was investigated to enhance the biocompatibility and mechanical performance of these prosthetic devices for middle ear implants. We focused on evaluating biocompatible materials, particularly polyetheretherketone (PEEK) and titanium, by analyzing their mechanical behavior under simulated conditions. The results revealed that PEEK demonstrates mechanical performance almost on par with titanium, exhibiting excellent stability and resilience within the middle ear environment. PEEK offers several key advantages over titanium, including easier fabrication, greater availability, and a simplified application process for hydroxyapatite coatings. These benefits suggest that PEEK could be a highly effective alternative to titanium for use in middle ear prostheses. The findings of this study highlight the potential of PEEK to improve the design and functionality of middle ear implants, providing a promising direction for future research and development in this field. By leveraging the advantages of PEEK, we can advance the effectiveness and accessibility of middle ear prosthetic devices, ultimately benefiting patients requiring such interventions.

Effect of pH on hydroxyapatite coatings obtained by spray pyrolysis and their use as matrices for antibiotic adsorption by spin coating and release properties.

Calcium phosphate materials, particularly hydroxyapatite (HA), are extensively used in biomedical applications because of their prominence as primary inorganic constituents of human hard tissues. This study investigates the synthesis of HA coatings via spray pyrolysis using various precursors, including HA derived from bovine bone. The effects of pH on the formation and properties of HA coatings were systematically examined. Samples exposed to acidic conditions or left without pH adjustment led to the formation of HA, contrasting with the outcomes observed through dissolution methods. Different characterization techniques, such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD), were employed to evaluate the quality and crystallinity of the coatings. Among the samples, those exhibiting superior crystallinity and nanostructured features, including bovine HA, were selected for further surface functionalization with the antibiotic enrofloxacin using spin coating. As expected, the antibiotic loading on each material's surface depended on the amount of HA deposited on the substrate. However, the desorption results indicated that, in all cases, desorption persisted beyond 38 h, implying that HA-loaded matrices could be effective systems for controlled and prolonged drug release, which could be useful in dental or orthopedic implants for inhibiting the growth of bacterial biofilms.

A REVIEW ON THE MECHANICAL AND TRIBOLOGICAL PROPERTIES OF THERMALLY SPRAYED HYDROXYAPATITE COATINGS FOR BIOMEDICAL IMPLANT MATERIALS

In recent years, many different biomedical implants have been created for prolonged usage within the human body. The number of these implants has been steadily expanding. It is a common practice to use metallic bioimplants as substitutes when attempting to replace human body components in an anatomically acceptable manner. But the metallic bioimplant was mostly made biocompatible by putting a biocompatible coating on its surface and then using the right surface modification techniques. This was the primary method by which the biocompatibility of the bioimplant was achieved. Thermal spraying is a method that is frequently employed in surface modification treatments to modify metallic bioimplants. These methods can be found in the medical field. This is due to the adaptability of the thermal spraying method. Because of their capacity to respond and adapt to physiochemical circumstances, coatings that are based on hydroxyapatite (HAp) are the most popular type to be used in thermal spraying. This is due to the fact that HAp is a naturally occurring mineral. On the other hand, the majority of the HAp coatings are unsuccessful as a result of the coating’s weak mechanical qualities and insufficient adhesive strength. Supplying the coating in question with reinforcement in the form of hard particles and doing so in the appropriate proportions makes it feasible to alter the qualities of HAp-based coatings to fulfill a variety of requirements. This can be accomplished by providing the coating with reinforcement. The purpose of this inquiry was to deconstruct and analyze a variety of thermally sprayed (TS) coatings. These coatings were used to adhere HAp-based coatings on bioimplants. In addition, a detailed discussion is offered on how the reinforcements have an effect on the mechanical and biocompatible qualities of the coatings. In addition, we have discussed the difficulties associated with TS HAp coatings and their potential uses in the manufacturing of 3D biomedical implants through the utilization of cold spray (CS).

The Effect of Surface Roughness and Deposition Time on the Biocompatibility of Electrodeposited Hydroxyapatite Coating on Grit-Blasted AZ31B Mg Alloy

The Effect of Surface Roughness and Deposition Time on the Biocompatibility of Electrodeposited Hydroxyapatite Coating on Grit-Blasted AZ31B Mg Alloy