Hydrophobic Polydimethylsiloxane Research Articles

Diels-Alder Network Blends as Self-Healing Encapsulants for Liquid Metal-Based Stretchable Electronics.

Two dynamic covalent networks based on the Diels-Alder reaction were blended to exploit the properties of the dissimilar polymer backbones. Furan-functionalized polyether amines based on poly(propylene oxide) (PPO) FD4000 and polydimethylsiloxane (PDMS) FS5000 were mixed in a common solvent and reversibly cross-linked with the same bismaleimide DPBM. The morphology of the phase-separated blends is primarily controlled by the concentration of backbones. Increasing the PDMS content of the blends results in a dilute droplet morphology at 25 wt %, with a growing size and concentration of droplets and the formation of two separate PPO- and PDMS-rich layers at 50 wt %. Further increasing the PDMS content to 75 wt % leads to larger droplets and a thicker layer of the secondary phase. The hydrophobic PDMS phase creates a barrier against water, while the more hydrophilic PPO phase enhances the resistance against oxygen diffusion. Lowering the maleimide-to-furan stoichiometric ratio resulted in a decrease in cross-link density and thus more flexible and stretchable encapsulants. Changes in the stoichiometric ratio also affected the phase morphology due to resulting changes in phase separation and network formation kinetics. Lowering the stoichiometric ratio also resulted in enhanced self-healing properties of 96% at room temperature as a consequence of the increased chain mobility in the blended networks. The self-healing blends were used to encapsulate liquid metal circuits to create stretchable strain sensors with a linear electro-mechanical response without much drift or hysteresis, which could be efficiently recovered by 90% after the damage-healing cycles.

Flexible Janus Black Silicon Photothermal Conversion Membranes for Highly Efficient Solar-Driven Interfacial Water Purification.

Photothermal conversion materials are critical in the development of solar-driven interfacial evaporation techniques; however, achieving a high energy conversion efficiency remains challenging owing to the high cost and instability of light-absorbing materials, in addition to the difficulties of simultaneously improving light absorption while suppressing heat loss. A black silicon (Si) powder with a porous structure was prepared by chemical etching of a low-cost commercial micron-sized Al-Si alloy, and a flexible Janus black Si photothermal conversion membrane was constructed. The partially broken spherical particles and porous structure obtained after etching enhanced the refraction of light from the Si powder, imparting the prepared membrane with an average light absorption rate of 95.95% over the solar spectrum. Evaporation from the membrane increased the intermediate water content and reduced the equivalent evaporation enthalpy. The thermal conduction loss was inhibited through a one-dimensional water transport structure, and the membrane achieved a water evaporation rate of 2.17 kg m-2 h-1 and a photothermal efficiency of 94.95% under 1 sun illumination. Benefiting from the broadband absorption and high photothermal efficiency of black Si powder, surface modification of hydrophobic polydimethylsiloxane, and directional salt-out structure design, the evaporation rate of the Janus black Si membrane-based system in a 10% NaCl solution was maintained >2.10 kg m-2 h-1 after 7 days of continuous evaporation cycles. The removal rate of metal ions from simulated seawater and from practical wastewater containing complex heavy metals reached >99.9%, indicating the promising potential of black Si membrane for application in solar-driven interfacial water purification.

Ultra-small gold nanoparticles embedded cyclodextrin metal-organic framework composite membrane to achieve antibacterial and humidity-responsive functions

Cyclodextrin metal-organic framework (CD-MOF) is an edible and porous material that can serve as a template for synthesizing small-sized metal nanoparticles. However, its highly hydrophilic nature has limited its wider application. Herein, ultra-small gold nanoparticles (U-AuNPs) were loaded into CD-MOF to produce a composite material Au@CD-MOF. The CD-MOF was utilized as a template to control the size of the AuNPs. The synthesized Au@CD-MOF was easily dispersible in aqueous medium and its released U-AuNPs exhibited effective water dispersion stability within 120 days. Additionally, compared to gold nanoparticles prepared using traditional methods (T-AuNPs), the U-AuNPs exhibited superior antibacterial properties. Furthermore, hydrophilic Au@CD-MOF was incorporated into a hydrophobic polydimethylsiloxane (PDMS) matrix (Au@CD-MOF/PDMS) to achieve a humidity-responsive antibacterial function. The composite membrane exhibited remarkable responsiveness to humidity, showing almost no release of U-AuNPs at 0 % humidity. However, it exhibited approximately 89 % release within 1 h, and complete release of U-AuNPs was observed within 4 h under 100 % humidity. These findings highlight the successful preparation of a humidity-responsive antibacterial composite membrane, which has great potential applications in various scenarios, particularly in the field of antibacterial food packaging.

Extrusion Printing of Surface-Functionalized Metal-Organic Framework Inks for a High-Performance Wearable Volatile Organic Compound Sensor.

Wearable sensors hold immense potential for real-time andnon-destructive sensing ofvolatile organic compounds (VOCs), requiring both efficient sensing performance and robust mechanical properties. However, conventional colorimetric sensor arrays, acting as artificial olfactory systems for highly selective VOC profiling, often fail to meet these requirements simultaneously. Here, a high-performance wearable sensor array for VOC visual detection is proposed by extrusion printing of hybrid inks containing surface-functionalized sensing materials. Surface-modified hydrophobic polydimethylsiloxane (PDMS) improves the humidity resistance and VOC sensitivity of PDMS-coated dye/metal-organic frameworks (MOFs) composites. It also enhances their dispersion within liquid PDMS matrix, thereby promoting the hybrid liquid as high-quality extrusion-printing inks. The inks enable direct and precise printing on diverse substrates, forming a uniform and high particle-loading (70 wt%) film. The printed film on a flexible PDMS substrate demonstrates satisfactory flexibility and stretchability while retaining excellent sensing performance from dye/MOFs@PDMS particles. Further, the printed sensor array exhibits enhanced sensitivity to sub-ppm VOClevels, remarkable resistance to high relative humidity (RH) of 90%, and the differentiation ability for eight distinct VOCs. Finally, the wearable sensor proves practical by in situ monitoring of wheat scab-related VOC biomarkers. This study presents a versatile strategy for designing effective wearable gas sensors with widespread applications.

Hydrophobic and Luminescent Polydimethylsiloxane PDMS-Y2O3:Eu3+ Coating for Power Enhancement and UV Protection of Si Solar Cells.

Solar cells have been developed as a highly efficient source of alternative energy, collecting photons from sunlight and turning them into electricity. On the other hand, ultraviolet (UV) radiation has a substantial impact on solar cells by damaging their active layers and, as a result, lowering their efficiency. Potential solutions include the blocking of UV light (which can reduce the power output of solar cells) or converting UV photons into visible light using down-conversion optical materials. In this work, we propose a novel hydrophobic coating based on a polydimethylsiloxane (PDMS) layer with embedded red emitting Y2O3:Eu3+ (quantum yield = 78.3%) particles for UV radiation screening and conversion purposes. The favorable features of the PDMS-Y2O3:Eu3+ coating were examined using commercially available polycrystalline silicon solar cells, resulting in a notable increase in the power conversion efficiency (PCE) by ~9.23%. The chemical and UV stability of the developed coatings were assessed by exposing them to various chemical conditions and UV irradiation. It was found that the developed coating can endure tough environmental conditions, making it potentially useful as a UV-protective, water-repellent, and efficiency-enhancing coating for solar cells.

Regenerative Superhydrophobic Coatings for Enhanced Performance and Durability of High-Voltage Electrical Insulators in Cold Climates.

Superhydrophobic coatings can be a suitable solution for protecting vulnerable electrical infrastructures in regions with severe meteorological conditions. Regenerative superhydrophobicity, the ability to regain superhydrophobicity after being compromised or degraded, could address the issue of the low durability of these coatings. In this study, we fabricated a superhydrophobic coating comprising hydrophobic aerogel microparticles and polydimethylsiloxane (PDMS)-modified silica nanoparticles within a PDMS matrix containing trifluoropropyl POSS (F-POSS) and XIAMETER PMX-series silicone oil as superhydrophobicity-regenerating agents. The fabricated coating exhibited a static contact angle of 169.5° and a contact angle hysteresis of 6°. This coating was capable of regaining its superhydrophobicity after various pH immersion and plasma deterioration tests. The developed coating demonstrated ice adhesion as low as 71.2 kPa, which remained relatively unchanged even after several icing/de-icing cycles. Furthermore, the coating exhibited a higher flashover voltage than the reference samples and maintained a minimal drop in flashover voltage after consecutive testing cycles. Given this performance, this developed coating can be an ideal choice for enhancing the lifespan of electrical insulators.

Design of fluorine-free superhydrophobic silk fabrics with mechanical durability and self-cleaning properties for oil-water separation

The separation of oil and water can be effectively addressed through the application of superhydrophobic coatings. This method, known for enhancing the self-cleaning, anti-corrosive, and friction-reducing properties of materials, typically employs fluorine reagents to ensure the durability of the coating nanostructure. However, the use of fluorine reagents raises concerns related to health and the environment. We present a straightforward and efficient approach to fabricate a robust, fluorine-free superhydrophobic composite coating. The coating solution, comprised of hydrophobic silica nanoparticles and polydimethylsiloxane (PDMS), is formed through sonication. The resulting superhydrophobic coating is effortlessly applied to silk fabric through immersion and subsequent drying/curing. micrograph confirms the creation of porous micro/nanostructures on the silk fabric's surface. Exceptional superhydrophobicity is demonstrated with a water contact angle (WCA) of 161 °±1.5 ° and a small sliding angle (SA) of 5 °±0.5 °. The coating's firmness, durability, and UV resistance are assessed through 20 cycles of sandpaper friction (load 200 g) and repeated tape peeling tests. Furthermore, the modified silk fabrics exhibit excellent capabilities in oil-water separation. This fluorine-free superhydrophobic coating, characterized by its robustness, environmental friendliness, and ease of manufacture, holds promising applications in the textile industry.

Highly efficient solar-thermal-electric conversion based on asymmetric binary-architecture design in solid-solid composite phase change materials

The application of phase change materials (PCMs) in solar-thermal conversion is largely limited by the inherently inferior thermal conductivity (TC) and poor solar-thermal energy transition capacity of PCMs. Herein, 1,1,1-tri(hydroxymethyl)ethane@melamine foam/cellulose nanofiber/graphene nanoplate (TME@MCGx) shape-stable composite PCMs (ss-CPCMs) are prepared by encapsulating TME into MCGx aerogels. Profited by the effective heat-conducting MCG25 networks, the resulting TME@MCG25 ss-CPCM achieves high TC of 0.73 Wm-1k−1 for internal heat conduction. Meanwhile, the combination of surface photothermal etching and hydrophobic polydimethylsiloxane (PDMS) coating endows the obtained T-TME@MCG25 highly efficient solar-thermal conversation efficiency of 93.1 %, arising from the exposed 3D MCG25 skeletons for absorbing sunlight and the thin PDMS layer for preventing the absorbed solar-thermal energy from radiating and dissipating. Consequently, the solar-thermal-electric (STE) conversion system equipped with T-TME@MCG25 generates the prominent output voltage of 213.0 mV and current of 37.6 mA. Furthermore, the acquired T-TME@MCG25 exhibits remarkable hydrophobicity and self-cleaning performances, due to the micro-nano structures of MCGx skeleton surfaces and the low surface energy of PDMS coating. The design strategy of asymmetric binary-architecture containing 3D photothermal absorption layer and water repellency layer provides a valuable insight into STE energy conversion associated with hydrophobic ss-CPCMs, which can alleviate the looming energy crisis.

Durable superhydrophobic coating based on halloysite nanotubes for versatile oil/water separation and reusable water collection

Fog water collection gains increasing attention for harvesting atmospheric water to solve the water resource crisis in arid or semi-arid areas. In this work, a durable superhydrophobic coating based on halloysite nanotubes (HNT) for water collection is fabricated by introducing 1H,1H,2H,2H-perfluorodecyl trimethoxysilane (PFTS) modified HNT into a hydrophobic polydimethylsiloxane (PDMS) coating to construct a rough and superhydrophobic surface. The dip-coating method is employed to apply the coatings onto various substrates. The surface wettability, water collection rate, mechanical stability, and durability, oil/water separation efficiency and flux, and oil absorption capacity are investigated in detail. When the content of fluorinated modified HNT (F-HNT) is 15 %, superhydrophobic F-HNT@PDMS coated fabrics with a high water contact angle (157.3°) as well as a low sliding angle (3.7°) are obtained, and the treated fabrics show excellent self-cleaning ability. After 100 mechanical wear cycles, the coated fabrics remain superhydrophobicity, and the oil/water separation efficiency is maintained above 99.5 %. Furthermore, different substrates dip-coated with F-HNT@PDMS exhibit high-efficiency water collection rates of 952.25–1058.5 mg∙cm−2∙h−1. Therefore, this work provides a feasible strategy for preparing a durable superhydrophobic coating with a high-efficiency water collection rate and is expected to be applied in fog water harvesting in scarce areas.

Transparent PDMS Surfaces with Covalently Attached Lubricants for Enhanced Anti-adhesion Performance.

Liquid-like surfaces featuring slippery, omniphobic, covalently attached liquids (SOCALs) reduce unwanted adhesion by providing a molecularly smooth and slippery surface arising from the high mobility of the liquid chains. Such SOCALs are commonly prepared on hard substrates, such as glass, wafers, or metal oxides, despite the importance of nonpolar elastomeric substrates, such as polydimethylsiloxane (PDMS) in anti-fouling or nonstick applications. Compared to polar elastomers, hydrophobic PDMS elastomer activation and covalent functionalization are significantly more challenging, as PDMS tends to display fast hydrophobic recovery upon activation as well as superficial cracking. Through the extraction of excess PDMS oligomers and fine-tuning of plasma activation parameters, homogeneously functionalized PDMS with fluorinated polysiloxane brushes could be obtained while at the same time reducing crack formation. Polymer brush mobility was increased through the addition of a smaller molecular silane linker to exhibit enhanced dewetting properties and reduced substrate swelling compared to functionalizations featuring hydrocarbon functionalities. Linear polymer brushes were verified by thermogravimetric analysis. The optical properties of PDMS remained unaffected by the activation in high-frequency plasma but were impacted by low-frequency plasma. Drastic decreases in solid adhesion of not just complex contaminants but even ice could be shown in horizontal push tests, demonstrating the potential of SOCAL-functionalized PDMS surfaces for improved nonstick applications.

Hydrophobic MOF/PDMS-Based QCM Sensors for VOCs Identification and Quantitative Detection in High-Humidity Environments.

Metal-organic frameworks (MOFs) have great potential in quartz crystal microbalance (QCM) platforms for volatile organic compound (VOCs) detection and recognition due to their unique properties. However, the MOFs' hydrophilicity degrades performance in high-humidity environments, limiting reliable VOC sensing in complex environments. Herein, we propose a novel VOC virtual sensor array (VSA) using a single QCM sensor with an adsorption layer composed of MIL-101(Cr) MOF and polydimethylsiloxane (PDMS), realizing stable sensing and accurate identification for different VOCs under various relative humidity (RH) conditions. The hydrophobic PDMS layer improves the moisture resistance of the sensor to 4 and 14 times in terms of shifts in resonant frequency and scattering parameters, respectively. In addition, performance is maintained over 2 days of water treatment, demonstrating superior water resistance. The highest sensitivity of 2.68 mdB ppm-1 is achieved for isopropanol detection, with the lowest limit of detection of 20.06 ppm for acetone. Combining resonant signals and lumped parameters, the proposed VSA technique effectively discriminates four VOCs (ethanol, 2-propanol, acetone, and acetonitrile) with a high accuracy of 95.3% under both 60% and 90% RH backgrounds. The studies provide a promising solution for reliable low-concentration VOC detection using QCM sensors in high-humidity environments such as underground spaces.

Facile preparation of hydrophobic polydimethylsiloxane based reusable oil-absorbents for effective oil/water separation

Water pollution due to oil drilling, human mistakes, tanker accidents, and natural disasters have severely affected humanity. A rapid removal of such pollutants from the environment should be a priority. In this paper, polydimethylsiloxane-based polymer sorbents have been fabricated by using carbinol terminated polydimethylsiloxane (PDMS) and organosilicon cross-linker via the one-pot bulk polymerization method. The preparation method does not require any activator, solvent, initiator, or catalyst. Obtained cross-linked sorbents have a high interest in organic liquids and oils, while no interest in water mediums. Absorption kinetics also show that they can quickly absorb the oil into their porous structure in a short time, implying their effective use in sudden oil leakages. They can selectively absorb the oil from different water mediums repeatedly used without any significant capacity loss. The output demonstrated that PDMS-based cross-linked polymers could be effectively utilized as sorbents in the event of oil spillage in order to absorb the spilled oil from wastewater.

Construction of lignin/CaCO3/CS superhydrophobic coating with excellent heat resistance, abrasion resistance, UV resistance and oil-water separation

Superhydrophobic coatings are developed rapidly due to the eye-catching versatility, but still suffer from problems of insufficient environmental protection, poor heat resistance, and weak UV resistance. Here, a stable and versatile lignin/calcium carbonate (CaCO3)/chitosan (CS) superhydrophobic coating on the wood (beech) could be successfully prepared by simple one-step spay. In the coating system, enzymolysis lignin was employed as the main materials to construct surface rough structure, which was enhanced with both CaCO3 and CS, methyltrimethoxysilane (MTMS) and hexadecyltrimethoxysilane (HDTMS) as the hydrophobic modifiers and polydimethylsiloxane (PDMS) as the adhesive. The resulted coating shows good superhydrophobicity (water contact angle of 161.1° and sliding angle of 8°), as well as excellent heat resistance (superhydrophobicity still maintaining under 200 °C), UV resistance (10 h of high-intensity UV irradiation). In addition, when PU sponge was used as the substrate, the stable oil-water separation could be achieved. In view of the good performance and simple preparation, the superhydrophobic coating displays a good application prospect.

Fabrication of high-aspect-ratio metallic microstructures by microelectroforming using silver-coated polydimethylsiloxane molds with controllable wettability

Abstract Microelectroforming is a specialized electroplating process to prepare functional metallic microstructures. However, the formability of microelectroforming is usually restricted by the limited mass transfer in high-aspect-ratio microcavities of molds. This paper presents a simple and reliable method utilizing silver (Ag)-coated polydimethylsiloxane (PDMS) molds with controllable wettability to enhance the formability of microelectroforming. The surfaces of these molds exhibited reversible water contact angles ranging from 4° to 151° realized through ultraviolet irradiation and heat treatment. The hydrophilicity of the PDMS molds facilitated liquid-phase mass transfer, contributing to the fabrication of complete and defect-free nickel microstructures with high aspect ratios. Subsequently, the hydrophobic PDMS molds reduced the interfacial adhesion between these molds and nickel microstructures, which was beneficial for perfect demolding. Nickel microstructures with an aspect ratio of 10 can be achieved by using the PDMS molds, which significantly enhance the formability of microelectroforming. This method provides a potential method to prepare high-aspect-ratio metallic microstructures.

Fast-Crosslinking Enabled Self-Roughed Polydimethylsiloxane Transparent Superhydrophobic Coating and Its Application in Anti-Liquid-Interference Electrothermal Device.

Polydimethylsiloxane (PDMS)-based transparent and superhydrophobic coatings have important applications, such as anti-icing, corrosion resistance, self-cleaning, etc. However, their applications are limited by the inevitable introduction of nanoparticles/high-temperature/segmented PDMS to facilitate a raspy surface. In this study, a self-roughed, neat PDMS superhydrophobic coating with high transparency is developed via a one-step spray-coating technique. PDMS suspensions with various droplet sizes are synthesized and used as building blocks for raspy surface formation by controlled curing on the warm substrate. The optimal coating exhibits a large water contact angle of 155.4° and transparency (T550 = 82.3%). Meanwhile, the employed spray-coating technique is applicable to modify a plethora of substrates. For proof-of-concept demonstrations, the use of the PDMS hydrophobic coating for anti-liquid-interference electrothermal devices and further transparent observation window for long-term operation in a sub-zero environment is shown successful. The proposed facile synthesis method of hydrophobic PDMS coating is expected to have great potential for a broad range of applications in the large-scale fabrication of fluorine-free, eco-friendly superhydrophobic surfaces.

Self-heating, elastic, hydrophobic wood sponge for recovering spilled crude oil under sunlight and microwave dual stimuli

Water pollution caused by crude oil spills poses significant environmental concerns. In this work, multi-walled carbon nanotubes (MWCNTs) were dispersed as the carbon network on the elastic wood sponge (WS) and then encapsulated by hydrophobic polydimethylsiloxane (PDMS) coating to form a crude oil adsorbent, PDMS@CNT-WS. It demonstrated an elasticity of up to 90% compressive strain, while the height retention remained at 97% even after 100 cycles at 50% compressive strain. The shape-memory properties and 148°hydrophobic angle of the material allowed it to be repeatedly used. This is the first material to utilize sunlight and microwave as dual stimuli to absorb and recover spilled crude oil. PDMS@CNT-WS absorbed crude oil floating on water within about 80 s under 1 sun illumination. After condensation, the material was heated within only 4 s in a microwave oven at 2450 MHz, and the crude oil in the interior could be recovered by simply squeezing the material. This new approach provided a source of energy conversion for crude oil adsorbents with thermal management capabilities to clean up crude oil spills.

Covalent bonding of quaternary ammonium compounds and zwitterionic polymer functional layers on polydimethylsiloxane against Escherichia Coli adhesion.

Quaternary ammonium compounds (QACs) are recognized by the World Health Organization as a useful disinfectant against microbes. The synergistic effect of zwitterionic polymers with QACs as antimicrobial agents rather than QACs alone is yet to be investigated. A potential strategy is the use of covalent bonding to halt the release of minute antibacterials and a hierarchy of functional layers to detain and annihilate microbes. The strategy was tested on a polydimethylsiloxane (PDMS) surface on which quaternized poly(2-dimethylaminoethyl methacrylate) (qDMA+) and sulfobetaine (SBMA) were hierarchically functionalized. Attenuated total reflectance Fourier transform infrared analysis confirmed the quaternization of DMA to qDMA+, grafting of qDMA + on PDMS (PDMS-qDMA+), and grafting of the SBMA overlayer on PDMS-qDMA+ (PDMS-qDMA+-SB). Contact angle measurement showed that PDMS-qDMA + exhibited the lowest contact angle (26.2 ± 2.9°) compared with the hydrophobic PDMS (115.2 ± 1.6°), but that of PDMSqDMA+-SB increased to 56.3 ± 1.3°. The Escherichia coli survival count revealed that PDMS-qDMA+ and PDMS-qDMA+-SB exhibited significantly greater bactericidal ability than PDMS. Confocal laser scanning microscopy revealed fewer dead bacteria on PDMS-qDMA+-SB than on PDMS-qDMA+. Scanning electron microscopy demonstrated that E. coli was disintegrated on the functionalized surface via dual-end cell lysis. To the best of our knowledge, this is the first observation of this type of process. The results confirmed the potent antibacterial and cell disruption activities of the qDMA+ and SBMA modified PDMS surface.

Asymmetric Triple-Functional Janus Membrane for Blood Oxygenation.

The oxygenation membrane, a core material of extracorporeal membrane oxygenation (ECMO), is facing challenges in balancing anti-plasma leakage, gas exchange efficiency, and hemocompatibility. Here, inspired by the asymmetric structural features of alveolus pulmonalis, a novel triple-functional membrane for blood oxygenation with a Janus architecture is proposed, which is composed of a hydrophobic polydimethylsiloxane (PDMS) layer to prevent plasma leakage, an ultrathin polyamide layer to enhance gas exchange efficiency with a CO2 :O2 permeance ratio of ≈10.7, and a hydrophilic polyzwitterionic layer to improve the hemocompatibility. During the simulated ECMO process, the Janus oxygenation membrane exhibits excellent performance in terms of thrombus formation and plasma leakage prevention, as well as adequate O2 transfer rate (17.8 mL min-1 m-2 ) and CO2 transfer rate (70.1 mL min-1 m-2 ), in comparison to the reported oxygenation membranes. This work presents novel concepts for the advancement of oxygenation membranes and demonstrates the application potential of the asymmetric triple-functional Janus oxygenation membrane in ECMO.

Breaking The Permeance-Selectivity Tradeoff for Post-Combustion Carbon Capture: A Bio-Inspired Strategy to Form Ultrathin Hollow Fiber Membranes.

Thin film composite (TFC) hollow fiber membranes with ultrathin selective layer are desirable to maximize the gas permeance for practical applications. Herein, a bio-inspired strategy is proposed to fabricate sub-100-nm membranes via a tree-mimicking polymer network with amphipathic components featuring multifunctionalities. The hydrophobic polydimethylsiloxane (PDMS) brushes act as the roots that can strongly cling to the gutter layer, the PDMS crosslinkers function as the xylems to enable fast gas transport, and the hydrophilic ethylene-oxide moieties (brushes and mobile molecules) resemble tree leaves that selectively attract CO2 molecules. As a result, a ≈27nm-thick selective layer can be attached to the hollow fiber-supported PDMS gutter layer through a simple dip-coating method without any modification. Furthermore, a CO2 permeance of ≈2700 GPU and a CO2 /N2 selectivity of ≈21 that is beyond the permeance-selectivity upper bound for hollow fiber membranes is achieved. This bio-inspired concept can potentially open the possibility of scalable hollow fiber membranes production for commercial applications in post-combustion carbon capture and beyond.

Development of self-cleaning superhydrophobic cotton fabric through silica/PDMS composite coating

The lotus effect informs that self-cleaning superhydrophobic surfaces can be obtained by creating rough surface structures and modifying them with chemicals that have low surface energy. Herein, the composite of hydrophobic silica nanoparticles (SNPs) and polydimethylsiloxane (PDMS) was deposited on cotton fabric by multiple dip cycles. At optimal condition, the agglomerated SNPs in PDMS produces a hierarchical rough surface, as a result the coated cotton fabric has revealed a water contact angle (WCA) of 158.41 ± 1.58° and 4° of sliding angle. Due to negligible water adhesion to a superhydrophobic surface, coated cotton fabric reveals excellent self-cleaning behavior, which was tested by dust particles, muddy water and tea droplets. Furthermore, coated cotton fabric sustains superhydrophobicity over the mechanical robustness tests including adhesive tape peeling test, sandpaper abrasion test, and ultrasonication. Therefore, such an approach may be applicable in textile industries for self-cleaning purposes.