Detection Of Peroxide Research Articles

Highly Sensitive Detection of Hydrogen Peroxide in Cancer Tissue Based on 3D Reduced Graphene Oxide-MXene-Multi-Walled Carbon Nanotubes Electrode.

Hydrogen peroxide (H2O2) is a signaling molecule that has the capacity to control a variety of biological processes in organisms. Cancer cells release more H2O2 during abnormal tumor growth. There has been a considerable amount of interest in utilizing H2O2 as a biomarker for the diagnosis of cancer tissue. In this study, an electrochemical sensor for H2O2 was constructed based on 3D reduced graphene oxide (rGO), MXene (Ti3C2), and multi-walled carbon nanotubes (MWCNTs) composite. Three-dimensional (3D) rGO-Ti3C2-MWCNTs sensor showed good linearity for H2O2 in the ranges of 1-60 μM and 60 μM-9.77 mM at a working potential of -0.25 V, with sensitivities of 235.2 µA mM-1 cm-2 and 103.8 µA mM-1 cm-2, respectively, and a detection limit of 0.3 µM (S/N = 3). The sensor exhibited long-term stability, good repeatability, and outstanding immunity to interference. In addition, the modified electrode was employed to detect real-time H2O2 release from cancer cells and cancer tissue ex vivo.

Tailored electrochemical biosensor with poly-diallydimethylammonium chloride-functionalised multiwalled carbon nanotubes/gold nanoparticles/manganese dioxide, and haemoglobin for sensitive hydrogen peroxide detection

A very sensitive electrochemical biosensor, with haemoglobin (Hb) as its basis, has been created to quantify hydrogen peroxide (H2O2), an essential marker in environmental monitoring, food safety, and medical diagnosis. The sensor uses a simple, eco-friendly preparation method. Hb was immobilised on manganese dioxide nanostructure/gold nanoparticles/poly-diallydimethylammonium chloride-functionalised multiwalled carbon nanotubes (PDDA-MWCNT/AuNP/MnO2), characterised using various techniques: amperometry, voltammetry, X-ray diffraction (XRD), and transmission electron microscopy (TEM). Nafion was used as a binder membrane to preserve the biological and electrochemical properties of the protein on the modified electrode. In comparison to earlier research, the novel biosensor had a lower detection limit (1.83 μM) and a limit of quantification (6.11 μM) (S/N = 3) for H2O2. It also exhibited notable reproducibility, long-term stability, and repeatability. It was effectively used to measure the amount of H2O2 in cow milk and orange juice, yielding recoveries in the order of 98.90–99.53 % with RSDs less than 5.0 %, which makes it a promising biosensor for food control.

Pseudomonas syringae pv. tomato DC3000 Induces Defense Responses in Diverse Maize Inbred Lines

Many phytopathogens translocate virulence (effector) proteins into plant cells to circumvent host immune responses during infection. One such pathogen is Pseudomonas syringae pv. tomato DC3000, which secretes at least 29 effectors into host cells, of which a subset elicits host defense responses in crop plant species. However, it is unknown whether P. syringae pv. tomato DC3000 activates immune responses in diverse maize inbreds. Here, we screened a diverse maize germplasm collection for effector-dependent recognition of this bacterial pathogen. As a control, we infiltrated P. syringae DC3000(D36E), a derivative of P. syringae pv. tomato DC3000 that lacks all endogenous effectors. In our evaluations, we observed a variety of responses to P. syringae pv. tomato DC3000 in maize and scored the phenotypes as either having no observable response (N) or exhibiting one of three responses: weak chlorosis (WC), chlorosis (C) with minimal cell death, and hypersensitive reaction (HR)-like cell death. Of the 26 maize inbreds screened, 13 were scored as N, 2 as WC, 2 as C, and 9 as HR-like cell death. Importantly, no maize line responded to P. syringae DC3000(D36E), demonstrating that the responses observed are likely dependent on recognition of one or more Pseudomonas effectors. Furthermore, the maize inbreds that recognize P. syringae pv. tomato DC3000 accumulated detectable hydrogen peroxide as well as an increase in transcript expression of a subset of maize defense genes. Collectively, our results will likely stimulate new research aimed at identifying the cognate maize disease resistance proteins that recognize the activities of one or more bacterial effectors. [Formula: see text] Copyright © 2024 The Author(s). This is an open access article distributed under the CC BY-NC-ND 4.0 International license .

The impact of hollow core-shell nanozymes in biosensing: A case study of p-Fe3O4@PDA@ZIF-67

BackgroundNanozymes, a new class of nanomaterials, have emerged as promising substitutes for enzymes in biosensor design due to their exceptional stability, affordability, and ready availability. While nanozymes address many limitations of natural enzymes, they still face challenges, particularly in achieving the catalytic activity levels of their natural counterparts. This indicates the need for enhancing the sensitivity of biosensors based on nanozymes. The catalytic activity of nanozyme can be significantly improved by regulating its size, morphology, and surface composition of nanomaterial. ResultsIn this work, a kind of hollow core-shell structure was designed to enhance the catalytic activity of nanozymes. The hollow core-shell structure material consists of a nanozymes core layer, a hollow layer, and a MOF shell layer. Taking the classic peroxidase like Fe3O4 as an example, the development of a novel nanozyme@MOF, specifically p-Fe3O4@PDA@ZIF-67, is detailed, showcasing its application in enhancing the sensitivity of sensors based on Fe3O4 nanozymes. This innovative nanocomposite, featuring that MOF layer was designed to adsorb the signal molecules of the sensor to improve the utilization rate of reactive oxygen species generated by the nanozymes catalyzed reactions and the hollow layer was designed to prevent the active sites of nanozymes from being cover by the MOF layer. The manuscript emphasizes the nanocomposite's remarkable sensitivity in detecting hydrogen peroxide (H2O2), coupled with high specificity and reproducibility, even in complex environments like milk samples. Significance and noveltyThis work firstly proposed and proved that Fe3O4 nanozyme@MOF with hollow layer structure was designed to improve the catalytic activity of the Fe3O4 nanozyme and the sensitivity of the sensors based on Fe3O4 nanozyme. This research marks a significant advancement in nanozyme technology, demonstrating the potential of structural innovation in creating high-performance, sensitive, and stable biosensors for various applications.

A Novel MXene@MOF@Pt NPs-Based Enzyme-Free Electrochemical Sensor for Highly Sensitive Detection of Hydrogen Peroxide Released from Living Cells

Rapid and accurate detection of hydrogen peroxide (H2O2), an important reactive oxygen species (ROS) released from living cells, is of great significance for early diagnosis of tumors. Here, a high sensitive enzyme-free electrochemical sensor for the detection of H2O2 released from living cells was constructed based on MXene@ZIF-8@Pt NPs nanocomposites. Through the characterization of physical and chemical properties, it was observed that Pt NPs with excellent catalytic activity were uniformly supported on MXene@ZIF-8, which exhibited excellent conductivity and large specific surface area. Thanks to the significantly enhanced catalytic activity derived from the successful integration of MXene, ZIF-8 and Pt NPs, under the optimal conditions, the sensing platform based on MXene@ZIF-8@Pt NPs exhibited a wide linear range from 355.4 nM to 21.75 mM, with a limit of detection as low as 120.9 nM, while showing satisfactory reproducibility and selectivity. Furthermore, the developed electrochemical sensor enables real-time monitoring of H2O2 released from living Hela cells under N-formylmethionyl-leucyl-phenylalanine stimulation. Overall, the MXene@ZIF-8@Pt NPs developed in this article will become a promising candidate in monitoring physiological processes.

A Review on the Development of Polymer Supported Heterogeneous Palladium Materials for Organic Synthesis and Electrochemical Applications

Abstract:: This comprehensive review explores the advancements in catalytic transformation, focusing on the use of heterogeneous catalytic systems with a particular emphasis on polymeric-supported palladium (Pd) complexes. This study explores the limitations associated with conventional homogeneous reagents, emphasizes the transition to eco-friendly catalytic systems, and emphasizes the importance of Pd nanoparticles. These nanoparticles are particularly noteworthy for their distinctive properties, including elevated catalytic activity, making them promising for various applications in organic synthesis. The review thoroughly examines the design and synthesis of heterogeneous catalysts, emphasizing the crucial selection of safe and recyclable supports to augment the longevity and reusability of metallic catalysts. Diverse polymer varieties, including polystyrene (PS), polyethylene (PE), polyacrylate derivatives, polyethylene glycol (PEG), and grafted polymers, are investigated as viable supports for Pd complexes. The authors intricately describe the synthesis techniques for these polymer-supported Pd catalysts and furnish illustrative examples showcasing their effectiveness in organic transformation. This comprehensive review additionally highlights the synthesis of polymer-supported palladium (Pd) materials and discusses their applications in electrochemistry. The focus extends to the electrocatalytic properties of Pdbased polymeric nanomaterials, showcasing their effectiveness in glucose sensing, hydrogen peroxide detection, and the sensing of other biological analytes. Furthermore, the catalytic capabilities of Pd nanoparticles in various electrochemical applications, including wastewater treatment and electrochemical capacitors, are explored. Integrating polymer-supported Pd materials into these electrochemical processes underscores their versatility and potential contributions to advancements in catalysis and electrochemical sensing. Catalytic applications featuring polymer-supported palladium complexes with polymeric ligands in organic synthesis processes use the Sonogashira reaction, Suzuki-Miyaura coupling, Heck reaction, Catalytic asymmetric transformations, etc. The subsequent section of the paper focuses on the creation of polymeric palladium complexes, achieved by the complexation of polymeric ligands with palladium precursors. It delves into noteworthy examples of catalytic processes employing polymer-supported palladium complexes featuring polymeric ligands, emphasizing distinct polymers, such as PS, PE, polyacrylate derivatives, PEG, and grafting polymers. The review concludes by exploring catalytic asymmetric transformations using chiral palladium complexes immobilized on polymer supports and discusses various chiral ligands and their immobilization on polymer supports, emphasizing their application in asymmetric allylic alkylation. The review furnishes a comprehensive summary of recent advancements, challenges, and prospective avenues in catalytic oxidation facilitated by polymer- supported palladium catalysts with electrochemical applications.

Microwave hydrothermal synthesis of ascorbic acid derived nitrogen-doped carbon dots and its application in peroxide detection

Microwave hydrothermal synthesis of ascorbic acid derived nitrogen-doped carbon dots and its application in peroxide detection

Comparison of methods for the synthesis of silver nanoparticles stabilized in a solid polymethacrylate matrix

Silver nanoparticles were synthesized inside the small plates of transparent polymer medium by reduction of silver cations. The difference in morphology and sizes of nanoparticles synthesized by chemical, photochemical and thermal reduction was revealed, which depends both on the component ratio of the mixture and on the reduction time for the specific component ratio The polymethacrylate matrix itself acts as the stabilizing agent. A colorimetric sensor based on polymethacrylate matrix and silver nanoparticles was developed for the detection of hydrogen peroxide. The optical properties of the sensor were characterized by spectrophotometer using the surface plasmon resonance. A colorimetric sensor with nanoparticles undergoing to thermal reduction showed a quick result for the determination of hydrogen peroxide in the range 0.2–4.4 mM with a detection limit 0.1 mM.

Catalase‐functionalized ZnO and graphene oxide used as electrocatalyst for the selective detection of hydrogen peroxide

AbstractBACKGROUNDThis study focuses on the fabrication of a biosensor for the electrocatalytic and selective hydrogen peroxide (H2O2) recognition with bovine liver catalase (CAT) immobilized over a cysteine (c) modified zinc oxide nanoparticles/graphene oxide (c‐ZnO/GO) interface. The selectivity and sensitivity of the biosensor were augmented by the use of CAT and GO, respectively. The problem of CAT activity inhibition by GO was specifically solved by the incorporation of ZnO. Also, the cystine functionalization helped in better immobilization of CAT.RESULTSThis unique approach was first validated with in silico computations that calculated the binding affinities to study the interactions between different components of the biosensor. The electrochemical studies confirmed the step‐by‐step modification of the sensor, where along with GO, c‐ZnO nanoparticles also showed excellent electro‐conductivity by fundamentally improving the peak currents towards H2O2. The proposed bio‐nano interface exhibited superb electrocatalytic performance and specific detection capability for H2O2 across a broad linear range (0.1 to 40 μmol L−1), featuring a low detection limit (0.1 μmol L−1), as well as commendable reproducibility and storage durability. Furthermore, the biosensor yielded satisfactory outcomes for H2O2 detection in milk samples.CONCLUSIONSensing performance of nano‐bio interfaces can be augmented by using the appropriate nano‐composites and their efficacy confirmed through computational techniques such as molecular docking. The biosensor can be further repurposed into a wearable device by integration with lab‐on‐a‐chip platforms. © 2024 Society of Chemical Industry (SCI).

Ultrasensitive and specific photoelectrochemical sensor for hydrogen peroxide detection based on pillar[5]arene-functionalized Au nanoparticles and MWNTs hybrid BiOBr heterojunction.

A photoelectrochemical sensor for target detection of hydrogen peroxide was designed based on a new heterojunction nanocomposite which was sulfhydryl-borate ester-modified A1/B1-type pillar[5]arene (BP5)-functionalized Au NPs and multi-walled carbon nanotubes hybridized with bismuth bromide oxide (Au@BP5/MWNTs-BiOBr). The specific sensor was based on the direct induction of oxidation by hydrogen peroxide of the borate ester group of pillar[5]arene. Additionally, the local surface plasmon resonance (LSPR) of Au NPs enhanced visible light capture, the host-guest complexation of BP5 with H2O2 enhanced photocurrent response, the layer-by-layer stacked nanoflower structure of BiOBr provided large specific surface area with more active sites, and the conductivity of MWNTs enhanced the charge separation efficiency and significantly improves the stability of PEC. Their synthesis effect significantly increased the photocurrent signal and further enhanced the detection result. Under the optimal conditions, the linear concentration range of H2O2 detected by the Au@BP5/MWNTs-BiOBr sensor was from 1 to 60pmol/L. The limit of detection (LOD) and the limit of quantification (LOQ) of the method were 0.333pmol/L and 1pmol/L, respectively, and the sensitivity was 6.471pmol/L. Importantly, the PEC sensor has good stability, reproducibility, and interference resistance and can be used for the detection of hydrogen peroxide in real cells.

Iron-carbon dots embedded in molybdenum single-atom nanoflowers as multifunctional nanozyme for dual-mode detection of hydrogen peroxide and uric acid

Single-atom catalysts (SACs) have attracted extensive attention in the field of catalysis due to their excellent catalytic ability and enhanced atomic utilization, but the multi-mode single-atom nanozymes for biosensors remain a challenging issue. In this work, iron-doped carbon dots (Fe CDs) were loaded onto the edges and pores of Mo SACs with nanoflower morphology; accordingly, a composite material Fe CDs/Mo SACs was prepared successfully, which improves the catalytic performance and develops a fluorescence mode without changing the original morphology. The steady-state kinetic data indicates that the material prepared have better affinity for substrates and faster reaction rates under optimized conditions. The specific kinetic parameters Km and Vmax were calculated as 0.39 mM and 7.502×10−7 M·s−1 respectively. The excellent peroxidase-like activity of Fe CDs/Mo SACs allows H2O2 to decompose into •OH, which in turn oxidizes colorless o-phenylenediamine (OPD) to yellow 2,3-diaminophenazine (DAP). At the same time, the fluorescence signal of Fe CDs/Mo SACs quenches obviously by DAP at 460 nm through internal filtration effect (IFE), while the characteristic fluorescence response of DAP gradually increases at 590 nm. Based on this sensing mechanism, a sensitive and accurate dual-mode (colorimetric and ratiometric fluorescent) sensor was constructed to detect H2O2 and uric acid, and the rate of recovery and linearity were acceptable for the detection of UA in human serum and urine samples. This method provides a new strategy for rapid and sensitive detection of UA, and also broadens the development of SACs in the field of biosensors.

Crab gill–derived nanorod-like carbons as bifunctional electrochemical sensors for detection of hydrogen peroxide and glucose

Crab gill–derived nanorod-like carbons as bifunctional electrochemical sensors for detection of hydrogen peroxide and glucose

Intelligent salivary biosensors for periodontitis: in vitro simulation of oral oxidative stress conditions.

One of the most common oral diseases affecting millions of people worldwide is periodontitis. Usually, proteins in body fluids are used as biomarkers of diseases. This study focused on hydrogen peroxide, lipopolysaccharide (LPS), and lactic acid as salivary non-protein biomarkers for oxidative stress conditions of periodontitis. Electrochemical analysis of artificial saliva was done using Gamry with increasing hydrogen peroxide, bLPS, and lactic acid concentrations. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were conducted. From EIS data, change in capacitance and CV plot area were calculated for each test condition. Hydrogen peroxide groups had a decrease in CV area and an increase in percentage change in capacitance, lipopolysaccharide groups had a decrease in CV area and a decrease in percentage change in capacitance, and lactic acid groups had an increase of CV area and an increase in percentage change in capacitance with increasing concentrations. These data showed a unique combination of electrochemical properties for the three biomarkers. Scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) employed to observe the change in the electrode surface and elemental composition data present on the sensor surface also showed a unique trend of elemental weight percentages. Machine learning models using hydrogen peroxide, LPS, and lactic acid electrochemical data were applied for the prediction of risk levels of periodontitis. The detection of hydrogen peroxide, LPS, and lactic acid by electrochemical biosensors indicates the potential to use these molecules as electrochemical biomarkers and use the data for ML-driven prediction tool for the periodontitis risk levels.

Rapid aqueous preparation of carbon quantum dots and their application as nanozyme for the detection of hydrogen peroxide and uric acid

A green and rapid method was developed to synthesize a series of carbon quantum dots (Fe,N/CQDs, Fe,S/CQDs, S,N/CQDs and Fe,S,N/CQDs) through thermal decomposition using persimmon frost as a carbon source. All the synthesized CQDs have peroxidase-like activity, and the comparision of their steady-state kinetic parameters inferred that the peroxidase-like activity of Fe,S,N/CQDs is superior to those of Fe,S/CQDs and Fe,N/CQDs. Furthermore, Fe,S,N/CQDs exhibited good affinity towards 3,3′,5,5′-Tetramethylbenzidine (TMB) and H2O2 compared to natural horseradish peroxidase (HRP) and other nanozymes. In theory, uric acid (UA) can produce H2O2 with the catalysis by uricase. Fe,S,N/CQDs could catalyze the breakdown of H2O2 to produce reactive oxygen species (ROS), which can oxidize TMB (colorless) to oxTMB (blue). Based on the nanozyme-catalyzed oxidation of TMB, a simple and sensitive colorimetric sensor was developed for the quantitative analysis of H2O2 and UA. Low limit of detection (0.73 μM), wide linear range (1–80 μM) and good repeatability were obtained. The sensor was also demonstrated for the determination of UA in biological samples and satisfactory results were obtained.

Reticular Rare-Earth Metal–Organic Frameworks with High Stability and Defective Sites: Post-Functionalization for Hydrogen Peroxide Detection

Reticular Rare-Earth Metal–Organic Frameworks with High Stability and Defective Sites: Post-Functionalization for Hydrogen Peroxide Detection

A simple mitochondria-immobilized fluorescent probe for the detection of hydrogen peroxide

Hydrogen peroxide (H2O2), as one of reactive oxygen species (ROS) widely present in the human body, is involved in a variety of physiological activities. Many human diseases are associated with abnormal levels of H2O2 in the body. Mitochondria are the main organelles producing H2O2 in the human body, and monitoring the level of H2O2 in mitochondria can help to deepen the understanding of the detailed functions of H2O2 in physiological activities. However, due to the highly dynamic nature of the cells, real-time quantitative monitoring of H2O2 levels in mitochondria remains an ongoing challenge. Herein, a novel highly immobilized mitochondria-targeting fluorescent probe (QHCl) for detection of H2O2 was reasonably constructed based on quinolinium dye containing benzyl chloride moiety. Spectral experimental results demonstrated QHCl possessed outstanding selectivity toward H2O2 (λex/em = 380/513 nm). In addition, QHCl can quantitatively detect H2O2 in the concentration range of 0–20 μM with excellent sensitivity (LOD = 0.58 μM) under the PBS buffer solution (10 mM, pH = 7.4). Finally, bioimaging experiments demonstrated that the probe QHCl was able to be used for accurately detecting both endogenous and exogenous H2O2 in the mitochondria of living cells and zebrafish by its unique mitochondrial immobilization.

Controlled Synthesis of Preferential Facet-Exposed Fe-MOFs for Ultrasensitive Detection of Peroxides.

Exposing different facets on metal-organic frameworks (MOFs) is highly desirable to enhance the performance for various applications, however, exploiting a concise and effective approach to achieve facet-controlled synthesis of MOFs remains challenging. Here, by modulating the ratio of metal precursors to ligands, the facet-engineered iron-based MOFs (Fe-MOFs) exhibits enhanced catalytic activity for Fenton reaction are explored, and the mechanism of facet-dependent performance is revealed in detail. Fully exposed (101) and (100) facets on spindle-shaped Fe-MOFs enable rapid oxidation of colorless o-phenylenediamine (OPD) to colored products, thereby establishing a dual-mode platform for the detection of hydrogen peroxide (H2O2) and triacetone triperoxide (TATP). Thus, a detection limit as low as 2.06nm is achieved, and robust selectivity against a wide range of common substances (>16 types) is obtained, which is further improved by incorporating a deep learning architecture with an SE-VGG16 network model, enabling precise differentiation of oxidizing agents from captured images. The present strategy is expected will shine light on both the rational synthesis of nanomaterials with modulated morphologies and the exploitation of high-performance trace chemical sensors.

Au/Ag2MoO4 nanocomposite: A dual-function catalyst for dye degradation and colorimetric detection

The authors have successfully synthesized a distinctive potato-shaped Au/Ag2MoO4 nanocomposite with exceptional photocatalytic capabilities in the degradation of methylene blue (MB) under UV irradiation even in neutral conditions. Furthermore, this material displays noteworthy peroxidase-like oxidation activity, facilitating the detection of hydrogen peroxide (H2O2) and ascorbic acid (AA) in aqueous environments. This detection method relies on the oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB). The signal generated by TMB adsorption on the catalyst's surface plays a pivotal role in the oxidation of TMB in the presence of H2O2, resulting in the formation of a distinct blue-colored product. This reaction is equally influenced by the presence of AA, which, owing to its antioxidant properties, impedes the development of the color signal. This colorimetric approach exhibits high sensitivity, boasting low limits of detection (LOD) and quantification (LOQ) of 0.0252 and 0.0839 mM for H2O2, and 1.7724 and 5.7109 mg/L for AA, respectively. The method offers a broad linear range spanning from 0.029 to 26.47 mM for H2O2 and 0–40 mg/L for AA with a straightforward, cost-effective analytical procedure, and yields highly reliable results. The proposed method displays superior selectivity in detecting AA and high anti-interference capabilities. These findings underscore the photocatalytic and peroxidation-like activities of Au/Ag2MoO4 nanocomposite, positioning it as a promising candidate for various biomedical applications.

Flexible Graphene Paper Modified Using Pt&Pd Alloy Nanoparticles Decorated Nanoporous Gold Support for the Electrochemical Sensing of Small Molecular Biomarkers.

The exploration into nanomaterial-based nonenzymatic biosensors with superb performance in terms of good sensitivity and anti-interference ability in disease marker monitoring has always attained undoubted priority in sensing systems. In this work, we report the design and synthesis of a highly active nanocatalyst, i.e., palladium and platinum nanoparticles (Pt&Pd-NPs) decorated ultrathin nanoporous gold (NPG) film, which is modified on a homemade graphene paper (GP) to develop a high-performance freestanding and flexible nanohybrid electrode. Owing to the structural characteristics the robust GP electrode substrate, and high electrochemically catalytic activities and durability of the permeable NPG support and ultrafine and high-density Pt&Pd-NPs on it, the resultant Pt&Pd-NPs-NPG/GP electrode exhibits excellent sensing performance of low detection limitation, high sensitivity and anti-interference capability, good reproducibility and long-term stability for the detection of small molecular biomarkers hydrogen peroxide (H2O2) and glucose (Glu), and has been applied to the monitoring of H2O2 in different types of live cells and Glu in body fluids such as urine and fingertip blood, which is of great significance for the clinical diagnosis and prognosis in point-of-care testing.

A nanozyme with switchable enzyme-like activity for the logic gates detection of thymol and hydrogen peroxide in honey

A new nanozyme (CuGaa) with switchable enzyme-like activity of peroxidase and polyphenol oxidase was successfully prepared based on guanidinoacetic acid and copper. The two enzyme-like activities can be easily switched by changing temperature or adding MnCl2. At 4 °C, polyphenol oxidase-like activity decreased to nearly 1%, and the material is mainly characterized by peroxidase-like activity at this point. However, at 60 °C in the presence of 20 mM MnCl2, the peroxidase-like activity decreased to nearly 10%, and the polyphenol oxidase-like activity of the materials increased to 140%. Based on the switchable enzyme-like activity of CuGaa, detection methods for thymol and hydrogen peroxide were developed. In addition, a rapid combination strategy was further established combined with logic gate technology for the facile identification of complex contamination in honey, which provided new ideas for low-cost and rapid honey identification.