Hydrogen Evolution Techniques Research Articles

An investigation of the corrosion mechanisms of WE43 Mg alloy in a modified simulated body fluid solution: The influence of immersion time

The corrosion mechanisms and kinetics of WE43Mg alloy in a modified simulated body fluid (m-SBF) are investigated by electrochemical, hydrogen evolution and analytical techniques. The changes in the impedance response over time are related to four corrosion stages involving the formation of a partially protective corrosion layer and adsorption of Mg intermediates, formation of an inner passive MgO layer with increasing coverage over time, rupture of the corrosion layer and lateral growth of stable pits. ATR-FTIR, XRD and XPS results show the presence of an amorphous carbonated apatite/Mg(OH)2 mixed corrosion layer.

Corrosion Inhibition Effects and Adsorption Characteristics of Ethanol Extract of King Bitters Root (Andrographis paniculata) on Mild Steel in Hydrochloric and Tetraoxosulphate (VI) Acid Media

The corrosion inhibition performance of ethanol extract of Andrographis paniculata (King Bitter) root (EEAPR) on the corrosion of Mild Steel (MS) in 1.0 M HCl and H2SO4 acid solutions at 303K and elevated temperatures of 313, 323 and 333K was investigated and compared. The experimental work was performed by the use of weight loss and hydrogen evolution techniques. The results indicate that the extract inhibit the corrosion of mild steel in both acid media. However, the EEAPR exhibits higher maximum inhibition efficiency of 98.9 % in HCl than in H2SO4 (95.0 %) at 5.0 g/L. Inhibition efficiency was found to increase with increasing concentration of extract in both acid media but decreased with rise in temperature. Inhibition mechanism was deduced from the temperature dependence of the inhibition efficiency as well as from activation parameters that govern the process. Adsorption of extract on the MS sample in both acid media was found to obey the Langmuir adsorption isotherm. The phenomenon of physical adsorption is proposed from the obtained thermodynamic parameters.Â

Simultaneous impedance and volumetric studies and additionally potentiodynamic polarization measurements of molasses as a carbon steel corrosion inhibitor in 1M hydrochloric acid solution

The inhibition effect of molasses on the corrosion of low carbon steel in 1M hydrochloric acid solution was investigated by volumetric and electrochemical measurements. Potentiodynamic polarization and dynamic electrochemical impedance spectroscopy (DEIS) results were obtained and compared with to those, obtained with the hydrogen evolution technique. All results indicate that molasses functioned as a good inhibitor in 1M hydrochloric solution and inhibition efficiency increased with molasses concentration. The advantage of DEIS as a tool for investigation of molasses influence was discussed.

Improving in vitro corrosion resistance of biomimetic calcium phosphate coatings for Mg substrates using calcium hydroxide layer

Biomimetic calcium phosphate coatings have been studied to improve the corrosion resistance of biodegradable magnesium alloys. The corrosion resistance of these coatings is often limited by defects during creation. A method for improving the corrosion response of these coatings is therefore needed if biomimetic coatings are to be used for corrosion protection. In this study, a calcium hydroxide underlayer was applied to improve the properties of these biomimetic coatings. The in vitro corrosion response was studied using hydrogen evolution and electrochemical techniques. It was found that the calcium hydroxide layer increased the corrosion resistance of the coatings. The coatings created had fewer defects than the unmodified biomimetic coatings. Over time, the calcium hydroxide layer also prevented the defects in the coating from growing, leading to longer lasting protection. The results of this study suggest that calcium hydroxide coatings can significantly improve the corrosion protection of a biomimetic coating.

Coconut coir dust extract: a novel eco-friendly corrosion inhibitor for Al in HCl solutions

Corrosion inhibition of aluminium in 1 M HCl by coconut coir dust extract (CCDE) was studied using weight loss and hydrogen evolution techniques at 30 and 60°C. It was found that the studied extract exhibits a very good performance as inhibitor for aluminium corrosion in 1 M HCl. Results show that the inhibition efficiency increases with increasing temperature and concentration of the extract. Inhibitive effect was afforded by adsorption of the extracts' components which was found to accord with Langmuir adsorption isotherm. Inhibition mechanism is deduced from the temperature dependence of the inhibition efficiency and was further corroborated by the values of activation parameters obtained from the experimental data.

Corrosion inhibition and adsorption properties of ethanol extract ofHeinsia crinataon mild steel in H2SO4

Purpose – The purpose of this paper is to study the inhibitive and adsorptive characteristics of ethanol extract of Heinsia crinata for the corrosion of mild steel in H2SO4 solutions.Design/methodology/approach – The inhibition efficiencies were evaluated using weight loss, thermometric and hydrogen evolution techniques while adsorption properties were studied using IR spectroscopy.Findings – The inhibition efficiency of ethanol extract of Heinsia crinata varies with concentration of the extract, period of immersion and with temperature. The extract acts as an adsorption inhibitor because of its phytochemical composition. The extract is adsorbed spontaneously on the surface of mild steel according to Temkin and Frumkin adsorption isotherms. The mechanism of physical adsorption is proposed from the trend of the inhibition efficiency with temperature and the values of some kinetic and thermodynamic parameters obtained.Research limitations/implications – The paper provides information on the use of ethanol e...

Synergistic inhibition effect of polyethylene glycol–polyvinyl pyrrolidone blends for mild steel corrosion in sulphuric acid medium

AbstractThe corrosion inhibition of mild steel in sulphuric acid solution in the presence of polyethylene glycol (PEG), polyvinyl pyrrolidone (PVP), and their blends was investigated using weight loss and hydrogen evolution techniques at temperature range of 30–60°C. It was found that inhibition efficiency (η%) increases with increase in concentration of the homopolymers and decreases with increase in temperature. Inhibition efficiency was found to be synergistically enhanced on blending the two polymers with highest inhibition efficiency obtained for (PEG : PVP) blending ratio of 1 : 3. The experimental data obtained fitted well into Temkin adsorption isotherm model. Physical adsorption mechanism is proposed from the trend of inhibition efficiency with temperature. The proposed mechanism is also corroborated by kinetic and thermodynamic parameters obtained. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011

Inhibition effect of newly synthesized heterocyclic organic molecules on corrosion of steel in alkaline medium containing chloride

Two new organic compounds were tested experimentally as inhibitors for mild steel in NaOH in presence of NaCl by electrochemical and hydrogen evolution techniques. Results demonstrated that the two inhibitors show an adsorption on steel surface according to Langmuir adsorption isotherm. The inhibition efficiency increases with increasing inhibitor concentrations to attain a maximum value at 1.0 mM for compound I and at 6.0 mM for compound II, respectively. The results were confirmed by surface examination via scanning electron microscope.

Synergistic and antagonistic effects between halide ions and carboxymethyl cellulose for the corrosion inhibition of mild steel in sulphuric acid solution

The corrosion and corrosion inhibition effect of carboxymethyl cellulose (CMC) for mild steel in sulphuric acid medium was investigated using chemical (weight loss and hydrogen evolution) techniques at 30–60 °C. The effect of addition of halide ions (Cl−, Br−, and I−) was also studied. It was found that CMC functions as an inhibitor for acid induced corrosion for mild steel. Inhibition efficiency increases with increase in immersion time but decreases with increase in temperature. Addition of halide ions reveals that chloride ions (Cl−) antagonize the inhibition process whereas iodide ions (I−) exert synergistic effect on the corrosion inhibition by CMC. Corrosion inhibitive effect was afforded by adsorption of CMC molecules onto the mild steel surface both in the absence and presence of halide ions which was found to follow Langmuir adsorption isotherm model. The phenomenon of physical adsorption is proposed from decrease in inhibition efficiency with increase in temperature. The inhibition mechanism was further corroborated by the values of thermodynamic and kinetic parameters obtained from the experimental data.

Raphia hookeri gum as a potential eco-friendly inhibitor for mild steel in sulfuric acid

Exudate gum from Raphia hookeri (RH) was tested as corrosion inhibitor for mild steel in H2SO4 using weight loss and hydrogen evolution techniques at 30–60 °C. Results obtained revealed that RH act as corrosion inhibitor for mild steel in sulfuric acid medium. The corrosion rates in all concentrations studied increased with rise in temperature. The inhibition efficiency was observed to increase with increase in RH concentration but decreased with rise in temperature, which is suggestive of physical adsorption mechanism. The inhibitive action of RH is discussed in view of the adsorption of its phytochemical components onto steel surface, which protects the metal surface and thus do not permit the corrosion process to take place. The adsorption of the exudate gum onto the steel surface was found to follow the Langmuir adsorption isotherm. The free energies for the adsorption process and the apparent activation energies, enthalpies and entropies of the dissolution process were determined. The fundamental thermodynamic functions were used to glean important information about the RH inhibitory behavior. The results were explained in terms of chemical thermodynamics.

Synergistic Influence of Gum Arabic and Iodide Ion on the Corrosion Inhibition of Aluminium in Alkaline Medium

The effect of iodide ion on the corrosion inhibition of aluminium in NaOH in the presence of Gum Arabic (GA) was studied using weight loss and hydrogen evolution techniques at 303 and 313 K. The results obtained showed that inhibition efficiency increased with increasing GA concentration. The inhibiting action of GA was considerably enhanced by the addition of KI. The adsorption of KI, GA alone and in combination with iodide ion was found to obey Temkin adsorption isotherm. The inhibiting effect of GA and (GA+KI) increased with increase in temperature of the corrosion medium, indicating chemical adsorption mechanism. Synergism parameter evaluated was found to be greater than unity for the different concentrations of GA, which shows that the enhanced inhibition of GA caused by the addition of iodide ion is due to synergistic effect. It could be deduced from the thermodynamic parameters obtained that adsorption of GA alone and in combination with KI onto the metal surface is spontaneous.

Corrosion Inhibition of Mild Steel in Hydrochloric Acid by 2‐Benzoylpyridine and Pyridoxolhydrochloride

The inhibition of corrosion of mild steel in hydrochloric acid solutions by 2‐benzoylpyridine (2BP) and pyridoxolhydrochloride (PXO) at 303K, 313K and 323K has been investigated using weight loss and hydrogen evolution techniques. 2BP exhibited higher maximum inhibition efficiency (78.99%) than PXO (71.93%). Generally inhibition was found to increase with increasing inhibitor concentration and decreasing temperature. A first order type of mechanism has been deduced from the kinetic treatment of the results and the process of inhibition was attributed to physisorption. The difference in the inhibition behaviour of the two compounds has been explained on the basis of structure dependent electron donor properties of the inhibitors

INHIBITORY EFFECT AND ADSORPTION CHARACTERISTICS OF 2,3-DIAMINONAPHTHALENE AT ALUMINUM/HYDROCHLORIC ACID INTERFACE: EXPERIMENTAL AND THEORETICAL STUDY

The inhibitive effect of 2,3-diaminonaphthalene (2,3-DAN) for corrosion of aluminum in 1 M HCl was investigated using hydrogen evolution technique at 30 and 40°C. Quantum chemical calculation results showed that 2,3-DAN molecule possessed planar structure with a number of active centers, which aided the adsorption process. The Mulliken charge density, the highest occupied molecular orbital (HOMO), and the lowest unoccupied molecular orbital (LUMO) were found mainly focused around nitrogen atoms and the cyclic of the benzene as well. The presence of 2,3-DAN molecules in the corrosive medium (1 M HCl solution) inhibits the corrosion process of aluminum and as the concentration of 2,3-DAN increases the inhibition efficiency also increases but decreases with rise in temperature. The corrosion inhibition of 2,3-DAN was discussed in terms of blocking of the Al surface by adsorption of the molecules of the inhibitor at the active centers. It was found that the adsorption of 2,3-DAN onto the Al surface followed the Langmuir adsorption isotherm and 2,3-DAN adsorbed on Al surface probably by physisorption. The proposed physisorption mechanism was supported by the calculated values of Ea, Q ads , and ΔG ads .

Corrosion inhibition efficiency of nonionic Schiff base amphiphiles of p-aminobenzoic acid for aluminum in 4N HCL

A novel series of self-assembled nonionic Schiff base amphiphiles was synthesized and their chemical structures were confirmed using elemental analysis, FTIR spectroscopy and 1H NMR spectra. The surface activities of these amphiphiles were determined based on the data of surface and interfacial tension, critical micelle concentration, effectiveness, efficiency, maximum surface excess and minimum surface area. Thermodynamics of adsorption and micellization processes of these amphiphiles in their solutions were also calculated. The surface and thermodynamic data showed their higher tendency towards adsorption at the interfaces. The synthesized amphiphiles were evaluated as corrosion inhibitors for aluminum (3SR) at different doses (400–10ppm) in acidic medium (4N HCl) using weight loss and hydrogen evolution techniques. The corrosion measurements showed that the synthesized nonionic Schiff bases could serve as effective corrosion inhibitors. The surface and corrosion inhibition activities were correlated to the chemical structures of the inhibitors.

A study on the inhibition of mild steel corrosion in hydrochloric acid by pyridoxol hydrochloride

The inhibition of the corrosion of mild steel in 2M hydrochloric acid solutionsby Pyridoxol hydrochloride (PXO) has been studied using weight loss and hydrogenevolution techniques. The inhibitor (PXO) exhibited highest inhibition efficiency of71.93% at the highest inhibitor concentration of 1.0 x 10 -2 M investigated and atemperature of 303K from weight loss result. Also, inhibition was found to increase withincreasing concentration of the inhibitor and decreasing temperature. A first order typeof mechanism has been deduced from the kinetic treatment of the weight loss results andthe process of inhibition attributed to physical adsorption. The results obtained from thetwo techniques show that pyridoxol hydrochloride could serve as an effective inhibitorof the corrosion of mild steel in HCl acid solution. The compound obeys the Langmuiradsorption isotherm equation.

Eco‐friendly corrosion inhibitors: inhibitive action of ethanol extracts of Garcinia kola for the corrosion of mild steel in H2SO4 solutions

PurposeThis paper aims to investigate the inhibitive effect of ethanol extracts of Garcinia kola (EXG) for the corrosion of mild steel in H2SO4 solutions. The study is another trial to find a cheap and environmentally safe inhibitor for mild steel corrosion.Design/methodology/approachThe inhibition efficiency has been evaluated using the hydrogen evolution technique at 30‐60°C. The mechanism of adsorption inhibition and type of adsorption isotherm were proposed based on the trend of inhibition efficiency and kinetic data.FindingsThe results obtained indicate that EXG inhibits the corrosion of mild steel in acidic medium and that the inhibition efficiency increases with an increase in the concentration of ethanol extracts and decreasing temperature. The inhibition efficiency increased on addition of potassium iodide to EXG, indicating synergism. The experimental data obeyed the Langmuir adsorption isotherm as well as the El‐Awady et al. thermodynamic‐kinetic model. The activation energy of inhibition of 6.8508 KJ/mol calculated for the corrosion process suggests that the EXG molecules are physically adsorbed on the metal surface.Research limitations/implicationsFurther investigations involving electrochemical studies such as polarization method will provide further enlightenment on the mechanistic aspect of the corrosion inhibition.Originality/valueThis paper provides new information on the possible application of EXG as an environmentally friendly corrosion inhibitor under the specified conditions. This environmentally friendly inhibitor could find possible applications in metal surface anodizing and surface coatings.

Eco‐friendly corrosion inhibitors: the inhibitive action of Delonix Regia extract for the corrosion of aluminium in acidic media

PurposeTo investigate the inhibitive effect of Delonix regia extracts to reduce the corrosion rate of aluminium in acidic media. The study was a trial to find a low cost and environmentally safe inhibitor to reduce the corrosion rate of aluminium.Design/methodology/approachThe inhibition efficiency was evaluated using the hydrogen evolution technique at 30°C. The mechanism of adsorption inhibition and type of adsorption isotherm was characterised from trends of inhibition efficiency and kinetic data.FindingsDelonix regia extracts inhibited the corrosion of aluminium in hydrochloric acid solutions. The inhibition efficiency increased with increasing concentration of the inhibitor but decreased with increase in exposure time. The acid extracts (hydrochloric acid seeds extract (HSE) and hydrochloric acid leaf extract (HLE)) were found to be more effective than the ethanolic extracts (ethanol seeds extract (ASE) and ethanol leaves extract (ALE)) and the inhibition followed the order: HSE (93.6 per cent) > HLE (83.5 per cent) > ASE (63.9 per cent) > ALE (60.4 per cent). The low negative values of ΔGad: −20.14 kJ mol−1 for HSE, −18.08 kJ mol−1 for HLE, −15.96 kJ mol−1 for ASE and −15.12 kJ mol−1 for ALE, as calculated from the Langmuir isotherm, indicated that the inhibitor molecules adsorbed onto aluminium by a physiosorption‐based mechanism. A first‐order type of reaction mechanism was obtained from the kinetic treatment of the H2 gas evolution data.Research limitations/implicationsFurther investigations involving electrochemical studies such as polarization method should shed further light on the mechanistic aspects of the corrosion inhibition.Originality/valueThis paper provides new information on the possible application of Delonix regia as an environmentally friendly corrosion inhibitor under the specified conditions. This environmentally friendly inhibitor could find possible applications in metal surface anodizing and surface coatings.

A study on the inhibition of mild steel corrosion in hydrochloric acid by pyridoxol hydrochloride

The inhibition of the corrosion of mild steel in 2M hydrochloric acid solutions by Pyridoxol hydrochloride (PXO) has been studied using weight loss and hydrogen evolution techniques. The inhibitor (PXO) exhibited highest inhibition efficiency of 71.93% at the highest inhibitor concentration of 1.0 x 10 -2 M investigated and a temperature of 303K from weight loss result. Also, inhibition was found to increase with increasing concentration of the inhibitor and decreasing temperature. A first order type of mechanism has been deduced from the kinetic treatment of the weight loss results and the process of inhibition attributed to physical adsorption. The results obtained from the two techniques show that pyridoxol hydrochloride could serve as an effective inhibitor of the corrosion of mild steel in HCl acid solution. The compound obeys the Langmuir adsorption isotherm equation.

Water‐soluble polymers as corrosion inhibitors

PurposeTo determine the inhibition efficiency and adsorption characteristics of two water soluble polymers namely polyvinyl alcohol (PVA) and polyethyleneglycol (PGE) as corrosion inhibitors of mild steel in H2SO4.Design/methodology/approachThe inhibition efficiencies of PVA and PEG were evaluated using the weight loss and hydrogen evolution techniques at 30‐60°C.FindingsThe inhibition efficiency (I per cent) of the inhibitors increased with increase in concentration and temperature. The inhibitors (PVA and PEG) were found to obey Temkin, Freundlich and Langmuir adsorption isotherms from the fit of the experimental data at all concentrations and temperatures studied. The phenomenon of chemical adsorption is proposed from the activation parameters obtained. PEG was found to be a better inhibitor than PVA.Research limitations/implicationsThe mechanistic aspect of the corrosion inhibition can be better understood using electrochemical studies such as polarization and AC impedance spectra.Practical implicationsThe findings may be useful in cooling water systems in industries under simulated conditions.Originality/valueThis paper provides additional new information on the inhibiting characteristics of PVA and PEG as promising corrosion inhibitors.

Effect of halide ions on the corrosion inhibition of mild steel in acidic medium using polyvinyl alcohol

PurposeTo investigate the effect of halide ions on the corrosion inhibition of mild steel using polyvinyl alcohol (PVA) in H2SO4 at 30‐60°C and to study the mechanism of action.Design/methodology/approachThe corrosion rates were determined using the gravimetric (weight loss) and gasometric (hydrogen evolution) techniques. The results obtained in the absence and presence of PVA, halides, PVA – halides combination were used to calculate the inhibition efficiency (%I), degree of surface coverage and to propose the mechanism of inhibition and type of adsorption.FindingsResults obtained showed that inhibition efficiency (%I) increased with the increase in concentration of PVA, on the addition of halides and with the increase in temperature. Phenomenon of chemical adsorption was proposed and PVA was found to obey Langmuir, Flory‐Huggins and Freundlich adsorption isotherms. The synergism parameter, S1, evaluated was found to be greater than unity and the values of Ea, ΔH°, ΔS° and ΔG° obtained revealed that the adsorption process was spontaneous.Research limitations/implicationsElectrochemical studies such as polarization and AC impedance spectra will enlighten more on the mechanistic aspects of the corrosion inhibition and more polymers need to be evaluated as corrosion inhibitors.Practical implicationsPVA can be used as corrosion inhibitor and the addition of halides to PVA improves the inhibition efficiency considerably.Originality/valueThis paper provides new information on the effects of halides on the corrosion inhibition using PVA as an inhibitor for mild steel in acidic medium. Such a study had not been reported elsewhere.