Hybrid Fiber Research Articles

Feasibility of Sprayable Engineered Cementitious Composites Using Natural Sand and Low Fiber Content: Effect of Hybrid Fiber System, Silica Fume, and Air-Entraining and Shrinkage-Reducing Admixtures

Deterioration of corrugated steel culverts (CSCs) is a significant problem for the Virginia Department of Transportation and other U.S. transportation agencies. Spray-on lining using shotcrete engineered cementitious composites (ECCs) is a promising structural repair strategy for deteriorated CSCs. This study evaluates the feasibility of practical sprayable ECCs using natural silica sand and low fiber content, while forgoing the use of commonly utilized calcium sulfoaluminate cement to allow for delivery of the materials via ready-mixed concrete trucks. Aspects of the compositional space evaluated include the effect of a hybrid polyvinyl alcohol/polyethylene fiber system, silica fume (SF), shrinkage reducing admixture (SRA), and air-entraining admixture (AEA) on the properties of the composites. Experimental results suggested that the development of the proposed materials is feasible, because flow characteristics associated with shotcrete ECCs and ECC-like tensile ductility were achieved in the fresh and hardened state, respectively. Notwithstanding, further mixture optimization may be required for satisfactory field performance, which should be assessed through field testing. Generally, the use of the hybrid fiber system tended to improve the strength and ductility of the composites, especially when coupled with the use of SF. Furthermore, SF was effective at mitigating the strength loss associated with the incorporation of AEA and SRA, and meaningfully improved surface resistivity. SF also tended to reduce the mixture’s flow, whereas the contrary occurred with the use of SRA and AEA. SRA contributed to the reduction in drying shrinkage at early ages. However, the effect of SRA in reducing shrinkage was negligible at later ages.

Decellularized, Heparinized Small-Caliber Tissue-Engineered "Biological Tubes" for Allograft Vascular Grafts.

There remains a lack of small-caliber tissue-engineered blood vessels (TEBVs) with wide clinical use. Biotubes were developed by electrospinning and in-body tissue architecture (iBTA) technology to prepare small-caliber TEBVs with promising applications. Different ratios of hybrid fibers of poly(l-lactic-co-ε-caprolactone) (PLCL) and polyurethane (PU) were obtained by electrospinning, and the electrospun tubes were then implanted subcutaneously in the abdominal area of a rabbit (as an in vivo bioreactor). The biotubes were harvested after 4 weeks. They were then decellularized and cross-linked with heparin. PLCL/PU electrospun vascular tubes, decellularized biotubes (D-biotubes), and heparinized combined decellularized biotubes (H + D-biotubes) underwent carotid artery allograft transplantation in a rabbit model. Vascular ultrasound follow-up and histological observation revealed that the biotubes developed based on electrospinning and iBTA technology, after decellularization and heparinization cross-linking, showed a better patency rate, adequate mechanical properties, and remodeling ability in the rabbit model. IBTA technology caused a higher patency, and the heparinization cross-linking process gave the biotubes stronger mechanical properties.

Correlative Investigation on Dielectric-Mechanical-Morphological Characteristic for Kenaf-Glass-Hybrid Fibers Reinforced Epoxy Composite

In recent years, there are many applications where synthetic fibers and natural fibers are used as reinforcing materials in composites, such as the automotive and aerospace industries, the medical industry, and the construction industry. While these hybrid fibers effectively enhance mechanical and electrical properties, research into electrical characteristics remains inadequate and is an ongoing endeavor. In this work, synthetic woven glass fibers and natural woven kenaf fibers were used to fabricate composite materials by vacuum infusion technique. The dielectric properties of three different substrates, glass fibers, kenaf fibers and glass/kenaf fibers reinforced epoxy composites were investigated at 0° orientation. The ENA Network Analyzer was used to measure dielectric properties in a wide microwave frequency range. The substrates were single-joint overlapped with an adhesive and then mechanically tested. The shear strength of the joint as a function of strain, was tested using a Shimadzu universal testing machine. Visual inspections were performed to determine the failure modes of the composites. The dielectric constant and loss factor of the glass fiber composite were the highest, while the kenaf fiber composite had the lowest value. When a small amount of glass fibers is incorporated into kenaf fibers, which is called a hybrid composite, the polarization increases and the mechanical strength also increases compared to the kenaf fiber composite. Scanning electron microscopy (SEM) of the fractured tensile tests was performed to understand the nature of the interfaces between glass, kenaf and matrix. The kenaf/matrix interface was heterogeneous but exhibited voids, resulting in low dielectric properties and mechanical strength. By inserting a small amount of glass fibers, the hybrid with kenaf fibers improve the dielectric constant by 20.7% and the dielectric loss factor by 27% compared with the kenaf fiber composite. The results also show that the composites exhibit a correlation between the dielectric properties, tensile strength, and the morphological nature of the interfaces.

Experimental study of prestressed steel-HFRC composite girders under hogging moment

To alleviate cracks in the hogging region of continuous steel-concrete composite girders, the hybrid fiber reinforced concrete (HFRC) and prestressing technique were introduced to exploit a novel type of composite girders (prestressed steel-HFRC composite girders). Four specimens with different concrete slabs (normal concrete (NC) slab, prestressed NC slab, HFRC slab, prestressed HFRC slab) were tested under hogging moment to investigate their mechanical properties. The test results showed that the prestressed steel-HFRC composite girder could take advantage of the synergy of the prestressing technique and HFRC and, therefore, its ultimate capacity, cracking load and stiffness were the biggest while the crack width was the smallest among the specimens investigated. In addition, practical equations of ultimate/crack moment and crack width were obtained based on the test results. The proposed equations could provide the reference in the design of prestressed continuous steel-HFRC composite girders.

Mechanical and Microstructural Analysis of High-Performance Concrete Incorporated with Hybrid Fibres and Graphene Oxide

Mechanical and Microstructural Analysis of High-Performance Concrete Incorporated with Hybrid Fibres and Graphene Oxide

Flexural behaviour of geopolymer concrete beams with hybrid natural–synthetic fibre reinforcement

The requirement of excellent flexural stiffness in construction elements has initiated the use of fibre reinforcement. However, the processing complexity involved in the manufacture of synthetic fibres is environmentally hazardous. The use of natural fibres in geopolymer concrete (GPC) structures was investigated in this work using a hybridisation of natural and synthetic fibre. Natural basalt fibre (BF) was used with synthetic steel fibre (SF) in various proportions in GPC and tests were conducted to evaluate the workability, compressive strength, split tensile strength and flexural strength. It was found that, compared with the plain GPC, the addition of 1.5% BF and 0.5% SF resulted in 45%, 27% and 12% improvements in compressive, split tensile and flexural strengths, respectively. The compatibility between the SF and BF resulted in enhanced post-peak flexural behaviour, with 37% improvements in the modulus of elasticity and stiffness. As BF possesses more tensile strength than SF, the use of 1.5% BF and 0.5% SF provided better flexural and ductility properties than the use of SF alone, which could lead to the development of ductile GPC members under dynamic loading conditions.

Polyester Composite and Waste of Natural Materials Recyclable: Fracture Aspect After Tensile Test

Objective: This study aims to analyze the fractography of polymeric composites reinforced by recyclable materials, verifying the main types of defects present in the manufactured materials. Theoretical Framework: Composites can be understood as mutltiphasic materials that present a significant portion of the properties of their constintuintes. There are two phases, matrz and reinforcement. From the fractofrgographic analysis of the fracture surface of the material, one can evaluate the mechanisms of failure and interaction between the interfaces of the phases. Method: Specimens were manufactured using silicone molds according to ASTM D638. The matrix was unsaturated and pre-accelerated terephthalic polyester resin, while the reinforcement materials were: Jatoba wood residues, the hybridization of Jute and Sisal fibers, the hybrid of sisal and coffee grounds, and açaí leaves. Results and Discussion: For the composite with reinforcement of wood waste, there was a predominance of voids. For hybrids, the presence of the fibers culminated in the pull-out defect, therefore, using sisal fibers and coffee grounds, the presence of voids was also observed. The composite with acai leaves presented delamination between the reinforcement layers and the matrix. Research Implications: The analysis of the predominant defects, evaluates the possibility of improvement of the manufacturing process in order to certify the presence of this and promote and improve the efficiency of handling the material. Originality/Value: The use of natural and recyclable materials is of great importance from a sustainable analysis. In addition, it aims to generate added value to raw materials with little or no functionality.

Recent advances to engineer tough basalt fiber reinforced composites: A review

AbstractBasalt fibers, known as “green materials without pollution in the 21st century”, have gained widespread attention due to its good mechanical properties. Basalt fiber‐based composites have applications in various fields such as construction, transportation, energy, and protection. However, as an inorganic fiber material, basalt fiber is hard and brittle and prone to catastrophic failure, reducing the safety of the material. Therefore, it is important to strengthen the toughness of basalt fiber‐based composites. This paper reviews the contributions made by researchers in recent years to enhance the toughness of basalt fiber reinforced composites. It mainly focuses on four aspects: physical and chemical modification of fibers surface, mixed application of multiple fibers, different textile and 3D printing technology, and design of biomimetic structures. Through these methods, the toughness of basalt fiber‐reinforced composite materials was increased by 10%–90%. In today's advocacy for green industrial development, the research and application of basalt fibers are very important for advancing the process of green development. These contributions can promote the application of basalt fiber in engineering fields.Highlights Basalt fiber is a green material without pollution. Basalt fiber reinforced composites is the key material for engineering field. Strengthening interfacial adhesion can significantly improve the toughness of composites. Basalt fibers can serve as an alternative to glass fibers in composite materials. The hybridization of basalt fibers with soft fibers can effectively enhance the toughness of composites.

Tension Lap Splices in Recycled-Aggregate Concrete Strengthened with Steel–Polyolefin Fibers

The bond strength of tension lap splices in recycled-coarse-aggregate-reinforced concrete strengthened with hybrid (steel–polyolefin) fibers was experimentally investigated. This study was conducted with the help of twelve lap-spliced beam specimens. The replacement level of coarse natural aggregates with recycled concrete aggregate (RCA) was 100%. The following variables were investigated: various ranges of steel–polyolefin fibers—100–0%, 75–25%, 50–50%, 25–75%, and 0–100%—in which the total volume fraction of fibers (Vf) remains constant at 1%; and two lengths of lap splices for rebars of 16 mm diameter (db): 10 db and 15 db. The test results showed that the best range of steel–polyolefin fibers that gave the highest bond strength was 50–50%. The ductility of the fiber-reinforced recycled-aggregate (FR-RA) concrete was significantly improved for all the cases of various relative ratios of steel and polyolefin fibers. The bond strength was also predicted using three empirical equations proposed by Orangun et al., Darwin et al., and Harajli. This study showed that the Harajli equation gave a more accurate estimation of the bond strength of reinforcing bars embedded in FR-RA concrete than those proposed by Orangun et al. and Darwin et al.

Bond of steel bars in S-PVA-HF concrete with different cooling methods after high-temperature exposure

This experimental study compared the effect of natural cooling and water spray cooling on the bond properties of steel and steel-PVA hybrid fiber (S-PVA-HF) concrete after being exposed to high temperatures. Twenty-seven plain concrete specimens and fifty-four S-PVA-HF concrete specimens were designed for pullout tests using different cooling methods from high temperatures. This paper explored the bond strength and slip of steel bars and S-PVA-HF concrete with different temperatures and fiber admixtures after cooling from a high temperature. The differences and characteristics of the loss of bond properties of steel bars and S-PVA-HF concrete after natural cooling and water spray cooling were revealed. Phenomena during the heating process and changes in the apparent characteristics and mass burn-off rate after high-temperature exposure were analyzed The results showed that the bond strength and ductility of the specimens mixed with fibers were higher after high-temperature exposure compared with the normal concrete specimens. The bond strength of the specimens decreased upon increasing the temperature. Water spray cooling resulted in a greater loss in bond strength than natural cooling, but it improved the ultimate slip value of reinforced concrete. The ultimate slip value for normal concrete, P1S8 (mixed fiber concrete with 0.1 % PVA fiber + 0.8 % steel fiber), and P1S14 (mixed fiber concrete with 0.1 % PVA fiber + 0.8 % steel fiber) concrete specimens were improved by 8.54 %, 5.36 %, and 8.19 %, respectively.This shows that water spray cooling improved the ductility of concrete. The relationship between ultimate bond strength and ultimate slip value of steel bars and S-PVA-HF concrete after different cooling methods from high temperatures was developed.

Experimental investigations on mechanical performance, synergy assessment, and microstructure of pozzolanic and non‐pozzolanic hybrid steel fiber reinforced concrete

AbstractThis paper investigates the effects of pozzolanic substitutions for ordinary Portland cement (OPC) with silica fume (SF) and metakaolin (MK) on the mechanical and toughness performances of steel fiber reinforced concrete (SFRC). Initially, a reference concrete mix with a water‐to‐binder ratio of 0.4 is blended with different volume fractions of steel fibers with varying geometry: crimped steel (CS) and straight steel (SS), both individually and in combination, to examine their mechanical properties. In the subsequent phase, the study investigates the impact of combining macro‐ and microsteel fibers on flexural toughness, to determine potential synergy for suitable combinations. Also, the possible influence of pozzolans in the variation of flexural toughness of hybrid steel fiber reinforced concrete (Hy‐SFRC) was evaluated. Hybridization of steel fibers was found effective in improving the workability of the concrete mix up to 11%. SFRC mixes containing pozzolans exhibited a significant enhancement in compressive strength, modulus of rupture, and modulus of elasticity compared to non‐pozzolanic SFRC. The hybrid combination of CS 1.5% and SS 0.5% was considered the best in terms of mechanical properties. Additionally, the results of synergy assessment showed that hybridization of steel fibers in the pozzolanic concrete mix was particularly effective in the post‐cracking stages with a positive 14% compared to a negative 8% in the pre‐cracking stage. The pozzolanic addition improved the flexural toughness of Hy‐SFRC to about 10%–20%. Blending of SF and MK in Hy‐SFRC was found effective in enhancing the toughness mechanism of concrete compared to Hy‐SFRC mixes containing binary SF and MK, indicating a stronger bond between the fibers and the matrix resulting from the pore refinement and hydration products developed at the interface. Hy‐SFRC containing a ternary pozzolanic mix of SF 10% and MK 10% gave the best results in flexural toughness, and the corresponding synergy values were found to be the maximum. The results were consistent with the morphology analysis, which revealed an increase in hydration products at the interface between the aggregate and concrete matrix, as well as between the steel fiber and concrete matrix, due to the ternary blending of SF and MK.

Thermoplastic bicomponent‐fibers for organosheets via inline polymerization

AbstractState‐of‐the‐art organosheets suffer from several shortcomings that limit their applicability in high‐performance materials, mainly due to the imperfect combination of glass fibers and polymer. To overcome these issues, a novel hybrid fiber is presented, in which every single filament consists of a glass core and an individual, thin, thermoplastic polymer coating. Those fibers can immediately be consolidated into organosheets, without the necessity of the critical combination step. Production is realized by an ultra‐rapid inline coating of the filaments, incorporated into a standard spinning system. This solvent‐free process is realized by coating of the fibers with a tailor‐made, monomeric precursor solution, which is radiation‐polymerized immediately after application. Within fractions of a second, the coating layer is thus solidified, before coiling of the hybrid fiber. Due to the very low thickness of the coating and specific formulation of the precursor, tackless layers can be achieved before the coiling, even at industrial spinning speeds.Highlights Glass fibers are coated with a thermoplast via in situ polymerization. A precursor is developed which polymerizes in 100 ms. Glass fibers are coated completely with thermoplast by using a UV tunnel. Spinning velocities of about 600 m/min can be achieved. Hybrid fibers are consolidated into glass fiber‐reinforced plastics (GFRP).

Coconut fiber and fly ash polymer hybrid composite treated silane coupling agent: Study on morphology, physical, mechanical, and thermal properties

Composite materials made from natural ingredients are currently being developed by researchers as materials that are more environmentally friendly. Hybridization techniques used in making composite materials continue to progress, involving the combination of several raw materials with similar or different properties, such as organic/organic, organic/inorganic, and inorganic/inorganic. In this research, coconut fiber which is an organic material is combined with fly ash which is an inorganic material. The contrasting properties of these two raw materials prompted the evaluation of their combination by including a silane coupling agent, which facilitates the bonding of organic and inorganic components. The essence of this research is to test the effect of adding silane coupling material on several parameters, namely physical properties (density, water absorption, and thickness swelling), mechanical properties (tensile strength, tensile modulus, elongation, and flexural strength), and thermal properties. To prepare coconut fiber, alkaline treatment is used to remove hemicellulose and lignin. Then, the coconut fiber was soaked in a 5 % vinyltrimethoxysilane (TVS) solution by weight. The addition of silane coupling material affects the physical properties of the composite resulting in a decrease in water absorption by 33 % and a decrease in thickness swelling by 0.3 %. The inclusion of silane coupling agent led to an increase in tensile strength, tensile modulus, and flexural strength, while elongation decreased by 20 %. Thermal properties analysis showed that the silane treatment affected the decomposition of the composite material, reducing it by 2 % from 90 % without the coupling agent to 88 % with the coupling agent.

Damage and failure mechanisms of hybrid carbon fiber and steel fiber reinforced polymer composites

Fiber-reinforced plastics (FRPs) are widely used due to their superior properties but often suffer from brittle failure and poor structural integrity under impact loads. Metal fiber hybrids (MFH) offer a solution, but understanding their structure–property relationships remains challenging. This research provides a comprehensive mechanical characterization of a stainless steel-carbon fiber hybrid (SCFRP) embedded in epoxy resin, with a particular focus on the failure mechanisms and their influences. Therefore, the mechanical properties of the material, as well as the propagation and damage of the fracture, are investigated. In addition, three main failure mechanisms are identified and analyzed. The failure mode of a SCFRP laminate can be influenced by its composition, architecture, and specimen size and result from a combination of the blast effect of the brittle failing carbon fibers, the magnitude of the associated damage, and the movement of the fracture gap formation initiated by the carbon fiber failure.

Effect of hybridisation on the mechanical and weathering characteristics on jute-arecanut leaf-epoxy composites

ABSTRACT Natural fibres play a crucial role in composites by offering renewable, sustainable, low cost and lightweight alternatives to synthetic fibres, promoting eco-friendly composites. Combination of natural fibres such as jute and areca nut in fabricating hybrid composites with superior properties forms the basis of this study. It was observed that mechanical properties increased with increasing natural fibre content. However, jute composites exhibited better properties (strength and rigidity) than arecanut leaf fibre composites due to their inherent superior properties. Hybridisation of fibres yielded higher properties showing that the combination of jute and areca nut fibres (30 wt % fibre content) is more effective in reinforcing the composites. Weathering characteristics revealed that the water absorption and swelling occurred in composites upon their exposure to external environment, water and chemicals. Moreover, their impact properties also decreased subsequent to weathering. Finite element analysis was carried out on these composites under tensile and flexural loading conditions yielded similar trends with experimental results. Remarkable mechanical properties exhibited due to hybridisation of these composites give them potential to be used in different domains such as automobile interiors, furniture, packaging, etc., with lower cost due to the use of natural fibres.

Study on mechanical properties and meso-damage mechanism of carbon-polyvinyl alcohol hybrid fiber reinforced recycled coarse aggregate concrete under the coupling action of sodium sulfate and dry-wet cycles

In order to investigate the influence of the coupling effect of sodium sulfate dry-wet (DW) cycles on the mechanical properties of carbon-polyvinyl alcohol hybrid fiber reinforced recycled coarse aggregate concrete (HFRAC), HFRAC specimens were subjected to uniaxial compression tests. The total volume fraction of fibers was kept constant at 0.4%, and various volume fractions of carbon fibers (CF) were added to the recycled coarse aggregate concrete (RAC), namely 0%, 0.1%, 0.2%, 0.3%, and 0.4%, with polyvinyl alcohol (PVA) fibers replacing a portion of CF in equivalent volume. Uniaxial compressive stress–strain curves were obtained for HFRAC specimens subjected to different numbers of DW cycles (0, 30, 60, and 120 cycles). Microscopic testing methods including acoustic emission (AE), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and nuclear magnetic resonance (NMR) were employed to analyze the microstructure, erosion product composition, and pore structure changes of the specimens. The results revealed that, for RAC specimens, the peak stress (σp) and elastic modulus (E) initially increased and then decreased, whereas the peak strain (εp) initially decreased and then increased with an increase in the number of DW cycles. After adding hybrid fibers, the σp values of CF, Hybrid 3:1, Hybrid 1:1, Hybrid 1:3, and PVA specimens increased (or decreased) by 12.0%, 11.43%, 0.9%, −9.5%, and −8.5%, respectively, compared to RAC. The Hybrid 1:3 specimen exhibited a negative hybrid effect. With an increase in the erosion age, the Hybrid 3:1 specimen demonstrated enhanced resistance to sulfate attack and achieved the highest σp value after 120 cycles. The influence of sulfate DW cycles coupling on the microscopic damage mechanism of HFRAC was analyzed using a statistical damage constitutive model. The microscopic damage evolution process was characterized by five characteristic parameters: E0, εa, εh, εb, and H. The analysis results indicated a clear correlation between the variation of these characteristic parameters and the number of DW cycles. An effective connection was established between the microscopic damage mechanism and the macroscopic nonlinear constitutive behavior. The phenomenon of relative lagging of acoustic emission signals during the uniaxial compression process was explained from the perspective of effective stress. This study provides a theoretical basis for the promotion and application of RAC under sulfate DW cycle environments.

Exploring a New Class of PVDF/3‐Aminopropyltriethoxysilane (core) and 2,2‐Bis(hydroxymethyl)butyric Acid (monomer)‐Based Hyperbranched Polyester Hybrid Fibers by Electrospinning Technique for Enhancing Triboelectric Performance

AbstractWith the rapid advancement in sensor technologies, triboelectric nanogenerators (TENGs) have emerged as a promising sustainable power source for intelligent electronics. Herein, fabricated a novel 3‐aminopropyltriethoxysilane (core) and 2,2‐bis(hydroxymethyl)butyric acid (monomer)‐based hyperbranched polyester by facile single‐step polycondensation technique generation 2 (Si‐HBP‐G2). Further, a new class of polyvinylidene fluoride (PVDF) and different weight percentages (0, 5, 10, 15, and 20 wt%) of Si‐HBP‐G2 hybrid fiber blends are prepared by traditional electrospinning technique. The as‐prepared Si‐HBP‐G2 and its blends are well characterized using SEM/EDS, FTIR, NMR, and XRD studies. The influence of Si‐HBP‐G2 content on triboelectric performance in terms of the open circuit potential (VOC) and short circuit current (ISC) is evaluated using aluminum (Al) as a counter electrode. Among them, 15 wt% of Si‐HBP‐G2/PVDF hybrid fiber mat (PG2‐15) exhibits superior electrical performance. Which is almost increased 5.9 times (22–130 V) of VOC and 4.9 times (0.71–3.5 µA) of ISC than PVDF fiber mate. These results reveal the significance of Si‐HBP‐G2 in the triboelectric performance. The optimized TENG device (PG2‐15/Al‐TENG) exhibits a peak power density of 0.2 Wm−2 at 100 MΩ external load. Finally, the PG2‐15/Al‐TENG practically demonstrates real‐time application energy harvesting applications such as powering 100 LEDs and a stopwatch.

Experimental and finite element analysis of ballistic properties of composite armor made of alumina, carbon and UHMWPE

AbstractThe performance of multi‐layer ceramic/composite ballistic armor consisting of Alumina, Carbon fiber, and Ultra High Molecular Weight Polyethylene (UHMWPE) under the impact of 7.62 × 51 M61 caliber armor‐piercing (AP) bullets was examined by experimental and finite element methods. The alumina ceramic thickness used in the experiments is 12 mm. The composite structure thickness used in all samples is 10 mm. Explicit dynamic analyses were also conducted using the Ls‐Dyna to verify the experimental studies. The analysis results were compared with experimental studies and evaluated by considering the damage status of the bullet and armor. According to ballistic test results, partial penetration was observed in all armor produced. The front ceramic layer caused corrosion of the bullet, and a mushrooming effect occurred on it. The carbon fiber layer has dramatically helped as an alternative or support to UHMWPE. Since the results obtained with the carbon fiber ratios used remain within the standards, it will not pose a problem regarding usage. On the contrary, using carbon fiber, which is relatively easier to produce and supply than UHMWPE and more economically suitable, will provide more significant benefits. Experimental and numerical studies have revealed consistent results for all armors.Highlights The effect of a 7.62 × 51 armor‐piercing bullet on ceramic/composite armor was examined. Carbon fiber and UHMWPE hybrid structure was created in different thicknesses. The carbon fiber layer has dramatically helped as an alternative or support to UHMWPE. Using carbon fiber, which is relatively easier to produce and supply than UHMWPE and is more economically suitable. Experimental and numerical studies have revealed consistent results for all armors.

Lightweight, Elastic, and Superhydrophobic Multifunctional Organic-Inorganic Fibrous Aerogels for Efficient Oily Wastewater Purification and Electromagnetic Microwave Absorption.

Lightweight and robust aerogels with multifunctionality are highly desirable to meet the technological demands of current society. Herein, we designed lightweight, elastic, and superhydrophobic multifunctional organic-inorganic fibrous hybrid aerogels which were assembled with organic aramid nanofibers and inorganic hierarchical porous carbon fibers. Thanks to the organic-inorganic fiber hybridization strategy, the optimal aerogels possessed remarkable compressibility and elasticity. Benefiting from the microscopic hierarchical porous structure of carbon fibers and the macroscopic macroporous lamellar structure of aerogels, the optimal aerogels exhibited superb lightweight property, conspicuous electromagnetic microwave absorption ability, and outstanding oily wastewater purification capacity. As for electromagnetic microwave absorption, it achieved a strong reflection loss of -41.8 dB, and the effective absorption bandwidth reached 6.86 GHz. Besides, the oil adsorption capacity for trichloromethane reached as high as 93.167 g g-1 with a capacity retention of 95.6% after 5 cycles. Meanwhile, it could act as a gravity-driven separation membrane to continuously separate trichloromethane from a trichloromethane-water mixture with a high flux of 7867.37 L·m-2·h-1, even for surfactant-stabilized water-in-n-heptane emulsions of 3794.94 L·m-2·h-1. Such a strategy might shed some light on the construction of multifunctional aerogels toward broader applications.

Wet spun cellulose nanocrystal/MXene hybrid fiber regulated by bridging effect for high electrochemical performance supercapacitor

Wet spun cellulose nanocrystal/MXene hybrid fiber regulated by bridging effect for high electrochemical performance supercapacitor