Hub Leakage Flow Research Articles

Aerothermal Impact of the Interaction Between Hub Leakage and Mainstream Flows in Highly-Loaded High Pressure Turbine Blades

This paper describes experimental and numerical investigations of a highly-loaded rotor blade with leakage (purge) flow injection through an upstream overlapping seal. The effects of both leakage mass flow rates and swirl have been studied to examine their effects on the aerothermal performance. As the leakage mass flow rate was increased, the loss generally increased. The increase in the losses was found to be nonlinear with the three distinct regimes of leakage-mainstream interaction being identified. The varying sensitivity of the losses to the leakage fraction was linked to the effects of the upstream potential field of the blade on a vortical structure originating from the outer part of the seal. This vortical structure affected the interaction between the leakage and mainstream flows as it grew to become the hub passage vortex. Very limited cooling was provided by the leakage flows. The coolant was mainly concentrated close to the suction surface in the front part of the rotor platform and on the blade suction surface in the path of the passage vortex. However, the regions benefiting from cooling were also characterized by higher values of the heat transfer coefficient. As a consequence, the net heat flux reduction was small, and the leakage injection was thus deemed thermally neutral.

Unsteady Effects in Axial Compressors: A Multistage Simulation

This work presents a numerical simulation of a four-stage axial compressor with cantilevered stators and repeating stages. Two simulations have been accomplished, namely, unsteady with sliding plane and steady with mixing plane, over a wide range of operating conditions. The solver is an unsteady Reynolds-averaged Navier–Stokes code with the Spalart–Allmaras turbulent model. It has been found that the greatest effect of unsteadiness is near the end walls. The stall point for the unsteady simulation is 40% closer to the experimental data when compared with the steady one with mixing planes. This is due to the recovery and segregation of the rotor tip vortex near the casing, which has a stabilizing effect in terms of stall limit. The unsteady simulation is able to reproduce total pressure loss experimentally observed near the hub at the stator exit but not found in the steady simulation. A previous experimental campaign suggested this loss was generated by the wakes of upstream inlet guide vanes propagating through the machine. However, this work found that it is generated by the migration of hub leakage flow induced by the incoming rotor wakes. The unsteady simulation shows higher performance at midspan. This has been found to be related to the rotor wake rectification with a 70% inviscid recovery of wake.

The Effect of Coolant Injection on the Endwall Flow of a High Pressure Turbine

This paper presents a study of the effects of two types of hub coolant injection on the rotor of a high pressure gas turbine stage. The first involves the leakage flow from the hub cavity into the mainstream. The second involves a deliberate injection of coolant from a row of angled holes from the edge of the stator hub. The aim of this study is to improve the distribution of the injected coolant on the rotor hub wall. To achieve this, it is necessary to understand how the coolant and leakage flows interact with the rotor secondary flows. The first part of the paper shows that the hub leakage flow is entrained into the rotor hub secondary flow and the negative incidence of the leakage strengthens the secondary flow and increases its penetration depth. Three-dimensional unsteady calculations were found to agree with fast response pressure probe measurements at the rotor exit of a low speed test turbine. The second part of the paper shows that increasing the injected coolant swirl angle reduced the secondary flow penetration depth, improves the coolant distribution on the rotor hub, and improves stage efficiency. Most of the coolant however, was still found to be entrained into the rotor secondary flow.

Viscous-Flow Two-Dimensional Analysis Including Secondary Flow Effects

During the last few decades extremely powerful Quasi-three-dimensional (3D) codes and fully 3D Navier-Stokes solvers have been developed and successfully utilized in the design process and optimization of multistage axial-flow compressors. However, most of these methods proved to be difficult in handling and extremely time consuming. Due to these disadvantages, the primary stage design and stage matching as well as the off-design analysis is nowadays still based on fast 2D methods incorporating loss-, deviation- and end wall modeling. Only the detailed 3D optimization is normally performed by means of advanced 3D methods. In this paper a fast and efficient 2D calculation method is presented, which already in the initial design phase of multistage axial flow compressors, considers the influence of hub leakage flows, tip clearance effects, and other end wall flow phenomena. The method is generally based on the fundamental approach by Howard and Gallimore (1992). In order to allow a more accurate prediction of skewed and nondeveloped boundary layers in turbomachines, an improved theoretical approach was implemented. Particularly the splitting of the boundary layers into an axial and tangential component proved to be necessary in order to account for the change between rotating and stationary end walls. Additionally, a new approach is used for the prediction of the viscous end wall zones including hub leakage effects and strongly skewed boundary layers. As a result, empirical correlations for secondary flow effects are no longer required. The results of the improved method are compared with conventional 2D results including 3D loss- and deviation-models, with experimental data of a three-stage research compressor of the Institute for Jet Propulsion and Turbomachinery of the Technical University of Aachen and with 3D Navier-Stokes solutions of the V84.3A compressor and of a multistage Siemens research compressor. The results obtained using the new method show a remarkable improvement in comparison with conventional 2D methods. Due to the high quality and the extremely short computation time, the new method allows an overall viscous design of multistage compressors for heavy duty gas turbines and aeroengine applications.