Hospital Hot Water Research Articles

Validation of quantitative real-time polymerase chain reaction for detection of Legionella pneumophila in hospital water networks

Rapid monitoring of Legionella pneumophila (Lp) is essential to reduce the risk of Legionnaires' disease in healthcare facilities. However, culture results take at least eight days, delaying the implementation of corrective measures. Here, we assessed the performance of a qPCR method and determined qPCR action thresholds for the detection of Lp in hospital hot water networks (HWNs). Hot water samples (N= 459) were collected from a hospital HWN. Lp were quantified using iQ-Check® Quanti real-time PCR Quantification kits (Bio-Rad) and the results were compared with those of culture. qPCR thresholds corresponding to the culture action thresholds of 10 and 1000cfu/L were determined on a training dataset and validated on an independent dataset. Lp concentrations measured by culture and qPCR were correlated for both the training dataset (Spearman's correlation coefficient ρ= 0.687, P<0.0001) and the validation dataset (ρ= 0.661, P<0.0001). Lp qPCR positivity thresholds corresponding to culture action thresholds of 10cfu/L was 91 genome units (gu) per litre (sensitivity, 86.4%; negative predictive value - NPV, 93.3%) and that corresponding to culture action thresholds of 1000cfu/L was 1048 gu/L (sensitivity, 100%; NPV, 100%). Detection of Lp by qPCR could be implemented with confidence in hospitals as a complement to culture in the monitoring strategy to speed up the implementation of corrective measures.

Persistent contamination of a hospital hot water network by Legionella pneumophila

We assessed the contamination with Legionella pneumophila (Lp) of the hot water network (HWN) of a hospital, mapped the risk of contamination, and evaluated the relatedness of isolates. We further validated phenotypically the biological features that could account for the contamination of the network. We collected 360 water samples from October 2017 to September 2018 in 36 sampling points of a HWN of a building from a hospital in France. Lp were quantified and identified with culture-based methods and serotyping. Lp concentrations were correlated with water temperature, date and location of isolation. Lp isolates were genotyped by pulsed-field gel electrophoresis and compared to a collection of isolates retrieved in the same HWN two years later, or in other HWN from the same hospital. 207/360 (57.5%) samples were positive with Lp. In the hot water production system, Lp concentration was negatively associated with water temperature. In the distribution system, the risk of recovering Lp decreased when temperature was >55°C (p<10-3), the proportion of samples with Lp increased with distance from the production network (p<10-3), and the risk of finding high loads of Lp increased 7.96 times in summer (p=0.001). All Lp isolates (n=135) were of serotype 3, and 134 (99.3%) shared the same pulsotype which is found two years later (Lp G). In vitro competition experiments showed that a 3-day culture of Lp G on agar inhibited the growth of a different pulsotype of Lp (Lp O) contaminating another HWN of the same hospital (p=0.050). We also found that only Lp G survived to a 24h-incubation in water at 55°C (p=0.014). We report here a persistent contamination with Lp of a hospital HWN. Lp concentrations were correlated with water temperature, season, and distance from the production system. Such persistent contamination could be due to biotic parameters such as intra-Legionella inhibition and tolerance to high temperature, but also to the non-optimal configuration of the HWN that prevented the maintenance of high temperature and optimal water circulation.

Computational framework for evaluating risk trade-offs in costs associated with legionnaires' disease risk, energy, and scalding risk for hospital hot water systems

We present a computational framework to evaluate trade-offs in energy, scalding, and Legionnaires' disease illness risk costs. This framework is a foundation for a decision support tool for building operation.

Local Adaptation of Legionella pneumophila within a Hospital Hot Water System Increases Tolerance to Copper.

In large-building water systems, Legionella pneumophila is exposed to common environmental stressors such as copper. The aim of this study was to evaluate the susceptibility to copper of L. pneumophila isolates recovered from various sites: two clinical and seven environmental isolates from hot water system biofilm and water and from cooling tower water. After a 1-week acclimation in simulated drinking water, strains were exposed to various copper concentrations (0.8 to 5 mg/liter) for over 672 h. Complete loss of culturability was observed for three isolates following copper exposure to 5 mg/liter for 672 h. Two sequence type 1427 (ST1427)-like isolates were highly sensitive to copper, while the other two, isolated from biofilm samples, maintained higher culturability. The expression of the copper resistance gene copA evaluated by reverse transcription-quantitative PCR (RT-qPCR) was significantly higher for the biofilm isolates. All four ST1427-like isolates were recovered from the same water system during an outbreak. Whole-genome sequencing results confirmed that the four isolates are very close phylogenetically, differing by only 29 single nucleotide polymorphisms, suggesting in situ adaptation to microenvironmental conditions, possibly due to epigenetic regulation. These results indicate that the immediate environment within a building water distribution system influences the tolerance of L. pneumophila to copper. Increased contact of L. pneumophila biofilm strains with copper piping or copper alloys in the heat exchanger might lead to local adaptation. The phenotypic differences observed between water and biofilm isolates from the hot water system of a health care facility warrants further investigation to assess the relevance of evaluating disinfection performances based on water sampling alone.IMPORTANCELegionella pneumophila is a pathogen indigenous to natural and large building water systems in the bulk and the biofilm phases. The immediate environment within a system can impact the tolerance of L. pneumophila to environmental stressors, including copper. In health care facilities, copper levels in water can vary, depending on water quality, plumbing materials, and age. This study evaluated the impact of the isolation site (water versus biofilm, hot water system versus cooling tower) within building water systems. Closely related strains isolated from a health care facility hot water system exhibited variable tolerance to copper stress, shown by differential expression of copA, with biofilm isolates displaying highest expression and tolerance. Relying on the detection of L. pneumophila in water samples following exposure to environmental stressors such as copper may underestimate the prevalence of L. pneumophila, leading to inappropriate risk management strategies and increasing the risk of exposure for vulnerable patients.

Safety and Effectiveness of Monochloramine Treatment for Disinfecting Hospital Water Networks.

The formation of potentially carcinogenic N-nitrosamines, associated with monochloramine, requires further research due to the growing interest in using this biocide for the secondary disinfection of water in public and private buildings. The aim of our study was to evaluate the possible formation of N-nitrosamines and other toxic disinfection by-products (DBPs) in hospital hot water networks treated with monochloramine. The effectiveness of this biocide in controlling Legionella spp. contamination was also verified. For this purpose, four different monochloramine-treated networks, in terms of the duration of treatment and method of biocide injection, were investigated. Untreated hot water, municipal cold water and, limited to N-nitrosamines analysis, hot water treated with chlorine dioxide were analyzed for comparison. Legionella spp. contamination was successfully controlled without any formation of N-nitrosamines. No nitrification or formation of the regulated DBPs, such as chlorites and trihalomethanes, occurred in monochloramine-treated water networks. However, a stable formulation of hypochlorite, its frequent replacement with a fresh product, and the routine monitoring of free ammonia are recommended to ensure a proper disinfection. Our study confirms that monochloramine may be proposed as an effective and safe strategy for the continuous disinfection of building plumbing systems, preventing vulnerable individuals from being exposed to legionellae and dangerous DBPs.

Characterisation of Microbial Community Associated with Different Disinfection Treatments in Hospital hot Water Networks.

Many disinfection treatments can be adopted for controlling opportunistic pathogens in hospital water networks in order to reduce infection risk for immunocompromised patients. Each method has limits and strengths and it could determine modifications on bacterial community. The aim of our investigation was to study under real-life conditions the microbial community associated with different chemical (monochloramine, hydrogen peroxide, chlorine dioxide) and non-chemical (hyperthermia) treatments, continuously applied since many years in four hot water networks of the same hospital. Municipal cold water, untreated secondary, and treated hot water were analysed for microbiome characterization by 16S amplicon sequencing. Cold waters had a common microbial profile at genera level. The hot water bacterial profiles differed according to treatment. Our results confirm the effectiveness of disinfection strategies in our hospital for controlling potential pathogens such as Legionella, as the investigated genera containing opportunistic pathogens were absent or had relative abundances ≤1%, except for non-tuberculous mycobacteria, Sphingomonas, Ochrobactrum and Brevundimonas. Monitoring the microbial complexity of healthcare water networks through 16S amplicon sequencing is an innovative and effective approach useful for Public Health purpose in order to verify possible modifications of microbiota associated with disinfection treatments.

Advances in Legionella Control by a New Formulation of Hydrogen Peroxide and Silver Salts in a Hospital Hot Water Network.

Legionella surveillance is an important issue in public health, linked to the severity of disease and the difficulty associated with eradicating this bacterium from the water environment. Different treatments are suggested to reduce Legionella risk, however long-term studies of their efficiency are lacking. This study focused on the activity of a new formulation of hydrogen peroxide and silver salts, WTP828, in the hospital hot water network (HWN) to contain Legionella contamination during two years of treatment. The effectiveness of WTP828 was tested measuring physical-chemical and microbiological parameters such as Legionella, Pseudomonas aeruginosa (P. aeruginosa), and a heterotopic plate count (HPC) at 36 °C. Legionella isolates were identified by serotyping and genotyping. WTP 828 induced a reduction in Legionella–positive sites (60% to 36%) and contamination levels (2.12 to 1.7 log10 CFU/L), with isolates belonging to L. pneumophila SG1 (ST1 and ST104), L. anisa and L. rubrilucens widely distributed in HWN. No relevant contamination was found for other parameters tested. The long-term effect of WTP828 on Legionella containment suggest the easy and safe application of this disinfectant, that combined with knowledge of building characteristics, an adequate environmental monitoring and risk assessment plan, become the key elements in preventing Legionella contamination and exposure.

Legionella pneumophila levels and sequence-type distribution in hospital hot water samples from faucets to connecting pipes

Recent studies have reported increased levels of Legionella pneumophila (Lp) at points of use compared to levels in primary and secondary components of hot water systems, suggesting possible selection by environmental conditions. In this study, concentrations of Lp in a hospital hot water system were evaluated by profile sampling, collecting successive water samples to determine the prevalence at the faucet (distal) and upstream piping before and after a system intervention to increase temperature. Lp strain diversity was compared between different points of use and different areas of the hot water system (i.e., tap, intermediate piping and main upflow piping). In total, 47 isolates were recovered from 32 positive hot water samples collected from designated taps, showers and recirculation loops; these isolates were subsequently analyzed by sequence-based typing (SBT). Lp levels were comparable between first draw (500 mL) and flushed (2 and 5 min) samples, whereas a decrease was observed in the amount of culturable cells (1 log). Two sequence types (STs) were identified throughout the system. ST378 (sg4/10) was present in 91% of samples, while ST154-like (sg1) was present in 41%; both STs were simultaneously recovered in 34% of samples. Isolated STs displayed comparable tolerance to copper (0.8–5 mg/L) and temperature (55 °C, 1 h) exposure. The ability to replicate within THP1 cells and Acanthamoeba castellanii was similar between the two STs and a comparative environmental outbreak strain. The low Lp diversity and the detection of both Lp sequence types in repeated subsequent samples collected from positive faucets in a hospital wing suggest a minimal impact of the distal conditions on strain selection for the sampled points, as well as a possible adaptation to stressors present in the system, leading to the predominance of a few strains.

Prevalence of Legionella spp. in hot water samples from Polish hospitals in 2009-2013

Background: Microbiological threat from Legionella spp. is associated with the current widespread use of air-condition systems and frequent colonization of hot water distribution systems in public facilities (hospitals, hotels, nursing homes). This poses a particularly high risk in hospitalized patients, as many of them are immunocompromised. More than 50 species and 72 serogroups of Legionella spp. have been described thus far, including more than 20 species being pathogenic to humans. Material/Methods: Microbiological threat posed by Legionella spp. was assessed based on a retrospective analysis of microbiological quality of water from hot water distribution systems in Polish hospitals, determined in 2009-2013 at certified laboratories of the Sanitary-Epidemiological Surveillance. The results were kindly provided by the hospitals’ administration upon request, for which the authors would like to express their deepest gratitude. The study material included samples of hot water from internal distribution systems in 379 Polish hospitals, collected by the State Sanitary Inspectorate. Results: Based on the results of microbiological analyses, we were able to estimate Legionella spp. colonization rates in hospital water distribution systems and to assess the activities undertaken by the State Sanitary Inspectorate to reduce excessive bacterial counts in this reservoir. Microbiological analyses conducted in 2009-2013, i.e. after implementing a statutory obligation to monitor Legionella spp. in hospital hot water distribution systems, showed elevated bacterial counts in 3.92% to 12.7% of the samples. These findings justify further microbiological monitoring of hospital water distribution systems. Discussion: The prevalence of the most pathogenic serotype SG1 in hot water distribution systems of Polish hospitals is relatively low compared to other European countries. To maintain this favorable status, hospital water systems should be monitored not only for the presence of Legionella pneumophila, but also for the prevalence of serogroup 1 L. pneumophila.

Rate of Legionella pneumophila colonization in hospital hot water network after time flow taps installation

In hospital water systems legionellae may be resistant to disinfectants in pipework, which is a problem particularly in areas where there is low flow or stagnation of water. We evaluated legionella colonization of a water network of an Italian hospital after time flow taps (TFTs) installation in proximity to dead legs. The water volume flushed was 64L/day from May 2016, and 192L/day from December 2016. Before TFTs installation, Legionella pneumophila sg2-14 was detected in all points (4×104±3.1×104cfu/L). All sites remained positive (2.9×104±1.9×104cfu/L) through November 2016. From December 2016 legionella persisted in one point only (2×102 to 6.8×103cfu/L). TFTs with chemical disinfection may reduce legionella colonization associated with dead legs.

Energy Conservation and the Promotion of Legionella pneumophila Growth: The Probable Role of Heat Exchangers in a Nosocomial Outbreak.

OBJECTIVE To determine the source of a Legionella pneumophila serogroup 5 nosocomial outbreak and the role of the heat exchanger installed on the hot water system within the previous year. SETTING A 400-bed tertiary care university hospital in Sherbrooke, Canada. METHODS Hot water samples were collected and cultured for L. pneumophila from 25 taps (baths and sinks) within wing A and 9 taps in wing B. Biofilm (5) and 2 L water samples (3) were collected within the heat exchangers for L. pneumophila culture and detection of protists. Sequence-based typing was performed on strain DNA extracts and pulsed-field gel electrophoresis patterns were analyzed. RESULTS Following 2 cases of hospital-acquired legionellosis, the hot water system investigation revealed a large proportion of L. pneumophila serogroup 5 positive taps (22/25 in wing A and 5/9 in wing B). High positivity was also detected in the heat exchanger of wing A in water samples (3/3) and swabs from the heat exchanger (4/5). The outbreak genotyping investigation identified the hot water system as the source of infections. Genotyping results revealed that all isolated environmental strains harbored the same related pulsed-field gel electrophoresis pattern and sequence-based type. CONCLUSIONS Two cases of hospital-acquired legionellosis occurred in the year following the installation of a heat exchanger to preheat hospital hot water. No cases were reported previously, although the same L. pneumophila strain was isolated from the hot water system in 1995. The heat exchanger promoted L. pneumophila growth and may have contributed to confirmed clinical cases. Infect. Control Hosp. Epidemiol. 2016;1475-1480.

Effect of monochloramine treatment on the microbial ecology of Legionella and associated bacterial populations in a hospital hot water system

Opportunistic pathogens, including Legionella spp. and non-tuberculous mycobacteria, can thrive in building hot water systems despite municipal and traditional on-site chlorine disinfection. Monochloramine is a relatively new approach to on-site disinfection, but the microbiological impact of on-site chloramine use has not been well studied. We hypothesized that comparison of the microbial ecology associated with monochloramine treatment versus no on-site treatment would yield highly dissimilar bacterial communities. Hot water samples were collected monthly from 7 locations for three months from two buildings in a Pennsylvania hospital complex supplied with common municipal water: (1) a hospital administrative building (no on-site treatment) and (2) an adjacent acute-care hospital treated on-site with monochloramine to control Legionella spp. Water samples were subjected to DNA extraction, rRNA PCR, and 454 pyrosequencing. Stark differences in the microbiome of the chloraminated water and the control were observed. Bacteria in the treated samples were primarily Sphingomonadales and Limnohabitans, whereas Flexibacter and Planctomycetaceae predominated in untreated control samples. Serendipitously, one sampling month coincided with dysfunction of the on-site disinfection system that resulted in a Legionella bloom detected by sequencing and culture. This study also demonstrates the potential utility of high-throughput DNA sequencing to monitor microbial ecology in water systems.

Fungal diversity and presence of potentially pathogenic fungi in a hospital hot water system treated with on-site monochloramine

Currently, our knowledge of fungal ecology in engineered drinking water systems is limited, despite the potential for these systems to serve as a reservoir for opportunistic pathogens. In this study, hot water samples were collected both prior to and following the addition of monochloramine as an on-site disinfectant in a hospital hot water system. Fungal ecology was then analyzed by high throughput sequencing of the fungal ITS1 region. The results demonstrate that the genera Penicillium, Aspergillus, Peniophora, Cladosporium and Rhodosporidium comprised the core fungal biome of the hospital hot water system. Penicillium dominated the fungal community with an average relative abundance of 88.89% (±6.37%). ITS1 sequences of fungal genera containing potential pathogens such as Aspergillus, Candida, and Fusarium were also detected in this study. No significant change in fungal community structure was observed before and after the initiation of on-site monochloramine water treatment. This work represents the first report of the effects of on-site secondary water disinfection on fungal ecology in premise plumbing system, and demonstrates the necessity of considering opportunistic fungal pathogens during the evaluation of secondary premise plumbing disinfection systems.

Shift in the microbial ecology of a hospital hot water system following the introduction of an on-site monochloramine disinfection system.

Drinking water distribution systems, including premise plumbing, contain a diverse microbiological community that may include opportunistic pathogens. On-site supplemental disinfection systems have been proposed as a control method for opportunistic pathogens in premise plumbing. The majority of on-site disinfection systems to date have been installed in hospitals due to the high concentration of opportunistic pathogen susceptible occupants. The installation of on-site supplemental disinfection systems in hospitals allows for evaluation of the impact of on-site disinfection systems on drinking water system microbial ecology prior to widespread application. This study evaluated the impact of supplemental monochloramine on the microbial ecology of a hospital’s hot water system. Samples were taken three months and immediately prior to monochloramine treatment and monthly for the first six months of treatment, and all samples were subjected to high throughput Illumina 16S rRNA region sequencing. The microbial community composition of monochloramine treated samples was dramatically different than the baseline months. There was an immediate shift towards decreased relative abundance of Betaproteobacteria, and increased relative abundance of Firmicutes, Alphaproteobacteria, Gammaproteobacteria, Cyanobacteria and Actinobacteria. Following treatment, microbial populations grouped by sampling location rather than sampling time. Over the course of treatment the relative abundance of certain genera containing opportunistic pathogens and genera containing denitrifying bacteria increased. The results demonstrate the driving influence of supplemental disinfection on premise plumbing microbial ecology and suggest the value of further investigation into the overall effects of premise plumbing disinfection strategies on microbial ecology and not solely specific target microorganisms.

Monochloramine and chlorine dioxide for controlling Legionella pneumophila contamination: biocide levels and disinfection by-product formation in hospital water networks

Legionella colonization in hospital hot water distribution networks was evaluated following 36 months of continuous treatment with monochloramine and compared with chlorine dioxide. Nitrite, nitrate, chlorite, chlorate, bromide, trihalomethanes and haloacetic acids as well as the biocide concentration at sampled points were measured. Only 8/84 samples treated with monochloramine were found contaminated and after the first 8 months of treatment no Legionella was isolated. Chlorine dioxide was associated with a strong reduction in Legionella contamination compared to pre-treatment, but differences according to the device were observed. Monochloramine between 2 and 3 mg l(-1) and chlorine dioxide between 0.50 and 0.70 mg l(-1) were needed to control Legionella colonization. Comparing no- and post-flush samples, a higher frequency of no-flush positive samples was noted using chlorine dioxide, suggesting an increased risk for patients when they open the tap. No increase in chlorite levels and no water nitrification occurred by using monochloramine. Chlorite at levels exceeding the limit requested for drinking water was measured when chlorine dioxide was applied. In conclusion, we highlight that continuous injection of monochloramine should be considered as an effective alternative to chlorine dioxide in controlling legionellae contamination inside hospital water distribution systems.

Molecular Detection of Mycobiota in Drinking Water at Four Different Sampling Points of Water Distribution System of Jeddah City (Saudi Arabia)

The study included collection of water samples (150 samples) from 10 different branches belonging to each water network in Jeddah City (Saudi Arabia). Samples included treated water (30 samples) and tap water in some hospitals (30 samples from cold water tap and 30 samples from hot water tap) and private houses (60 samples). According to results of the traditional identification methods, the highest isolation frequency of fungi was recorded in the private homes (90%), whereas the total isolation frequency was 73.3%. Molecular genetic methods, including PCR amplification and sequencing of ITSs of unculturable fungi, were also considered. All of the sequenced strains were identified by similarity searches with ITS sequences in EMBL/GenBank. All strains that were detected in the examined water samples, which collected from treatment stations and private houses, could be defined by traditional methods. We detected Acremonium strictum as an unculturable strain in hospital cold water. Also, three fungal species were detected in hospital hot water (HHW) by both the traditional methods and the methods of molecular diagnostics (partial sequencing of the ITS gene). In addition, 6 other species including Acremonium strictum, Cladosporium cladosporioides, Rhizopus azygosporus, Penicillium citrinum, Penicillium oxalicum, and Trichoderma viride were identified using the molecular method but were not phenotypically identified in HHW. It can be concluded that drinking water in Jeddah City contains many different fungal species that do not affect the quality of drinking water. However, some of these strains may cause disease in human beings by producing mycotoxins or by causing allergic responses. This study indicates the importance for quality assurance of applying molecular diagnostic techniques as a rapid and accurate technique for detecting the presence of fungi in potable water.

Control of Legionella Contamination with Monochloramine Disinfection in a Large Urban Hospital Hot Water System

Control of Legionella Contamination with Monochloramine Disinfection in a Large Urban Hospital Hot Water System

Control of Legionella contamination in a hospital water distribution system by monochloramine

We report the results of 1-year application of monochloramine to control Legionella pneumophila contamination in a hospital hot water distribution system. In the main building of the hospital, a device continuously distributing monochloramine was installed. Legionella pneumophila and Pseudomonas spp contamination was followed in comparison with 2 other water networks in the same building using chlorine dioxide. Monochloramine significantly reduced the number of contaminated sites compared with baseline (from 97.0% to 13.3%, respectively), chlorine dioxide device I (from 100% to 56.7%, respectively), and device II (from 100% to 60.8%, respectively). No positive sample exceeded 10(4) colony-forming units/L versus 59.4% at baseline. Monochloramine could represent a good alternative to chlorine dioxide in controlling legionellae contamination in public and private buildings.

Effectiveness of different methods to control legionella in the water supply: ten-year experience in an Italian university hospital

We report our ten-year experience of hyperchlorination, thermal shock, chlorine dioxide, monochloramine, boilers and point-of-use filters for controlling legionella contamination in a hospital hot water distribution system. Shock disinfections were associated with a return to pre-treatment contamination levels within one or two months. We found that chlorine dioxide successfully maintained levels at <100 cfu/L, whilst preliminary experiments gave satisfactory results with monochloramine. No contamination was observed applying point-of-use filters and electric boilers at temperatures of >58°C and no cases of nosocomial legionellosis were detected in the ten-year observation period. Our performance ranking in reducing legionella contamination was filter, boiler, chlorine dioxide, hyperchlorination and thermal shock. Chlorine dioxide was the least expensive procedure followed by thermal shock, hyperchlorination, boiler and filter. We suggest adopting chlorine dioxide and electric boilers in parallel.

An Innovative Method for the Control of Legionella Infections in the Hospital Hot Water Systems with a Stabilized Hydrogen Peroxide-Silver Formulation

Legionella pneumophila contamination of hot water systems are particularly difficult to control due to the optimal growth conditions, protection by biofilms and the fact that chlorine and many other disinfectants are less effective at high temperatures. This paper reports on a 20 month study using an innovative method to control Legionella pneumophila in the closed loop hot water system of a major hospital in Israel, which has suffered a serious out-break of Legionnaires disease in their BMT unit. They had failed to control the Legionella infections by the conventional use of repeated shock treatments with chlorine up to 2000 ppm and by raising the water temperature to 700C. During the period between October 2005 and May 2007 an innovative disinfectant process based on a patented, stabilized, non-toxic, taste free, bactericidal/bacteriostatic, heat resistant formulation of hydrogen peroxide containing a minute amount of oligodynamic silver (commercial name STERIL) was used to effectively disinfect the hot water system and achieve total long term control of Legionella pneumophila. The combined formulation of H2O2 and silver and other metals is some 100 times more powerful as a disinfectant than hydrogen peroxide alone and can provide a long lasting effective disinfectant residual. Our studies show that the formulation's disinfection power increases significantly as water temperature increases which contributes to its effective control of Legionalla bacteria in hot water systems which normally operate at temperatures up to 40-500C. The silver ion deposit on the pipe walls have a bacteriostatic effect. At the end of the 24 month test period it can be stated that the stabilized H2O2-silver formulation effectively controlled Legionella pneumophila in the hospital ward's hot water system for the first time after years of chronic problems and has proved to be a promising and economical option for the long term control of Legionella bacteria in closed loop hot water systems.