Horizontal To Vertical Spectral Ratio Research Articles

Micro Zonation to Earthquake Vulnerability in West Semarang Coastal Indonesia Area Based on HVSR (Horizontal to Vertical Spectral Ratio) Microtremor Method

Micro Zonation to Earthquake Vulnerability in West Semarang Coastal Indonesia Area Based on HVSR (Horizontal to Vertical Spectral Ratio) Microtremor Method

Evaluation of Site Terms for Ground-Motion Models for South America

ABSTRACT The time-averaged shear-wave velocity in the top 30 m, VS30, is used to represent the site condition in many ground-motion models (GMMs). Regionalized GMMs account for regional differences in the ln(VS30) scaling by including region-specific coefficients for the site term. For example, recent GMMs developed for subduction zone earthquakes as part of the Next Generation Attenuation-Subduction (NGA-Sub) project include region-specific VS30 scaling for seven regions: South America, Central America, Japan, New Zealand, Taiwan, Cascadia (Pacific Northwest America), and Alaska. Of these seven regions, South America has the largest within-event standard deviation. One cause for the larger within-event standard deviation is a weaker relation between VS30 and the site term in South America compared to other regions. A cause for this weak correlation is that most of the VS30 values for the South American region in the NGA-Sub data set are based on proxies. The relation between VS30 and the site term improves significantly for periods less than 1 s if only stations with measured VS30 are considered, but the correlation is weak for periods greater than 1 s even for stations with measured VS30, indicating that, for the South America region, VS30 is not well correlated with the deeper shear-wave velocity profile that controls the long-period amplification. To improve the site terms for South America, we develop a model based on the horizontal-to-vertical spectral ratio (HVSR) from microtremors, similar to the approach used by Pinilla-Ramos et al. (2022) for California. The data set includes 660 recordings from 51 earthquakes recorded at 274 sites. The site-term model includes the period-dependent HVSR amplitude and the geometric mean of the average HVSR amplitude over the frequency band of 0.25 to 15 Hz. Including these two parameters reduces the standard deviation of site-specific site terms over the period range 0.3–3 s, with the largest reduction in the period range 1–2 s. This site-term model can be incorporated into subduction GMMs and implemented in probabilistic seismic hazard analyses for South America.

3D shear wave velocity imaging of the subsurface structure of granite rocks in the arid climate of Pan de Azúcar, Chile, revealed by Bayesian inversion of HVSR curves

Abstract. Seismic methods are emerging as efficient tools for imaging the subsurface to investigate the weathering zone. The structure of the weathering zone can be identified by differing shear wave velocities as various weathering processes will alter the properties of rocks. Currently, 3D subsurface modelling of the weathering zone is gaining increasing importance as results allow the identification of the weathering imprint in the subsurface not only from top to bottom but also in three dimensions. We investigated the 3D weathering structure of monzogranite bedrock near the Pan de Azúcar National Park (Atacama Desert, northern Chile), where the weathering is weak due to the arid climate conditions. We set up an array measurement that records seismic ambient noise, which we used to extract the horizontal-to-vertical spectral ratio (HVSR) curves. The curves were then used to invert for 1D shear wave velocity (Vs) models, which we then used to compile a pseudo-3D model of the subsurface structure in our study area. To invert the 1D Vs model, we applied a transdimensional hierarchical Bayesian inversion scheme, allowing us to invert the HVSR curve with minimal prior information. The resulting 3D model allowed us to image the granite gradient from the surface down to ca. 50 m depth and confirmed the presence of dikes of mafic composition intruding the granite. We identified three main zones of fractured granite, altered granite, and the granite bedrock in addition to the mafic dikes with relatively higher Vs. The fractured granite layer was identified with Vs of 1.4 km s−1 at 30–40 m depth, while the granite bedrock was delineated with Vs of 2.5 km s−1 and a depth range between 10 and 50 m depth. We compared the resulting subsurface structure to other sites in the Chilean coastal cordillera located in various climatic conditions and found that the weathering depth and structure at a given location depend on a complex interaction between surface processes such as precipitation rate, tectonic uplift and fracturing, and erosion. Moreover, these local geological features such as the intrusion of mafic dikes can create significant spatial variations to the weathering structure and therefore emphasize the importance of 3D imaging of the weathering structure. The imaged structure of the subsurface in Pan de Azúcar provides the unique opportunity to image the heterogeneities of a rock preconditioned for weathering but one that has never experienced extensive weathering given the absence of precipitation.

Identification of Ground Vulnerability Based on Kg, PGA, and GSS Assessment by Single Station Microtremor in Bendosari Hamlet, Kalasan Village, Yogyakarta

Bendosari Hamlet, Kalasan, Yogyakarta is a research area that is one of the areas affected by the earthquake that occurred on May 27, 2006. The earthquake with a magnitude of 6.4 caused quite severe damage to buildings around the research area. Based on the phenomenon of earthquakes that have occurred, there needs to be further study related to vulnerable areas in the event of another earthquake. Research data is primary data taken using a single statiun microtremor tool with an overall acquisition point of 50 measurement points. This study aims to find out the value of seismic vulnerability index (Kg), Peak Ground Acceleration (PGA), and Ground Shear Strain (GSS). Using the Horizontal to Vertical Spectral Ratio (HVSR) method, the dominant frequency result (f0) and amplification factor value (A0) from data that has been recorded through the microtremor tool. Based on research that has been done, the results are obtained in the f0rm of seismic vulnerability index values that are in the range of 0.49 - 30.18, the value of the acceleration of ground movement is in the range of 0.21 - 0.61 Gal, and the ground shear strain value is in the range of 4 x 10-6 to 38 x 10-5. Point K26 which is the original documentation of buildings affected by the earthquake, analyzed that the value of Vs of 858.112 m / s on the vs ground profile indicates that there is hard soil at a depth after 27.2 m. This shows that the thickness of subsurface sedimentary rocks at point K26 is quite thick. Keywords: Bendosari Hamlet; Mikrotremor; GSS; HVSR; PGA; Seismic Vulnerability

Seismic characterisation of the subsoil under a historic building: Cathedral Church of Saint Mary in Murcia case study

This research focuses on the Cathedral Church of Saint Mary in Murcia, Spain, which is located in a moderate-to-high seismic risk zone in the Spanish context. The study uses geophysical techniques and geotechnical investigation to characterise seismic ground models at the building's scale, aiming to understand the real amplification of the ground under seismic effect in historic buildings. Three soil layers (silt, sand with gravel, and gravel) were identified through core borings. Multichannel Analysis of Surface Waves (MASW) profiles and Mini-array profiles revealed Vs values of 305 ± 32 m/s, 296 ± 62 m/s, and 440 ± 38.5 m/s, respectively, for these materials. Seismic Refraction Tomography (SRT) showed Vp values of 586 ± 73 m/s, 700 m/s, and 1466 ± 489 m/s for the corresponding layers. The horizontal-to-vertical spectral ratio (HVSR) approach identified a ground predominant period ranging from 0.37 to 0.38 s. Another significant peak at 2.3 s is observed, probably associated to the Triassic basement. Three seismic events with magnitudes Mw between 4.9 and 5.1 were used as inputs to determine the amplification factor (AF). The results indicate a PGA amplification factor between 1.7 and 2.1. These results contribute to the conservation and mitigation of seismic risk of this cultural heritage generating input data that enables precise computation of the soil-structure interaction.

Assessing soil vulnerability in Petobo post-liquefaction zone, Palu, Central Sulawesi: A microzonation study utilizing microtremor measurements

On September 28, 2018, a 7.5 Richter magnitude earthquake struck the Palu City neighborhood of Petobo. The tectonic activity along the Palu-Koro fault generated this earthquake, which resulted in soil liquefaction. The purpose of this study is to use microtremor measurements at 33 distinct places to investigate the properties of the soil layer after liquefaction. The obtained data was then evaluated utilizing Horizontal to Vertical Spectral Ratio (HVSR) methodologies such as Ground Shear Strength (GSS), amplification factor, and vulnerability index to determine the soil layer's properties and susceptibility. The dominant frequency ranges from 0.19 to 4.75 Hz, while the dominant period ranges from 0.21 to 5.17 seconds, according to the measurement results. According to these measurements, the silt layer varies between 5 and 30 m. GSS values in the 10-4 to 10-2 range indicate that soil cracking, subsidence, liquefaction, landslides, and compaction are likely. The soil vulnerability and amplification index values range from 2.36 to 4.37, respectively. These values show the potential level of danger, which might be low, medium, high, or extremely high. Peak ground acceleration varied from 299.52 to 301.52 gals, suggesting high to extremely high danger levels. The microzonation map created for this study is considered to be a useful resource for training disaster mitigation approaches and facilitating infrastructure development planning in the region.

Distribusi Kerentanan Seismik di Wilayah Pusat Kota Surabaya

Surabaya is the second major city of Indonesia and the economic capital of eastern Indonesia. The city’s central area is the governmental center of East Java Province. This area is traversed by the Surabaya section of the Kendeng Fault which could potentially generate a maximum M6.5 earthquake. The East Java megathrust zone also threatens this area with a potential maximum magnitude of M8.9 earthquake. The rock geology of this region is dominated by soft alluvial soil which could amplify earthquake shaking. This study aims to identify the distribution of seismic vulnerability index in Surabaya’s central area. Therefore, microtremor measurements were carried out at 61 points in this area. The results were then analyzed using the Horizontal to Vertical Spectral Ratio (HVSR) method to determine the amplification factor values and seismic vulnerability index. The results of the HVSR analysis show that the amplification factor value and seismic vulnerability index are in the low to medium category ranging from 0.8370 - 3.8298 and 0.6041 - 14.6268, respectively. The distribution of the results shows that the northern area is more vulnerable than the southern part. This is verified by the geological conditions of the northern part which is dominated by alluvial soil.

Determination of the VS profile at a “noisy” industrial site via active and passive data: The critical role of Love waves and the opportunities of multicomponent group velocity analysis

To define the procedures necessary to unambiguously define the subsurface model, a comprehensive set of active and passive seismic data was collected in an industrial area characterized by an extremely high level of background microtremors. Passive data are recorded to define three observables: the dispersion curve of the vertical component of Rayleigh waves via miniature array analysis of microtremors, the Love-wave dispersion curve via extended spatial autocorrelation, and the horizontal-to-vertical spectral ratio (HVSR). Active data used for the holistic analysis of surface waves are extracted from data recorded through a hybrid acquisition procedure accomplished with only two 3C geophones used to simultaneously define the HVSR at two points. Defined observables are combined according to three different approaches: the joint analysis of Rayleigh waves and HVSR, the joint analysis of Rayleigh and Love waves together with the HVSR, and the joint analysis of multicomponent group velocities together with the HVSR and Rayleigh-wave particle motion (RPM) curves. In agreement with the theory, data indicate that, in general, surface-wave modeling cannot be performed considering modal dispersion curves: dispersion obtained from passive data needs to be modeled considering the effective curve, whereas group velocity obtained from active data can be analyzed using the full velocity spectrum technique. Results indicate that joint inversion of Rayleigh-wave dispersion and HVSR does not necessarily ensure the correctness of the obtained S-wave velocity ([Formula: see text]) profile and that Love waves represent a key observable to fully constrain an unambiguous inversion procedure. However, the joint analysis of multicomponent group velocity spectra (from active multicomponent single-offset data) together with the HVSR and RPM curves is a further efficient way to obtain robust [Formula: see text] profiles through the active and passive data obtained by a single 3C geophone.

The Combination of Hvsr and Masw Methods with Landsat 8 Imagery to Assess the Changing Shoreline along the Coastal Area of Central Bengkulu

The Central Bengkulu Regency possesses a coastline measuring 21.8 km, situated in direct proximity to the Indian Ocean. The heightened wave and ocean current dynamics possess the capacity to induce detrimental effects in the form of coastal abrasion along the coastline. This study conducted an examination of the rate of shoreline changes resulting from coastal abrasion in Central Bengkulu Regency, Bengkulu, Indonesia. Horizontal-to-vertical spectral ratio (HVSR) analysis, multichannel analysis of surface waves (MASW), and Landsat-8 remote sensing were all used in the current investigation. The project gets started with conducting field investigations and measurements of geophysical techniques, including the collection of Landsat-8 satellite imagery spanning the period from 1990 to 2020. Additionally, an examination was conducted on the rate at which the shoreline undergoes changes in velocity. In order to determine the increase in change that occurs along coastlines over a period of several decades, a study was carried out during which Landsat-8 satellite images were analyzed. This study investigates the application of the HVSR technique for assessing the seismic vulnerability of the ground and, additionally, the MASW technique for measuring the shear wave velocity of the coastline’s soil. Both of these methodologies are compared and contrasted with one another in this research. The findings indicated that the mean pace of coastline change in Central Bengkulu Regency was 1.5 m/yr, with the maximum velocity recorded at 4.1 m/yr. This high velocity of shoreline change is correlated with the Vs30 value of MASW measurement and Kg of HVSR measurement, where the subsurface soil structure along the coast of Central Bengkulu Regency from Vs30 measurement shows that it is dominated by stiff soil structure that is susceptible to erosion. Outcomes from the study can inform decision-making processes about safeguards and preventative measures to prevent further coastal degradation. HIGHLIGHTS In this paper, we present a framework using application passive and active seismic method with Landsat 8 for knowing the changing of shoreline coastal area in Central Bengkulu Indonesia This study demonstrated that the high velocity of the shifting shoreline is correlated with Vs30 and Kg values The subsurface soil structure is predominantly composed of stiff soil, and the changing shoreline starts at 1.5 mm/yr, which makes the coast of Central Bengkulu vulnerable to erosion GRAPHICAL ABSTRACT

Seismic microzonation and soil-structure resonance analysis in Suryabinayak Municipality, Bhaktapur, Nepal: insights from ambient vibration measurements

Bhaktapur, lying in the Kathmandu Basin, suffered damages during the 2015 Gorkha Earthquake, potentially exacerbated by local site effects. This research addresses the lack of site response study on Suryabinayak Municipality, located in the southern part of Bhaktapur district. Horizontal to Vertical Spectral Ratio (HVSR) and Floor Spectral Ratio (FSR) methods were employed to determine the fundamental frequencies of soil deposits at 241 free field stations and 20 Reinforced Concrete (RC) isolated buildings respectively. The fundamental frequency of soil deposits varies from 0.27 Hz to 10.00 Hz. Higher frequencies were noted near the basin edges, attributed to shallow sediment deposits, whereas a lower frequencies prevailed towards the basin centre due to an increase in sediment thickness. Out of 20 buildings studied, 7 are highly susceptible to soil-structure resonance as the frequency disparity between building and free-field is less than 15%. This research not only quantified the frequency distribution and soil-structure resonance likelihood but also established a correlation between building height and its fundamental frequency. A significant correlation is observed with a coefficient of determination (R2) value of 60.64% and 83.36% in the longitudinal and transverse directions respectively. The study’s results can be endorsed to mitigate seismic hazards, build seismic-resilient structures, and maintain historical monuments.

Microtremor Full-Wavefield Modeling of Effective Phase Velocity and Horizontal-to-Vertical Spectral Ratio at Kyoto Reference Borehole Site: Comparison with Surface-Wavefield Modeling Based on a Velocity Structure with a Cap Layer

ABSTRACT Two types of data commonly used for microtremor exploration are phase-velocity dispersion curves obtained through an array measurement and horizontal-to-vertical spectral ratios (HVSRs) obtainable by a single-station measurement. Phase-velocity dispersion curves obtained by applying the spatial autocorrelation method to the array waveforms have a characteristic peaked shape in some cases. This dispersion curve shape has traditionally been explained as a consequence of the predominance of higher modes over fundamental mode in the Rayleigh waves. In this study, the effects of body waves on phase velocities and HVSRs were investigated based on both field measurements and theoretical calculations of microtremors. We used vertical-component array waveforms and single-station three-component waveforms of microtremors, obtained at and around a site where combined P-wave–S-wave (PS) and density loggings were conducted in the Kyoto basin, Japan (site KD-1), to identify phase velocities and HVSRs at frequencies in the range 0.2–2 Hz. The corresponding theoretical phase velocities and HVSRs were identified using full-wavefield synthetic data, which were generated assuming excitation points randomly distributed over the surface of a horizontally stratified velocity structure model created based on the logging data. The following key results were obtained. The measured phase-velocity dispersion curve exhibits a peaked shape with the value exceeding the S-wave velocity of the Tamba Group (Tb-Group), which is the bedrock (half-space) of the velocity structure model. Theoretical calculations based on the surface-wavefield theory were unable to reproduce this peaked shape; however, theoretical calculations based on the full-wavefield theory reproduced it with extraordinary accuracy. To reproduce the peaked shape based on the surface-wavefield theory, it was necessary to construct a model containing a cap (i.e., high-velocity layer) connected under the Tb-Group. The theoretical calculation based on the full wavefield also accurately reproduced the peak value and peak frequency of the measured HVSRs.

Spectral ratio analysis of the site amplification effect and nonlinear site response at MYGH10 during the 2021 MW 7.1 Fukushima earthquake in Japan

AbstractGround motion recording with peak ground acceleration (PGA) exceeding 1.43 g was observed at the Yamamoto (MYGH10) station during the MW 7.1 Fukushima earthquake off the east coast of Honshu, Japan, in February 2021. In this study, we investigated the site amplification effect and nonlinear site response at the MYGH10 site using the horizontal‐to‐vertical spectral ratio (HVSR) and surface‐to‐borehole spectral ratio (SBSR), respectively. The site transfer function of station MYGH10 was presented using HVSRs (HVSR on the ground surface) and SBSR at different frequency bands. The dominant contributing frequency band of the PGA was determined by increasing the high cutoff frequency of the bandpass filter when filtering the acceleration recording, which was used to interpret the anomaly of the PGA by combining it with the site characteristics. We found an obvious site effect below the downhole sensor through the HVSRb (HVSR on the downhole bedrock) and determined the influence of the frequency band of the downhole site on ground motion. In addition, substantial discrepancies in the frequency and amplitude between the spectral ratio curves for the Fukushima mainshock records and the weak historical motions were identified. The calculated values of the degree of nonlinearity suggested that a strong nonlinear site response occurred at station MYGH10. Finally, the recovery of the site after strong shaking was evaluated by using the average spectral ratio curves of several aftershock records.

Micro-Zonation of hot spring manifestation site at Umbul Niti, South Lampung based on microtremor

In 2021, an intriguing event unfolded at Umbul Niti village when a resident’s well drilling endeavor unexpectedly yielded to a hot spring, thus transforming the site into a small local tourist attraction that captivates visitors and enhances local economies. However, it is crucial to prioritize the safety of visitors and infrastructure, considering the geological implications of hot springs are related to unstable weak zones that would be severely damaged when an earthquake strikes. Weak zones often exhibit heightened susceptibility to seismic events. Using Horizontal to Vertical Spectral Ratio (HVSR) analysis of micro-tremor data that was recorded for 40 minutes at 25 locations, the Amplification (A 0) and Natural Frequency (f 0) were obtained; then the Seismic Vulnerability Index (Kg ) were calculated. The study area has a dominant frequency of around 4.74 - 9.7 Hz indicating the dominance of hard Tertiary Type I soil from Lampung Formation (QTI). Kg value ranges from 0.08 - 3.57 interpreted as mostly low hazard level. However, in the NW - SE direction the value indicates a high Kg value which means a relatively high hazard level, passing through the hot spring location. Thus, the area at the NW-SE zone might require more specific treatment.

A Seismic Monitoring Tool for Tidal-Forced Aquifer Level Changes in the Río de la Plata Coastal Plain, Argentina

Ambient seismic noise has gained extensive applications in seismology and plays a pivotal role in environmental seismic studies. This study focuses on the Río de la Plata Coastal Plain, employing the horizontal-to-vertical spectral ratio (HVSR) method on ambient seismic noise records to analyze subsurface dynamics. The region’s hydrogeology is complex, featuring partially interconnected coastal aquifers. The HVSR analysis reveals two peaks, with P0 associated with the sediment-basement interface and P1 linked to a shallower stratigraphic discontinuity. Temporal analysis of P1 highlights cyclical patterns correlated with estuarine levels, suggesting a relationship between variations in seismic velocities and tidal dynamics. Comparisons with aquifer data support the hypothesis that tidal variations influence subsurface mechanical properties, impacting the HVSR function. The study hints at the potential of ambient seismic noise analysis as a non-invasive and cost-effective method for studying coastal aquifers and understanding groundwater dynamics. Ongoing research aims to further explore these relationships for enhanced groundwater resource management.

MICROZONATION ANALYSIS IN MANNA CITY & PASAR MANNA SUBDISTRICTS UTILIZING MICROTREMOR DATA, SOUTH BENGKULU REGENCY

South Bengkulu is prone to earthquakes because it is located on the Great Sumatran Fault. Apart from that, it is also influenced by the activity of the Musi and Manna segments, so that besides being influenced by the two active tectonic plates it is also influenced by the local segment. This research is located in Manna City and Manna Market, which is mostly inhabited by people and is the capital of South Bengkulu. In connection with infrastructure development, it is necessary to know the condition of the soil layers to minimize the risk of building damage due to earthquakes. This research aims to analyze earthquake-prone areas based on dominant frequency parameters, soil amplification, seismic vulnerability index and sediment layer thickness (h). Research data comes from microtremor measurements at 60 measuring station points in Manna City and Manna Market. The tool used is a Short Period Portable Seismometer Model Gemini 2 SN-1405. This microtremor data is processed using the Horizontal to Vertical Spectral Ratio (HVSR) method. The results of data processing show that the research area has the lowest dominant frequency of 3.95 Hz and the highest of 49.71 Hz. The ground vibration amplification value is classified as small to medium, the lowest is 1.3 and the highest is 5.19. The lowest earthquake vulnerability index was 0.18 cm2/s and the highest was 2.24 cm2/s. The smallest sediment thickness was 3.77 meters and the thickest was 47.48 meters. From the results of the calculation of the seismic vulnerability index in Kota Manna and Pasar Manna Districts, the seismic vulnerability index value is relatively small, in accordance with the amplification factor and the thickness of the sediment layer. Based on this research, although Manna City and Manna Market are often shaken by earthquakes, the earthquake vibrations experience small amplification.

Local site effects and seismic microzonation around Suban Area, Curup Rejang Lebong, Bengkulu deduced by ambient noise measurements

BackgroundThe Suban area of Curup Rejang Lebong is a tourist region in Bengkulu Province, Indonesia, close to the active Ketaun and Musi faults, which are segments of the Sumatra Fault System (SFS). However, no studies have been conducted in this area to assess how geological structures affect seismic ground motions and contribute to seismic hazard and risk assessment.MethodsThe first study of seismic microzonation in the Suban area of Curup City by ambient noise measurements was conducted at 100 sites, spaced ~ 1 km apart, with 60 min of data acquisition for each site. All microseismic data were processed using the Horizontal to Vertical Spectral Ratios (HVSR) method.ResultsThe HVSR method revealed the amplification factors (A0) ranging from 1.23 to 8.26 times, corresponding to natural frequency (f0) variations between 1.24 and 9.67 Hz. About 13% and 55% of the sites show high (6 ≤ A0 ≤ 9) and medium (3 ≤ A0 ≤ 6) amplifications, respectively, predominantly in the western parts of the study area, consistent with a high seismic vulnerability index (Kg). Furthermore, we also estimated the ground shear strain (GSS) of the region using the Kanai method with two large historical earthquakes at the Ketahun segment in 1943 (Mw 7.4) and the Musi segment in 1979 (Mw 6.0). The Kg value is consistent with the GSS values and indicates areas of severe damage during the historic earthquakes.ConclusionsThus, the western parts of the Suban region are vulnerable to severe damage from an earthquake. These findings could provide valuable insights for future planning and risk management efforts aimed at minimizing the impact of earthquakes in the Suban region.

Shear-Wave Velocity Model from Site Amplification Using Microtremors on Jeju Island

This study examines shear-wave velocity structures in the Jeju region utilizing horizontal-to-vertical spectral ratios (HVSRs) of environmental noise, focusing on identifying significant low-velocity layers (LVLs). Although conventional methodologies predominantly involve borehole and active seismic exploration, recent advancements in the diffuse-field theory of seismic waves have offered a theoretical foundation for this approach. In the volcanic region of Jeju Island characterized by unique geological features, a pervasive LVL composed of quaternary marine sediments and the Seoguipo sedimentary layer has been observed. These components are crucial for site amplification and attenuation in seismic microzonation. The present study introduces a novel discovery of a distinct LVL, specifically at the UDO site, suggesting that its origin may be attributable to a local magmatic intrusion event. Advanced algorithms and HVSR curve analysis have enabled reliable inversion processes, enhancing the comprehension of the subsurface geology of Jeju. These insights are essential for seismic microzonation practices and contribute significantly to the development of seismic design standards in the Jeju region.

DETERMINATION OF SAND MINING PROSPECTIVE ZONES BASED ON SEDIMENT THICKNESS ANALYSIS USING HVSR MICROTREMOR AND GRAVITY METHODS: A CASE STUDY IN CANGKRINGAN, SLEMAN, DAERAH ISTIMEWA YOGYAKARTA

Mount Merapi is the most active type A volcano, especially on the island of Java. It produces sediment products totaling 140 million m3 located at the peak of Mount Merapi, descending through the mountain slopes to rivers originating from Mount Merapi. This sediment is subsequently utilized as a sand mining area. Therefore, it is necessary to determine prospect zones for sand mining that align with environmental, economic, and mitigation aspects in the Cangkringan area, Sleman, Yogyakarta Special Region. Seventeen microtremor measurement points were used with the Horizontal to Vertical Spectral Ratio (HVSR) method to determine sediment thickness, constituent lithology, and mining zones suitable for safety and mitigation aspects. Additionally, the gravity method was employed with 247 measurement stations obtained from GGM Plus to determine rock density and estimated thickness based on 2.5D modeling. The study resulted in the distribution of dominant soil frequencies ranging from 0.5 Hz to 7.5 Hz. High frequencies indicate old rocks, while medium frequencies suggest alluvial rocks with a thickness of ± 5 m. Low frequencies indicate alluvial rocks with a thickness exceeding ± 30 meters. Based on gravity results, the average depth is ±90-200 m with a density of 2.6 g/cm3, reflecting the depth of the bedrock in the study area, composed of andesitic volcanic rock. Soil vulnerability analysis in the study area classified into three categories, with values of 4.2-5.4 being highly vulnerable to surface deformation, values of 1.8-3.8 indicating moderate vulnerability, and values of -0.2-1.4 representing low vulnerability. Furthermore, the Peak Ground Acceleration (PGA) ranges from 500-1200 gal with intensity X. Ground Shaking Spectrum (GSS) data indicates that the study area experiences vibration phenomena with elastic soil dynamics. Therefore, the exploitation of sand resources in the Cangkringan area can be conducted in the southern region of Mount Merapi, approximately 2 km away from the mountain center. This is because the southern part of the research area has suitable mitigation measures. Moreover, based on the analysis, sediment thickness in this area ranges from ± 5-30 meters.

Identification of Landslide-prone Areas on the Road Connecting Kaur Regency, Bengkulu Province to South Oku Regency, South Sumatra Province Using the Microtremor Method

Muara Sahung District, Kaur Regency, is an area with a high level of landslide disasters. These incidents often cut off the connecting transportation route between Kaur Regency, Bengkulu Province, and South Oku Regency, South Sumatra Province. This research aims to analyze the potential for landslide disasters in this area. We used the Horizontal to Vertical Spectral Ratio (HVSR) technique to analyze microtremors and identify landslide-prone areas in this research. A total of 13 measurement points with a distance of 1–3 km between points are located in Serdang Indah Village, Luas District, Ulak Bandung Village, Bukit Makmur and Sumber Makmur, Muara Sahung District, Kaur Regency, Bengkulu Province. This was carried out using the PASI Gemini-2 portable seismometer device in the Kaur Regency area with hilly contours on the left and right of the road. The analysis results include the amplification factor (A0), dominant frequency (f0), and soil vulnerability index (Kg). The results of the analysis and calculations show that the highest landslide risk value among all points is at point (KR-4, KR-5) in Ulak Village, Bandung (KR-7). Bukit Makmur Village and (KR-9) Serdang Indah Village, where this location is on a road with steep hilly contours that often cause landslides.

ZONATION OF SEISMIC VULNERABILITY LEVELS IN SOUTH BENGKULU REGENCY, INDONESIA FOR DISASTER-BASED REGIONAL PLANNING

The accurate prediction and prevention of earthquakes remains challenging. Consequently, the primary approach to mitigate the impact of earthquakes is through disaster risk reduction efforts. One significant strategy involves conducting seismic vulnerability analyses based on disaster scenarios. This study aims to identify and map areas with varying levels of seismic vulnerability, analyzing the factors contributing to vulnerability in the South Bengkulu Regency. Secondary data, including peak ground acceleration (PGA) values, were collected, along with microtremor data obtained through the Horizontal to Vertical Spectral Ratio (HVSR) method. The recorded microtremor data serve as input parameters for PGA, Modified Mercalli Intensity (MMI), Seismic Vulnerability Index (Kg), shear wave velocity (Vs), and the time-averaged shear wave velocity for the first 30 m depths (Vs30) values. The findings reveal that, overall, seismic vulnerability in the South Bengkulu Regency can be categorized as low. However, specific areas, particularly in the southwestern and northeastern zones, exhibit relatively higher levels of vulnerability. The heightened vulnerability in these areas is attributed to elevated PGA values, despite the region's generally high soil density, which acts as a mitigating factor against earthquake threats.