Homogeneous Stress Distribution Research Articles

Stress-strain state of implant-supported restorations in tooth replacement

Background: Dental implant therapy may be associated with breakage and deformation of implant-supported restorations, necessitating an assessment of their stress-strain state when applying a load. Aim: To compare the stress-strain state of implants with their respective fixed restorations in tooth replacement. Materials and Methods: A 3D mathematical model of the posterior mandible with three missing teeth was used to assess the stress-strain state for the following dental restoration options: three implant-supported crowns; a two-implant-supported bridge; or a bridge supported by tooth and implant. A 150 N load was applied to the central part of a restoration in both vertical and oblique directions to compare maximum stress values and their distribution. Results: Oblique load was found to have a negative impact on stress intensity and distribution (471.7 MPa vs 90.7 MPa with vertical load for three implants). The most heavily loaded parts of restorations were identified: the border of the crown and the implant connection zone. A homogeneous stress distribution from a bridge to the two supporting implants was observed, along with a decrease in stress when using a bridge rather than three implant-supported crowns (160.0 MPa vs 16.1 MPa). In contrast, the load on the supporting implant increased when a bridge supported by tooth and implant was used (1,053.5 MPa with oblique load). Conclusion: Compared to three implants replacing three missing teeth, a two-implant-supported bridge decreases stress on the implants and their respective restoration. Replacing one supporting implant with a tooth increases stress on the implant to the ultimate strength of titanium alloy in the abutment.

High-Entropy Layered Oxide Cathode Materials with Moderated Interlayer Spacing and Enhanced Kinetics for Sodium-Ion Batteries.

Sodium-ion batteries (SIBs) with low cost and environmentally friendly features have recently attracted significant attention for renewable energy storage. Sodium layer oxides stand out as a type of promising cathode material for SIBs owing to their high capacity, good rate performance, and high compatibility for manufacturing. However, the poor cycling stability of layer oxide cathodes due to structure distortion greatly impacts their practical applications. Herein, a high entropy doped Cu, Fe, and Mn-based layered oxide (HE-CFMO), Na0.95Li0.05Mg0.05Cu0.20Fe0.22Mn0.35Ti0.13O2 for high-performance SIBs, is designed. The HE-CFMO cathode possesses high-entropy transition metal (TM) layers with a homogeneous stress distribution, providing a moderated interlayer spacing to maintain the structure stability and enhance Na+ ion diffusion. In addition, Li doping in TM layers increases the Mn valence state, which effectively suppresses John-Teller effect, thus stabilizing the layered structure during cycling. Furthermore, the use of nontoxic and low-cost raw materials benefits future commercialization and reduces the risk of environmental pollution. As a result, the HE-CFMO cathode exhibits a super cycling performance with a 95% capacity retention after 300 cycles. This work provides a promising strategy to improve the structure stability and reaction kinetics of cathode materials for SIBs.

Fracture behavior of SiCf/SiC cladding with prefabricated cracks on the inner/outer wall

This study investigated the fracture behavior of SiCf/SiC cladding with axial cracks in the CMC layer/monolithic SiC layer on the inner and outer wall via an expanding plug test. The specimen with a prefabricated crack on the outer wall fractured in no specific direction. After the first load drop, fracture sources can be detected not only near the notch but also in other directions within the CMC layer. The simulation shows a homogeneous stress distribution resulting in a similar hoop strength to the specimen without prefabricated cracks. In contrast, the specimen with a prefabricated crack on the inner wall fractured along the notch. After the first load drop, fracture sources can be detected only near the notch. The simulation demonstrates stress concentration, resulting in a lower hoop strength. Therefore, considering the nuclear application of SiCf/SiC cladding, we are supposed to pay more attention to the defects in CMC layer in the fabrication process of SiCf/SiC cladding.

Influence of connection design and material properties on stress distribution and fatigue lifetime of zygomatic implants: A finite element analysis

Zygomatic implants (ZIs) were developed as a graftless alternative to rehabilitate severely reabsorbed maxillae. This study aims to employ three-dimensional finite element analysis (FEA) to simulate the impact of external hexagonal implant connection (EHC) and internal hexagonal implant connection (IHC) on the stress distribution and fatigue lifetime within the ZI systems using parameters defined in ISO 14801:2016. Two ZI assemblies (Nobel Biocare and Noris Medical) were scanned in a micro-CT scanner and reconstructed using Nrecon software. Three-dimensional models were generated by Simpleware ScanIP Medical software. All models were exported to FEA software (ABAQUS) and subsequently to a fatigue analysis software (Fe-safe). A compressive 150 N load was applied at a 40° angle on the cap surface. A 15 Hz frequency was applied in the in silico cyclic test. The implant components had material properties of commercially pure grade 4 titanium (CPTi) and Titanium-6Aluminum-4Vanadium alloy (Ti64). Von Mises stress data, contour plots, and fatigue limits were collected and analyzed. EHC models exhibited higher peak stresses in implant components for both materials compared to IHC models. However, simulated bone support results showed the opposite trend, with higher stresses on IHCthan EHC models. The fatigue analysis revealed that assemblies with both designs exceeded ISO 14801:2016 number of cycles limits using Ti64, while CPTi groups exhibited comparatively lower worst life-repeats. In conclusion, ZIs with IHC were found to have a more homogeneous and advantageous stress distribution within both materials tested. Ti64 demonstrates a prolonged service life for both design connections.

Constructing unique dual-functional double-hollow architecture for enhanced high-voltage structural stability of layered oxide cathode

Elevating the working voltage has proven to be an effective strategy for enhancing the energy density of ternary layered cathode materials. However, the accelerated failure of secondary particle structure during high-voltage cycling hinders their practical application. Although some attempts have been exerted to address this issue by designing particle arrangement, these secondary structure modifications only provide the limited help to the structural failure problem. Herein, we focus on the cause and characteristic of secondary particle cracks, investigate their formation principle and development rule, and delicately propose a unique double-hollow secondary structure. The two hollow regions create an environment that facilitates the release of internal strain and reduces stress at grain boundaries, thus ensuring the homogeneous stress distribution within the secondary particles. Thereby, the formation of intergranular crack is effectively mitigated. Additionally, the hollow regions act as barrier layers to impede the crack propagation. The dual functions of this double-hollow structure efficiently maintain the tight connection among these primary particles, greatly boosting the high-voltage cycling stability. The designed material with double-hollow architecture exhibits an obvious capacity retention increase from 67.8 % (conventional structure) to 84.4 % at 1 C within 3.0-4.5 V after 300 cycles. This work demonstrates that the double-hollow structure can effectively address the key issues of crack occurrence and development, providing a novel structural design concept for the exploration of high-voltage cathode materials with superior stability.

Examination of Various Abutment Designs Behavior Depending on Load Using Finite Element Analysis.

Studies on dental implant abutments' geometric design and material selection offer significant innovations and results. These studies aim to improve the abutments' functionality and aesthetic performance, minimize microcavities' formation, and ensure implant-supported prostheses' longevity. For example, CAD-CAM fabricated custom abutments have been found to produce a better marginal fit and fewer microgaps than standard abutments. In an in vitro study, transepithelial abutments offered lower microgap values than titanium-based abutments and provided a better fit at the implant-abutment interface. It is known that studies to improve mechanical and biological performance with Polyether Ether Ketone (PEEK) material have been addressed. New materials such as PEEK and zirconia have offered significant advantages in biocompatibility and aesthetics. Along with those studies, different abutment designs are also important. Abutment geometry is optimized to improve stress distribution and minimize peri-implant bone loss. In implant and abutment connections with different angles, mechanical life performances may vary depending on static and dynamic load. These studies emphasize the importance of material research on different types of connections to improve dental implants' durability, homogeneous load distribution, and reliability. The abutment parts used in implant treatment are insufficient to distribute the load homogeneously against chewing pressure due to their materials and geometry. Non-uniform load distribution damages the abutment and the prosthetic crown, accelerating the wear process. This study aimed to create different abutment designs to improve dental implants' biomechanical performance and longevity. This study aimed to increase the mechanical durability of the implant-abutment connection by reducing stress concentrations in response to masticatory compression on the abutment in different directions and forces and to guarantee the long-term success of the implant system by providing a more homogeneous stress distribution. It aimed to apply different forces in the axial direction to these models in a simulation environment and to calculate and compare the deformation and stress load distribution. As a method, three-dimensional models of the parts used in implant treatments and forming the implant system were designed. Different abutment designs were created with these models. Taking the current material values used in implant treatments as a reference, finite element analysis (FEA) was performed by applying different axial loads to each implant system model in the ANSYS software (version 24.1). Comparative analysis graphs were prepared and interpreted for the stress values obtained after the applied load. This study evaluated the mechanical performance of different abutment models (A, B, C, D, and E) under a 100 N load using the Kruskal-Wallis test. The Kruskal-Wallis test showed significant differences between the groups (p < 0.001). The greatest difference was observed between models E and A (q' = 6.215), with a significant difference also found between models C and A (q' = 3.219, p < 0.005). Regarding stress values, the highest stress on the abutment was observed in Model B (97.4 MPa), while the lowest stress was observed in Model E (9.6 MPa). The crown exhibited the highest stress in Model B (22.7 MPa) and the lowest in Model E (17.3 MPa). The implant stress was highest in Model C (14.8 MPa) and lowest in Model B (11.3 MPa). The stress values for the cortical bone and cancellous bone were quite similar across the models, showing no significant differences. These findings indicate that the abutment design and material selection significantly impact mechanical performance. Among the implant systems created with five different abutment models, in which the existing abutment geometry was also compared, homogeneous and axial distribution of the load on the abutment was achieved, especially with viscoelastic and surface area increased abutment designs. Clinically, the inadequacy and limited mounting surface or geometry of the abutments used in today's implant treatment applications have led to different design searches. It was concluded that the designs in this study, which are considered alternatives to existing abutment models, contribute positively to the mechanical life of the abutment material, considering the von Mises stresses and directions. This study brings a new perspective to today's practices and offers an alternative to treatment practices.

Achieving Remarkable Specific Mechanical Strength and Energy Absorption Capacity in SiC Nanowire Networks through Graded Structural Design.

Lightweight porous ceramics with a unique combination of superior mechanical strength and damage tolerance are in significant demand in many fields such as energy absorption, aerospace vehicles, and chemical engineering; however, it is difficult to meet these mechanical requirements with conventional porous ceramics. Here, we report a graded structure design strategy to fabricate porous ceramic nanowire networks that simultaneously possess excellent mechanical strength and energy absorption capacity. Our optimized graded nanowire networks show a compressive strength of up to 35.6 MPa at a low density of 540 mg·cm-3, giving rise to a high specific compressive strength of 65.7 kN·m·kg-1 and a high energy absorption capacity of 17.1 kJ·kg-1, owing to a homogeneous distribution of stress upon loading. These values are top performance compared to other porous ceramics, giving our materials significant potential in various engineering fields.

Stress Distribution within the Peri-Implant Bone for Different Implant Materials Obtained by Digital Image Correlation.

Stress distribution and its magnitude during loading heavily influence the osseointegration of dental implants. Currently, no high-resolution, three-dimensional method of directly measuring these biomechanical processes in the peri-implant bone is available. The aim of this study was to measure the influence of different implant materials on stress distribution in the peri-implant bone. Using the three-dimensional ARAMIS camera system, surface strain in the peri-implant bone area was compared under simulated masticatory forces of 300 N in axial and non-axial directions for titanium implants and zirconia implants. The investigated titanium implants led to a more homogeneous stress distribution than the investigated zirconia implants. Non-axial forces led to greater surface strain on the peri-implant bone than axial forces. Thus, the implant material, implant system, and direction of force could have a significant influence on biomechanical processes and osseointegration within the peri-implant bone.

Biomechanical analysis of push-pull principle versus traditional approach in locking plates for proximal humeral fracture treatment.

Proximal humerus fractures are usually treated with locking plates, which could present recurrence, screw penetration, joint varization. The push-pull principle was introduced to prevent these risks and showed promising results; a dedicated design was then developed and this feasibility study aims to compare the biomechanical performances of such dedicated push-pull plate with the traditional locking plate using finite elements. The humerus geometry was obtained from Sawbone CT-scans; the geometries of a traditional locking plate and of the dedicated push-pull one were used. A fracture was added below the humeral head and the plates were virtually implanted. The wire pulling mechanism was simulated connecting the plate to the humeral head apex, considering two levels of tension. Three testing set-ups (axial, torsion and compression bending) were simulated. Stress distributions on bone, plate and screws were measured. Stress distribution on the distal humerus was similar for both plates. Stress distribution on the proximal humerus was more homogeneous for the push-pull model, showing less unloaded sections (up to 78%). The different levels of tension applied to the wire returned slight differences in terms of stress values, but the comparison with the traditional approach gave similar outcomes. More homogeneous stress distribution is found with the push-pull plate in all three testing set-ups, showing lower unloaded areas (and thus lower stress-shielding) compared to the traditional plate; the screws implemented returned to be all loaded in at least one of the set-ups, thus showing that they all contribute to plate stability.

Stress Analysis on Mesiolingual Cavity of Endodontically Treated Molar Restored Using Bidirectional Fiber-Reinforced Composite (Wallpapering Technique).

Endodontically treated teeth (ETT) undergo extensive structure change and experience high stress during biomechanical function. Stress distribution is influenced by the restoration material and the type of bond between material and tooth structure. The selection of materials that can distribute stress will affect the resistance and retention of ETT to mastication forces, thus biomechanical functions were achieved. Composite has mechanical properties similar to dentin, it can transmit and distribute stresses throughout the tooth surface. The disadvantage of composites in large cavities is their lack of toughness. The addition of fiber to composites can increase their toughness. This research is to determine the stress distribution of a fiber-reinforced composite made of polyethylene and e-glass on the mesiolingual cavity of ETT. A three-dimensional model of the mandibular molar was prepared for cavity preparation and the formation of restorations using SolidWorks 2021. The models were analyzed with Abaqus 2020 to determine stress concentrations after given vertical and oblique loading. The maximum and minimum principal stress data were obtained to assess material resistance and interfacial damage criterion. Polyethylene fiber shows a more homogeneous stress distribution because the modulus of elasticity is close to the dentin and has a thickness that can reduce the volume of the composite. The E-glass shows the stress concentration on the circumferential fiber and cavity floor. The stress distribution of fiber-reinforced composite on the buccolingual cavity of ETT using the finite element method did not show structural failure in the polyethylene group because the maximum and minimum principal stresses were lower than the strength of the material. Interfacial bond failure occurs at the enamel portion. The maximum and minimum principal values of e-glass indicate structural failure in the circumferential fiber and the base fiber because the stress exceeds the strength of the material. Interfacial bond failure occurred on the circumferential and the cavity floor.

Developing Advanced Patient-Specific In Silico Models: A New Era in Biomechanical Analysis of Tooth Autotransplantation

IntroductionAs personalized medicine advances, there is an escalating need for sophisticated tools to understand complex biomechanical phenomena in clinical research. Recognizing a significant gap, this study pioneers the development of patient-specific in silico models for tooth autotransplantation (TAT), setting a new standard for predictive accuracy and reliability in evaluating TAT outcomes. MethodsDevelopment of the models relied on 6 consecutive cases of young patients (mean age 11.66 years ± 0.79), all undergoing TAT procedures. The development process involved creating detailed in silico replicas of patient oral structures, focusing on transplanting upper premolars to central incisors. These models underpinned finite element analysis simulations, testing various masticatory and traumatic scenarios. ResultsThe models highlighted critical biomechanical insights. The finite element models indicated homogeneous stress distribution in control teeth, contrasted by shape-dependent stress patterns in transplanted teeth. The surface deviation in the postoperative year for the transplanted elements showed a mean deviation of 0.33 mm (±0.28), significantly higher than their contralateral counterparts at 0.05 mm (±0.04). ConclusionsBy developing advanced patient-specific in silico models, we are ushering in a transformative era in TAT research and practice. These models are not just analytical tools; they are predictive instruments capturing patient uniqueness, including anatomical, masticatory, and tissue variables, essential for understanding biomechanical responses in TAT. This foundational work paves the way for future studies, where applying these models to larger cohorts will further validate their predictive capabilities and influence on TAT success parameters.

Evaluating High‐Pressure Torsion Scale‐Up

Increasing sample dimensions in high‐pressure torsion (HPT) processing affects load and torque requirements, deformation distribution, and heating. Finite‐element modeling (FEM) and experiments are used to investigate the effect of technical parameters on the scaling up of HPT. Simulations confirm that axial load and torque requirements are proportional to the square and the cube of the sample radius, respectively. The temperature rise also displays a pronounced dependency on the radius. Decreasing the diameter‐to‐thickness ratio can cause heterogeneity in strain distribution along the thickness direction at the edges of the sample. Such heterogeneity is governed by friction conditions between the material and the lateral wall of the anvil depression. Simulation of HPT processing of ring‐shaped samples shows that it is possible to reach more homogeneous distribution of strain and flow stress in the processed material. Experiments using magnesium confirm a tendency for strain localization in the early stage of HPT processing but increasing the number of turns increases the homogeneity of the material. The embodied energy in HPT processing is discussed.

Optimization and Evaluation of Mechanical and Electrochemical Properties of Ferritic Stainless Steel Welding Using Taguchi Design

The main objective of this work is to optimize welding parameters of AISI 430 FSS welds, focused to minimization of ferrite grains size using Taguchi’s design. Two input parameters of speed and welding current; were chosen to select the minimum grain size and to ascertain their effects on ferrite grain size. ANOVA method was used to evaluate the influence of varying factors on the overall quality of welds. Optimal combination of the parameters were be predicted by S/N analyses, it was accessed on employing an 80 A with 6mm/s. Experimental characterizations of optimum weld joint were performed by using tensile test assisted by image correlations, optical and electronic microscopy. As a result, welding speed had the main influence on grain size by 84.30%. Optimum welding parameter offered finest microstructure with low rate of martensite precipitates in both fusion zone and heat affected zone, and best combination of strength and ductility, it presented a homogeneous distribution of tensile stresses that caused a ductile fracture in base material. ,it is found that that optimized welding parameters permit to give greater resistance to corrosion, which exhibit a lower corrosion current, indicating that coarse ferrite grains are more susceptible to corrosion compared to fine grains.

High-energy sputtering for the deposition of a conductive and adherent single molybdenum layer for solar cell applications

Molybdenum (Mo) thin films are thought to be an excellent back contact for CuIn1-xGaxSe2 (CIGS) solar cells. Mo films require high conductivity and good adhesion to glass substrates; however, these characteristics cannot be combined in sputtered Mo under the same deposition conditions. Direct current Magnetron Sputtering (DcMS) and High-Power Impulse Magnetron Sputtering (HiPIMS) were used to deposit Mo films on glass substrates, and the effects of working pressure and substrate bias on their characteristics were investigated. To begin, single layers of Mo were produced at pressures ranging from 0.2 to 1.4 Pa. The Mo films deposited at the lowest working pressure of 0.2 Pa were then subjected to a negative substrate bias varying from -50 to -200 V. All of the HiPIMS films adhered well to the glass substrate, whereas the DcMS films deposited at various pressures showed poor adhesion. Furthermore, our findings demonstrated that applying a negative substrate bias reduced the resistivity of Mo films to the lowest values of 2.56 × 10−5 Ω.cm and 2.771 × 10−5 Ω.cm, respectively, for the HiPIMS and DcMS-deposited films, while improving the adhesion of the DcMS-samples due to the development of films with homogenous stress distribution.

On the mechanical response of graphene-capped copper nanoparticles.

In this study, we investigated the mechanical behavior of pristine copper (Cu) nanoparticles (NPs) and Cu@graphene (Cu@G) hybrid NPs using molecular dynamics simulations. The longitudinal engineering strain was calculated as a measure of compression until reaching 25% of the initial size of the NPs. The stress-strain curves revealed the elastic-to-plastic transition in the Cu NPs at a longitudinal strain of 3.57% with a yield strength of 6.15 GPa. On the other hand, the Cu@G NPs exhibited a maximum average load point at a longitudinal strain of 6.81% with a yield strength of 8.26 GPa. The hybrid Cu@G NPs showed increased strength and resistance to plastic deformation compared to the pure Cu NPs, while the calculation of the elastic modulus indicated a higher load resistance provided by the graphene coverage for the Cu@G NPs. Furthermore, the analysis of atomic configurations, dislocations, and stress distribution demonstrated that the graphene flakes play a crucial role in preventing dislocation events and faceting in the Cu@G NPs by acting as a shock absorber, distributing the applied force on themselves, and producing a more homogeneous stress distribution on the Cu NPs; additionally, they prevent the movement of Cu atoms, reducing the occurrence of dislocations and surface faceting, thanks to their supportive effect. Overall, our findings highlight the potential of hybrid nanomaterials, such as Cu@G, for enhancing the mechanical properties of metallic NPs, which could have significant implications for the development of advanced nanomaterials with improved performance in a variety of applications.

Biomechanical Behavior of Lithium-Disilicate-Modified Endocrown Restorations: A Three-Dimensional Finite Element Analysis

This study aimed to assess the biomechanical behavior of endocrown-restored mandibular molars according to “margin design” and “coverage extent” using finite element analysis (FEA). Six 3D solid models were fabricated, namely, those with complete occlusal coverage: A (butt joint), B (anatomic margin); partial coverage (two mesial cusps): C (butt joint), D (anatomic margin); and partial coverage with mesial class II cavity: E (butt joint), F (anatomic margin). All models received lithium disilicate endocrowns (2.0 mm thickness and 4.0 mm central retainer cavity depth). A 300 N vertical load was applied to the occlusal surface, while a 250 N oblique load was applied at 45° to the lingual inclined planes of the buccal cusps. The maximum von Mises stress (VMS) distribution patterns were calculated for the endocrown, tooth structure, and cement layer. The VMS on the prepared teeth and cement layer showed subtle differences between the tested models under vertical loads. The anatomic margin (partial and complete coverage) exhibited a more homogeneous stress distribution and offered a more adhesive area of the tooth structure. Under oblique loading, the anatomic margin (complete and partial), except Model D, exhibited the lowest VMS in the cement layer. An anatomically based endocrown could be a promising alternative to the butt joint design, providing better-devised endocrown restorations, which could potentially yield a more benign stress dissipation.

Compromised homeostasis in aged carotid arteries revealed by microstructural studies of elastic lamellae

Healthy arteries are continuously subjected to diverse mechanical stimuli and adapt in order to maintain a mechanical homeostasis which is characterized by a uniform distribution of wall stresses. However, aging may compromise the homeostatic microenvironment within arteries. Structural heterogeneity has been suggested as a potential microstructural mechanism that could lead to homogeneous stress distribution across the arterial wall. Our previous study on the unfolding and stretching of the elastic lamellae revealed the underlying microstructural mechanism for equalizing the circumferential stresses through wall; inner elastic layers are wavier and unfold more than the outer layers which helps to evenly distribute lamellar stretching (Yu et al., 2018). In this study, we investigated the effect of aging on lamellar deformation and its implications for tissue homeostasis. Common carotid arteries from aged mice were imaged under a multi-photon microscope while subjected to biaxial extension and inflation at five different pressures ranging from 0 up to 120 mmHg. Lamellar unfolding during pressurization was then determined from the reconstructed cross-sectional images of elastic lamellae. Tissue-level circumferential stretch was combined with the lamellar unfolding to calculate lamellar stretching. Our results revealed that the straightness gradient of aged elastic lamellae is similar to the young ones. However, during pressurization, the inner elastic lamella of the aged mice unfolded significantly more than the inner layer in young arteries. An important finding of our study is the uneven increase in inter-lamellar space which contributed to a nonuniform stretching of the elastic lamellae of aged mice arteries, elevated stress gradient, and a shifting of the load-bearing component to adventitia. Our results shed light into the complex microstructural mechanisms that take place in aging and adversely affect arterial mechanical behavior and homeostasis.

Biomechanical behavior of carbon fiber-reinforced polyetheretherketone as a dental implant material in implant-supported overdenture under mandibular trauma: A finite element analysis study.

Implant-supported overdentures are well-known and widely accepted treatment modality to increase retention which is a crucial factor for determining patient satisfaction. The placement of two implants in the anterior region can be selected as a first-line treatment in patients with the atrophic mandibular ridge. The purpose of this research was to assess the biomechanical effects of carbon fiber-reinforced polyetheretherketone (CFR-PEEK) implant-supported overdenture in the event of 2,000 N forefront trauma to an atrophic edentulous mandible by using the finite element analysis method. Three types of mandible models were simulated; the first one was an edentulous atrophic mandible model; in the second model, 3.5 × 11.5 mm CFR-PEEK implants; and in the third model, 4.3 × 11.5 mm CFR-PEEK implants were positioned in the region of the lateral incisor of the identical edentulous atrophic mandible. Maximum Von Misses stresses 979.261 MPa, 1,454.69 MPa, and 1,940.71 MPa and maximum principal stresses 1,112.74 MPa, 1,249.88 MPa, and 1,251.33 MPa have been detected at the condylar neck area and minimum principal stresses - 1,203.38 MPa, -1,503.21 MPa, and - 1,990.34 MPa have been recorded at the symphysis and corpus regions from M1 to M3, respectively. In addition, the M2 and M3 models showed low-stress distributions around the implant-bone interface, particularly where the implants were in contact with cancellous bone. The results showed that the insertion of different diameters of CFR-PEEK implants led to low and homogenous stress distribution all around the implant-bone interface and stresses transferred directly to the condylar neck areas. Therefore, it was observed that CRF-PEEK implants did not change the basic behavior of the mandibula in response to frontal stresses.

A numerical study on stress mitigation in through-thickness tailored bi-adhesive single-lap joints

In bi-adhesive single-lap joints (SLJs), longitudinal grading of adhesive compliance leads to peak stress concentration to the bi-adhesive interface (due to mismatch in properties). Due to this additional stress concentration at the bi-adhesive interface, the failure initiation threshold is lowered. In this paper, the stress distribution in the compliance-tailored bi-adhesive joints is investigated numerically. Peak stress at the bi-adhesive interface is diffused by geometrically grading the bi-adhesive interface in the longitudinal and transverse (through the thickness) directions. Linear and non-linear (material and geometric) finite element (FE) analyses were performed for two different set of bi-adhesive bondlines and joint configurations. FE results were benchmarked with published experimental and numerical data. Peak peel stress and peak shear stress are decreased by 29–70% and 8%, respectively, when the bi-adhesive interface is graded geometrically in the transverse and longitudinal directions as opposed to longitudinal tailoring alone. Moreover, the bi-adhesive interface’s stress concentration is reduced significantly. This leads to a more homogeneous stress distribution throughout the bond-layer. A thorough investigation reveals that through-thickness compliance tailoring of the bi-adhesive in SLJ can be used to increase tolerance to high load levels, achieve uniform stress distribution along the bond-layer, and reach the optimum joint stiffness.HighlightsA new approach for stress mitigation involving through the thickness tailoring of adhesive is introducedProposed approach is validated for two sets of bi-adhesive systems and two joint configurationsFinite element results are validated with published experimental dataLoad carrying capacity of joints is enhanced by diffusing peak stresses away from the bi-adhesive interface

Fracture toughness of wood and transparent wood biocomposites in the toughest LT-direction

Fracture toughness and mechanisms of crack growth are characterized for transparent wood polymer biocomposites and compared to native wood, with the crack normal to the fiber direction (LT fracture plane). Side-grooved specimen geometries generated pure mode I crack growth, whereas previous investigations commonly report 90° crack path deflection. Crack growth micromechanisms were analyzed by experimental fracture tests and in-situ microscopy observations. Large damage zones around the crack tip with fiber bundle bridging and pull-out were observed in the crack wake, justifying more advanced cohesive zone modeling suitable for composite materials design. The polymer matrix resulted in much higher fracture energy of the biocomposites compared to native wood due to increased local cohesive strength. This strength increased from the polymer contribution and more homogeneous stress distribution in the wood fibers.