Hologram Pattern Research Articles

Detection of viability of micro-algae cells by optofluidic hologram pattern.

A rapid detection of micro-algae activity is critical for analysis of ship ballast water. A new method for detecting micro-algae activity based on lens-free optofluidic holographic imaging is presented in this paper. A compact lens-free optofluidic holographic imaging device was developed. This device is mainly composed of a light source, a small through-hole, a light propagation module, a microfluidic chip, and an image acquisition and processing module. The excited light from the light source passes through a small hole to reach the surface of the micro-algae cells in the microfluidic chip, and a holographic image is formed by the diffraction light of surface of micro-algae cells. The relation between the characteristics in the hologram pattern and the activity of micro-algae cells was investigated by using this device. The characteristics of the hologram pattern were extracted to represent the activity of micro-algae cells. To demonstrate the accuracy of the presented method and device, four species of micro-algae cells were employed as the test samples and the comparison experiments between the alive and dead cells of four species of micro-algae were conducted. The results show that the developed method and device can determine live/dead microalgae cells accurately.

Distortion Compensation of Reconstructed Hologram Image in Digital Holographic Display Based on Viewing Window

A holographic display based on a viewing window enables the converging of a reconstruction wave into a viewing window by means of an optical system. Accordingly, a user can observe a reconstructed hologram image, even with a small diffraction angle. It is very difficult to manufacture an optical system with no aberrations; thus, it is inevitable that a certain amount of wave aberrations will exist. A viewing-window-based holographic display, therefore, always includes distortions in an image reconstructed from a hologram pattern. Compensating the distortions of a reconstructed image is a very important technical issue because it can dramatically improve the performance when reconstructing a digital three-dimensional content image from a hologram pattern. We therefore propose a method for suppressing image distortion by measuring and compensating the wave aberration calculated from a Zernike polynomial, which can represent arbitrary wave aberrations. Through our experimental configuration using only numerical calculations, our proposed method decreased the reconstructed image distortion by more than 28%.

High efficient generation of holographic stereograms based on wavefront recording plane

A computer generated holographic stereogram based on the wavefront recording plane (WRP) is presented. A WRP closed to the parallax image plane is introduced to record the complex amplitude in a small region for each point in the parallax image. By using three times of fast Fourier transform (FFT) to execute the Fresnel diffraction calculation between the WRP and the holographic stereogram plane, the object wave contributing to the hologram pattern can be achieved. The computation complexity of the proposed approach is dramatically reduced. The results show that the calculation time can be decreased by more than one order of magnitude.

Optically Switchable Circularly Polarization-Dependent Optical Vortex

An optical vortex, which consists of blue phase and isotropic phase, is generated from azobenzene liquid crystal cell with computer generated hologram pattern. This device is optically switchable and can be erased and generated by ultraviolet or green light, respectively. An intensity modulation is formed between blue phase and isotropic phase of liquid crystal cell, where the blue phase liquid crystal selectively reflects circular polarization light due to the Bragg reflection, resulting in a circularly polarization-dependent optical vortex. The proposed method can be applied to any other diffractive optical elements.

Fast Hologram Pattern Generation by Adaptive Point-Spread Spherical Wave Synthesis

We propose an adaptive point-spread spherical wave synthesis method based on the point-source hologram technique for fast hologram pattern generation. The calculation time of the hologram generation is reduced by decreasing the number of reconstructed point sources composing an object. A larger point source is reconstructed in the area where an object can be partially expressed by low resolution. The point-spread is adjusted corresponding to the spatial frequency of an object. The effectiveness of the proposed method is confirmed by a computer simulation using two-dimensional images.

Simultaneous holographic imaging and light-scattering pattern measurement of individual microparticles.

This work combines digital holography with spatial filtering at two wavelengths to record the hologram and light-scattering pattern for a single particle using a color sensor. Particles 30-100 μm in size and with various shapes are considered. The results demonstrate the ability to unambiguously associate a complicated scattering pattern with the particle size, shape, and orientation.

Development of an X-ray fluorescence holographic measurement system for protein crystals.

Experimental procedure and setup for obtaining X-ray fluorescence hologram of crystalline metalloprotein samples are described. Human hemoglobin, an α2β2 tetrameric metalloprotein containing the Fe(II) heme active-site in each chain, was chosen for this study because of its wealth of crystallographic data. A cold gas flow system was introduced to reduce X-ray radiation damage of protein crystals that are usually fragile and susceptible to damage. A χ-stage was installed to rotate the sample while avoiding intersection between the X-ray beam and the sample loop or holder, which is needed for supporting fragile protein crystals. Huge hemoglobin crystals (with a maximum size of 8 × 6 × 3 mm(3)) were prepared and used to keep the footprint of the incident X-ray beam smaller than the sample size during the entire course of the measurement with the incident angle of 0°-70°. Under these experimental and data acquisition conditions, we achieved the first observation of the X-ray fluorescence hologram pattern from the protein crystals with minimal radiation damage, opening up a new and potential method for investigating the stereochemistry of the metal active-sites in biomacromolecules.

Integral imaging-based large-scale full-color 3-D display of holographic data by using a commercial LCD panel.

We propose a new type of integral imaging-based large-scale full-color three-dimensional (3-D) display of holographic data based on direct ray-optical conversion of holographic data into elemental images (EIs). In the proposed system, a 3-D scene is modeled as a collection of depth-sliced object images (DOIs), and three-color hologram patterns for that scene are generated by interfering each color DOI with a reference beam, and summing them all based on Fresnel convolution integrals. From these hologram patterns, full-color DOIs are reconstructed, and converted into EIs using a ray mapping-based direct pickup process. These EIs are then optically reconstructed to be a full-color 3-D scene with perspectives on the depth-priority integral imaging (DPII)-based 3-D display system employing a large-scale LCD panel. Experiments with a test video confirm the feasibility of the proposed system in the practical application fields of large-scale holographic 3-D displays.

Sampling and error analysis of radial symmetric interpolation for fast hologram generation.

In this paper, we present a fast hologram pattern generation method by radial symmetric interpolation, which exploits concentric redundancy of a point hologram pattern to reduce computational complexity in hologram pattern calculation, and analyze the quality degradation sources in the proposed method. Compared to the analytic method in which phase and amplitude information is directly calculated from a wave equation, in our method a Fresnel zone plate is periodically sampled along a diagonal line and the wave information of a point hologram is calculated by linear interpolation. During these sampling and interpolation processes, the wave information can be modified from the original signal and the reconstruction quality can be degraded compared to the analytic pattern calculation method. The effects of sampling and linear interpolation are investigated in spatial and frequency domains.

Three-directional motion-compensation mask-based novel look-up table on graphics processing units for video-rate generation of digital holographic videos of three-dimensional scenes.

A three-directional motion-compensation mask-based novel look-up table method is proposed and implemented on graphics processing units (GPUs) for video-rate generation of digital holographic videos of three-dimensional (3D) scenes. Since the proposed method is designed to be well matched with the software and memory structures of GPUs, the number of compute-unified-device-architecture kernel function calls can be significantly reduced. This results in a great increase of the computational speed of the proposed method, allowing video-rate generation of the computer-generated hologram (CGH) patterns of 3D scenes. Experimental results reveal that the proposed method can generate 39.8 frames of Fresnel CGH patterns with 1920×1080 pixels per second for the test 3D video scenario with 12,088 object points on dual GPU boards of NVIDIA GTX TITANs, and they confirm the feasibility of the proposed method in the practical application fields of electroholographic 3D displays.

Color image generation for screen-scanning holographic display

Horizontally scanning holography using a microelectromechanical system spatial light modulator (MEMS-SLM) can provide reconstructed images with an enlarged screen size and an increased viewing zone angle. Herein, we propose techniques to enable color image generation for a screen-scanning display system employing a single MEMS-SLM. Higher-order diffraction components generated by the MEMS-SLM for R, G, and B laser lights were coupled by providing proper illumination angles on the MEMS-SLM for each color. An error diffusion technique to binarize the hologram patterns was developed, in which the error diffusion directions were determined for each color. Color reconstructed images with a screen size of 6.2 in. and a viewing zone angle of 10.2° were generated at a frame rate of 30 Hz.

Helicity multiplexed broadband metasurface holograms.

Metasurfaces are engineered interfaces that contain a thin layer of plasmonic or dielectric nanostructures capable of manipulating light in a desirable manner. Advances in metasurfaces have led to various practical applications ranging from lensing to holography. Metasurface holograms that can be switched by the polarization state of incident light have been demonstrated for achieving polarization multiplexed functionalities. However, practical application of these devices has been limited by their capability for achieving high efficiency and high image quality. Here we experimentally demonstrate a helicity multiplexed metasurface hologram with high efficiency and good image fidelity over a broad range of frequencies. The metasurface hologram features the combination of two sets of hologram patterns operating with opposite incident helicities. Two symmetrically distributed off-axis images are interchangeable by controlling the helicity of the input light. The demonstrated helicity multiplexed metasurface hologram with its high performance opens avenues for future applications with functionality switchable optical devices.

Table screen 360-degree holographic display using circular viewing-zone scanning.

A table screen 360-degree holographic display is proposed, with an increased screen size, having an expanded viewing zone over all horizontal directions around the table screen. It consists of a microelectromechanical systems spatial light modulator (MEMS SLM), a magnifying imaging system, and a rotating screen. The MEMS SLM generates hologram patterns at a high frame rate, the magnifying imaging system increases the screen of the MEMS SLM, and the reduced viewing zones are scanned circularly by the rotating screen. The viewing zones are localized to practically realize wavefront reconstruction. An experimental system has been constructed. The generation of 360-degree three-dimensional (3D) images was achieved by scanning 800 reduced and localized viewing zones circularly. The table screen had a diameter of 100 mm, and the frame rate of 3D image generation was 28.4 Hz.

전주기법 홀로그램이 부가된 금속패턴 붙박이 도어 제작

I developed a high-quality metal door with a hologram-pattern design using a high-speed electroforming process. In this study, the major processes were master production, conducting grant, nickel-sulfamate acid electroforming, ablation treatment, and final dressing. The processing system was provided with a nickel sulfamate pole, and a rotary-pole PP-plating jig in a circular tank. This approach could reduce defects and errors, as much as possible, by its use of a hologram pattern to create the master of a metal door. The thin-sheet metal-creation process for the door built-in metal pattern using electroforming with hologram was successful.

A Magneto-Optical Spatial Light Modulator Driven by Spin Transfer Switching for 3D Holography Applications

We have successfully fabricated a basic magneto -optical spatial light modulator (MO-SLM) device driven by spin-transfer-switching (STS), which we call Spin-SLM technology. The SLM device is comprised of a one dimensional ten-pixel light modulation array (1 $\times$ 10 pixels) with a fine pitch of 1 $\mu{\hbox{m}}$ . The light modulation pixels were composed of Gd-Fe based giant magneto resistance (GMR) devices, with a free layer of Gd-Fe, an Ag spacer and a Co-Fe/Tb-Fe-Co pinned layer. The GMR devices were sandwiched by a Cu bottom and Indium zinc oxide top electrodes in order to inject current perpendicular to the film plane for switching. Incident light penetrating the transparent top electrode can be modulated due to its magneto-optic Kerr effect with the Gd-Fe free layer. The fabricated device cell size is ${\hbox{220}}\times {\hbox{300}} {\hbox{nm}}^{2}$ . We confirmed successful switching of the individual free layers, which was controlled by STS. We have also fabricated magnetic hologram patterns with the same magnetic materials used in the light modulation layer of the Spin-SLM device in order to determine its feasibility in display applications. The pixel pitch of the pattern was one micron and a reconstructed image by laser light was successfully observed with a wide viewing zone angle as 38 deg, which is nearly the same value expected from calculations. Although these patterns do not have an electrode to switch the magnetization direction, we confirmed the potential of Spin-SLM technology as a display device for 3D holography applications.

Generation of terahertz vector beams with a concentric ring metal grating and photo-generated carriers.

A scheme for vector terahertz (THz) beam generation is proposed. A subwavelength metal grating is utilized to adjust the polarization of the THz radiation. The amplitude and phase distributions of the THz beam are dynamically regulated by a THz computer-generated hologram (CGH) pattern of the photo-generated carriers. A radially polarized THz beam and a vector THz vortex beam with a topological charge of 1 are generated to demonstrate the validity and the effectiveness of the proposed scheme. Experimental results correspond to the theoretical simulations well. Moreover, the proposed method is applicative for a broadband THz radiation. These results could be applied in the THz sensing, THz imaging, and THz communication in the future.

Colorization of Magnetic Hologram Images With Optical Space Division Method

We have developed magneto-optic spatial light modulators (MOSLMs) with submicrometer-size magnetic pixels for wide-viewing-angle holographic displays (3-D-MOSLM) that are driven by the thermomagnetic recording. The holographic images were reconstructed by the magnetic hologram pattern on the MOSLM. In this paper, we have studied colorization of reconstruction images of the MOSLMs using optical space division method. This method used some 3-D-MOSLMs to represent intermediate colors. The magnetic films were polycrystalline bismuth, dysprosium, and aluminum substituted yttrium iron garnet (BiDyYFeAlG) films with perpendicular magnetization. The thickness of BiDyYFeAlG films was designed for each wavelength. The MOSLM represented (3-D) images with intermediate colors that were synthesized 3-D images with red and green colors. In addition, tones of intermediate colors were represented by controlling intensity of each reference light. These results demonstrated that 3-D-MOSLMs have promise for full-colorized holographic 3-D displays.

Fast one-step calculation of holographic videos of three-dimensional scenes by combined use of baseline and depth-compensating principal fringe patterns.

As a new approach for rapid generation of holographic videos, a so-called compressed novel-look-up-table(C-NLUT), which is composed of only two principal fringe patterns (PFPs) of baseline and depth-compensating PFPs (B-PFP, DC-PFP), is proposed. Here, the hologram pattern for a 3-D video frame are generated by calculating the fringe patterns for all depth layers only by using the B-PFP, and then transforming them into those for their depth layers by being multiplied with corresponding DC-PFPs. With this one-step calculation process, the computational speed (CS) of the proposed method can be greatly enhanced. Experimental results show that the CS of the proposed method has been improved by 30.2% on the average compared to that of the conventional method. Furthermore, the average calculation time of a new hybrid MC/C-NLUT method, in which both of motion-compensation (MC) and one-step calculation schemes are employed, has been reduced by 99.7%, 65.4%, 60.2% and 30.2%, respectively compared to each of the conventional ray-tracing, LUT, NLUT, and MC-NLUT methods. In addition, the memory size of the proposed method has been also reduced by 82 × 10(6)-fold and 128-fold compared to those of the conventional LUT and NLUT methods, respectively.

Improvement of gray-scale representation of horizontally scanning holographic display using error diffusion.

Horizontally scanning holography can enlarge both screen size and viewing zone angle. A microelectromechanical-system spatial light modulator, which can generate only binary images, is used to generate hologram patterns. Thus, techniques to improve gray-scale representation in reconstructed images should be developed. In this study, the error diffusion technique was used for the binarization of holograms. When the Floyd-Steinberg error diffusion coefficients were used, gray-scale representation was improved. However, the linearity in the gray-scale representation was not satisfactory. We proposed the use of a correction table and showed that the linearity was greatly improved.

One-eighth look-up table method for effectively generating computer-generated hologram patterns

To generate ideal digital holograms, a computer-generated hologram (CGH) has been regarded as a solution. However, it has an unavoidable problem in that the computational burden for generating CGH is very large. Recently, many studies have been conducted to investigate different solutions in order to reduce the computational complexity of CGH by using particular methods such as look-up tables (LUTs) and parallel processing. Each method has a positive effectiveness about reducing computational time for generating CGH. However, it appears to be difficult to apply both methods simultaneously because of heavy memory consumption of the LUT technique. Therefore, we proposed a one-eighth LUT method where the memory usage of the LUT is reduced, making it possible to simultaneously apply both of the fast computing methods for the computation of CGH. With the one-eighth LUT method, only one-eighth of the zone plates were stored in the LUT. All of the zone plates were accessed by indexing method. Through this method, we significantly reduced memory usage of LUT. Also, we confirmed the feasibility of reducing the computational time of the CGH by using general-purpose graphic processing units while reducing the memory usage.