Hole Pattern Research Articles

Plasmonic lithography fast imaging model based on least square fitting for periodic patterns

As a new and alternative lithography technology, plasmonic lithography can break through the diffraction limit of traditional lithography by exciting the surface plasmon polaritons to make the evanescent wave at the mask participate in imaging. Plasmonic lithography is capable of fabricating deep subwavelength structures for nanophotonics, metasurfaces, and various other applications, and it is expected to be applied to integrated circuit manufacturing. The photoresist aerial image distribution of different mask patterns can be calculated by establishing an imaging model, which is the basis for understanding and further optimizing imaging. Based on the idea of machine learning and least square fitting, a fast imaging model for plasmonic lithography is established, including a one-dimensional line/space periodic pattern and a two-dimensional square hole pattern, which can be used as a supplement to the previous model developed by Ding et al. [Opt. Express 31, 192 (2023)OPEXFF1094-408710.1364/OE.476825]. Compared with the rigorous numerical method, the fast imaging model can greatly improve the calculation speed with high accuracy. Under the same hardware conditions, the calculation speed of the 1D fast imaging model is improved by two orders of magnitude, and the 2D fast imaging model is improved by about 25 times, which creates conditions for the development of computational lithography technology.

Dry Transfer of van der Waals Junctions of Two-Dimensional Materials onto Patterned Substrates Using Plasticized Poly(vinyl chloride)/Kamaboko-Shaped Polydimethylsiloxane.

Two-dimensional (2D) materials can be transferred onto substrates with various surface structures, opening up multiple functions and applications for 2D materials in the form of suspended membranes. In this paper, we present a method for transferring exfoliated 2D crystal flakes from SiO2 substrates onto patterned substrates using a poly(vinyl chloride) (PVC) layer mounted on a polydimethylsiloxane (PDMS) stamp structure. 2D crystal flakes can be transferred onto various patterned structures such as grooves, round holes, and periodic hole or groove patterns. Our method can also be used to fabricate suspended van der Waals (vdW) heterostructures by assembling 2D crystal flakes on the PVC/PDMS stamp and then transferring them onto patterned substrates. The adhesiveness and curvature of the PVC/PDMS stamp were tuned, and a high successful transfer rate was realized due to the use of kamaboko-shaped (semicylindrical) PDMS and the addition of an appropriate amount of a high-viscosity plasticizer to the PVC layer. Taking advantage of this method, we demonstrate the facile fabrication, simply by transferring a vdW heterostructure onto an Au-coated groove substrate, of a suspended vdW field-effect transistor device with the carrier density tuned using ionic gating. This method enables the transfer of 2D crystal flakes and vdW heterostructures onto various patterned substrates, and hence it should help to advance suspended 2D materials research.

A New Two-Phase Design Process for a Compliant Mechanism Gripper

The structural design of the components with high accuracy and controllable motion is the focus of precision industries. As a result, researchers found that components created via compliant mechanisms were much preferable. Monolithic structures known as compliant mechanisms allow motion to be achieved without the need of traditional joints. The compliant mechanisms make it easier to build microscale devices because they do not have hard junctions. In this study, a novel two-phase design methodology for compliant mechanism forceps is proposed. In order to eliminate high-stress areas, forceps are often constructed as a distributed compliant mechanism. To offer a distributed planar design, topological optimization is introduced with new approach. Design domain introduced with pattern of holes restricts the single point contact formation and large area formation which yield distributed compliant mechanism. The parametrization technique is implemented to convert the conceptual design to working design. The design of compliant forceps is assessed using finite element analysis (FEA) based on structural considerations. Finally, a handle-equipped microgripper prototype has been developed. Experimental verification demonstrates the gripper's performance and variation is less than 3% with numerical results. Integerated force sensor measure the gripping force and compared the reaction force estimated through FEA.

An experimental study on the influence of nozzle hole numbers and patterns of a passive pre-chamber spark ignition system

Pre-chamber spark ignition system enhances the combustion stability and efficiency of lean burn engines. Pre-chamber spark ignition system performance directly relies on the characteristics of the turbulent flame jet, which are governed by the pre-chamber geometrical parameters and nozzle hole configurations. Based on the existing literatures, limited research on nozzle hole numbers and patterns is noted with passive pre-chamber, and thus, the impact of these nozzle hole configurations on the combustion and flame development characteristics for hydrogen-methane-air mixtures is investigated in a constant volume combustion chamber. In the current study, single-layer nozzle hole configurations with three, four, six, and eight nozzle holes and double-layer nozzle hole configurations with six and eight nozzle holes are designed and tested in an optically accessible combustion chamber under various equivalence ratio conditions. The results indicated that the combustion characteristics deteriorated with an increase in nozzle holes, except with the single-layer four nozzle hole configuration. Compared to the single-layer eight nozzle hole configuration, the ignition delay and combustion duration for hydrogen-methane-air mixtures with single-layer four nozzle hole configuration was reduced by 31.9% and 30.7% under lean conditions. A reduction in flame jet penetration length, area and velocity and increased adjacent flame jet interaction was noticed for the single-layer configuration with more nozzle holes, and thus, a different nozzle hole pattern was studied in the current study. The double-layer configurations with more nozzle holes showed better combustion and flame development characteristics than single-layer configurations due to their unique flame structure, uniform and faster flame jet distribution, and reduced adjacent flame jet interaction. The ignition delay and combustion duration for hydrogen-methane-air mixtures with the double layer eight nozzle hole configuration were reduced by 30.5% and 40.7% compared to the single-layer eight nozzle hole configuration.

Dynamic Modeling and Vibration Characteristic Analysis of Fiber Woven Composite Shaft–Disk Rotor with Weight-Reducing Holes

In order to achieve the goal of a lightweight shaft–disk rotor, this paper applies the fiber woven composite material to the disk structure, and at the same time considers the design of the weight-reducing holes on the porous disk. It introduces the domain decomposition and coordinate mapping technology for this, and then establishes the dynamics model of the fiber woven composite material shaft–disk rotor. The model is based on the differential quadrature finite element method, which is suitable for fiber woven composite rotors with arbitrary complex hole patterns. The validity of the model is verified by comparing the results with the literature, finite element simulation, and experiments, and the mechanism of the influence of the material parameters and pore parameters on the vibration characteristics of the system is investigated, which provides the data support and theoretical basis for the analysis of the dynamics of the fiber woven composite rotor.

Influence of Dilution and Effusion Flows in Generating Variable Inlet Profiles for a High-Pressure Turbine

Abstract The elevated flow temperatures and pressures exiting gas turbine combustors affect the efficiency and durability of the high-pressure turbine stage. Understanding the effects that result from the upstream dilution and effusion flow interaction in creating the combustor exit profiles is important to advancing gas turbines. Understanding how common combustor features, such as dilution jets and effusion cooling, interact based on computational predictions guided the design of a non-reacting profile simulator capable of producing a wide range of non-uniform temperature profiles representative of those entering high-pressure turbines. The mechanical design of a new simulator device, which will be experimentally tested in the future, is presented in this paper along with computational predictions of flow and thermal fields. The simulator was designed for modular installation into the Steady Thermal Aero Research Turbine (START), which is a continuous-duration, steady-state turbine facility that houses a single-stage test turbine. Features of the simulator included interchangeable liner panels with multiple rows of dilution jets and wall effusion cooling to study various hole diameters and patterns. The dilution jets generate elevated turbulence intensities and tailor the temperature profiles in the radial and circumferential directions. The air mass flow distribution and source flow temperatures are independently controlled. To aid in the simulator design, computational fluid dynamics (CFD) simulations using Reynolds-averaged Navier–Stokes modeling were conducted with a two-level Design of Experiments (DOE) approach to determine a number of engine-representative target profiles with temperature shapes that are mid-radius peaked, outer-diameter peaked, inner-diameter peaked, and uniform. A sensitivity analysis of the CFD DOE results determined which factors significantly affected the profile shape so that the target profiles could be produced. The analysis indicated that the main contributor to the temperature profile shape at near-wall vane radial span locations of 0–15% and 85–100% was the injection temperature of the effusion flow. The main contributor at radial span locations of 15–40% and 60–85% was the injection temperature of the third-row dilution jets, and at the mid-radius location of 40–60% vane radial span, the main contributor was the diameter of the first-row dilution holes.

Spin-preserving chiral mirror based on a pattern of rotated elliptical holes in thin monolithic all-dielectric photonic crystal slabs

Spin-preserving chiral mirror based on a pattern of rotated elliptical holes in thin monolithic all-dielectric photonic crystal slabs

Numerical study of transpiration cooling at different outlet angles and hole pattern

The effects of transpiration cooling depends on the distribution of micropores in porous materials. The work simplifies the porous medium to a micro-scale pore plate structure that is densely organized, based on the idea of the capillary bundle model. The effects of hole pattern and hole outlet angle on transpiration cooling are investigated using numerical simulation. It is discovered that the hole outlet angle mostly affects the homogeneity of temperature distribution and has minimal effect on the surface cooling efficiency. The temperature uniformity index dropped by 35.9% yet the surface cooling efficiency only declined by 1.1% when the outlet angle was lowered from 45° to −45°. Furthermore, the temperature uniformity and cooling efficiency are directly affected by the hole pattern. When the long axis of the elliptical hole is parallel to the mainstream, it can achieve the best temperature uniformity; however, when the long axis is perpendicular to the mainstream direction, it can achieve higher cooling efficiency. Third, the material’s permeability will be decreased to varying degrees depending on the hole pattern and hole outlet angle. The results have important reference significance for the design of porous materials used for transpiration cooling.

Development of A Hydrogen Micro Gas Turbine Combustor: Nox Emissions and Secondary Air Injection

Abstract In the scope of the H2mGT project, a micro gas turbine (mGT) burner with 100% hydrogen firing is developed. The project is a collaboration between TUB and the manufacturer Euro-K GmbH. It consists of three phases: 1. Atmospheric pressure tests with a fused silica combustion chamber; 2. Atmospheric pressure tests with counterflow-cooled steel flame tube and secondary air injection; 3. Validation of the burner in the mGT at elevated pressure levels. The current study will present the results of Phase 2. The hydrogen burner used in the project is based on a swirlstabilized burner of TUB and was scaled to 36 kW thermal power at atmospheric conditions. The burner design features a variable swirl intensity, a movable central fuel lance and pilot nozzles at the front plate. The burners steel flame tube is exchangeable, which allows the evaluation of different dilution hole patterns and, thus, the variation of the primary and secondary air. The study presents temperature, pressure, and emission measurements. It is found that the flame can be operated over a large range of equivalence ratios and preheating temperatures up to 500°C. The NOx emissions are mainly influenced by the local equivalence ratio, which can be controlled by the fuel mass flow or the dilution hole pattern in the flame tube. Furthermore, the results show a decrease of NOx when the power density is increased at constant equivalence ratios, and a rise of NOx during the fuel transition from natural gas to hydrogen.

In situ Low-Energy Electron Microscopy of Chemical Waves on a Composite V-oxide/Rh(110) Surface.

Chemical wave patterns and V-oxide redistribution in catalytic methanol oxidation on a VOx/Rh(110) surface have been investigated in the 10-4 mbar range with low-energy electron microscopy (LEEM) and micro spot low-energy electron diffraction (micro-LEED) as in situ methods. V coverages of θV=0.2 and 0.4 MLE (monolayer equivalents) were studied. Pulses display a c(2×2) pattern in the reduced part and (1×2) and c(2×8) structures in the oxidized part of the surface. At θV=0.4 MLE (1×2)/(1×4) patterns with streaks along the [001]-direction at the 1/8 positions are present on the oxidized part of the surface. This phase can be assigned to V-oxide. On a tentative basis, an excitation mechanism for pulses is presented, Annealing the surface to 990 K under reaction conditions results in a macroscopic hole pattern in which holes of low VOx coverage are surrounded by a V-oxide layer. Chemical waves propagate inside the holes as well as on the VOx covered parts of the surface. The results demonstrate for the first time that also in supported oxidic overlayers selforganization processes can take place leading to chemical waves and a large scale redistribution of the oxide.

Optimization of the Al Composition of the p‐AlGaN Electron Blocking Layer in GaInN/GaN Multiquantum‐Shell Nanowire LEDs

The aim is to develop highly efficient GaInN/GaN nanowire (NW)‐based light‐emitting diodes (LEDs), which are composed of GaN NWs and multiquantum shell (MQS) active regions. These regions incorporate the polar c‐plane, nonpolar r‐plane, and semipolar m‐plane. A challenge with MQS‐LEDs is that the current path through the c‐plane MQS tends to dominate under low‐current injection conditions. Given that the MQS on the c‐plane is very defective, this injection current is mainly subjected to nonradiative recombination. Therefore, this study explores various optimizations of the p‐AlGaN electron blocking layers (EBLs) to minimize the current injection into the MQS in the c‐plane region. The samples are subsequently grown using a specific process. This involves n‐GaN NWs, GaInN/GaN‐based quantum shells, p‐AlGaN EBLs with different Al compositions, and p‐GaN shells. All these are developed by metal–organic vapor phase epitaxy on an n‐GaN template featuring a SiO2 hole pattern. NW LEDs are fabricated and subsequently their device characteristics are investigated. Under low‐current injection, the sample with a lower Al composition exhibits higher luminescence intensity. However, this trend reverses when the injection current increases. The findings suggest that AI composition and thickness in the p‐AlGaN EBL significantly affect the output power and the emission wavelength.

Experimental and numerical investigations on film cooling performance of converging slot holes in plate and turbine conditions

Based on the heat-mass transfer analogy, the Pressure Sensitive Paint (PSP) technique was used to explore the film cooling characteristics of converging slot holes on the plate model and the actual turbine endwall model conditions. Meanwhile, the numerical calculation was also adopted to pursue the flow field details. The width of the converging slot hole exit is a key geometry affecting cooling performance. On the plate model condition, three widths of exit slot Lw (1.7d, 2.3d, 2.9d) were chosen to obtain the optimal exit width. The case with Lw = 2.3d obtained the highest level of adiabatic effectiveness from spanwise and streamwise views. This case operated as a two-dimensional slot and produced a more uniform cooling jet film relative to other cases. Nevertheless, the cooling performance decreased significantly as the converging slot hole width increased to Lw = 2.9d. Then the cooling performance of three patterns of film holes was further investigated in the turbine endwall. Laid-back fan-shaped holes and converging slot holes could improve the film cooling performance effectively compared to the cylindrical holes. Converging slot holes with Lw = 2.3d improved the uniformity of the cooling jet outflow through rows of upstream film holes, and also effectively avoided the phenomenon of coolant blowing away or high-temperature gas entering the film hole, resulting in high film cooling effectiveness performance. Compared to cylindrical holes, the area-averaged adiabatic effectiveness was increased by 216.5 % for the endwall with cylindrical holes with the momentum ratio I = 0.25. Overall, converging slot holes improved cooling performance among all studied film hole configurations.

Nanoimprint Lithography for Next-Generation Carbon Nanotube-Based Devices.

This research reports the development of 3D carbon nanostructures that can provide unique capabilities for manufacturing carbon nanotube (CNT) electronic components, electrochemical probes, biosensors, and tissue scaffolds. The shaped CNT arrays were grown on patterned catalytic substrate by chemical vapor deposition (CVD) method. The new fabrication process for catalyst patterning based on combination of nanoimprint lithography (NIL), magnetron sputtering, and reactive etching techniques was studied. The optimal process parameters for each technique were evaluated. The catalyst was made by deposition of Fe and Co nanoparticles over an alumina support layer on a Si/SiO2 substrate. The metal particles were deposited using direct current (DC) magnetron sputtering technique, with a particle ranging from 6 nm to 12 nm and density from 70 to 1000 particles/micron. The Alumina layer was deposited by radio frequency (RF) and reactive pulsed DC sputtering, and the effect of sputtering parameters on surface roughness was studied. The pattern was developed by thermal NIL using Si master-molds with PMMA and NRX1025 polymers as thermal resists. Catalyst patterns of lines, dots, and holes ranging from 70 nm to 500 nm were produced and characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Vertically aligned CNTs were successfully grown on patterned catalyst and their quality was evaluated by SEM and micro-Raman. The results confirm that the new fabrication process has the ability to control the size and shape of CNT arrays with superior quality.

Shape Programming of Porous Bilayer Hydrogel Structures

Abstract Shape-programmable materials have garnered significant attention for their ability to morph into complex three-dimensional (3D) configurations under external stimuli, with critical applications in the fields of biomedical engineering, soft robotics, and sensing technologies. A current challenge lies in determining the geometric parameters of the initial two-dimensional (2D) structure and the intensity of the external stimulus required to achieve a target 3D shape. In this work, we introduce a novel inverse design strategy based on hole pattern engineering. Utilizing a temperature-sensitive bilayer hydrogel with differing coefficients of thermal expansion in each layer, we achieve controlled bending deformations by varying the porosity distribution in one of the layers. Drawing on the Timoshenko theory on bimetallic beam, we establish a quantitative relationship between porosity and curvature, allowing for the hole distribution of the initial structure to be tailored to the desired curvature. We demonstrate the efficacy of our inverse design approach with several prototypical 3D structures, including variable-curvature strip and ellipsoidal surface, validated through finite element simulations and experimental trials. This strategy paves the way for advanced fabrication techniques in developing smart materials and devices with programmable shapes.

Optimizing Structural Patterns for 3D Electrodes in Lithium-Ion Batteries for Enhanced Fast-Charging Capability and Reduced Lithium Plating

The most common pattern types for anode structuring, in particular the line, grid, and hexagonal-arranged hole pattern were evaluated in a comparable setup in full-cells and symmetrical cells. The cells with structured electrodes were compared to reference cells with unstructured anodes of similar areal capacity (4.3 mAh cm−2) and the onset of lithium plating during fast-charging was determined in situ by differential voltage analysis of the voltage relaxation and ex situ by post-mortem analysis. Furthermore, electrochemical impedance spectroscopy measurements on symmetrical cells were used to determine the ionic resistance of structured and unstructured electrodes of similar areal capacity. All cells with structured electrodes showed lower ionic resistances and an onset of lithium plating shifted to higher C-rates compared to cells with unstructured electrodes. The structure patterns with capillary structures, i.e., lines and grids, showed significant reduced lithium plating during fast-charging and a higher rate capability compared to reference cells with unstructured electrodes and cells with hole structured electrodes. The continuous rewetting of the electrode with liquid electrolyte by capillary forces and the reduced ionic resistance of the 3D electrode are identified as key factors in improving overall battery performance. The data of the studied cells were used to calculate the resulting energy and power densities of prospective commercial pouch cells and potential pitfalls in the comparison to cells with unstructured electrodes were identified.

Dermoscopy of Actinic Lichen Planus in Skin of Color.

Actinic Lichen Planus (ALP) is a rare photosensitive variant of lichen planus. Four subtypes can be distinguished: pigmented, annular (AALP), plaque-like and dyschromic ALP. This is a retrospective; descriptive and analytical study investigating the dermoscopic patterns of different subtypes of ALP in skin of color. Sixteen adult patients were included in this study; the majority of them were young females, while five patients with the pigmented subtype of ALP were more than 50 years old. This subtype was more prevalent in patients with phototype IV. AALP was described in men with a very dark phototype.In pigmented melasma-like ALP, dermoscopy showed an annular granular pattern, white reticular and circular Wickham striae (WS) with hypopigmentation lacking skin creases, dots inside circles and an eccentric pigmentation on circles. In ALP, annular, circular WS; and perifollicular white halos with follicular plugs were described. The black hole pattern with dotted vessels was seen in the dyschromic ALP. White-yellow-bluish WS were noticed in plaque-type ALP with circumferential radial lines at the periphery. This descriptive study of dermoscopic patterns of various subtypes of ALP in skin of color highlighted new dermoscopic descriptions that vary according to the clinical variant or the morphology; lesions distribution; and phototype. Also, many epidemiological differences were found between our results and the literature concerning the older age of onset in melasma-like pigmented ALP, and the male predominance in annular ALP.

Plasma-based etching approach for GEM detector microfabrication at FBK for X-ray polarimetry in space

Gas Electron Multiplier (GEM) detectors are crucial for enabling high-resolution X-ray polarization of astrophysical sources when coupled to custom pixel readout ASIC in Gas Pixel Detectors (GPD), as in the Imaging X-ray Polarimetry Explorer (IXPE), the Polarlight cubesat pathfinder and the PFA telescope onboard the future large enhanced X-ray Timing and Polarimetry (eXTP) Chinese mission. The R&D efforts of the IXPE collaboration have resulted in mature GPD technology. However, limitations in the classical wet-etch or laser-drilled fabrication process of GEMs motivated our exploration of alternative methods. This work focuses on investigating a plasma-based etching approach for fabricating GEM patterns at Fondazione Bruno Kessler (FBK). The objective is to improve the aspect ratio of the GEM holes, to mitigate the charging of the GEM dielectric which generates rate-dependent gain changes. Unlike the traditional wet-etch process, Reactive Ion Etching (RIE) enables more vertical etching profiles and thus better aspect ratios. Moreover, the RIE process promises to overcome non-uniformities in the GEM hole patterns which are believed to cause systemic effects in the azimuthal response of GPDs equipped with either laser-drilled or wet-etch GEMs. We present a GEM geometry with 20 μm in diameter and 50 μm pitch, accompanied by extensive characterization (SEM and PFIB) of the structural features and aspect ratios. The collaboration with INFN Pisa and Turin enabled us to compare the electrical properties of these detectors and test their performance in their use as electron multipliers in GPDs. Although this R&D work is in its initial stages, it holds promise for enhancing the sensitivity of the IXPE mission in X-ray polarimetry measurements through GEM pattern with more vertical hole profiles. The outcomes of this study have the potential to advance the current technological platforms and improve the capabilities of future space-based X-ray polarimetry missions.

Directed Self-Assembly of Cylinder-Forming Block Copolymers Using Pillar Topographic Patterns.

We conducted a computational study on the self-assembly behavior of cylinder-forming block copolymers, directed by a guide pattern of hexagonally or tetragonally arrayed pillars, using mesoscale density functional theory simulations. By adjusting the spacing (Lp) and diameter (D) of the pillars in relation to the intrinsic cylinder-to-cylinder distance (L2) of the cylinder-forming block copolymer, we investigated the efficiency of multiple-replicating cylinders, generated by the block copolymer, through the pillar-directed self-assembly process. The simulations demonstrated that at specific values of normalized parameters L˜2=L2/Lp and D˜=D/Lp coupled with suitable surface fields, triple and quadruple replications are achievable with a hexagonally arrayed pillar pattern, while only double replication is attainable with a tetragonally arrayed pillar pattern. This work, offering an extensive structure map encompassing a wide range of possible parameter spaces, including L˜2 and D˜, serves as a valuable guide for designing the contact hole patterning essential in nanoelectronics applications.

Experimental study on resin pin-reinforced marine sandwich composites under quasi-static indentation load

This study aims to experimentally examine the indentation behaviour of marine sandwich composites with pin-reinforced polyvinyl chloride foam core and E-glass face sheets. The effects of indenter diameter, resin pin diameter, and arrangement on force-displacement, maximum contact force, and absorbed energy values of sandwich panels were evaluated by the indentation tests. Throughout the experiments, the contact forces increased as the pin diameter increased. The contact forces reduced as the distance between pin diameters increased. Additionally, the values of absorbed energy increased as the diameters of the resin pin and indenter increased. Placing the pins more closely together additionally allows the material to absorb more energy in the event of indentation. A visual inspection took place on the post-indentation cross-sections of the sandwich specimens to detect any damage modes. Damage modes varied depending on the size of the indenter and the hole pattern in the foam core.

Experimental investigation of pier scour depth and its scour hole pattern for different shapes

Local scour, a complex phenomenon in river flows around piers with movable beds, can damage bridge piers during high floods. Predicting scour depth accurately is vital for safety and economic reasons, especially for large bridges. This study using hydraulic flume laboratory experiments compared diamond, square, and elliptical pier models of different sizes under steady clear-water conditions considering different flow rates and discharge levels to identify the most efficient shape with less local scour. Local scour, a complex phenomenon in three-dimensional flow around piers in rivers with movable beds, can lead to detrimental effects on bridge piers due to high flood velocities. Accurate prediction of scour depth is crucial for economic and safety reasons, especially for large bridges with complex piers. Hydraulic engineers are keen on forecasting the equilibrium scour depth. To achieve this, laboratory testing compared diamond, square, and elliptical pier models under steady clear-water conditions to identify the most efficient pier shape with less local scour. This research provides valuable insights for optimizing pier design to enhance bridge stability and resilience against scour-induced risks. A variety of configurations, including different sizes and shapes of piers were experimented with in the flume using diamond, square, and elliptical shapes. The test results showed that the local scour depth around elliptical piers was around 29.16% less, and around diamond piers, it was approximately 16.05% less compared to the scour depth observed around square piers with the same dimensions. The researchers also observed distinct patterns of scouring around different pier shapes. Specifically, the square-shaped piers displayed the highest level of scouring depth, that is, 48 mm, followed by the diamond-shaped pier which experienced a scouring depth of 48 mm while the elliptical-shaped piers experienced the least amount of scouring depth, that is, 34 mm. The test results also demonstrated that pier size significantly influences scouring, with an increase in pier size from 3 × 3 cm2 to 5 × 5 cm2 leading to a rise in scour depth by 26.04%. Moreover, this study findings also elucidated that an increase in flow results in an increase of in scouring depth i.e., elevating the discharge from 0.0026 cumecs to 0.0029 cumecs led to a 28.13% increase in scouring depth for the identical pier size. These findings provide valuable insights into the hydraulic behavior of various pier shapes and can aid in the optimization of bridge design and hydraulic engineering practices. The investigations further revealed that local scouring is sensitive not only to pier dimensions but also to other critical parameters, including flow rate, time of exposure, and the size of a pier.