Hip Stem Research Articles

Incidence and risk factors of intraoperative periprosthetic femoral fractures during primary total hip arthroplasty: 218,423 cases reported to the Norwegian Arthroplasty Register between 1987 and 2020.

Background and purposeIntraoperative periprosthetic femoral fractures (IPFFs) can occur during primary total hip arthroplasty (THA). We describe the incidence of IPFFs during THA in Norway and estimate potential risk factors that could be associated with IPFFPatients and methodsData from the Norwegian Arthoplasty Register (1987–2020) was used: 2,268 IPFFs from 218,423 primary THAs in 172,598 patients. The following factors were analyzed: sex, age, diagnosis, previous operation on the same hip, surgical approach, and stem fixation technique. Association of these factors with IPFF risk was assessed using multivariable Poisson regression.ResultsIPFF occurred during 2,268 operations with an incidence of 1.0% among all primary THAs. The risk of IPFF was associated with female sex (relative risk 1.8; 99% CI 1.5–2.1), age 80–90 years and age over 90 years (compared with age 60–70 years: 1.3; CI 1.0–1.6 and 2.6; CI 1.6–4.3, respectively), non-osteoarthritis diagnoses (2.2; CI 1.9–2.6), previous surgery to the same hip (1.8; CI 1.5–2.2), lateral approach (compared with the posterior approach: 1.5; CI 1.1–2.0), and cementless stem fixation (2.7; CI 2.0–3.6).InterpretationSurgeons should be aware of the factors associated with an increased risk of IPFF: female sex, age above 80 years, non-osteoarthritis diagnoses, and previous surgery to the same hip. Cemented stem fixation and posterior approach should be favored in high-risk patients, such as elderly women.

Static, fatigue and stress-shielding analysis of the use of different PEEK based materials as hip stem implants

Abstract There is a possibility that hip joints may become dysfunctional due to age, wear or some accidents, and in this case they need to be replaced with hip implants. However, after conventional hip stem implantation, the load transferred to the bone usually decreases due to the high stiffness of the metallic (most commonly Ti6Al4V, CoCr or stainless steel) hip stem implant, and as a result, mineral loss occurs in the bone which weakens. On the other hand, PEEK is an advantageous material with its low cost, ease of production, corrosion resistance and biocompatibility. More importantly, it has the potential to be a good alternative to metallic materials in load-bearing bone replacements, thanks to its mechanical properties and density close to that of the bone. In this study, hip stem implants having three different commercial PEEK materials and four different metallic main spar designs were modeled. Their behavior under static and dynamic loading conditions was analyzed according to ASTM-F2996-20 and ISO-7206-4:2010 standard test methods, and the stress-shielding effect of hip stems modeled as implanted into the femur was simulated using ANSYS commercial finite element analysis software. According to the results, it was observed that CFP based hip stem models meet the five million life time criteria and increase the stress on the femur bone by up to 57%.

Short Stem for Total Hip Arthroplasty (THA) - Overview, Patient Selection and Perspectives by Using the Metha® Hip Stem System.

Short stem hip replacement has not only gained attention but also significance over the past decades. However, there still remains uncertainty regarding the correct indications for these stems. Even companies, producing implants, have varying recommendations that are more likely based on a well-meant advice than on statistically evaluated data. Thus, it is important to evaluate the advantages and disadvantages of a short stem prosthesis. The goal of this paper is to reveal some of the existing uncertainty in this field, by analyzing the Metha® short hip stem system. This paper does not only focus on general aspects but also discusses some more specific problems, such as avascular necrosis and post-rheumatic diseases, as well as hip dysplasia and coxarthrosis. The aim is also to convey the opportunity to indicate this type of implant for elderly and obese patients as well as for femoral misalignments following post-Perthes disease, post-traumatic deformities or other malpositions of the hip.

A model-based radiostereometric analysis (RSA) randomized control trial evaluating the stability of the cementless Taperloc hip stem: the TapHip study.

Background and purposeThe Taperloc Complete hip is the successor of the Taperloc hip, aiming to increase range of motion and optimizing femoral fit with intermediate stem sizes. We evaluated whether these design changes affect fixation, and this RSA study compares 2-year migration.Patients and methodsIn this prospective, multi-arm study, 100 patients were randomized to cementless total hip arthroplasty (THA) with Taperloc Complete full profile (TCFP), Taperloc Complete reduced distal (TCRD), Taperloc full profile (TFP), or Taperloc reduced distal (TRD). Migration was measured with model-based RSA postoperatively, and after 3, 12, and 24 months.ResultsResults based on mixed-model analysis on 2-year postoperative RSA data from 74 patients showed similar subsidence (mm) in the first 3 months (mean [95% CI] TCFP 0.44 [0.20–0.69], TCRD 0.91 [0.40–1.42], TFP 0.71 [0.22–1.19], TRD 1.25 [0.58–1.91]) and stabilization afterwards. The TCFP showed statistically significantly less retroversion (°) at 2-year postoperatively compared with TFP and TCRD (mean [95% CI] TCFP: –0.13 [–0.64 to 0.38], TCRD: 0.84 [0.35–1.33], TFP: 0.56 [0.12–1.00], TRD: 0.37 [–0.35 to 1.09]).InterpretationAs expected in successful cementless THA, RSA shows stabilization after initial subsidence. Based on these results the Taperloc Complete stem is expected to have similar long-term fixation to the Taperloc stems. The reduced distal groups have larger, but statistically non-significant, initial migration compared with the TCFP group, which could be due to implantation in Dorr B, C femur types. It may be important to consider the femur shape for choosing a full profile or reduced distal stem to minimize migration.

Material Removal of Hip Stem Prosthesis Using Bio-Inspiration from Trabecular Bone

In the hip stem prostheses domain, stress shielding represents a major issue due to its potential implant loosening effect. This phenomenon occurs when the implant is much stiffer than the bone itself. A way to reduce this stiffness difference is to remove material from the implant. In addition, this solution leads to mass reduction of the implant, improving the patient quality of life. To insure the implant will withstand the loading, material must be distributed in a specific way. Bones use the same objectives of lightness and mechanical efficiency while using a minimal amount of material. In addition, these biological structures are well spread and reliable in living beings, especially in mammals and avian species. In this paper, a method bio-inspired by trabecular bone structure is proposed to remove material from parts considering their mechanical stress field. In Nature, trabecular bone is defined as a graded porous material with bone material locally oriented along the local stresses’ direction. To mimic this natural behavior, the proposed method generates local porosities bio-inspired in position, shape, size and orientation. To evaluate the proposed method performance, experimental tests were carried out on a hip prosthesis stem. Test results demonstrated that the method can be used to reduce the stiffness of the prosthesis while withstanding the applied constrains.

Is the French Paradox cementing philosophy superior to the standard cementing? A randomized controlled radiostereometric trial and comparative analysis.

AimsHighly polished stems with force-closed design have shown satisfactory clinical results despite being related to relatively high early migration. It has been suggested that the minimal thickness of cement mantles surrounding the femoral stem should be 2 mm to 4 mm to avoid aseptic loosening. The line-to-line cementing technique of the femoral stem, designed to achieve stem press-fit, challenges this opinion. We compared the migration of a highly polished stem with force-closed design by standard and line-to-line cementing to investigate whether differences in early migration of the stems occur in a clinical study.MethodsIn this single-blind, randomized controlled, clinical radiostereometric analysis (RSA) study, the migration pattern of the cemented Corail hip stem was compared between line-to-line and standard cementing in 48 arthroplasties. The primary outcome measure was femoral stem migration in terms of rotation and translation around and along with the X-, Y-, and Z- axes measured using model-based RSA at three, 12, and 24 months. A linear mixed-effects model was used for statistical analysis.ResultsResults from mixed model analyses revealed a lower mean retroversion for line-to-line (0.72° (95% confidence interval (CI) 0.38° to 1.07°; p < 0.001), but no significant differences in subsidence between the techniques (-0.15 mm (95% CI -0.53 to 0.227; p = 0.429) at 24 months. Radiolucent lines measuring < 2 mm wide were found in three and five arthroplasties cemented by the standard and line-to-line method, respectively.ConclusionThe cemented Corail stem with a force-closed design seems to settle earlier and better with the line-to-line cementing method, although for subsidence the difference was not significant. However, the lower rate of migration into retroversion may reduce the wear and cement deformation, contributing to good long-term fixation and implant survival.Cite this article: Bone Joint J 2022;104-B(1):19–26.

Subject specific finite element modelling of periprosthetic femoral fractures in different load cases

Periprosthetic femoral fractures (PFF) around total hip replacements are one of the biggest challenges for orthopaedic surgeons. To understand the risk factors and formation of these fractures, the development of a reliable finite element (FE) model incorporating bone failure is essential. Due to the anisotropic and complex hierarchical structure of bone, the mechanical behaviour under large strains is difficult to predict. In this study, a state-of-the-art subject specific FE modelling technique for bone is utilised to generate and investigate PFF. A bilinear constitutive law is applied to bone tissue in subject specific FE models of five human femurs which are virtually implanted with a straight hip stem to numerically analyse PFF. The material parameters of the models are expressed as a function of bone ash density and mapped node wise to the FE mesh. In this way the subject specific, heterogeneous structure of bone is mimicked. For material mapping of the parameters, computed tomography (CT) images of the original fresh-frozen femurs are used. Periprosthetic fractures are generated by deleting elements on the basis of a critical plastic strain failure criterion. The models are analysed under physiological and clinically relevant conditions in two different load cases re-enacting stumbling and a sideways fall on the hip. The results of the analyses are quantified with experimental data from previous work. With regard to fracture pattern, stiffness and failure load the simulations of the load case stumbling delivered the most stable and accurate results. In general, mapping of material properties was found to be an appropriate way to reproduce PFF with finite element models.

Experimental analysis of early periprosthetic femoral fractures with uncemented straight hip stems

BackgroundThe periprosthetic femoral fracture is one of the most severe complications after total hip arthroplasty and is associated with an increased mortality. The underlying causes and the patient- and implant-specific risk factors of periprosthetic femoral fractures remain insufficiently understood. The aim of this study was to gain a more profound understanding of the underlying fracture mechanisms and to provide experimental datasets for validation of computational models. MethodsSix cadaveric femurs were implanted with straight hip stems (Zweymueller design) and loaded until fracture reproducing the clinically relevant load cases stumbling and sideways fall. Displacements and the strain distribution on the surface of the femurs and implants, as well as the fracture load and implant subsidence were measured. FindingsFor the load case stumbling the mean fracture load was 6743 N and two different mechanisms leading to fracture could be identified: high subsidence with low femoral bending and small subsidence with high femoral bending. For the load case sideways fall the mean fracture load was 1757 N and both tested femurs fractured due to a rotation of the hip stem around its own axis. The detailed datasets provided by this study can be used in future computational models. InterpretationWe demonstrated that the underlying fracture mechanisms of periprosthetic femoral fractures can be fundamentally different in the load case stumbling. The seating and exact position of the hip stem in the femur may correlate with implant subsidence and therefore lead to different types of fracture mechanisms resulting in different patient-specific fracture risks.

Preserved periprosthetic bone stock at 5 years post-operatively with uncemented short hip stem in both collared and collarless version

IntroductionPrevious bone density studies have generally shown bone resorption around both cemented and uncemented total hip arthroplasty (THA) stems. This is presumed to be due to stress shielding. Short stems have been introduced partly to preserve bone in the proximal femur by a more physiological loading of the bone. The purpose of this study was to evaluate bone remodeling around a short, fully hydroxyapatite-coated titanium stem that comes in a collared and collarless version.Patients and methodsA prospective cohort of 50 patients included in a study evaluating the Furlong Evolution stem has been followed for 5 years. Examination was done with dual energy X-ray absorptiometry (DXA) postoperatively, at 1, 2 and 5 years. Clinical outcome was followed with radiography and both general and hip specific outcome measures.ResultsThe two versions of the stem behaved similarly regarding bone remodeling. After an initial decrease up to 1 year, bone mineral density (BMD) increased in all Gruen zones up to 2 years and at 5 years bone stock was still preserved compared with postoperatively (net BMD + 1.2% (95% CI − 0.4 to 2.8)). Increase in BMD occurred mainly in the greater trochanter and distally around the stem with a decrease in the calcar area. Both versions showed excellent clinical outcome up to 5 years.ConclusionThis short stem seems to preserve proximal bone stock up to 5 years, exhibiting similar behaviour both with and without a collar.Trial registration number and date of registrationClinicalTrials.gov, (identifier: NCT01894854). July 10, 2013.

Short-term success of proximal bone stock preservation in short hip stems: a systematic review of the literature.

Total hip arthroplasty is performed more frequently in younger patients nowadays, making long-term bone stock preservation an important topic. A mechanism for late implant failure is periprosthetic bone loss, caused by stress shielding around the hip stem due to different load distribution. Short stems are designed to keep the physical loading in the proximal part of the femur to reduce stress shielding. The aim of this review is to give more insight into how short and anatomic stems behave and whether they succeed in preservation of proximal bone stock.A systematic literature search was performed to find all published studies on bone mineral density in short and anatomic hip stems. Results on periprosthetic femoral bone mineral density, measured with dual-energy X-ray absorptiometry (DEXA), were compiled and analysed per Gruen zone in percentual change.A total of 29 studies were included. In short stems, Gruen 1 showed bone loss of 5% after one year (n = 855) and 5% after two years (n = 266). Gruen 7 showed bone loss of 10% after one year and –11% after two years. In anatomic stems, Gruen 1 showed bone loss of 8% after one year (n = 731) and 11% after two years (n = 227). Gruen 7 showed bone loss of 14% after one year and 15% after two years.Short stems are capable of preserving proximal bone stock and have slightly less proximal bone loss in the first years, compared to anatomic stems. Cite this article: EFORT Open Rev 2021;6:1040-1051. DOI: 10.1302/2058-5241.6.210030

Clinical and radiographic outcomes after total hip arthroplasty with the NANOS neck preserving hip stem: a 10 to 16-year follow-up study

BackgroundShort-stem Hip Arthroplasty (SHA) are increasingly implanted in recent years thanks to their potential advantage in preserving metaphyseal bone-stock. Among them, the NANOS® short-stem implant demonstrated satisfactory results to short and mid-term. The purpose of this retrospective study was to evaluate the clinical and radiographic outcome of the Nanos® short stem at a minimum follow-up of 10 years.MethodsSixty-seven patients aged 53 ± 20 years were enlisted in the study, for a total of 72 hips. Primary outcomes were survivorship of the implant and clinical outcome measured using the Hip disability and Osteoarthritis Outcome scores (HOOS) and the Short Form Survey (SF12) questionnaire. The secondary outcome was a radiological evaluation calculating the inclination and the anteversion angle of the acetabular cup for each implant and investigating osteolysis, heterotopic ossifications and stem position.ResultsWe observed a 95.5% stem survivorship. The complication rate was 7.6% and three implants underwent revision because of an aseptic loosening, an infection and a periprosthetic fracture due to trauma.Among 58 patients (63 hips) evaluated in an outpatient visit 10–16 years after surgery, improvement in clinically relevant scores comparing with baseline was observed: HOOS score increased after surgery in all its subcategories (from 32.25 ± 14.07% up to 91.91 ± 9.13%) as well as SF12 which increased by more than 18 percentage points.On clinical assessment, the range of motion (ROM) was restored at follow-up, 1 patient (1.7%) showed a squeaking hip and 2 (3.4%) reported leg-length discrepancy. Neutral stem positioning was achieved in 58 hips and heterotopic ossifications occurred in 10 hips (16%).ConclusionsThe current study reports good clinical and radiological outcomes following NANOS® short-stem hip implant at minimum 10 years-follow-up. Since the high rate of stem survivorship, the low complication rate demonstrated and the overall patient satisfaction, our results suggest NANOS® neck-preserving prostheses should be considered as a valid alternative to standard implants.

Creation and finite-element analysis of multi-lattice structure design in hip stem implant to reduce the stress-shielding effect

The term stress-shielding is frequently used to mention the reduction in mechanical stimulus in the surrounding bone due to the presence of a biomaterial inert implant whose mechanical properties are superior to bone. As the natural consequence of this, mineral loss occurs in the bone over time and creating subsequent weakness. One of the methods to reduce stress-shielding problem is to develop hip-stem implant designs that will transfer the load more to the bone. Therefore, in this study, multi-lattice designs were developed to reduce the stress-shielding effect in hip implant applications. For this, the proximal part of the hip implant stems has been divided into three parts. Simple cubic, body centered cubic, and face centered cubic lattice structures were created on the upper parts. Inner vertical and inner vertical + inner horizontal beams were added to the lattice structure of the upper part for middle and lower parts, respectively. Due to the multi-lattice designs, the maximum von Mises stress values on the hip implant stem were reduced from 289 to 189 MPa, as well as a weight reduction of up to 25.89%. Stress-shielding signals were obtained by determining the change in strain energy per unit bone mass caused by the presence of the femoral hip implant stem and its ratio to intact bone. In the case of using hip-stems having multi-lattice designs, there is a significant increase (max. 150.47%) in stress-shielding signals from different zones of the femur.

Bone Ingrowth Around an Uncemented Femoral Implant Using Mechanoregulatory Algorithm: A Multiscale Finite Element Analysis.

The primary fixation and long-term stability of a cementless femoral implant depend on bone ingrowth within the porous coating. Although attempts were made to quantify the peri-implant bone ingrowth using the finite element (FE) analysis and mechanoregulatory principles, the tissue differentiation patterns on a porous-coated hip stem have scarcely been investigated. The objective of this study is to predict the spatial distribution of evolutionary bone ingrowth around an uncemented hip stem, using a three-dimensional (3D) multiscale mechanobiology-based numerical framework. Multiple load cases representing a variety of daily living activities, including walking, stair climbing, sitting down, and standing up from a chair, were used as applied loading conditions. The study accounted for the local variations in host bone material properties and implant-bone relative displacements of the macroscale implanted FE model, in order to predict bone ingrowth in microscale representative volume elements (RVEs) of 12 interfacial regions. In majority RVEs, 20-70% bone tissue (immature and mature) was predicted after 2 months, contributing toward a progressive increase in average Young's modulus (1200-3000 MPa) of the interbead tissue layer. Higher bone ingrowth (mostly greater than 60%) was predicted in the anterolateral regions of the implant, as compared to the posteromedial side (20-50%). New bone tissue was formed deeper inside the interbead spacing, adhering to the implant surface. The study helps to gain an insight into the degree of osseointegration of a porous-coated femoral implant.

Removing Well-Fixed, Collared and Noncollared Tapered Hip Stems Without an Extended Trochanteric Osteotomy Using a Novel Stem Removal System.

Improvements in materials, components, and surgical techniques in cementless total hip arthroplasty are resulting in improved femoral stem fixation through bony ongrowth or ingrowth. While improved femoral stem fixation is one reason for the current excellent total hip survivorship, indications for stem removal such as infection, implant fracture, or osteolysis remain. A commonly used technique for fully ingrown femoral stems is an extended trochanteric osteotomy which can result in comminuted fractures of the proximal femur during stem removal requiring additional fixation. Therefore, a novel hip stem removal was developed to facilitate removal of these well-ingrown stems without the need for an extended trochanteric osteotomy. This study describes the removal system and surgical technique and presents a case series of successfully removed ingrown stems.

Numerical Simulation of Electric Field Distribution around an Instrumented Total Hip Stem

Presently, total joint replacement (TJR) is a standard procedure in orthopedic surgery. Adequate osseointegration of the implant components still remains a clinical issue. However, active stimulation of bone tissue to enhance bone ongrowth at the implant surfaces has not been widely investigated so far. For the last several years, invasive electromagnetically induced osseotherapy has been employed in clinical practice, e.g., for the treatment of avascular necrosis, femoral neck fractures, and pseudarthrosis. In the present study, the approach of exploiting the electric stimulation effect was transferred to the field of TJR. Therefore, a commercially available total hip stem was instrumented with an electrode on its surface in order to generate an electric field supporting the regeneration of the surrounding bone tissue. The objective was to conduct numerical simulations validated by experimental investigations as a proof of concept for an instrumented electro-stimulative total hip stem. The results revealed that the calculated electric field around a total hip stem fulfills the requirements to stimulate adjacent bone tissue when using clinically applied electric voltages. The derived numerical and experimental data of electric potentials and corresponding electric fields are encouraging for the implementation of active electrical stimulation in uncemented total hip stems to enhance their osseointegration.

A neck-preserving short stem better reconstructs the centre of rotation than straight stems: a computed tomography-based cadaver study.

Short femoral hip stems with a metaphyseal anchoring concept have been designed to treat younger patients with good bone quality. The aim of this study was to reconstruct the centre of rotation and soft tissue balancing and preserve bone in the long-term perspective. Eighteen human femurs were randomised into three groups: (1) metaphyseal anchoring short stem, (2) shortened straight stem, (3) straight stem). Prior to the implantation of the hip stems, a computed tomography (CT) of the bones was performed and the femoral ante-torsion and ante-tilt was measured and compared to the results of the post-implantation CT. This could be calculated based on the 3D coordinates taken from the pre- and post-op CT scans, which were transformed into the same coordinate systems. The mean preoperative caput-collum-diaphyseal (CCD) angle for the three groups was 126.87° ± 3.50° (Group 3: 129.64° ± 3.53°, Group 1: 123.76° ± 5.56°, Group 2: 127.53° ± 1.42°) and was consistent with published reports. The postoperative CCD angles with 126.85° ± 3.43° were within a very good reconstruction range for all three groups. The anterior offset comparison among these three groups showed significant difference in reconstruction. The smallest difference between the anatomical (preoperative) and postoperative condition was seen in Group 1 (1.47° ± 0.60°), followed by Group 2 (3.60° ± 0.23°) and Group 3 (8.00° ± 0.70°) groups. The horizontal offset showed no significant difference among the groups and was within the window of ± 5mm. In this cadaver study, we found that the metaphyseal anchoring, partially neck-preserving short hip stem best reconstructs the ante-torsion and the ante-tilt of the femoral neck. Therefore, it can be a useful stem in younger or active middle-aged patients.

Comparison of Functionally Graded Hip Stem Implants with Various Second-Generation Titanium Alloys

Total hip Arthroplasty (THA) is performed every year at a very high frequency to improve the quality of life of thousands of patients all over the globe. Nevertheless, the expected service life of such surgery remains unsuitable for patients under 50 years old. This is mainly related to stress shielding and the potential adverse tissue reaction to some of the elements of the market-dominant implant materials. In this research, functionally graded (FG) implant designs of several titanium alloys layered with hydroxyapatite (HA) are proposed to provide lower implant stiffness compared to a solid stem to approach the requirements of human bone. Moreover, TNZT (Ti35Nb7Zr5Ta), and TMZF (Ti12Mo6Zr2Fe) second-generation titanium alloys are studied as a replacement for the famous Ti6Al4V alloy to avoid the adverse tissue reactions related to aluminum and vanadium elements. The different FG models are numerically tested using a 3D finite element simulation after virtual implantation in a femur bone under the dynamic load of a patient descending stairs. In the numerical study, the variation in stress distribution and strain energy in a femur bone is assessed for different FG hip stems as well as the axial stiffness of the hip stems. Results indicated an increase in strain energy and von Mises stress in the cortical and cancellous bones using FG hip stems. Additionally, the axial stiffness is reduced for all FG hip stems relative to the commercial Ti6Al4V hip stem.

Digital templating for the implantation of a curved short hip stem with an anterolateral MIS approach shows gender differences in digital templating

PurposeDigital templating shows reliable accuracy for straight stem systems. In recent years, the implantation of short stems through minimally invasive approaches has gained more popularity. Minimally invasive approaches (MIS) show the risk of undersizing femoral components. Therefore, we questioned the planning adherence for a curved short stem and a bi-hemispherical acetabular cup implanted through an anterolateral MIS approach.MethodsA consecutive series of 964 hips (index surgery between 2014 and 2019) with Fitmore® curved short stem and Allofit/-S® acetabular cup (both ZimmerBiomet Inc, Warsaw, IN) were included. Preoperative digital templating was conducted anterior–posterior (AP) digital radiographs of the hip using mediCAD® version 5.1 (Hectec GmbH, Altdorf, Germany). The templates of acetabular and femoral components (offset option and stem size) were retrospectively evaluated for general adherence, and according to sex, BMI and planner’s experience.ResultsPlanning adherence for the exact offset option was 70.6 and 21.6% for exact offset option and stem size. Adherence for acetabular cup ± 1 size was 74.8%. A significant difference between male and female patients for the offset option could be found (p = 0.03, z = −2983). In 22.5% of male patients, an offset option one size higher and in 12.3% of female patients an offset option one size smaller than templated was used intraoperativelyConclusionDigital templating for the Fitmore® stem in cementless THA with a minimally invasive anterolateral approach shows comparable planning adherence to the existing literature for this cementless short stem. However, a lower planning adherence was detected compared to conventional straight stem systems. In male patients, the femoral offset is frequently undersized and in female patients frequently oversized compared to the preoperative plan. Surgeons should be aware of this difficulty in digital templating for Fitmore® hip stem.

Endurance testing and finite element simulation of a modified hip stem for integration of an energy harvesting system.

Instrumented implants are a promising approach to further improve the clinical outcome of total hip arthroplasties. For the integrated sensors or active functions, an electrical power supply is required. Energy harvesting concepts can provide autonomous power with unlimited lifetime and are independent from external equipment. However, those systems occupy space within the mechanically loaded total hip replacement and can decrease the life span due to fatigue failure in the altered implant. We previously presented a piezoelectric energy harvesting system for an energy-autonomous instrumented total hip stem that notably changes the original implant geometry. The aim of this study was to investigate the remaining structural fatigue failure strength of the metallic femoral implant component in a worst-case scenario. Therefore, the modified hip stem was tested under load conditions based on ISO 7206-4:2010. The required five million cycles were completed twice by all samples (n = 3). Additionally applied cycles with incrementally increased load levels up to 4.7 kN did not induce implant failure. In total, 18 million cycles were endured, outperforming the requirements of the ISO standard. Supplementary finite element analysis was conducted to determine stress distribution within the implant. A high stress concentration was found in the region of modification. The stress level showed an increase compared to the previously evaluated physiological loading situation and was close to the fatigue data from the literature. The stress concentration factor compared to the original geometry amounted to 2.56. The assessed stress level in accordance with the experimental fatigue testing can serve as a maximum reference value for further implant design modifications and optimisations.

A single-surgeon experience in reconstruction of femoro-acetabular offset and implant positioning in direct anterior approach and anterolateral MIS approach with a curved short stem

PurposeMinimally invasive surgery using short stems in total hip arthroplasty gained more popularity. The differences in change of hip offset and implant positioning in minimally invasive approaches are not fully known. Therefore, this study was conducted to evaluate the difference in reconstruction of hip offset and implant positioning in direct anterior approach (DAA) and minimally invasive anterolateral approach (AL MIS).MethodsA single surgeon series of 117 hips (117 patients; mean age 65.54 years ± 11.47; index surgery 2014–2018) were included and allocated into two groups: group A (DAA) with 70 hips and Group B (AL MIS) with 47 patients operated. In both groups the same type of cementless curved short hip stem and press fit cup was used.ResultsBoth groups showed an equal statistically significant increase of femoral (p < 0.001) and decrease of acetabular offset (p < 0.001). Between both groups no statistically significant difference in offset reconstruction, leg length difference or implant positioning could be found. Leg length increased in both groups significantly and leg length discrepancy showed no difference (group A: − 0.06 mm; group B: 1.11 mm; p < 0.001). A comparable number of cups were positioned outside the target zone regarding cup anteversion.ConclusionThe usage of a curved short stem shows an equal reconstruction of femoro-acetabular offset, leg length and implant positioning in both MIS approaches. The results of this study show comparable results to the existing literature regarding change of offset and restoration of leg length. Malposition of the acetabular component regarding anteversion poses a risk.