High Concentrations Of Heavy Metals Research Articles

Stress of cupric ion and oxytetracycline in Chlorella vulgaris cultured in swine wastewater

Chlorella culturing has the advantages in treatment of wastewater including swine wastewater from anaerobic digesters due to the product of biolipids and the uptake of carbon dioxide. However, there often exist high concentrations of antibiotics and heavy metals in swine wastewater which could be toxic to chlorella and harmful to the biological systems. This study examined the stress of cupric ion and oxytetracycline (OTC) at various concentrations on the nutrient removal and biomass growth in Chlorella vulgaris culturing in swine wastewater from anaerobic digesters, and its biochemical responses were also studied. Results showed that dynamic hormesis of either OTC concentration or cupric ion one on Chlorella vulgaris were confirmed separately, and the presence of OTC not only did not limit biomass growth and lipids content of Chlorella vulgaris but also could mitigate the toxicity of cupric ion on Chlorella vulgaris in combined stress of Cu2+ and OTC. Extracellular polymeric substances (EPS) of Chlorella vulgaris were used to explain the mechanisms of stress for the first time. The content of proteins and carbohydrates in EPS increased, and the fluorescence spectrum intensity of tightly-bound EPS (TB-EPS) of Chlorella vulgaris decreased with increasing concentration of stress because Cu2+ and OTC may be chelated with proteins of TB-EPS to form non-fluorescent characteristic chelates. The low concentration of Cu2+ (≤1.0 mg/L) could enhance the protein content and promote the activity of superoxide dismutase (SOD) while these parameters were decreased drastically under 2.0 mg/L of Cu2+. The activity of adenosine triphosphatase (ATPase) and glutathione (GSH) enhanced with the increase of OTC concentration under combined stress. This study helps to comprehend the impact mechanisms of stress on Chlorella vulgaris and provides a novel strategy to improve the stability of microalgae systems for wastewater treatment.

Distribution Characteristics of Heavy Metals in Different Particle Size Fractions of Chinese Paddy Soil Aggregates

In recent years, the migration and transformation of heavy metals (HMs) in soil has become a hot issue. Soil particle size has an important effect on the environmental behavior of HMs in soil. The distribution of HMs in soil is strongly affected by the size of a soil aggregate. In this study, paddy samples in both cultivated and uncultivated soils were collected from Anhui Province, China. The soils were sieved into six particle size fractions (diameters of >4000, 4000–2000, 2000–1000, 1000–250, 250–53, and <53 μm) and the wet digestion method was used to determine the concentrations of Cd, Cr, Pb, and As in the soil aggregates. The results showed that the surface soils were characterized by the largest proportion of coarsest aggregates of >4000 μm particles. Moreover, the concentrations of Cd, Cr, Pb, and As were elevated in cultivated paddy soils compared to uncultivated soils. The accumulation of HMs in all paddy soils increased with decreasing particle size. Although the smallest particle size fractions accounted for only 5.65–17.28%, they provided the highest distribution factor (DF) of Cr (1.35), As (1.25), Cd (1.28), and Pb (1.38). The highest contributions of HMs came from the coarser fractions (>2000 μm); however, for Cr, Pb, Cd, and As, the mass loading of <53 μm particles was up to 15.90%, 14.41%, 15.21%, and 15.70%, respectively. The highest content of HMs was found in the finest aggregate, with a pattern of decreasing with increasing aggregate size. In addition, the leachability behaviors of different HMs in different particle size aggregates were different. The leachability behaviors of Cr and Pb in the coarse particle size fractions were the highest, while the leachability behaviors of As and Cd in the less than 250 μm particle size fractions were 10–100 times higher than those of Cr and Pb. A correlation analysis showed that the particle distributions of Fe, TOC, and Mn had significant influences on the distributions of Pb, Cd, As, and Cr. This study provides a theoretical basis for the prevention, treatment, and remediation of HMs pollution in soil.

Medical waste management in Al-Kut City

This research investigates solid waste management in Al-Kut City. It included the collection of medical and general solid waste generated in five hospitals different in their specialization and capacity through one week, starting from 03/02/2012. Samples were collected and analyzed periodically to find their generation rate, composition, and physical properties. Analysis results indicated that generation rate ranged between (1102 – 212) kg / bed / day, moisture content and density were (19.0 % - 197 kg/ m3) respectively for medical waste and (41%-255 kg/ m3) respectively for general waste. Theoretically, medical solid waste generated in Al-Kut City (like any other city), affected by capacity, number of patients in a day, and hospital specialty The research exposed the incorrect ways used in collecting, storing, waste transport, and inefficient incinerators processing .Laboratory test for six ash collected samples indicated high concentration of heavy metals (Pb, Cd, Cr) , having the rang of (51.0 – 62.0) mg / l of lead, (3.0 – 8.5) mg / l for cadmium, and (43.0 -69.0) mg / l for chrome. In comparison with the US Environmental Protection Agency standards, these samples are higher than the recommended levels that may threat groundwater. A comprehensive and integrated solution there must be to manage medical waste, with the participation of all parties concerned, especially, the Ministry of Health, environment authorities concerned, and the participation of civil society organizations. A color-code trash bags and containers are recommended by the World Health Organization and the Environmental Protection Agency to be used in hospitals that propose red bags for collecting medical waste while black bags for general waste provided that they are resistant to tearing seeping and should be provided in sufficient numbers.

Glass recovery and production of manufactured aggregate from MSWI bottom ashes from fluidized bed and grate incineration by means of enhanced treatment

Enhanced treatment of incineration bottom ashes (IBA) from municipal solid waste incineration can contribute to a circular economy since not only metals can be recovered but also glass for recycling. Moreover, the remaining mineral fraction can be utilized in concrete as manufactured aggregate. To evaluate the effects of an enhanced treatment, three IBAs from fluidized bed combustion (FB-IBAs) and three grate incineration bottom ashes (G-IBAs) were standardly treated in a jig and further processed on a pilot scale, including improved metal recovery and sensor-based glass separation. The removed glass fractions were weighed and their composition was assessed by means of manual sorting. The manufactured aggregate was also sorted manually and its total and leachate contents were determined before and after aging. Results showed general differences between FB-IBAs and G-IBAs. For G-IBAs, higher contents of heavy metals and residual metal pieces were determined, while the share of glass removed was low compared to FB-IBA. The treated mineral fractions from G-IBA contained more mineral agglomerates, whereas FB-IBAs contained more glass. However, the glass-fractions removed from FB-IBAs need further treatment to be accepted in glass recycling. Austrian limit values for utilization in concrete were met by all manufactured aggregates produced from FB-IBA, but only by one from G-IBA. Overall, the enhanced treatment in the study performed well compared to the literature. Nevertheless, further investigations are necessary to improve the recyclability of the recovered glass fractions and to determine the technical suitability of manufactured aggregates produced from IBAs.

Exploring invertebrate indicators of ecosystem health by focusing on the flow transitional zones in a large, shallow eutrophic lake

The river–lake transitional zone provides a unique environment for the biological community and can reduce pollution inputs in lake ecosystems from their catchments. To explore environmental conditions with high purification potential in Lake Taihu and indicator species, we examined the river-to-lake changes in water and sediment quality and benthic invertebrate communities in the transitional zone of four regions. The spatial variations in the environment and invertebrate community observed in this study followed the previously reported patterns in Taihu; the northern and western regions were characterized by higher nutrient concentrations in water, higher heavy metal concentrations in sediment, and higher total invertebrate density and biomass dominated by pollution-tolerant oligochaetes and chironomids. Although nutrient concentrations were low and transparency was high in the eastern region, the taxon richness was the lowest there, which disagreed with the previous findings and might be due to a poor cover of macrophytes in this study. The river-to-lake change was large in the southern region for water quality and the invertebrate community. Water circulation induced by strong wind-wave actions in the lake sites of the southern region is assumed to have promoted photosynthetic and nutrient uptake activities and favored invertebrates that require well-aerated conditions such as polychaetes and burrowing crustaceans. Invertebrates usually adapted to brackish and saline environments are suggested to be indicators of a well-circulated environment with active biogeochemical processes and a less eutrophic state in Taihu, and wind-wave actions are key to maintaining such a community and natural purifying processes.

Heavy Metals in Fly Ash as a Factor Limiting Its Use in Fertilizing Composts

Composting enables the recycling of significant amounts of biodegradable waste, while ensuring its disposal. The addition of fly ash increases the concentration of fertilizing substances in the compost. Compost is a source of many nutrients for plants. The addition of fly ash might also cause a slower release of these nutrients into an aqueous solution, meeting the fertilization needs of plants over a longer period of time. Tests were carried out using sewage sludge (WWTP Piaseczno, 163,500 P.E.), straw as a structure-forming material and fly ash (WWTP Krakow, 780,000 P.E.). The compost obtained in the research was analyzed in terms of environmental conditions specified in legal regulations. The most favorable compost mass density (520 kg/L) and the amount of air supplied to the process (5.0 L/(h∙kg d.m.)) were determined. The addition of fly ash to the compost mass did not significantly affect the temperature distribution obtained in the process. The increase in fly ash content increased the pH of the compost mass and was associated with higher nitrogen losses. It was found that the factor which may limit the possibility of using fly ash as a compost substrate is the presence of higher concentrations of heavy metals, especially chromium. It was determined that the maximum addition of fly ash to the compost mass was 154 kg d.m.ash/(ton d.m.straw+sludge).

NUTRITIONAL VALUE AND HEAVY METAL CONTENT OF CRAB MEAT AND ITS BYPRODUCT WHITE MUD CRAB Scylla paramamosain

Mud crab is fishery commodity that has high economic value and rich of nutritional aspect such as essential amino acids, vitamins, minerals, and fatty acids. In addition, high concentrations of heavy metals in the natural habitat of crabs can accumulate in these organisms which can endanger health if consumed. However, there is little information regarding the nutritional and heavy metal content of meat and byproducts in mud crab. The objective of the study are to compare the beneficial component of the meat and byproduct of Scylla paramamosain and to investigate food safety from heavy metal contamination. Proximate, vitamin A, D, and E content were analyzed using HPLC, vitamin B1, B2, C, and amino acid profile was determined by using UPLC, vitamin B12 was determined by LC-MS, mineral and heavy metal were determined by standard method of AOAC. In addition, the determination of fatty acid was analyzed by gas chromatography. Result showed that protein per gram as the majority content of each form (10.24% in crab meat and 12.47% in byproduct). Vitamin B2, B12, and E were detected in sample. On contrary, heavy metals examined in this study were not detected. L-Glutamic acid was the most abundant of amino acids composition (11037.79 mg/kg of crab meat and 15993.22 mg/kg of byproduct), while omega-3 fatty acids, omega-6 fatty acids, and omega-9 fatty acids are also contained in this species. The result showed Scylla paramamosain as source of beneficial food and safe to consume.

Resourceful Treatment of Battery Recycling Wastewater Containing H2SO4 and NiSO4 by Diffusion Dialysis and Electrodialysis

Facing the increasing demand for batteries worldwide, recycling waste lithium batteries has become one of the important ways to address the problem. However, this process generates a large amount of wastewater which contains high concentration of heavy metals and acids. Deploying lithium battery recycling would cause severe environmental hazards, would pose risks to human health, and would also be a waste of resources. In this paper, a combined process of diffusion dialysis (DD) and electrodialysis (ED) is proposed to separate, recover, and utilize Ni2+ and H2SO4 in the wastewater. In the DD process, the acid recovery rate and Ni2+ rejection rate could reach 75.96% and 97.31%, respectively, with a flow rate of 300 L/h and a W/A flow rate ratio of 1:1. In the ED process, the recovered acid from DD is concentrated from 43.1 g/L to 150.2 g/L H2SO4 by the two-stage ED, which could be used in the front-end procedure of battery recycling process. In conclusion, a promising method for the treatment of battery wastewater which achieved the recycling and utilization of Ni2+ and H2SO4 was proposed and proved to have industrial application prospects.

Recovery of residual metals from jarosite waste using chemical and biochemical processes to achieve sustainability: A state-of-the-art review

Jarosite is a residue that is generated as a by-product during zinc extraction, and it consists of various types of heavy metal (loid)s such as arsenic, cadmium, chromium, iron, lead, mercury and silver. Due to the huge jarosite turn-over rate, and less efficient and expensive residual metal extraction processes, the zinc-producing industries dispose this waste in landfills. However, the leachate generated from such landfills contains a high concentration of heavy metal (loid)s that could contaminate the nearby water resources and cause environmental concern and human health risk. Various thermo-chemical and biological processes have been developed for the recovery of heavy metals from such waste. In this review, we have discussed all those pyrometallurgical, hydrometallurgical, and biological. Those studies were critically reviewed and compared on the basis of their techno-economic differences. The review indicated that these processes have their own benefits and drawbacks such as overall yield, economic and technical constraints, and the need for more than one process to mobilize multiple metal ions from jarosite. Also, in this review, the residual metal extraction processes from jarosite waste have been linked with the relevant UN Sustainable Development Goals (SDGs), which can be useful for a better approach to sustainable development.

Heavy metals and metalloids accumulation in common beans (Phaseolus vulgaris L.): A review

Heavy metals (HMs) and metalloids (Ms) such as arsenic (As), cadmium (Cd), mercury (Hg), and lead (Pb) represent serious environmental threats due to their wide abundance and high toxicity. Contamination of water and soils by HMs and Ms from natural or anthropogenic sources is of great concern in agricultural production due to their toxic effects on plants, adversely affecting food safety and plant growth. The uptake of HMs and Ms by Phaseolus vulgaris L. plants depends on several factors including soil properties such as pH, phosphate, and organic matter. High concentrations of HMs and Ms could be toxic to plants due to the increased generation of reactive oxygen species (ROS) such as (O2•-), (•OH), (H2O2), and (1O2), and oxidative stress due to an imbalance between ROS generation and antioxidant enzyme activity. To minimize the effects of ROS, plants have developed a complex defense mechanism based on the activity of antioxidant enzymes such as SOD, CAT, GPX, and phytohormones, especially salicylic acid (SA) that can reduce the toxicity of HMs and Ms. This review focuses on evaluating the accumulation and translocation of As, Cd, Hg, and Pb in Phaseolus vulgaris L. plants and on their possible effects on the growth of Phaseolus vulgaris L. in soil contaminated with these elements. The factors that affect the uptake of HMs and Ms by bean plants, and the defense mechanisms under oxidative stress caused by the presence of As, Cd, Hg, and Pb are also discussed. Furthermore, future research on mitigating HMs and Ms toxicity in Phaseolus vulgaris L. plants is highlighted

Heavy Metal Dispersion in a Hydrological Sub-Basin as Consequence of Mining Activity in Taxco, Guerrero (Southern Mexico)

The mining industry generates high concentrations of heavy metals (HMs) susceptible to being released into surface and ground water. The objective of this work was to determine the concentration and dispersion of HMs in surface water and ground water in a hydrological sub-basin located in southwest Mexico. The samples were collected as following: 24 samples from streams, rivers, and one lake, and 15 samples from springs, located along the Taxco-Cocula sub-basin. A total of 78 samples were collected in the dry and rainy seasons. Physicochemical parameters, major ions, and HMs were analyzed. The pH, Eh, electrical conductivity, and total dissolved solids were analyzed in situ, while the concentrations of anions, cations, and HMs were measured in the laboratory. The results were treated with multivariate analysis and PHREEQC simulation. The highest recorded values (in mg/L) were in surface water, where the HMs in the dry season were Al (28.63), As (0.60), Cd (1.78), Cu (1.10), Fe (68.27), Mn (21.47), Pb (0.02), and Zn (208.80). These high concentrations exceed the limits established by national and international regulations for drinking water. The ground water did not indicate pollutants associated to the mining industry. On the other hand, in the rainy season, the surface water showed a decrease in the concentrations of the measured heavy metals. The hypsometric gradient and the hydrogeological and meteorological characteristics of the Taxco-Cocula sub-basin are the factors that contribute to the dilution and dispersion of the HMs along the 60 km of its length.

EFFECTS OF LEAD AND CADMIUM ON SHOOT LENGTH AND ROOT LENGTH OF CASCABELA THEVETIA (L.) LIPPOLD

Agricultural sustainability and civilization of society enormously depend on land. However, contamination of soil due to heavy metals is a major threat to mankind. Cadmium is one of the most toxic metals in the environment and has noxious effects on vegetative growth. Lead is the second ranked of most widely distributed hazardous substances in the environment and can cause morphological, physiological, and biological dysfunctions in plants. This study investigates the effect of various concentrations of lead and cadmium, i.e. 400mg, 800mg, 1200mg, 1600mg Pb kg-1 and 5mg, 10mg, 15mg, 20mg Cd kg-1, on root length and shoot length of Cascabela thevetia (L.) Lippold. The results states lead treatments have decreased the length of shoot by 19 cm and 11.99 cm of root. Cadmium treatments to the plants have decreased by 20 cm and 11 cm of shoot and root respectively. Higher concentrations of heavy metals in the soil can significantly reduce root lengths and shoot lengths.

Formation of waters of tungsten-ore areas under the influence of natural and anthropogenic factors (Eastern Transbaikalia, Russia)

The industrial development of tungsten deposits in Eastern Transbaikalia contributed to a significant deterioration of the environmental situation in the adjacent territories. Heavy-metal water contamination has become a serious problem in the mining areas. The most dangerous are wastes of sulphide ores, the oxidation of which leads to the formation of acidic drains with abnormally high concentrations of heavy metals. The features of the composition of the waters formed in and around the five tungsten deposits were studied and significant differences in their physical and chemical characteristics were shown. The most saline acidic, sulphate waters with the maximum content of heavy metals are recorded in the drainages of the tailings of beneficiation plants and rock dumps and in the ponds of sludge depositories and deposits with an increased ore sulphide content. The groups of elements posing the greatest danger to aquatic ecosystems were identified as Cd, Cu, Zn, Be, Al, Co, Th, Mn in acidic and slightly acidic waters and W, Mo, U, As, Mn in slightly alkaline and alkaline waters. Based on the Eh-pH water parameter ratio, three types of hydrogeochemical environments formed in the mining areas of tungsten deposits were identified. Metal migration in the waters occurs mainly in the form of simple cations, sulphate, fluoride, hydrocarbonate, carbonate and hydroxyl complexes. Geochemical barriers of oxygen, sorption, acidic and alkaline types were studied in the areas around the deposits. The main factors determining the physical and chemical parameters of the waters are shown, including the regional factor, specifically, the ore and host rock composition, the water exchange intensity, and the technogenic factor, which causes a high level of water pollution.

Driving factors on accumulation of cadmium, lead, copper, zinc in agricultural soil and products of the North China Plain

The accumulation of heavy metals in agricultural soils concerns food security. By using the Geographical Detector, this study investigated the influence of six types of factors (eleven factors) on the accumulation of Cd, Pb, Cu, Zn in agricultural soil and products of the North China Plain and confirmed the dominant factor. The results showed that heavy metals had accumulated in regional agricultural soils and the accumulation of Cd was severe. The accumulation of heavy metals was significantly influenced by policy factors (the management and reduction in usage of fertilizers and pesticides), fertilization factors (application of organic and chemical fertilizers), pesticide factors (application of herbicide and insecticide) and atmospheric deposition factors (heavy metal concentration in atmospheric deposition). The policy factor dominated the other three types of factors. Atmospheric deposition and the excess application of fertilizers and pesticides directly lead to the accumulation of heavy metals. Due to the high concentrations of heavy metals and abundant application amounts, organic fertilizers have contributed high levels of heavy metals to agricultural soils. This study suggests that formulated fertilization and action plans for pesticide reduction could effectively decrease the accumulation of heavy metals in agricultural soils and products in the study area.

Spatial Distribution Characteristics and Source Analysis of Heavy Metals in Urban River Surface Sediments from the Lanzhou Reach of the Yellow River

In order to investigate the contamination characteristics and potential sources of heavy metals from the urban river surface sediments in the Yellow River Basin, we selected the Lanzhou reach of the Yellow River as the object of investigation. A total of 46 surface sediment samples were collected along the Lanzhou reach of the Yellow River, and the contents of eight heavy metals, Cr, Ni, Cu, Zn, As, Cd, Hg, and Pb, were determined by using inductively coupled plasma mass spectrometry and an atomic fluorescence spectrometer. Contamination indexes including single factor pollution index (Pi) and geo-accumulation index (Igeo), together with the sediment pollution index (SPI), were used to assess heavy metal pollution characteristics and ecological risk levels in the urban river surface sediments of the Lanzhou reach of the Yellow River. Pearson's correlation analysis (CA), positive matrix factorization (PMF), and principal component analysis/absolute principal component score (PCA/APCS) were jointly employed to quantitatively analyze pollution sources of heavy metals. The results showed that the mean concentrations of the majority of heavy metals exceeded their corresponding background values of Gansu Province and Lanzhou City with the exception of As, and the spatial distribution of high concentrations of heavy metals was mainly concentrated in the corner of the river. Based on the single factor pollution and geo-accumulation indexes of the eight heavy metals, in the Lanzhou reach of the Yellow River, Cr was the dominant pollution element in the urban river surface sediments, followed by Cd and Ni. Additionally, the SPI values for the eight heavy metals in the surface sediments ranged from 0.48 to 8.56, presenting natural to low ecological risk level. Furthermore, source apportionment revealed that a mixture source of industrial and agricultural activities (77.6%) was the largest contributor of Cr, Ni, Zn, As, Cd, and Pb in the urban river surface sediments, followed by natural sources (11.4%) and a mixed source of industrial and traffic activities (11%).

Benthic foraminifera as bioindicators for the heavy metals in the severely polluted Hurghada Bay, Red Sea coast, Egypt

Twenty-nine sediment samples were collected from the Hurghada Bay, a heavily polluted bay on the Red Sea of Egypt, to inspect the environmental quality status and anthropogenic consequences on benthic foraminifera. Some foraminiferal species showed deformations in their apertures and coiling directions as a response to environmental stresses. In addition, the FoRAM index, an index used for evaluating the growth of coral reefs, indicated a hazard in the proximity of nearshore stations. To elucidate the relationships between the biological response and chemistry of sediments, eight heavy metals concentrations (Cu, Cd, Zn, Pb, As, Cr, Ni, and Mn) were analyzed using inductively coupled plasma–atomic emission spectrometers (ICP-AES). Interestingly, two groups of benthic foraminiferal associations were illustrated using multivariate statistical analyses. Group I have extremely high heavy metal concentrations, an enriched total organic matter (TOM)%, high deformation percentages, and mud content. Moreover, it is dominated by Ammonia tepida which is regarded as an opportunistic species. Group II includes low to moderately polluted stations, highly enriched living foraminiferal assemblages, and is dominated by the sensitive rotaliids Neorotalia calcar and Amphistegina lobifera. Alternatively, four geochemical indices, EF, CF, Igeo, and PLI, are used to assess the contamination level that shown ominous spots for the nearshore stations of the Hurghada Bay. The pollution indices (HQ and HI) were also conducted to evaluate the risks of carcinogenic heavy metals on human health. Our findings demonstrated that ingestion and dermal exposure have greater carcinogenic hazards for adults and children than inhalation. The lifetime carcinogenic risk (LCR) is significantly higher than the permissible limit and follows this order: Pb > As > Cr > Cd > Ni. To that end, developing strategies to lessen the negative impact of pollution on human health and/or the Red Sea’s biodiversity is an inevitable issue in the present day and future.

Assessment of heavy metals leachability characteristics and associated risk in typical acid mine drainage (AMD)-contaminated river sediments from North China

Acid mine drainage (AMD) is a worldwide environmental problem, characterized by low pH values and high concentrations of heavy metals. Heavy metal pollution of sediments caused by AMD has attracted widespread attention. However, research works on the leachability and distribution characteristics along with the ecological and health risks assessment of AMD-polluted sediment are limited. 15 sediments samples were collected from an AMD-polluted river, Shandi River, North China to analyze the leachability concentration, potential sources, and associated risk of eight metals, namely Ni, Cd, Cu, Zn, Fe2+, Fe3+, Pb, and Mn. Our results showed that Mn, Ni, Fe3+, and Fe2+ were the main leachate pollutants in the Shandi river. Certain levels of ecological risks existed in AMD-polluted stations and Ni was the common key metal that caused the high ecological risk factor in S1, S2, and S4. Cu, Ni, and Zn were the three metals that caused high or moderate risk to zebrafish. Mn and Fe were the main heavy metals that caused non-carcinogenic risks both for adults and children and Ni was another main heavy metal that caused non-carcinogenic risks for children. Ni and Cd can induce carcinogenic risks in these areas. Pearson's correlation and PCA results supported that these metals possibly originate from common AMD–polluted sources. The technology of “gravitational settling-neutralizing filter-aeration-coagulation-filtration” (GSNFACF) was an effective strategy to amend AMD and could be used for future cleaner production and environmental sustainability. These results suggested that the main contaminants in the sediments of the Shandi River should be preferentially treated by the government.

Phytoextraction of al and fe using Eichhornia crassipes in contaminated water from the madín dam

The phytoextraction potential of water hyacinth (Eichhornia crassipes) in the treatment of a representative sample of water of Madín Dam, contaminated with 24.45 mg/L of aluminum (Al) and 5.10 mg/L iron (Fe) was evaluated. Two 60 days experiments were performed, one using young and adult plants and the other with young ones, extracted and substituted every 15 days. The percentage of maximum removal observed in the hyacinth exposed for 60 continuous days was the one of young hyacinths, namely 72%. Besides, those hyacinths extracted every 15 days extracted about 86% of the metals in contaminated water. Eichhornia crassipes turned to be a Al and Fe tolerant species, but not capable of transporting those metals from the roots to the leaves. However, its harvest implies the removal of the whole specimen and therefore the complete extraction of the plant. This indicates that a post-treatment of the extracted hyacinth as a hazardous material would be required, due to its high content of heavy metals.

Accumulation of heavy metals and human health risk assessment of vegetable consumption from a farm within the Korle lagoon catchment

The Korle lagoon is known to have high concentration of heavy metals. The use of land for agriculture and water for irrigation within the Korle Lagoon's catchment constitutes a potential health risk. Due to this, the study assessed the concentration of heavy metals in some vegetables (Amaranth, Spinach, Eggplant, Lettuce, Cauliflower, and Onion) and their corresponding soil from a farm within the Korle Lagoon's catchment. The estimated daily intake (EDI), hazard quotient (HQ), and lifetime cancer risk (LCR) was used to assess their health risks. Among the vegetables tested, heavy metals in lettuce exceeded their recommended guideline level. Additionally, the concentrations of Fe (265.94–3599.60 mg/kg) and Zn (76.77–294.70 mg/kg) in all vegetables were above the recommended guideline level. Also, Zn (227.30–534.57 mg/kg) and Pb (101.53–407.58 mg/kg), in soil were above the recommended guideline level for soil. The results also showed not only the severity of heavy metal pollution of soil in the study area, but also risks that were deemed carcinogenic and noncarcinogenic to both adults and children as a result of consumption of vegetables from the study area. The hazard index for adults (0.46–41.156) and children (3.880–384.122), were high for all vegetables tested and are associated with cancer risk due to high Cr and Pb levels. The risk assessment showed that children may suffer more carcinogenic and noncarcinogenic health risk than adults. The study concluded that vegetables grown within the Korle lagoon's catchment is not suitable for consumption due to the associated adverse health effect.

Recent developments in ultrafiltration membrane technology for the removal of potentially toxic elements, and enhanced antifouling performance: A review

The presence of high concentrations of heavy metals (potentially toxic elements) in water bodies generates serious environmental issues and health problems that led to a dramatic increase in wastewater treatment costs. Therefore, it is imperative to develop low-cost and efficient technologies for removing these contaminants from wastewater. Membrane processes are advanced techniques for water treatment and ultrafiltration membrane (UF) has some advantages over other membranes as it requires low pressure to perform However, the UF membrane separates contaminants mainly by size exclusion mechanism, resulting in poor decontamination performance for potentially toxic elements and high susceptibility to membrane fouling. The performance of the UF membrane is often affected by organic and biofouling. Hence, researchers are still looking forward to developing new types of UF membranes that will make them more effective for potentially toxic elements removal and overcome the obstacle of fouling. This review aims to provide an overview of the application of UF membranes in potentially toxic element removal through bibliometric analysis and literature review. The incorporation of various organic, inorganic, carbon-based, and composite-based nano-materials into polymers such as zeolites, metal–organic frameworks (MOFs), and graphene oxide (GO) gave encouraging results for the removal of potentially toxic elements from water. Moreover, this review discusses the mechanisms of fouling in UF membranes and how different techniques can be used to control it. In the end, all the materials are evaluated and compared based on their efficiency, toxicity, simplicity in preparation, popularity, and cost efficiency to provide an overall critical view of the work done in this area. Also, the major challenges and limitations of the use of UF membranes are provided which will help to set the direction of future research.