High-temperature Synthesis Research Articles

Antibacterial activity and biocompatibility of titanium nickelide augments with the addition of silver nanoparticles for bone grafting: an experimental study

BACKGROUND: The relevance of this study was supported by the increasing number of infectious complications of bone augmentation in children and adults. Currently, porous titanium nickelide alloys are among the most preferred materials used in bone plasty. Despite the observable advantages of porous nickelide titanium alloys in terms of biochemical and biomechanical compatibility with the body, research on the antibacterial activity of alloys is ongoing to counter the development of infections at the implant–biological tissue border.
 AIM: To perform an experimental study of the biocompatible antibacterial surface in porous titanium nickelide alloys with the addition of silver nanoparticles.
 MATERIALS AND METHODS: Titanium nickelide alloys with 62% porosity were obtained using the self-propagating high-temperature synthesis method from nickel, titanium, and nanosilver powders at concentrations of 0.2 at.% Ag, 0.5 at.% Ag, and 1.0 at.% Ag, respectively. The experiment was conducted on nine sexually mature female white laboratory rats. They were divided into three groups, with three rats each. All animals were implanted with titanium nickelide along with porous granules of silver additives. The first group was the control, the second received 0.2 at.% silver, and the third received 0.5% silver. The standard method of incubating Staphylococcus epidermidis in liquid broth in the presence of the studied images was used to determine bactericidal activity, followed by seeding on solid media and counting colonies.
 RESULTS: The antibacterial effect of the samples on S. epidermidis gradually increased with increasing silver concentration. The significance of the differences between the experiment and control was confirmed by Student’s criterion p 0.005, whereas the sample without silver nanoparticles and the control do not differ significantly. Thus, these alloys may have bioactive properties because they contain silver nanoparticles. An alloy with a silver concentration of 0.5 at.% Ag showed the best antibacterial activity to S. epidermidis. In the clinical evaluation of the results of the experimental study, purulent inflammatory complications were not observed in all animals at all times. On day 75, the animals underwent computed tomography, which showed good occupancy of the bone defect and absence of a dystrophic effect on the area where the bone and soft tissue are in contact with the material.
 CONCLUSIONS: If the concentration of silver nanoparticles is increased up to 0.5 at%, the antibacterial activity and cytocompatibility of the implant also increase. Clinical experimental evaluation in all groups of animals showed that osteointegration of alloys with 0.5 at.% Ag begins immediately after implantation and is completed 2 weeks earlier than that in the remaining groups.

Self-propagating high-temperature synthesis of AlxCoCrFeNiMoy high-entropy alloys: thermochemical modelling, microstructural evaluation and high temperature oxidation behaviour

In this study, the feasibility of the synthesis of AlxCoCrFeNiMoy (0.5 < x < 3, y = 0.5,1) alloys via cost and energy efficient thermochemical modelling assisted (FactSage™) aluminothermic self-propagating high-temperature synthesis (SHS) method was investigated. In addition, selected SHS alloys were also suction-casted into a bar shape by using a vacuum arc melter and the microstructural changes and oxidation behaviour of selected alloys were investigated. The characterization results demonstrated that AlxCoCrFeNiMoy (0.5 < x < 3, y = 0.5,1) master alloys can be successfully synthesized via thermochemical modelling assisted SHS method with a substantial composition control. The microstructures of the SHS alloys were found to comprise of the FCC-A1, BCC (A2, B2) and σ phases with varying fractions depending on the composition. Increasing Al content was found to increase the hardness of the alloys from 278 HV to 829 HV for the AlxCoCrFeNiMo0.5 system. For AlxCoCrFeNiMo system, on the other hand, it had an increasing effect from Al0.5 to Al1.0 (from 659 HV to 903 HV) initially and then decreased the hardness to the levels of 773 HV with the further addition of Al. Suction-cast alloys exhibited rather similar microstructures with similar phase constituents and hardness values. As a general trend primer B2 phase fraction was increased due to higher cooling rate. Oxidation studies revealed that the Al3.0Mo0.5 alloy, which has higher B2 content (919 HV), exhibited better oxidation resistance after 100 h of exposure to air at 800 °C. Postulated scaling mechanisms, supported with the CALPHAD simulations and Raman analyses, revealed the formation of non-protective spinel oxides and sublimation of volatile MoOx oxides before the stabilization of a protective M2O3 (M = Al,Cr) layer, especially for the AlCoCrFeNiMo alloy.

Polyoxometallate Cluster Induced High-Entropy Oxide Sub-1 nm Nanosheets as Photoelectrocatalysts for Zn-Air Batteries.

The lack of highly efficient and inexpensive catalysts severely hinders the large-scale application of Zn-air batteries (ZABs). High-entropy oxides (HEOs) exhibit unique structures and attractive properties; thus, they are promising to be used in ZABs. However, conventional high-temperature synthesis methods tend to obtain microscale HEOs with a lower exposure rate of active sites. Here, we report a facile solvothermal strategy for preparing two-dimensional (2D) HEO sub-1 nm nanosheets (SNSs) induced by polyoxometalate (POM) clusters. Taking advantage of the special 2D sub-1 nm structure and precise element regulation, these 2D HEOs-POM SNSs exhibit enhanced bifunctional oxygen evolution and oxygen reduction reaction activity under light irradiation. Further applying these 2D HEOs-POM SNSs to ZABs as cathode catalysts, the CoFeNiMnCuZnOx-phosphomolybdic acid SNSs-based ZABs deliver a low charge/discharge voltage gap of 0.25 V at 2 mA cm-2 under light irradiation. Meanwhile, it could maintain an ultralong-term stability for 1600 h at 2 mA cm-2 and 930 h at 10 mA cm-2. The 2D sub-1 nm structure and fine element control in HEOs provide opportunities to solve the problems of low intrinsic activity, limited active sites, and instability of air cathodes in ZABs.

A Review of the State of Art of Fabrication Technologies of Titanium Aluminide (Ti-Al) Based on US Patents

This article evaluates the fabrication technologies of titanium aluminide (Ti-Al) and its practical applications by comparing it with the well-known Ti-Al binary phase diagram and US patents. Meanwhile, by analyzing and discussing the various patented Ti-Al fabrication technologies and applications, this article discusses the applications of Ti-Al-based alloys, mainly in the aircraft field. The improved fabrication processes and new application technologies are under patent protection. These technologies are classified into six categories: basic research on Ti-Al-based alloys, powder metallurgy of Ti-Al-based alloys, casting and melting of Ti-Al-based alloys, PM and AM manufacturing methods for aircraft applications, other fabrication technologies by Ti-Al-based alloys, and self-propagating high-temperature synthesis (SHS) of Ti-Al-based alloys. By comparing the principles and characteristics of the above techniques, the advantages, disadvantages, and application fields of each are analyzed and their developments are discussed. Based on the characteristics of Ti-Al, new fabrication and application technologies can be developed, which can overcome the existing disadvantages and be used to form new aircraft components.

Sorption of Radium-226 on Few-Layer Graphene Synthesized under Conditions of Self-Propagating High-Temperature Synthesis

Sorption of Radium-226 on Few-Layer Graphene Synthesized under Conditions of Self-Propagating High-Temperature Synthesis

Structural characteristics and properties of heat-resistant nickel β-alloys produced via the centrifugal SHS-casting method

Employing centrifugal self-propagating high-temperature synthesis (SHS) metallurgy, complemented by advanced metallurgical processes such as vacuum induction melting (VIM) and vacuum arc remelting (VAR), yielded the alloy formulation denoted as base–2.5Mo–1.5Re–1.5Ta–0.2Ti. This study investigates the effects of various technological modes and additional metallurgical treatments on the alloy's impurity and non-metallic inclusion content, structural characteristics, mechanical behavior under compression, and its oxidation mechanisms and kinetics when exposed to temperatures of 1150 °C for 30 h. With increasing centrifugal acceleration, the proportion of non-metallic inclusions (number of points) drops from 5 to 1–2 points. The best combination mechanical properties, including σucs = 1640 ± 20 MPa, σys = 1518 ± 10 MPa, and residual deformation were observed in alloys processed under conditions of increased gravitational force (g = 50). Within a centrifugal force range of g = 20÷300, the composition of the synthesis products aligned with the theoretical expectations. The total content of impurities is 0.15 ± 0.02 %, with a decrease in gas impurities–oxygen and nitrogen levels reduced to 0.018 % and 0.0011 %, respectively. The structural analysis of the alloys revealed the presence of globular and streaked inclusions of a chromium-based solid solution embedded within the matrix. Inclusions with thickness of 2–8 μm are present in the intergranular space: (Cr)Ni,Mo,Co, (Cr)Mo,Re and (Cr)Re,Mo. The formation of the Ni(Al,Ti) phase at grain boundaries was identified, contributing to an enhancement in plastic resistance and overall strength of the alloy. Oxidation mechanisms varied across different processing modes, with the size of structural components significantly influencing oxidation kinetics. The weight gain observed in SHS samples was 70 ± 10 g/m2 with oxidation predominantly occurring along the NiAl interphase boundaries and penetrating into the depth of the sample. TEM facilitated the identification of phases enriched with Ti microadditions, reducing the levels of dissolved nitrogen and oxygen within the intermetallic phase to a combined weight percentage (ΣO,N) of 0.0223 wt.%.

Effective incorporation of cobalt near surface region for cobalt-free cathodes in lithium-ion batteries

Cobalt-free cathode materials, particularly Ni-rich layered oxide cathode materials, are ideal for electric vehicle Li-ion batteries, offering high energy density and cost-effectiveness. However, high Ni content in high-temperature synthesis leads to issues like increased Li/Ni cation mixing and reduced rate capability, mainly due to the absence of Co. Therefore, this study investigated the utilization of a small amount of Co instead of completely removing it to enhance electrochemical performance. A simple pre-calcination process was used to induce Co substitution beneath the Ni-rich layered oxide cathode materials surface. A coating process was also performed for comparison. The Li/Ni cation mixing in the Co-substituted sample during high-temperature calcination was 2.43%, demonstrating a superior value compared to the Co-coating process. Rate capability tests showed superior performance for Co-substituted sample (164.2 mAh g−1) at 2 C compared to coated sample (151.0 mAh g−1). Moreover, Co substitution improved not only the cycle stability but also the high-temperature stability at an elevated state of charge.This study focuses on the surface modification of cobalt-free cathode, providing direct insight into the effects of Co substitution and typical Co coating and suggests an optimal process that uses small amounts of Co.

Intense thermal shock generators made of micron-thick SnO2 layers for the on-chip rapid thermal processing in air

Thermal shock-resistant heaters are essential in various electronic devices, including chemical sensors and pyroelectric electron emitters. The advent of ultrafast high-temperature sintering and shock synthesis of nanomaterials has increased the demand for air-operating high-rate joule heaters. Moreover, incorporating such heaters at the chip level would revolutionize current rapid thermal processing methods in semiconductor technology. Here, transparent micron-thick SnO2 resistors are grown by spray pyrolysis on alumina, silica, and oxidized silicon chips and used as thermal shock-resistant air-operating heaters. These heaters can generate repeated heating cycles at rates of 15,000 °C/s up to 900 °C/s. Tin is a group IV element and its impact on Si- and SiO2-based devices is minimal making the presented device silicon compatible. The superior performance of the presented heaters is attributed to the tin oxide’s unique combination of physicochemical properties including high-temperature chemical stability in oxidizing atmospheres, suitable intrinsic conductivity, and optimal negative temperature coefficient of resistance. The application of the SnO2 heaters for the rapid on-chip high-temperature oxidation and sintering of low-melting-point metal thin films, while preserving the metal layer’s nanotexture, is demonstrated.

Study of the structure and properties of interstitial alloys TixMo1 – xCyNz

Developing the new materials with improved properties suggests study of the crystal structure and properties of multicomponent interstitial alloys. We present the results of studying the crystal structure and microhardness of TixMo1 – xCyNz interstitial alloys in massive samples with different ratios of concentrations of constituent elements. The samples obtained by self-propagating high-temperature synthesis were subjected to homogenizing annealing at 2600 K for 8 h and cooled together with the furnace. Data of neutron diffraction revealed that the alloys have a face-centered cubic crystal structure in which Ti and Mo atoms, as well as C and N, are intersubstituted and statistically located in the 4b positions and octahedral 4a positions, respectively. The Rietveld method was used to determine crystallite sizes, dislocation densities, and microstrain using X-ray diffraction patterns. The microhardness of the samples was determined by the Vickers method. It is shown that the crystallite sizes determined by the Williamson-Hall and Scherrer methods differ significantly, whereas the patterns of crystallite growth in size, as well as regularities of changes in the dislocation density and microstrains follow change in the concentration of the components in the composition. As the carbon content in the alloy increases, the crystallite sizes and microstrains decrease, and the dislocation density increases. It is revealed that the smaller the crystallite size and the higher the dislocation density, the more microhardness is displaced towards increasing the carbon content. With a change in the ratio of components in TixMo1 – xCyNz as the crystallite size and microstrains decrease and dislocation density increases, the microhardness of the alloy increases by 1.5 – 2 times compared to binary carbide and titanium nitride. The results obtained can be applied to the use of interstitial alloys in instrumental and high-temperature engineering.

Determination of nitrogen in titanium, aluminum, silicon, hafnium nitrides and compositions on their base using a Metavak-AK analyzer

Methods for determining nitrogen in the products of self-propagating high-temperature synthesis (SHS), i.e., titanium, aluminum, silicon, and hafnium nitrides using a Metavak-AK gas analyzer have been developed. The optimal modes of analysis have been selected: the time and temperature of degassing of the crucible with flux in the furnace, the time and temperature of purging the extraction chamber with the sample, the time of automatic dumping of the sample from the loading chamber into the crucible, the time and temperature of purging the chamber after loading, the time of removal of gaseous products of reduction melting and registration of nitrogen signals. Furnace operating programs were compiled to determine the nitrogen content in TiN, AlN, Si3N4, HfN. Reduction melting of the samples took place in a helium flow at a furnace temperature of 2700°C for TiN, AlN, HfN, and 2500°C for Si3N4. To speed up the process and complete nitrogen extraction, a metal bath was used: nickel grit in the case of titanium and hafnium nitrides, and combined Sn/Ni flux for aluminum and silicon nitrides. The nitrogen content in the studied samples was determined in the range from 0.12 up to 39.3 %wt., the relative standard deviation was 0.6 – 3.6%. The accuracy of the results obtained on a Metavak-AK gas analyzer is confirmed by the Kjeldahl and Dumas reference methods.

Using the Spark Plasma Sintering System for Fabrication of Advanced Semiconductor Materials.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of an SPS device used for material processing and synthesis in both scientific and industrial applications and aims to present manufacturing methods and the versatility of an SPS device, presenting examples of processing Arc-Melted- (half-Heusler, cobalt triantimonide) and Self-propagating High-temperature Synthesis (SHS)-synthesized semiconductor (bismuth telluride) materials. The SPS system functionality development is presented, the purpose of which was to broaden the knowledge of the nature of SPS processes. This approach enabled the precise design of material sintering processes and also contributed to increasing the repeatability and accuracy of sintering conditions.

Refinement of the Manufacturing Route and Evaluation of the Reinforcement Effect of MAX Phases in Al Alloy Matrix Composite Materials

Microwave Assisted Self-propagating High-temperature Synthesis (MASHS) was used to prepare open-porous MAX phase preforms in Ti-Al-C and Ti-Si-C systems, which were further used as reinforcements for Al-Si matrix composite materials. The pretreatment of substrates was investigated to obtain open-porous cellular structures. Squeeze casting infiltration was chosen to be implemented as a method of composites manufacturing. Process parameters were adjusted in order to avoid oxidation during infiltration and to ensure the proper filling. Obtained materials were reproducible, well saturated and dense, without significant residual porosity or undesired interactions between the constituents. Based on this and the previous work of the authors, the reinforcement effect was characterized and compared for both systems. For the Al-Si+Ti-Al-C composite, an approx. 4-fold increase in hardness and instrumental Young's modulus was observed in relation to the matrix material. Compared to the matrix, Al-Si+Ti-Si-C composite improved more than 5-fold in hardness and almost 6-fold in Young's modulus. Wear resistance (established for different loads: 0.1, 0.2 and 0.5 MPa) for Al-Si+Ti-Al-C was two times higher than for the sole matrix, while for Al-Si+Ti-Si-C the improvement was up to 32%. Both composite materials exhibited approximately two times lower thermal expansion coefficients than the matrix, resulting in enhanced dimensional stability.

Boosting Thermoelectric Performance via Weakening Carrier-Phonon Coupling in BiCuSeO-Graphene Composites.

BiCuSeO is a promising oxygen-containing thermoelectric material due to its intrinsically low lattice thermal conductivity and excellent service stability. However, the low electrical conductivity limits its thermoelectric performance. Aliovalent element doping can significantly improve their carrier concentration, but it may also impact carrier mobility and thermal transport properties. Considering the influence of graphene on carrier-phonon decoupling, Bi0.88Pb0.06Ca0.06CuSeO (BPCCSO)-graphene composites are designed. For further practical application, a rapid preparation method is employed, taking less than 1h, which combines self-propagating high-temperature synthesis with spark plasma sintering. The incorporation of graphene simultaneously optimizes the electrical properties and thermal conductivity, yielding a high ratio of weighted mobility to lattice thermal conductivity (144 at 300K and 95 at 923K). Ultimately, BPCCSO-graphene composites achieve exceptional thermoelectric performance with a ZT value of 1.6 at 923K, bringing a ≈40% improvement over BPCCSO without graphene. This work further promotes the practical application of BiCuSeO-based materials and this facile and effective strategy can also be extended to other thermoelectric systems.

Preparation of High-Performance Mn-Doped SnTe Materials at High Pressure and High Temperature.

SnTe is an environmentally friendly medium-temperature thermoelectric material, but its inherent low power factor (PF) and high lattice thermal conductivity severely limit its application. In this study, based on the fact that Mn doping can induce band convergence, the high-pressure and high-temperature (HPHT) synthesis method was used to optimize the sample preparation and shorten the synthesis cycle to 30 min. The results show that the Sn0.93Mn0.10Te sample achieves the maximum PF value of 34.00 μW cm-1 K-2 at 775 K and PFave value of 21.36 μW cm-1 K-2 between 300-875 K. Microstructure analysis shows that the high-pressure synthesis method introduces abundant grain boundaries, various grain sizes, multiple defects, and pore structures into the sample. These microscopic crystal structures can effectively scatter phonons and lower the lattice thermal conductivity. The modification of these micromorphologies results in the Sn0.92Mn0.11Te sample attaining a minimum lattice thermal conductivity of 0.45 W m-1 K-1 at 625 K. The thermoelectric figure of merit (zT) of sample Sn0.92Mn0.11Te reaches a maximum value of 1.1 at 775 K, and the zTave reaches 0.63 in the range of 300-875 K. This study indicates that the synergistic effect of Mn element doping and microstructure modification can effectively optimize the thermoelectric transport performance of SnTe materials.

Stability and Physical Properties of Metastable Ba-Si Clathrates.

In the present study, we have investigated the stability of different Ba-Si clathrates with pressure and temperature using DFT calculations and studied the stability of type I Ba8Si46 and type IX Ba24Si100 clathrates using high pressure─high temperature synthesis technique, calorimetry, and diffraction experiments. When increasing pressure, the type I Ba8Si46 clathrate and BaSi6 become more stable. In good qualitative agreement with experiments, the type IX Ba24Si100 clathrate becomes stable at a pressure of 1-2 GPa thanks to the pressure and thermal effect of both electronic and vibrational contributions. One can notice that the presence of Ba in the cages of type IX clathrate increases significantly the stability and the mechanical properties of type IX clathrate. We have determined the P-T existence domain of type IX Ba24Si100 clathrate from ex situ experiments, which was confirmed by in situ synchrotron X-ray experiments. At room pressure and under an oxidizing atmosphere, the type I Ba8Si46 and the type IX Ba24Si100 clathrates are stable up to about 560 °C and up to about 600 °C, respectively. The thermoelectric properties of type IX Ba24Si100 are also reported.

ИССЛЕДОВАНИЕ ВЛИЯНИЯ ДОБАВКИ ВЫСОКОДИСПЕРСНОЙ ФАЗЫ КАРБИДА ТИТАНА, СИНТЕЗИРОВАННОЙ В РАСПЛАВЕ, И ТЕРМООБРАБОТКИ НА СТРУКТУРУ И СВОЙСТВА СПЛАВА АМ4,5Кд

The study results are given which are devoted to finding the effect of reinforcement with fine phase of titanium carbide in the amount of 10 masses% on the physico-mechanical and tribotechnical properties of industrial aluminum AM4.5Kd alloy. The physico-mechanical (density, porosity, coefficient of thermal linear expansion, hardness, microhardness) and tribotechnical (wear rate, friction factor, self-heating temperature) properties of the composite material AM4.5Kd-10%TiC obtained by self-propagating high-temperature synthesis before and after heat treatment are analyzed. It is found out that composite samples after heat treatment have a good combination of physical and mechanical properties, namely a low level of porosity, a low value of the coefficient of thermal linear expansion, and the values of hardness and microhardness are increased twice. Special attention should be paid to the fact that reinforcement with a ceramic phase in combination with heat treatment leads to a significant increase in the level of wear resistance of the matrix alloy (by 9 times) and a decrease in the friction factor (by 4 times). Thus, according to the results of the studies conducted, the resulting composite material AM4.5Kd-10%TiC can be recommended as a material used in tribological assemblies.

Porosity and phase composition effects on SHS-NiTi structure and mechanical properties

NiTi samples with 59–70% porosity were obtained by the self-propagating high-temperature synthesis (SHS) using Ti, Ni, and NiTi powders as inert. The maximum and average pore sizes increase, while the maximum and average dimensions of the bridges decrease with porosity, controlled by adjusting the amount of inert additives, based on the surface and cross-sectional microscopy studies. The phase composition of porous NiTi was determined by X-ray diffraction. The alloy contains an austenitic B2 TiNi phase, a martensitic B19′ TiNi phase, and a secondary Ti2Ni phase. SHS-NiTi samples with different porosity were tested by uniaxial compression, revealing mechanical properties’ dependence on porosity. It is shown that with an 11% increase in the NiTi alloy porosity, the yield and compressive strength are reduced by almost a factor of 2.

Improvement of thermoelectric properties of xNb:(1-x)SrTiO3 composite ceramics by high-pressure high-temperature synthesis

The high stability and low cost are considered comparative advantages of the SrTiO3 chalcogenide oxide thermoelectric material. However, the pure SrTiO3 material is characterized by low electrical conductivity and high thermal conductivity, which could eventually lead to poor overall thermoelectric performance, and limit its application in the field of high temperature thermoelectricity. The development of composite-based metal materials with SrTiO3 by using suitable methods is arising as the most promising approach to improve their electrical properties. Along these lines, in this work, xNb: (1-x) SrTiO3 composite ceramics were successfully synthesized by using the high temperature and high-pressure (HPHT) method. The Nb powder was oxidized into various niobium oxides exhibiting their own thermoelectric properties under HPHT conditions to optimize the thermoelectric properties of the Nb/SrTiO3 composites. From our analysis, it was demonstrated that with the increase of the Nb powder content, the electrical properties were significantly improved. In addition, the fabricated Nb/SrTiO3 composite ceramics possessed a special “pore” microstructure, which significantly reduced the thermal conductivity of the material. In this work, the physical phase, microscopic morphology, and thermoelectric properties of the synthesized samples were also systematically tested and analyzed, and the maximum zT value of 0.28@973 K was obtained for the final sample with x = 0.4. The implementation of the HPHT method for the preparation of chalcogenide oxide composite ceramics provides valuable insights for the improvement of their thermoelectric properties.

Effect of in vitro transcription conditions on yield of high quality messenger and self-amplifying RNA

Messenger RNA (mRNA) and self-amplifying RNA (saRNA) vaccines against SARS-CoV-2 produced using in vitro transcription (IVT) were clinically approved in 2020 and 2022, respectively. While the industrial production of mRNA using IVT has been extensively optimized, the optimal conditions for saRNA have been explored to a lesser extent. Most T7 polymerase IVT protocols have been specifically optimized for mRNA which is ∼5–10-fold smaller than saRNA and may have profound effects on both the quality and yield of longer transcripts. Here, we optimized IVT conditions for simultaneously increasing the yield of full-length transcripts and reducing dsRNA formation through Design of Experiments. Using a definitive screening approach, we found that the key parameters are temperature and magnesium in the outcome of RNA quality (% full length transcript) and yield in small scale synthesis. The most important parameter for reducing dsRNA formation for both mRNA and saRNA was Mg2+ concentration (10 mM). We observed that a lower temperature was vital for production of high quality saRNA transcripts. mRNA quality was optimal at higher Mg2+ concentration (>40 mM). High quality transcripts correspond to significantly reduced product yield for saRNA, but not for mRNA. The differences between mRNA and saRNA requirements for high quality product and the relationship between high quality large saRNA molecules and low temperature synthesis have not been reported previously. These findings are key for informing future IVT parameters design and optimization for smaller and larger RNA transcripts.

Synthesis, Structure, and Properties of 2O-BaPtO3, a Phase Derived from Hexagonal Perovskite.

We have made the compound 2O-BaPtO3 by high-pressure, high-temperature synthesis, determined its structure, and tested its catalytic activity. Compounds of the same stoichiometry have been reported and tentatively identified as hexagonal perovskites, and although no structural model was ever established, 2O-BaPtO3 is clearly different and, to the best of our knowledge, unique. It features continuous chains of face-sharing PtO6 octahedra, like the well-known 2H hexagonal perovskite type, but with a staggered offset between the chains that breaks hexagonal symmetry and disrupts the close-packed array of A = Ba and X = O that is a defining characteristic of ABX3 perovskites. We investigated this structure and its stability vs the conventional 2H form using X-ray and neutron diffraction, X-ray absorption spectroscopy, and ab initio calculations. Catalytic testing of 2O-BaPtO3 showed that it is active for hydrogen evolution.