High Surface Area Research Articles

Corn Husk Derived Activated Carbon/Siloxene Composite Electrodes based Symmetric Supercapacitor with High Energy Density and Wide Temperature Tolerance

AbstractIn the present work, novel composite material comprising of corn husk derived activated carbon and siloxene nanosheets have been explored as new class of multicomponent electrode material for fabricating high energy density supercapacitors with wide temperature tolerance. The activated carbon obtained from corn husk (ACH–900) with high surface area and pore volume acts as an ideal framework for hosting siloxene nanosheets (S) that allows the overall siloxene–corn husk derived activated carbon (ACH–900/S) composite to deliver excellent electrochemical performance. The as‐prepared ACH–900/S composite electrode exhibited a high specific capacitance of 415 F g−1 at 0.25 A g−1 and retained 73.4 % of its initial capacitance even at a high current density of 30 A g−1 in 1 M Na2SO4 electrolyte. In addition, the symmetric supercapacitor assembled with “acetonitrile/water‐in‐salt (AWIS)” electrolyte exhibited an energy density of 57.2 W h kg−1 at 338 W kg−1 with a cyclic stability of 92.8 % after 10000 cycles at 5 A g−1 current density. Besides, the fabricated ACH–900/S supercapacitor can operate over wide temperature range from 0 to 100 °C. This work opens up new frontiers to develop low‐cost safe supercapacitors with wide temperature tolerance and excellent electrochemical performance.

Data-Driven Radial Compressor Design Space Mapping

Abstract Estimates of turbomachinery performance trends inform system-level compromises during preliminary design. Existing empirical correlations for efficiency use limited experimental data, while analytical loss models require calibration to yield predictive results. From a set of 3708 radial compressor computations, this paper maps efficiency as a function of mean-line aerodynamics, and determines the governing loss mechanisms. An open-source turbomachinery design code creates annulus and blade geometry, then runs a Reynolds-averaged Navier–Stokes simulation for compressors sampled from the mean-line design space. Polynomial surface fits yield a continuous eight-dimensional representation of the design space for analysis, predicting efficiency with a root-mean-square error of 1.2% points. The results show a balance between surface dissipation in boundary layers and mixing loss due to casing separations sets optimum values for inlet Mach number, hub-to-tip ratio, de Haller number, and backsweep angle. Surface dissipation drives the effect of flow coefficient, with high surface areas at low values, and high velocities at high values. Compact compressor designs are achieved by increasing inlet Mach number, reducing hub-to-tip ratio, and minimizing the radial loading coefficient—all of which reduce efficiency approaching design space boundaries. An interactive web-based tool makes the results available to practising engineers, demonstrating large ensembles of automated designs and simulations as a higher-fidelity replacement for legacy empirical correlations in preliminary design.

Self-powered strain sensing devices with wireless transmission: DIW-printed conductive hydrogel electrodes featuring stretchable and self-healing properties

With rapid advancements in health and human–computer interaction, wearable electronic skins (e-skins) designed for application on the human body provide a platform for real-time detection of physiological signals. Wearable strain sensors, integral functional units within e-skins, can be integrated with Internet of Things (IoT) technology to broaden the applications for human body monitoring. A significant challenge lies in the reliance of most existing wearable strain sensors on rigid external power supplies, limiting their practical flexibility. In this study, we present an innovative strategy to fabricate glutaraldehyde (GA)-poly(vinyl alcohol) (PVA)/cellulose nanocrystals (CNC)/Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) conductive hydrogels through multiple hydrogen bonding systems. Combining the advantageous rheological properties of the precursor solution and the high specific surface area after freeze–thaw cycling, we have created a self-powered sensing system prepared by large-area printing using direct ink writing (DIW) printing. The resulting conductive hydrogel exhibits commendable mechanical properties (411 KPa), impressive stretchability (580 %), and robust self-healing capabilities (>98.3 %). The strain sensor, derived from the conductive hydrogel, demonstrates a gauge factor (GF) of 2.5 within a stretching range of 0–580 %. Additionally, the resultant supercapacitor displays a peak energy density of 0.131 mWh/cm3 at a power density of 3.6 mW/cm3. Benefiting from its elevated strain response and remarkable power density features, this self-powered strain sensing system enables the real-time monitoring of human joint motion. The incorporation of a 5G transmission module enhances its capabilities for remote data monitoring, thereby contributing to the progress of wireless tracking technologies for self-powered electronic skin.

Selective electrosorption of heavy metal ions from wastewater with S-doped hierarchical porous carbon derived from waste Camellia oleifera shell

Capacitive deionization (CDI) has garnered significant attention in desalination and the removal of heavy metal ions. The quest for cost-effective and high-performance electrode materials is crucial to advance CDI applications. Herein, we report a sulfur-doped hierarchical porous carbon (SPC) derived from waste camellia oleifera shells via a sustainable hydrothermal carbonization process followed by KOH/ammonium salt activation. The optimized SPC-0.2 exhibits exceptional characteristics, featuring a high specific surface area of 1875 m2 g−1 and substantial sulfur doping at 8.65 %, leading to enhanced specific capacitance (161.3 F g−1) in a 1 M NaCl solution. Under optimal operating conditions (1.2 V, 10 mL min−1, 500 mg L−1 NaCl), the SPC-0.2 electrode achieves a notable desalination capacity of 26.64 mg g−1. In particular, the electrode can selectively remove >99 % of Cr3+ and Cu2+ ions (each 10 mg L−1) in a 100 mg L−1 NaCl solution. This high selectivity is attributed to the formation of sulfides via low adsorption energies between the doped sulfur atoms and the targeted heavy metal ions. Furthermore, the SPC-0.2 electrode demonstrates robust reusability and high efficiency in the actual water body. Collectively, our findings underscore the significant potential of the synthesized SPC as an electrode material for CDI, particularly in the selective capacitive removal of heavy metal ions from wastewater. This work not only contributes to the circular economy by using waste biomass, but also offers a viable solution for environmental remediation.

Insight into the efficient loading and enhanced activity of enzymes immobilized on functionalized UiO-66

Enzyme immobilization is an effective strategy for achieving efficient and sustainable enzyme catalysis. As a kind of promising enzyme-loading materials, the systematic research on zirconium based metal organic frameworks (Zr-MOFs) about immobilization performance at molecular level is still in its initial stage. In this work, UiO-66 was functionalized with various groups (-H, -NH2, -COOH, -OH, -2OH) for the immobilization of cytochrome c (Cyt c) and antioxidant enzyme catalase (CAT). Then the effects of surface-functionalized UiO-66 derivatives on the loading efficiency, enzyme stability and catalysis kinetics were systematically investigated. In addition, the affinity constants of Cyt c and CAT towards UiO-66-series MOFs carriers were also compared. The results have shown that hydroxyl group functionalized UiO-66 represents the highest enzyme loading capacity, enhanced activity and improved stability for Cyt c and CAT possibly due to high surface area and suitable microenvironments as well as enhanced affinity towards the enzymes provided by the introduction of a single hydroxyl group. Our research would foresee immense potential of MOFs in engineering biocatalysts.

Defect-Induced Sensitivity Improvement in HfNBr Monolayers for Ammonia Detection.

Two-dimensional materials, owing to their unique physical properties and high surface area, play a crucial role in intelligent sensing, particularly in the domain of atmospheric pollutant monitoring. In this work, we have extensively investigated the gas-sensing capabilities of the HfNBr monolayer for ammonia detection by introducing point defects, utilizing density functional theory and nonequilibrium Green's function calculations. Upon the introduction of point defects, the adsorption energy of HfNBr monolayers for ammonia significantly increased (from -0.162 to -1.257 eV), indicating a markedly strengthened affinity. To further elucidate the sensing mechanism, we conducted an in-depth investigation into the charge transfer dynamics, the density of states, and the charge density difference between the adsorbent and the adsorbate. Besides, we employed the NEGF method to evaluate the changes in the current-voltage characteristics of the HfNBr monolayer before and after adsorption, which revealed a remarkable change in the apparent resistance, thereby demonstrating excellent sensitivity. The exceptional performance of the HfNBr monolayer toward NH3 demonstrates its significant value in practical applications for ammonia detection.

Advanced Diagnostic Techniques for Scrub Typhus: From Conventional Methods to Nanotechnology Solutions

AbstractScrub typhus is an acute illness caused by the bacteria Orientia tsutsugamushi and is transmitted by mites. Scrub typhus propagates via infected chigger bites (larval stage). Diagnosing scrub typhus is challenging due to its ability to mimic symptoms of other febrile illnesses. Conventional methods such as Weil‐Felix, ELISA, and PCR are available for diagnosing scrub typhus. The Weil‐Felix test was formerly used in developing nations to diagnose scrub typhus, but it is not recommended since it lacks both specificity and sensitivity. IFA and ELISA are superior for detecting scrub typhus; however, they are not as effective at detecting the illness in its early stages and require convalescent sampling to confirm positive samples. However, because the Orientia tsutsugamushi serotypes differ in their genetic makeup, PCR‐based approaches have become less applicable despite their higher specificity and sensitivity. Nanomaterial‐based biosensing could help detect scrub typhus early due to its high surface area, electrical conductance, and chemical stability. This study emphasizes the need for point‐of‐care detection of this under‐diagnosed but fatal disease, emphasizing the importance of nanobiosensors in early diagnosis. The pathophysiology of scrub typhus, standard diagnostic procedures, and the critical role that nanobiosensors play in the early detection of scrub typhus are discussed.

Scalable fabrication of high surface area g-C3N4 nanotubes for efficient photocatalytic hydrogen production

In this research, we present a novel facile, scalable, and template-free technique of synthesizing graphitic carbon nitride (g-C3N4) nanotubes for generating hydrogen through photocatalysis. The hybrid technique involves a two-fold mixing of the precursor materials melamine (M) and cyanuric acid (CA), involving ball milling followed by solution mixing. By varying the M:CA molar ratios, different compositions of g-C3N4 nanotubes were fabricated. The study focused on examining the surface characteristics and the photocatalytic hydrogen evolution performance of these nanotubes. Nanotubes with high specific surface area of 206 m2 g−1 for M:CA molar ratio of 1:3 and 178 m2 g−1 for M:CA molar ratio of 1:5 were produced, with H2 evolution rates of 543 μmol h−1 g−1 and 740 μmol h−1 g−1 respectively, which were an increase of 4 and 5-fold, respectively, in comparison to the pristine sample. The enhanced efficiency of hydrogen production through photocatalysis by nanotubes, when contrasted with pristine material, can be ascribed to their high crystallinity, superior specific surface areas, decreased recombination rates of electron-hole pairs generated during light exposure, and improved dynamics of charge carriers. This hybrid technique provides a new pathway for cost-effective fabrication of g-C3N4 nanotubes with substantial surface areas and high yield photocatalysts on an industrial scale, without the use of templates and hydrothermal processes for efficient hydrogen generation.

Removal of Remazol Red Dyes Using Zeolites-Loaded Nanofibre Coated on Fabric Substrates

Nanofibre-based membranes have shown great potential for removing textile wastewater due to their high porosity and surface area. However, nanofibre membranes exhibit lower dye removal efficiency. Hence, this study aims to improve the dye removal performance of nanofibre membranes by incorporating zeolites. The research involved fabricating composite membranes by electrospinning polyvinyl alcohol (PVA) nanofibres incorporated with zeolites. Mechanical strength was enhanced by placing the PVA/zeolite nanofibre membrane between fusible nonwoven interfacing and woven polyester fabric, followed by heat treatment. Morphological analysis revealed the uniform dispersion of zeolite particles within the PVA nanofibres. EDX analysis confirmed the successful incorporation of zeolites into the fibres. Among all membrane samples, the PZ-0.75 membrane exhibited the highest pure water flux (PWF) with approximately 1358.57 L·m−2·min−1 for distilled water and 499.85 L·m−2·min−1 for batik wastewater. Turbidity of batik wastewater increased proportionally with zeolite concentration, with removal rates of 84.79%, 78.8%, 76.96%, and 74.19% for PZ-0.75, PZ-0.5, PZ-0.25, and PVA membranes, respectively. Furthermore, the UV/Vis spectrophotometer demonstrated that dye removal efficiency increased from 2.22% to 8.89% as the zeolite concentration increased from 0% to 0.75%. In addition, the PZ-0.75 membrane effectively removed RR dye at a concentration of 1 mg/L, with an optimal contact time of approximately 60 min. The adsorption mechanism of the PZ-0.75 membrane aligns with the Freundlich model, with an R2 value of 0.983. Overall, this study demonstrates the efficiency of zeolite in the fabric substrates to improve the filtration and adsorption properties for wastewater treatment, particularly in textile industries.

Experimental investigation of performance, emission, and combustion characteristics of a diesel engine using blends of waste cooking oil-ethanol biodiesel with MWCNT nanoparticles

In this study, blends of 5 % and 10 % ethanol with waste cooking oil biodiesel are mixed with Multi-Walled Carbon Nanotubes (MWCNT) at a concentration of 30 ppm. MWCNTs, known for their high surface area and unique properties, are added to potentially enhance combustion efficiency and reduce emissions. These blends are then tested in a diesel engine to evaluate their performance, emission and combustion characteristics using Design of experiment technique. After conducting various experiments and analyses, the blend of 20 % biodiesel, 10 % ethanol, and 30 ppm MWCNT was identified as the most optimal due to its favorable engine characteristics. Brake Thermal Efficiency (BTE) was increased from 3.1 % to 3.4 % with the addition of MWCNTs, indicating enhanced fuel efficiency. Moreover, average Fuel Consumption is decreased from 2.2 % to 2.5 %, suggesting improved fuel utilization. Using MWCNT 30 ppm in B20 ethanol blends (MWCNT 30 ppm B20+E10) resulted in 35 % reduction in nitrogen oxide (NOx) emissions, 37 % reduction in CO emissions and 39 % reduction in HC emissions. Hence MWCNTs demonstrated effectiveness in mitigating harmful exhaust emissions The optimized values for all parameters fall within acceptable ranges, indicated successful optimization using Response surface methodology. Additionally, statistical analysis reveals that the machine learning- XGBoost model outperformed all other advanced machine learning models across all tested metrics, including MSE, MAE, and R-square.

Emerging Capacitive Materials for On-Chip Electronics Energy Storage Technologies

Miniaturized energy storage devices, such as electrostatic nanocapacitors and electrochemical micro-supercapacitors (MSCs), are important components in on-chip energy supply systems, facilitating the development of autonomous microelectronic devices with enhanced performance and efficiency. The performance of the on-chip energy storage devices heavily relies on the electrode materials, necessitating continuous advancements in material design and synthesis. This review provides an overview of recent developments in electrode materials for on-chip MSCs and electrostatic (micro-/nano-) capacitors, focusing on enhancing energy density, power density, and device stability. The review begins by discussing the fundamental requirements for electrode materials in MSCs, including high specific surface area, good conductivity, and excellent electrochemical stability. Subsequently, various categories of electrode materials are evaluated in terms of their charge storage mechanisms, electrochemical performance, and compatibility with on-chip fabrication processes. Furthermore, recent strategies to enhance the performance of electrode materials are discussed, including nanostructuring, doping, heteroatom incorporation, hybridization with other capacitive materials, and electrode configurations.

Production of hydrochar from the hydrothermal carbonisation of food waste feedstock for use as an adsorbent in removal of heavy metals from water

AbstractIn this research, discarded butternut peels were converted into hydrochar products through hydrothermal carbonisation (HTC), with adjustments made to the temperature (ranging from 180 to 260℃) and residence time (spanning 45–180 min). The findings indicated that both the temperature and time of carbonisation significantly influenced the yield of hydrochar (HC), as well as its physiochemical and structural properties. Higher temperatures and prolonged residence time led to decreased yield, elevated fixed carbon content and an increased fuel ratio. Furthermore, raising the process conditions increased HHV and reduced the oxygen-containing functional groups. The HC yield dropped from 28.75 to 17.58% with increased carbonisation temperature and time. The findings of this study also suggest that modified hydrochar is a promising material for removing heavy metals from wastewater. It is a relatively low-cost and abundant material that can be produced from various biomass feedstocks, including food waste. In addition, it is a sustainable and environmentally friendly option for wastewater treatment. Hydrochar-based systems offer several advantages over traditional methods of heavy metal removal, such as chemical precipitation and ion exchange. The unique physicochemical characteristics of hydrochar, including its porous structure and oxygen-rich functional groups, offer a high surface area and more binding sites for heavy metal ions. By changing the physicochemical properties of hydrochar with chemicals like phosphoric acid, it is possible to increase its adsorption capacity. The Freundlich isotherm was the best fit for the adsorption data for all three metal ions (Pb2+, Cu2+ and Cd2+), indicating that the adsorption process is multilayer and heterogeneous.

Modulating pro-fibrotic macrophages using yeast beta-glucan microparticles prepared by Pressurized Gas eXpanded liquid (PGX) Technology®

Pro-fibrotic M2-like macrophages are widely implicated in the pathogenesis and progression of lung fibrosis due to their production of pro-fibrotic growth factors and cytokines. Yeast beta-glucan (YBG) microparticles have shown potential as immunomodulators that can convert macrophage polarization from a pro-fibrotic phenotype to an anti-fibrotic phenotype through the engagement of the Dectin-1 receptor. However, the processing conditions used to fabricate YBG microparticles can lead to unpredictable immunomodulatory effects. Herein, we report the use of Pressurized Gas eXpanded liquids (PGX) Technology® to fabricate YBG (PGX-YBG) microparticles with higher surface areas, lower densities, and smaller and more uniform size distributions compared to commercially available spray-dried YBGs. PGX-YBG is shown to activate Dectin-1 more efficiently in vitro while avoiding significant TLR 2/4 activation. Furthermore, PGX-YBG microparticles effectively modulate M2-like fibrosis-inducing murine and human macrophages into fibrosis-suppressing macrophages both in vitro as well as in ex vivo precision-cut murine lung slices, suggesting their potential utility as a therapeutic for addressing a broad spectrum of fibrotic end-point lung diseases.

Synthesis and characterization of bentonite-based NiO nanoparticles as bi-functional heterogeneous catalyst for efficient synthesis of 1,8-dioxo-decahydroacridines

A straightforward, expeditious, robust, and efficient synthesis of NiO@Bentonite nanocatalyst was done using a simple microwave method. The X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX), Brunauer–Emmett–Teller (BET), thermal behavior analysis, and vibrating sample magnetometer (VSM) techniques were used to characterize the physicochemical properties of the NiO@Bentonite nanocomposites. The outcomes demonstrated that the NiO nanoparticles are evenly distributed throughout the Bentonite surface and that the NiO@Bentonite nanocomposites have a high specific surface area and rich pore structure. The following report details the investigation of this catalyst for the preparation of 1, 8-dioxodecahydroacridine heterocycles in a one-pot, three-component reaction of aromatic aldehydes, dimedone, and aniline. After the conditions were optimized, the results demonstrated that this reaction could be carried out in an aqueous medium with a good yield.

Investigating the radical properties of oxidized carbon materials under photo-irradiation: behavior of carbon radicals and their application in catalytic reactions.

Oxidized carbon materials have abundant surface functional groups and customizable properties, making them an excellent platform for generating radicals. Unlike reactive oxygen species such as hydroxide or superoxide radicals that have been reported previously, oxidized carbon also produces stable carbon radicals under photo-irradiation. This has been confirmed through electron spin resonance. Among the various oxidized carbon materials synthesized, graphene oxide shows the largest number of carbon radicals when exposed to blue LED light. The light absorption capacity, high surface area, and unique structural characteristics of oxidized carbon materials offer a unique function for radical-mediated oxidative reactions.

Multiple applications of metal-organic frameworks (MOFs) in the treatment of orthopedic diseases.

Pharmacologic treatment of orthopedic diseases is a common challenge for clinical orthopedic surgeons, and as an important step in the stepwise treatment of orthopedic diseases, it is often difficult to achieve satisfactory results with existing pharmacologic treatments. Therefore, it is increasingly important to find new ways to effectively improve the treatment pattern of orthopedic diseases as well as to enhance the therapeutic efficacy. It has been found that metal-organic frameworks (MOFs) possess the advantages of high specific surface area, high porosity, chemical stability, tunability of structure and biocompatibility. Therefore, MOFs are expected to improve the conventional traditional treatment modality for bone diseases. This manuscript reviewed the applications of MOFs in the treatment of common clinical bone diseases and look forward to its future development.

N/O Co-doped Porous Carbon with Controllable Porosity Synthesized via an All-in-One Step Method for a High-Rate-Performance Supercapacitor.

A green and economical methodology to fabricate carbon-based materials with suitable pore size distributions is needed to achieve rapid electrolyte diffusion and improve the performance of supercapacitors. Here, a method combining in situ templates with self-activation and self-doping is proposed. By variation of the molar ratio of magnesium folate and potassium folate, the pore size distribution was effectively adjusted. The optimal carbon materials (Kx) have a high specific surface area (1021-1676 m2 g-1) and hierarchical pore structure, which significantly promotes its excellent capacitive properties. Notably, K2 shows an excellent mass specific capacitance of 233 F g-1 at 0.1 A g-1. It still retained 113 F g-1 at 55 A g-1. The assembled symmetric supercapacitor exhibited an outstanding cyclic stability. It maintains 100% capacitance after 100 000 cycles at 10 A g-1. The symmetric supercapacitor demonstrated a maximum power density of 99.8 kW kg-1. This study focuses on the preparation of layered pore structures to provide insights into the sustainable design of carbon materials.

Fabrication of MIL-101(Fe)-embedded biopolymeric films and their biomedical applications

AbstractThe development of wound-dressing materials with superior therapeutic effects, controlled bioactive agent release, and optimal mechanical properties is crucial in healthcare. This study introduces innovative hydrogel films designed for the sustained release of the local anesthetic drug Procaine (PC), triggered by pH changes. These films are composed of MIL-101(Fe) particles and pectin polymers. MIL-101(Fe) was chosen for its high surface area, stability in aqueous environments, and biocompatibility, ensuring low toxicity to normal cells. MIL-101(Fe)-embedded-pectin hydrogels were synthesized and characterized using Fourier-transformed infrared (FTIR) spectroscopy, thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD), inductively coupled plasma (ICP) spectrometry, particle size analysis, and goniometry. Rheological analysis assessed the hydrogels’ viscoelastic behavior, and UV-spectrophotometry was utilized for drug loading and release studies. The hydrogels exhibited shear-thinning properties, enhancing shape adaptability and recovery, crucial for wound-dressing applications. Controlled drug release was achieved by maintaining the PC solution’s pH between 8.2 and 9.8 during the drug-loading step. The hydrogel film’s impact on wound healing was evaluated through an in vitro wound healing assay, and cytotoxicity was assessed using a WST-1 cell proliferation assay with human dermal fibroblast cells. Results demonstrated that pectin composites enhance cell viability and support fibroblast cell migration without adverse effects, indicating their potential for effective wound healing applications. This study highlights the potential of MIL-101(Fe)-embedded-pectin hydrogels in advancing wound care technology. Graphical Abstract MIL-101(Fe)-embedded pectin film as wound dressing

Synergetic Combination of Carbon Xerogels, Graphene Oxide and nano‐ZnO for Aqueous and Organic Supercapacitors

Three‐dimensional carbon xerogels were synthesised via a facile approach that included the use of ZnO nanostructures both as a templating agent and as a catalyst for resorcinol–formaldehyde resin polymerisation simultaneously. Graphene oxide (GO) served as a stabilising agent during the drying and pyrolysis processes, avoiding the collapse of structure and improving the area surface. The method enabled the asobtained materials to possess optimised 3D porous structures for energy‐storage devices, such as wires or spaghetti‐like structures. Also, a high BET surface area was obtained (1661 m2•g−1) without using an additional activating agent. This great surface area improved the specific capacitance compared to materials without GO (358.1 F•g−1 vs 170.4 F•g−1). The carbon‐containing devices derived from resorcinolformaldehyde resin, GO, and Zn oxide showed better performance than the devices without GO. In particular, the sample that contained 2.5% of GO in the synthesis showed a specific capacitance of 166.6 F•g−1 at 0.5 A•g−1 and remained at ∼120 F•g−1 at 5 A•g−1. Also, it showed interesting energy density values at 0.5 A•g−1 (14.8 Wh•kg−1) and a power density of 200.7 W•kg−1. This reveals that the synthesis process made it possible to obtain composite materials with large surface areas without using a supercritical drying process.

Balancing volumetric and gravimetric capacity for hydrogen in supramolecular crystals.

The storage of hydrogen is key to its applications. Developing adsorbent materials with high volumetric and gravimetric storage capacities, both of which are essential for the efficient use of hydrogen as a fuel, is challenging. Here we report a controlled catenation strategy in hydrogen-bonded organic frameworks (RP-H100 and RP-H101) that depends on multiple hydrogen bonds to guide catenation in a point-contact manner, resulting in high volumetric and gravimetric surface areas, robustness and ideal pore diameters (~1.2-1.9 nm) for hydrogen storage. This approach involves assembling nine imidazole-annulated triptycene hexaacids into a secondary hexagonal superstructure containing three open channels through which seven of the hexagons interpenetrate to form a seven-fold catenated superstructure. RP-H101 exhibits high deliverable volumetric (53.7 g l-1) and gravimetric (9.3 wt%) capacities for hydrogen under a combined temperature and pressure swing (77 K/100 bar → 160 K/5 bar). This work illustrates the virtues of supramolecular crystals as promising candidates for hydrogen storage.