High Absorption Rate Research Articles

Spatiotemporal Absorption Features of Yellow Willow Water Usage on the Southern Edge of the Semi-Arid Hunshandak Sandland in China

The improvement of water usage efficiency and productivity, as well as the development of effective water management plans, necessitates a comprehensive understanding of how water utilization patterns in different soil layers within arid and semi-arid climates impact the capacity of plant roots to absorb water. However, there is currently no knowledge regarding the water use strategies employed by artificial yellow willow. So, we conducted a study on the hydrogen and oxygen isotopic composition of rainfall in yellow willow (Salix gordejevii) from the semi-arid region located at the southern edge of the Hunshandak Sandland in China. This study utilized measured data on xylem water, groundwater, soil moisture, and rainfall. By employing a combination of the direct comparison method and the MixSIAR model, we investigated the water uptake strategies employed by yellow willow throughout its growing season. The findings revealed that the mean δ D was highest in precipitation and lowest in groundwater, whereas the mean δ18O was highest in stem water and lowest in groundwater. The δ D and δ18O fluctuated significantly in precipitation but were steady in groundwater. Because precipitation was significantly less than evaporation, the slope and intercept were lower for the local than global atmospheric precipitation line. Water availability steadily declined with increasing depth. Lower δ18O values were caused by precipitation diluting the soil water. The MixSIAR results indicated that the primary source in May, September, and October was utilized at 19%, 18%, and 18%, respectively. In contrast, the utilization rate of each source varied considerably in June, July, and August (the primary source was utilized at 19%, 18%, and 18%, respectively). Comparatively high rates of water absorption and utilization were observed in June (19% of the total water source), July (18%), and August (23%). Therefore, the vertical distribution of the root system and variations in the soil water content regulate water usage for the yellow willow. To prevent excessive water usage and promote ecosystem restoration with artificial yellow willow plantations in water-limited desert settings, policy makers should consider the patterns of plant water use and soil water availability. By selecting drought-adapted plant species and optimizing irrigation management, it is possible to reduce water wastage and ensure that water is used efficiently for revegetation and ecosystem restoration, avoiding overuse of water and maintaining the sustainability of revegetation in water-stressed desert areas.

First-principles calculations to investigate impact of doping by chalcogen elements on the electronic, structural, and optical properties of SrTiO3 compounds

Doping techniques are commonly utilized to effectively modify the physical properties of a desired compound. In this study, we employed the first-principles DFT calculations with a GGA + TB-mBJ approach as implemented by the Wien2k code, by investigating the effects of oxygen group element concentrations on the structural, electronic, and optical properties of the perovskite substance SrTiO3. We calculated the formation energies of each doped structure to assess the viability of synthesis. The band gap is equal to 1.355 eV, 0.653 eV, and 0.632 eV for 12.5 % S, Se, and Te doped SrTiO3, respectively. For the pure SrTiO3, the band gap is 2.584 eV. According to our findings, raising the chalcogen concentrations resulted in a considerable decrease in band gaps and an improvement in the ability to absorb light in the visible range (380–790 nm), exceeding 105 cm−1 for Te doped SrTiO3 (STO). At zero frequency, the dielectric constant was found (ε1 (0)) to be 4.432 for SrTiO3 pure and 6.332 for SrTiO3 doped with Te (12.5 %) in GGA-PBE and (ε1 (0)) = 4.432 and 12.217 for GGA + mBJ. The optical conductivity of SrTO3 doped with Te is determined to be 0.322 * 104 /Ω.cm, in comparison to a value of 0.377 * 104/Ω.cm for mBJ. Our research revealed that raising the chalcogen concentrations significantly enhanced the electrical conductivity, as predicted, along with improvements in optical conductivity and reflectivity. SrTiO3-xYx (Y = S, Se, or Te) represents one of our quaternary alloys, demonstrating substantial potential as a promising material for advanced photovoltaic and solar cell applications. Our findings revealed that the doped materials exhibited significantly high absorption rates and productivity. We also examined additional optical parameters, including optical band gap, Urbach energy, and optical conductivity.

Soft and flexible polyvinyl alcohol/pullulan aerogels with fast and high water absorption capacity for facial mask substrates

Facial mask substrates commonly used in skincare are often considered unhealthy and environmentally unfriendly due to their composition of premoistened nonwovens containing various preservatives. This study aims to address this issue by developing a preservative-free degradable aerogel made from polyvinyl alcohol (PVA)/pullulan (PUL) using a unidirectional freeze-drying method. The aerogels had ordered three-dimensional porous structures and exhibited desirable mechanical properties. They were soft and flexible in both dry and wet states, and their Young's moduli were comparable to that of human skin. The aerogels had high porosity, ranging from 93.0 % to 95.1 %, and exhibited a high water absorption rate and water absorption capacity (ranging from 7.5 g/g to 10.1 g/g). After 30 min of water evaporation, the aerogels showed excellent moisture retention, ranging from 88 % to 93 %. Additionally, the PVA/PUL aerogel efficiently loaded and released active ingredients, such as rapidly releasing ascorbic acid (> 90 % within 30 min). These findings suggest that the PVA/PUL aerogel has potential as a material for facial mask substrates.

(005) Can Novel SDS-089 Nasal Vardenafil Spray Solution Achieve Satisfactory Drug Plasma Level Similar to Oral Vardenafil Formulation? A Bioanalysis Study Comparing Vardenafil Nasal vs Oral Formulations Using Liquid Chromatography Tandem Mass Spectrometry

Abstract Introduction The nasal drug delivery system offers many advantages when compared with oral administration, such as a faster onset of action, easily accessible, less drug degradation, and a high rate of absorption. The SDS-089 nasal Vardenafil (VDF) solution is a unique drug formulation designed to be delivered as a spray formulation. Objective To assess the bioavailability of SDS-089 nasal Vardenafil solution in human plasma levels using Liquid Chromatography Tandem Mass Spectrometry analysis. Methods The SDS-089 Vardenafil HCl formulation was prepared with the active pharmaceutical ingredient to the United States Pharmacopeia (USP) standard (batch 1704002361). The SDS-089 nasal spray solution was filtered (0.22 μm filter) and fitted with a nasal spray device to deliver 100 μL per spray which is equivalent to 2 mg Vardenafil HCl alcoholic solution per spray. This study received approval from the Institutional Review Board and Biosafety Committee (FB18/IRB/099). Blood samples from participants were collected at time 0 (pre-dose) and across different time intervals up to 10 hours and analyzed using Liquid Chromatography Tandem Mass Spectrometry (LC/MS) to quantify the level of Vardenafil and the internal standard. This protocol allows for the preparation and analysis of human samples, quality controls (QC), standard curve preparation, and instrumental analysis. During the validation experiments, each calibration standard and QC sample was prepared by spiking a specified amount of Vardenafil in human plasma with oral Vardenafil drug served as the internal standard for comparison. The concentration of analytes in each standard was quantified using LC/MS and detected using multiple-reaction monitoring for each of the respective analytes. The lower limit of quantitation (LLOQ) was defined as the lowest concentration that could be quantified with accuracy and precision within 20%, as calculated from chromatograms for the independent samples. Intra- and inter-run accuracy and precision were calculated for the three QC samples, and independent triplicate measurements with best-fit lines were selected using a linear regression model with a 1/x2 weighting factor in the calibration curves. Results The SDS-089 nasal Vardenafil solution showed excellent accuracy (mean 100, Standard Deviation, SD 4.1, % Relative Standard Deviation, RSD of 4%) and good precision (mean 50.1, SD 2.1, %RSD of 4%) on high (50ng/ml) QC assay tests. Similarly, the stability of QC on high (50ng/ml) plasma assay tests showed excellent accuracy (mean 100.8, SD 3.7, %RSD of 4%) and good precision (mean 50.4, SD 1.8, %RSD of 4%) on high (50ng/ml). Comparison between pharmacokinetic parameters of Vardenafil SDS-089 nasal spray (4mg) and oral tablet (10mg) showed T1/2 (2.52±0.99 vs 2.46±0.73 hour), Tmax (0.17±0.54 vs 0.97±0.35 hour), Cmax (time concentrations) (9.21±4.11 vs 11.24±7.83 ng/mL) and AUC0-inf (area under the curve from zero to infinity) (21.03±12.54 vs 37.25±41.51 ng/mL*h) (see Table 1: Pharmacokinetic parameters of Vardenafil HCI as SDS-089 nasal spray vs. oral tablet using non-compartmental analysis WinNonlin software). Conclusions SDS-089 nasal formulation appeared to deliver a high plasma concentration level of Vardenafil drug based on pharmacokinetic LC/MS data analysis with robust accuracy and precision. Disclosure Yes, this is sponsored by industry/sponsor: LTR Pharma Clarification: Industry funding only - investigator initiated and executed study

Excellent iron-chelating capacity of Yesso scallop (Patinopecten yessoensis) skirt hydrolysate fermented by Bacillus subtilis M17-b7

Peptide ferrous chelate is a new type of biological iron, which has the advantages of high absorption rate, safety and no digestive tract irritation. In this study, microbial fermentation was used for the first time to prepare iron-chelating peptides. Forty-eight strains were applied to ferment scallop skirts. A dominating strain was eliminated by using the iron binding capacity of the scallop skirt hydrolysate as the screening index. The scallop skirt hydrolysate fermented by Bacillus subtilis M17-b7 showed excellent iron-chelating capacity (96.20% ± 0.03%). Meanwhile, the structure, morphology and bioactivity of fermented scallop skirt hydrolysate (FSH) and fermented scallop skirt hydrolysate-iron (FSH–Fe) were measured. Based on the amino acid composition and spectral analysis, it was confirmed that the significant amino acids contains carboxyl, carbonyl, and amino groups. The result of scanning electron microscope indicated that the surface of FSH became porous and the particles were bigger after chelating with ferrous. Moreover, the peptide-ferrous chelate was more stable in salt solutions and simulated gastric juice compared with ferrous sulfate. It is also noteworthy that the preparation of ferrous chelate peptides by fermentation is cost-effective compared with enzymatic hydrolysis. Therefore, this study provides theoretical support for the use of fermentation as a promising tool to produce peptide-ferrous chelate.

Uncovering origin of grain boundary resistance to irradiation damage in NiCoCr multi-principal element alloys

Multi-principal element alloys (MPEAs) demonstrate significant promise as structural materials for nuclear energy equipment owing to their exceptional mechanical properties and radiation-resistant performances. In these alloys, the grain boundary (GB) serves as a crucial microstructure that typically mitigates irradiation damage by absorbing the irradiation-induced defect. However, the micromechanisms governing the anti-irradiation performance of GBs in MPEAs remain unclear. In this study, we investigate the irradiation defect production during collision cascade in the model NiCoCr bicrystal system through atomic simulations, aiming to unveil the atomic-scale origin of GB to resist irradiation damage in MPEAs. The results reveal that GBs effectively serve as sinks for irradiation defects in NiCoCr. The sink efficiency depends on the GB energetic state, including GB excess energy and defect segregation energy, as well as the energetic difference between interstitial and vacancy segregation. Statistical analysis identifies a universally exponent function between the defect absorption rate at GB and GB energetic state. In NiCoCr, the GB-disorder-induced-entropy increase leads to a biased reduction in interstitial segregation energy, narrowing the gap between interstitial and vacancy segregation energies by approximately 11 % compared to Ni. This improvement enhances the overall resistance of GBs to irradiation damage. Additionally, preferential segregation of Ni interstitial atoms is notably enhanced in NiCoCr, contributing to a high defect absorption rate at GBs. This study provides new insights into the resistance of GBs to irradiation defects in MPEAs and suggests GB engineering as an effective strategy for developing advanced alloys with enhanced radiation tolerance.

SME-MFP: A novel spatiotemporal neural network with multiangle initialization embedding toward multifunctional peptides prediction

As a promising alternative to conventional antibiotic drugs in the biomedical field, functional peptide has been widely used in disease treatment owing to its low toxicity, high absorption rate, and biological activity. Recently, several machine learning methods have been developed for functional peptide prediction. However, the main research heavily relies on statistical features and few consider multifunctional peptide identification. So, we propose SME-MFP, a novel predictor in the imbalanced multi-label functional peptide datasets. First, we employ physicochemical and evolutionary information to represent the peptide sequence’s initialization features from multiple perspectives. Second, the features are fused and then put into spatial feature extractors, where the residual connection and multiscale convolutional neural network extract more discriminative features of different lengths’ peptide sequences. Besides, we also design AFT-based temporal feature extractors to fully capture the global interactions of the sequences. Finally, devising a new loss to replace the traditional cross entropy loss to settle the class imbalance problems. The results show that our framework not only enhances the model's ability to capture sequence features effectively, but also accuracy improves by 3.89% over existing methods on public peptide datasets.

An effective material for solar steam generation applications: Gradient graphene sponge

The efficient use of solar energy for clean water is a renewable and environmentally-friendly route to solve global water scarcity. For this, we report the preparation of light, mechanically durable, and effective photothermal material. A simple acid impregnation method was applied to graphene sponge material (GSM) possessing hydrophobic character to gain partial hydrophilicity to obtain a gradient structure. The morphological and structural properties of the gradient graphene sponge material (GGSM) were carried out using scanning electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, X-ray powder diffraction patterns, Fourier-transformed infrared spectroscopy, and water drop contact angle measurements. GGSM showed fast and effective water vapor conversion performance due to the gradient structure, as well as the high rate of sunlight absorption and photothermal conversion thanks to graphene. With the advantageous feature of gradient structure, GGSM achieved a high water vapor conversion capacity (1.79 kg/m2h) and solar thermal efficiency of 57% compared to GSM (1.58 kg/m2h; 45%). This new material provides a novel approach to solar energy applications.

Ecological risk assessment of potentially toxic elements (PTEs) in agricultural soil, vegetables and fruits with respect to distance gradient in proximity to lead-acid battery industry

Lead-acid battery industries in Bangladesh have proliferated in urban areas, leading to the release of significant amounts of potentially toxic elements (PTEs) and metalloids into the environment. This study aimed to assess the spatial distribution, sources, contamination status, and ecological risks in agricultural soils, vegetables, and fruits near these industries. Soil samples were collected from four sites at varying distances (0 m, 100 m, 250 m, and 500 m) around three lead-acid battery industries (AA, AB, and AC) in Dhaka and Gazipur Districts during June-July 2020. The concentrations of the Pb, As, Cd and Zn in agricultural soils were ranged between 8.40–116.61, 8.99–28.21, 0.03–1.28, and 25.38–68.72 mg/kg, respectively. The concentrations of Pb, As, and Cd were found to be considerably higher than background levels across all industries, with a gradual decrease in PTE concentrations from 0 m to 500 m. The contamination factor indicated high to moderate contamination in agricultural soils by As, Cd, and Pb, and low contamination by Zn. pollution load index, modified contamination degree, and nemerow comprehensive index revealed varying pollution levels in the vicinity of the industries, with AA and AB showing higher pollution compared to AC. The individual risk factors demonstrated significant risks associated with Cd and As exposure, while Pb and Zn posed lower risks. The potential ecological risk index indicated considerable ecological risk for AA (risk index = 192.41), moderate risk for AB (risk index = 111.80), AC (risk index = 65.08), respectively. Correlation and principal component analysis revealed strong positive associations (p < 0.01) among the chemical parameters and potentially toxic elements in soils, and demonstrated the lead-acid battery industry as the primary contamination source in the studied areas. There were strong positive relationships (p < 0.01) existed between As, Cd, and Zn in soils and vegetables; while a strong negative association found between As in soils with As in Fruits. The cluster analysis showed EC, OC, OM, Pb, As and Zn into separate group, implied their same source of origin as anthropogenic source. The metal uptake was in the decreasing order of Cd > Zn > As > Pb and Cd > Zn > Pb > As in vegetable and fruit samples, respectively and transfer factor analysis highlighted Cd and Zn as metals with higher absorption rates in vegetables and fruits. Among the industries, AA and AB were significantly impacted on soil quality, and considerable metal accumulation found on vegetables. The human health risk assessment results indicate a potential noncarcinogenic health hazard for the populations surrounding the industries (AA, AB, and AC). This is evidenced by the calculation of the total target hazard quotient and the hazard index, both of which exceeded the acceptable level (>1). However, the carcinogenic health risks arising from the consumption of potentially toxic elements are within threshold values. This study provides crucial insights into the environmental as well as health impact of lead-acid battery industries, emphasizing the urgency of implementing effective environmental management practices to mitigate their consequences.

Phytoextraction potential of Canna indica (L.) for Cd removal from a hydroponic system

ABSTRACT The research explored Canna indica's ability to extract Cd in hydroponic conditions, determining its upper tolerance threshold and assessing Cd's impact on growth and biochemical properties. Plants were grown in 5L tanks containing nutrient solutions with varying Cd concentrations (0, 100, 200, 300, and 400 mg/L) for 18 days. Each treatment was performed in triplicate. Analysis of Cd content across roots, shoot, and leaves revealed high absorption rates of 89.5% to 96.8% efficiency for Cd treatments of 100–400 mg/L. Metrics like bioaccumulation coefficient (BAC), translocation factor (TF), and bio-concentration factor (BCF) were determined, indicating BAC > 1 across treatments, while TF was <1 for 100 mg/L and >1 for higher Cd treatments. Bio-concentration patterns varied with Cd concentration. Optimal Cd uptake occurred at 200–300 mg/L, declining notably at 400 mg/L. The study suggests C. indica's potential for phytoextraction up to 400 mg/L Cd contamination, but adverse effects emerged at ≥300 mg/L: reduced chlorophyll pigments, ascorbic acid, fresh/dry weights, and elevated leaf pH, indicating a Cd tolerance threshold of 300 mg/L for C. indica.

Dynamically tunable multifunctional terahertz absorber based on hybrid vanadium dioxide and graphene metamaterials.

In this work, in pursuit of a multifunctional device with a simple structure, high absorption rate, and excellent bandwidth, a tunable broadband terahertz (THz) absorber based on vanadium dioxide (V O 2) and graphene is proposed. Due to the phase transition of V O 2 and the electrically tunable properties of graphene, the structure realizes single broadband and dual-band absorption characteristics. When graphene is in the insulating state (E f=0e V) and V O 2 is in the metallic state, the developed system has more than 90% absorption and a wide absorption band from 1.36 to 5.48THz. By adjusting the V O 2 conductivity, the bandwidth absorption can be dynamically varied from 23% to more than 90%, which makes it a perfect broadband absorber. When graphene is in the metallic state (E f=1e V), V O 2 is in the insulating state, and the designed device behaves as a tunable and perfect dual-band absorber, where the absorptivity of the dual-band spectrum can be continuously adjusted by varying the Fermi energy level of graphene. In addition, both the broad absorption spectrum and the dual-band absorption spectrum maintain strong polarization-independent properties and operate well over a wide incidence angle, and the designed system may provide new avenues for the development of terahertz and other frequency-domain tunable devices.

Multiscale hybrid-structured femtosecond laser-induced graphene with outstanding photo-electro-thermal effects for all-day anti-icing/deicing

Multifunctional materials with photothermal and electrothermal effects have garnered considerable attention for solving the icing problem. Although great progress has been made in the field of anti-icing/deicing, the low electrothermal performance, complicated fabrication methods, and low durability restrict their widespread application. Here, we fabricate multiscale hybrid-structured femtosecond laser-induced graphene (FsLIG) on polyimide (PI) substrates using femtosecond laser direct writing technology in ambient air, and apply the FsLIG to all-day anti-icing/deicing. With the optimized laser scanning speed, the as-fabricated surface exhibits high light absorption rate (∼98.5%) in the range of 220–1400 nm and low sheet resistance (∼18.2 Ω sq−1), which bestows outstanding photo-electro-thermal effects on the FsLIG surface. Under 1.0 sun illumination or an applied voltage of 4 V, the average surface temperature can rise to ∼69.3 °C or ∼193.1 °C within 30 s. As a result, the FsLIG is successfully applied in anti-icing/deicing. The FsLIG surface realizes anti-icing and deicing when exposed to a sunlight intensity or an applied voltage of 1.0 sun or 2 V. The photo-electro-thermal material developed in this work, along with its simple preparation method, might have broad application prospects in the field of anti-icing/deicing.

Transient and steady models for blue laser directed energy deposition

Laser Directed Energy Deposition (DED) is an important process for additive manufacturing because of the advantage of high manufacturing speed. 450 nm blue laser has a higher absorption rate than traditional infrared laser for highly reflective materials such as Al and Cu. However, it is still unclear how the blue laser affects the particles and the molten pool flow in the DED process. In this work, we first designed two models to reveal the mechanism of the molten pool behaviors in the blue laser DED process: the transient model and the steady deposition model. The models are validated by in-situ and ex-situ experiments respectively. It is found that the three stages can be concluded for a particle impacting the molten pool: particle impacts, surface oscillates and the molten pool recovers. The particles whose diameter is less than 100 µm are necessary for steady deposition. The influence of process parameters on DED is investigated, and a suitable process parameters window is found. we also verified the superiority of the blue laser for DED of highly reflective materials through the simulation models. The current study provides new insights into the mechanism from the interaction in the molten pool scale to single-track forming in the blue laser DED, and can provide theoretical guidance on the application of blue laser DED of highly reflective materials.

Reduced Graphene Oxide/Cellulose Sodium Aerogel-Supported Eutectic Phase Change Material Gel Demonstrating Superior Energy Conversion and Storage Capacity toward High-Performance Personal Thermal Management.

By virtue of their capacity to absorb and release energy during the phase change process, phase change materials (PCMs) are ideal for personal thermal management (PTM). The combination of reduced graphene oxide/cellulose sodium aerogel (rGCA) and lauric acid/myristic acid binary eutectic phase change gel (LMG) creates a composite phase change material that possesses outstanding photothermal conversion capabilities, electro-thermal conversion capabilities, energy storage capabilities, and shape-stable performance. The results showed that rGCA had a maximum adsorption efficiency of 99.7% with a melting latent heat of 124.6 J g-1. The high absorption rate of rGCA to LMG is a result of the capillary force, pore characteristics, hydrogen bonding, and the π-π interaction. Notably, rGCA and LMG composite material (rGCG) exhibited an excellent photothermal conversion efficiency of 96.5% and electro-thermal conversion of 82.3%. Results indicate that binary eutectic phase change materials are more suitable for temperature regulation than single phase change materials, making them more suitable for PTM. It is anticipated that the innovative thermal comfort solution, which provides thermal shielding, thermal energy storage, self-supporting characteristics, and wearability, will offer new possibilities for the next generation of wearable PTMs.

Optimization of K2CO3 exposure conditions using response surface methodology for CO2 capture with 2-methylpiperazine and monoethanolamine as promoters

In this study, the optimization of potassium carbonate (K2CO3) exposure conditions for CO2 capture with the use of 2-methypiperazine (2MPz) and monoethanolamine (MEA) as promoters was investigated. The tested operating conditions for the CO2 capture process included the pH, temperature, K2CO3 dose, gas flow rate, and pressure, and their effect on the CO2 absorption/desorption rate and CO2 absorption efficiency was assessed. Response surface methodology (RSM) was also employed to determine the equations for the optimal long-term operating conditions. The results showed that the CO2 absorption rate and efficiency increased under K2CO3 exposure with an increase in the pressure and loading rate. Moreover, for the temperature the absorption efficiency first increase and then decreases with increase in temperature, however, the with increase in temperature the faster absorption were observed with lower absorption loading rate. Furthermore, pH had a more complex effect due to its variable effects on the speciation of bicarbonate ions (HCO3−) and carbonate ions (CO32−). Under higher pH conditions, there was an increase in the concentration of HCO3−, which has a higher CO2 loading capacity than CO32−. Contouring maps were also used to visualize the effect of different exposure conditions on the CO2 absorption rate and efficiency and the role of 2MPz and MEA as promoters in the K2CO3 solution for CO2 absorption. The results showed that the mean CO2 absorption rate was 6.76 × 10−4 M/L/s with an R2 of 0.9693 for the K2CO3 solution containing 2MPz. The highest absorption rate (6.56–7.20 × 10−4 M/L/s) was observed at a temperature of 298–313 K, a pressure of >2 bar, a pH of 8–9, and a loading rate of 80–120 L/h for a concentration of 1–3 M K2CO3 and 0.05–1.5 M 2MPz. The CO2 absorption efficiency exhibited a variation of 56–70% under the same conditions.

Inhibiting effect of 2-amino-2-methyl-1-propanol on gelatinous product formation in non-aqueous CO2 absorbents: Experimental study and molecular understanding

Diamines or polyamines with two or more amino groups are suitable for formulating non-aqueous absorbents (NAAs) with high CO2 loading capacity and low regeneration energy consumption. However, these two types of amines in NAAs are prone to produce insoluble gelatinous products after absorbing CO2, resulting in difficult operation of the CO2 capture system. In this study, by using 2-amino-2-methyl-1-propanol (AMP) as an inhibitor, the insoluble gelatinous products of the aminoethylethanolamine (AEEA)-N-methyl-2-pyrrolidone (NMP) (A-A-N) and 3-(methylamino)propylamine (MAPA)-NMP (M-A-N) NAAs were successfully eliminated. The experimental results showed that the AMP-regulated NAAs possessed a high absorption rate, high CO2 loading capacity, excellent desorption efficiency, and stable recyclability. The reaction mechanism of CO2 absorption and the inhibitory mechanism of AMP on the formation of gelatinous products were comprehensively elucidated. Taking the A-A-N system as a representative, AEEA reacted with CO2 to form zwitterionic protonated carbamate species (AEEACO2−(P)H+(S)), which tended to self-aggregate via hydrogen-bond interaction, resulting in the formation of insoluble gelatinous products. With the introduction of AMP, the AMP-derived products could combine easily with AEEACO2−(P)H+(S) via strong electrostatic attraction to form ion pairs, preventing the AEEACO2−(P)H+(S) molecules from self-aggregating to form insoluble gelatinous products. The regeneration heat duty of the A-A-N system was 1.89 GJ∙ton−1 CO2, which was 49.9 % lower than that of the benchmark 30 wt% MEA. Overall, introducing AMP as a gelatinous product inhibitor was beneficial for the development of NNAs with high CO2 absorption capacity and low-energy consumption.

Autologous fat grafting for cosmetic temporal augmentation: a systematic review.

Autologous fat grafting for temporal augmentation is increasingly popular in aesthetic surgery. However, its high absorption rate, unpredictable volume retention rate, and potential safety risks are significant drawbacks. Evaluation methods for the fat graft survival rate, especially volume retention in the temporal area, vary widely and tend to be more subjective than objective. Therefore, this systematic review aims to analyze the unpredictable volume retention rate, associated safety concerns, and the various assessment strategies following autologous fat grafting for cosmetic temporal augmentation. We conducted a systematic review of manuscripts listed in the MEDLINE/PubMed database on autologous fat grafting for cosmetic temporal augmentation. Articles had to be available in full text and written in English. Studies not presenting human data or not discussing cosmetic indications were excluded. We adhered to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. Eight articles were included. The average fat volume injected into each temporal region was 10.69 ml (range 6-17.5) on the right and 10.64 ml (range 5.9-17.4) on the left side. All included articles utilized photographic documentation before and after treatment, along with various questionnaires and scales (37.5% Likert Scale, 12.5% Hollowness Severity Rating Scale, 12.5% Visual Analogue Scale, 12.5% Allergan Temple Hollowing Scale). For objective assessment, one article (12.5%) used computed tomography, and another (12.5%) employed a three-dimensional scanning system to objectively evaluate fat graft survival. Autologous fat grafting effectively addresses temporal hollowness, with high patient satisfaction and a favorable safety profile. However, the variability in fat retention rates highlights the need for more controlled studies to establish reliable, validated methods for evaluating fat graft survival in the temporal area, and to further assess the safety of this procedure.

A review of the mechanical properties and durability of basalt fiber recycled concrete

Basalt fiber (BF) is an emerging environmentally-friendly fiber. Adding basalt fiber can improve the deficient recycled concrete's poor mechanical properties and durability. By reviewing nearly 120 related papers, the effects of variables such as BF content and length (0–1.5%, 9–18 mm), recycled aggregate substitution rate (0–100%), and cement mix ratio (w/b, 0.25–0.45) on the mechanical and durability properties of basalt fiber-reinforced recycled concrete (BFRAC) were discussed. Due to the presence of vulnerable interfacial transition zones, the mechanical properties of recycled concrete (RAC) continuously deteriorate over time. However, by adding an appropriate amount of basalt fiber, it is possible to improve these structural defects by forming a network structure that enhances cracking resistance within the matrix and improves interface bonding strength among other benefits. Consequently, this significantly improves the overall mechanical properties of RAC. Additionally, while incorporating recycled aggregate (RA) may reduce compressive strength initially, this deficiency can be mitigated through the proper inclusion of fibers in RAC mixtures. Optimal compressive strength for RAC is achieved with a replacement ratio between 25–50% and a fiber content ranging from 0.2–0.3%. Furthermore, properly incorporating fibers into RAC greatly enhances splitting tensile strength and flexural strength as well; specifically achieving optimal splitting tensile strength with a replacement ratio between 40%− 50%, a fiber content at 0.3%, and utilizing fibers with lengths measuring approximately 12 mm long. The primary cause for poor frost resistance in RAC lies within numerous micro-cracks and pores present in RA aggregates which lead to high water absorption rates ultimately reaching critical water saturation points resulting in freeze-thaw damage occurrences during exposure to freezing conditions. When exposed to sulfate attack, RAC undergoes a chemical reaction with sulfate ions present in the concrete, leading to the formation of numerous expansion products that negatively impact concrete performance. Progressive dehydration of hydration products under high-temperature conditions leads to a porous structure within the concrete matrix. Incorporating fibers can impede microcrack expansion during freeze-thaw, sulfate attack, and high-temperature environments, thus enhancing the erosion resistance of RAC. Compared to conventional concrete, interfacial bonding in RAC is less tight and more vulnerable to damage in complex environments. Current research on RAC suggests that the mechanism behind its damage under complex freeze-thaw load coupling environments remains unclear. It is recommended that future studies combine large-scale component tests with computational simulations to address this issue.

Phosphate-rich cellulose beads for efficient cesium extraction from aqueous solutions: a novel approach for cellulose utilization.

In this work, phosphate-rich cellulose beads (CBPs) were first used for cesium extraction from aqueous solutions. These green, abundant, cheap, and renewable CBPs demonstrated a high adsorption capacity and fast absorption rate. Besides, the CBPs also exhibited excellent stability and recycling performance, as well as good selectivity. This study presents the promising application potential of cellulose for efficient cesium extraction from aqueous media.

Dual Functional Magnetic Nanoparticles Conjugated with Carbon Quantum Dots for Hyperthermia and Photodynamic Therapy for Cancer.

The global incidence of cancer continues to rise, posing a significant public health concern. Although numerous cancer therapies exist, each has limitations and complications. The present study explores alternative cancer treatment approaches, combining hyperthermia and photodynamic therapy (PDT). Magnetic nanoparticles (MNPs) and amine-functionalized carbon quantum dots (A-CQDs) were synthesized separately and then covalently conjugated to form a single nanosystem for combinational therapy (M-CQDs). The successful conjugation was confirmed using zeta potential, Fourier transform infrared spectroscopy (FT-IR), and UV-visible spectroscopy. Morphological examination in transmission electron microscopy (TEM) further verified the conjugation of CQDs with MNPs. Energy dispersive X-ray spectroscopy (EDX) revealed that M-CQDs contain approximately 12 weight percentages of carbon. Hyperthermia studies showed that both MNP and M-CQDs maintain a constant therapeutic temperature at lower frequencies (260.84 kHz) with high specific absorption rates (SAR) of 118.11 and 95.04 W/g, respectively. In vitro studies demonstrated that MNPs, A-CQDs, and M-CQDs are non-toxic, and combinational therapy (PDT + hyperthermia) resulted in significantly lower cell viability (~4%) compared to individual therapies. Similar results were obtained with Hoechst and propidium iodide (PI) staining assays. Hence, the combination therapy of PDT and hyperthermia shows promise as a potential alternative to conventional therapies, and it could be further explored in combination with existing conventional treatments.