High-power Laser Pulses Research Articles

Versatile design for temporal shape control of high-power nanosecond pulsed fiber laser amplifier.

This research proposed a novel pulse-shaping design for directly shaping distorted pulses after the amplification. Based on the principle of the design we made a pulse shaper. With this pulse shaper, we successfully manipulate the pulse's leading edge and width to achieve an 'M'-shaped waveform in an amplification system. Comparative experiments were conducted within this system to compare the output with and without the integration of the pulse shaper. The results show a significant suppression of the nonlinear effect upon adding the pulse shaper. This flexible and effective pulse shaper can be easily integrated into a high-power all-fiber system, supplying the capability to realize the desired output waveform and enhance the spectral quality.

Experimental study of injection seeded single-longitudinal-mode Q-switched fiber laser

--The role of injection seeding power on the operation and output characteristics of a single-longitudinal-mode (SLM) injection seeded Q-switched fiber laser is investigated. The mode coupling between seeding laser and the potential longitudinal-modes of the oscillator changes as the injection seeding power increase. So the Q-switched laser may operate at different regimes which can be distinguished by the pulse features. Only with a proper range of injection seeding power that is not too larger or too small, the operation of injection seeded Q-switched fiber laser with narrow-linewidth, high peak power and narrow pulsewidth laser pulses is possible. The Q-switched fiber laser linewidth is narrowed through inserting a dual-OCs oscillator into the laser cavity. 200-ns, 1-W peak power SLM Q-switched laser pulse with nearly transform-limited linewidth is obtained when the pump power is 300 mW.

Optical and thermal simulation design of tapered waveguide for high-power pulsed quantum cascade laser

Optical and thermal simulation design of tapered waveguide for high-power pulsed quantum cascade laser

A design of debris mitigation system for high-repetition-rate petawatt laser experiments

The shooting of high-power laser pulses on solid targets will generate a large amount of debris which can damage the expensive optical elements and impair the laser focusing quality. The existing and upcoming high-repetition-rate petawatt lasers which are able to deliver hundreds of shots in minutes would face more serious debris problems. In this work, we propose a high-speed-spinning multi-disc debris mitigation system. An optimization method based on Bayesian Optimization is developed to acquire the optimal parameters of the system.

Dense plasma diagnostics with a Nomarski interferometer using a frequency-tripled Ti:sapphire laser

An overdense plasma is considered as a new tool for high-power laser pulse compression. For this purpose, a high density plasma was generated by illuminating an intense fs Ti:sapphire laser pulse onto a surface of an aluminum disk and its spatio-time-resolved dynamics was investigated by a Nomarski interferometer. To probe the laser-produced high density plasma, the original Ti:sapphire laser pulse with a wavelength of 800 nm was frequency-tripled and the UV laser pulse of 266 nm in wavelength was used in the interferometer. It turned out that the fs UV laser interferometer can provide a fairly high density information up to 8.5 × 1020 cm-3. Our experimental result shows that the initial high density plasma near the solid target surface expands rapidly and its density profile in space is gradually reduced to exponential in the ns time scale. This result will provide an important information towards the next step for experimental demonstration of the laser pulse compression using a plasma.

Study the effect of the different doses from the laser on Staphylococcus aureus Bacteria growth in vitro

Background: Laser is a novel physical therapy technique used to treat various conditions, including wound healing, inhibition of bacterial growth, and postoperative wounds. High-power pulsed alexandrite laser therapy is one of the most prevalent forms of laser therapy, which is a noninvasive method for treating various pathological conditions, thereby enhancing functional capacities and quality of life. It is a modern medical and physiotherapeutic technology. Generally, the Alexandrite laser emits infrared light with a wavelength of 755 nm, allowing it to propagate and penetrate tissues. Objective: This study focused on the application of a high-power pulsed alexandrite laser in vitro to evaluate the effect of a pulsed alexandrite laser on antibiotic-resistant bacteria utilizing varying exposure times, pulse durations, and laser fluencies to determine which dose is more effective on S. aureus bacteria. Method: The laser used in this study was the alexandrite laser which was considered a pulsed laser and had the following parameters: The wavelength was 755 nm, the beam diameter was (14 mm), the exposure times varied (30, 60, 90) seconds, the laser fluency (5, 10, 15 and 20 J.Cm-2). The study was carried out after the bacteria were diagnosed as being antibioticresistant. They were exposed to different doses of Alexandrite laser. Three samples of bacteria were exposed to laser beams for 30 seconds with a 5ms pulse duration and with a laser fluency of 5J/cm2, and this process was repeated with laser fluencies of 10, 15, and 20. This procedure was repeated using exposure times of 60sec and 90sec. As well as, this process was repeated by exposure with 30 sec, 60 sec and 90 sec exposure times, 10ms and 20ms pulse durations and with different laser fluencies 5, 10, 15 and 20J/cm2, separately. Results: A significant reduction (p = <0.0001) in the mean values of the colony was observed with the increase of laser fluency doses compared with control at the same pulse duration. A significant reduction (p = <0.0001) in the mean count of the colonies was observed in the comparison between two laser fluences at the same pulse duration. In conclusion, the exposure times, pulse durations and laser fluencies of pulsed alexandrite laser showed an effect on the mean count of the colonies of S aureus bacteria and determined the effective dose. Keywords: laser, Staphylococcus aureus, Bacteria growth

Relativistic Magnetic Reconnection in Colliding Plasma Clouds Generated by Multiple High Power Laser Pulses

Relativistic Magnetic Reconnection in Colliding Plasma Clouds Generated by Multiple High Power Laser Pulses

Dual-Pulsed Laser Ablation of Oyster Shell Producing Novel Thin Layers Deposed to Saccharomyces cerevisiae.

Dual-pulsed (DPL) laser deposition using oyster shells as targets was studied in order to find out if this method can replace the use of high-power pulsed lasers. Aspects related to changes in the morphological structure of the thin layer but also to the chemical composition of the obtained thin layer were analyzed and compared with the target as well as with the thin layers obtained with a higher power pulsed laser in a single-pulsed (SPL) regime. Orthorhombic structures were noticed with Scanning Electron Microscopy for the thin film obtained in DPL mode compared to the irregular particles obtained in SPL mode. The deacetylation process during ablation was evidenced by Fourier Transform Infrared spectroscopy, resulting in chitosan-based thin films. The effect of the obtained thin films of chitosan on the cells of baker's yeast (Saccharomyces cerevisiae) was studied. Restoration of the yeast paste into initial yeast was noticed mainly when the hemp fabric was used as support for the coating with yeas which was after that coated with chitosan thin film produced by DPL method.

Actively Q-switched self-frequency-doubled Yb:YCOB green laser with output power of a dozen watts.

A diode laser (LD) end-pumped acousto-optic Q-switched self-frequency-doubled (SFD) Yb:YCa4O(BO3)3 (Yb:YCOB) pulsed green laser was realized for the first time (to our knowledge), with a maximum average output power of 11.6 W and an optical conversion efficiency of 30.0% from the LD to SFD lasers. The wavelength of the SFD lasers was controlled to be 507 nm for improving quantum efficiency up to 96% and reducing thermal effects. The repetition rates ranged from 20 to 500 kHz, and the maximum pulse energy was 312.0 µJ with a peak power of 4.78 kW at a repetition rate of 20 kHz. This work represents the highest output power in the SFD pulsed lasers and provides an efficient and compact way to generate high-power pulsed green lasers that should have important applications in many aspects, such as ultraviolet (UV) laser generation, laser display, and medical, military, and scientific research.

Design of a large-mode-area tapered fiber amplifier for amplification of ultrashort laser pulses at 1535 nm wavelength

We design a W-type large-mode-area erbium doped tapered fiber with effective mode area varying from 1770 µm2 to 840 µm2with tolerance ± 0.0005 in refractive indices of different layers of fiber. The beam quality of the pulses is ensured by effective single-mode operation. We investigate the amplification of high power femtosecond pulses in this fiber by using nonlinear Schrodinger equation including gain term. It is solved using split-step Fourier method for both up-tapered (effective mode area increasing along the length) and down tapered (effective mode area decreasing along the length) fiber configurations at centered around 1535 nm wavelength. In both configurations of fiber, input pulse parameters like peak power, pulse width, and fiber length are calculated for maximum amplification with the least amount of pulse shape distortion. In down-tapered configuration, we numerically demonstrate the amplification of 1 kW peak power, 560 fs duration pulse to 3.6 MW peak power, 12 fs amplified pulse. In up-tapered configuration, we obtain the amplification of 2 kW, 565 fs input pulse to ∼7.9 MW peak power, ∼11 fs pulse. The fiber is useful for amplifying high-power laser pulses, and the resulting pulses can be used for laser processing, spectroscopy, and remote sensing.

In Vitro Assessment of the Effects of Varying Dosages of Alexandrite Laser on the Development of Staphylococcus Aureus

Background: This study aimed to apply a high-power pulsed alexandrite laser in vitro, the researchers tested different exposure periods, pulse lengths, and laser fluencies to see which dosage was most successful against S. aureus bacteria, which had developed resistance to many antibiotics. Method: Three bacteria samples were exposed to laser beams for 30 seconds with a 5ms pulse duration and a laser fluency of 5J/cm2. The process was repeated with laser fluencies of 10, 15, and 20. Results: The study was carried out by using different doses of Alexandrite laser. Results: There are significant differences (p = 0.05) in the mean number of bacteria colonies exposed for 30 and 60 seconds at any laser fluencies utilized in the present investigation. Except for the 15 J.cm-2 laser fluency; there was a statistically significant difference (p < 0.001) between 60 sec and 90-sec exposure durations. Conclusion: In conclusion, the exposure periods, pulse durations, and laser fluencies of pulsed alexandrite laser were found to have an influence on the mean colony count of S aureus bacteria and to establish the effective dose.

Study on transient photocurrent induced by energy level defect of schottky diode irradiated by high power pulsed laser

The transient photocurrent is one of the key parameters of the spatial radiation effect of photoelectric devices, and the energy level defect affects the transient photocurrent. In this paper, by studying the deep level transient spectrum of a self-designed Schottky diode, the defect properties of the interface region of the anode metal AlCu and Si caused by high-temperature annealing at 150 ℃, 200 ℃ and 300 ℃ for 1200 h have been quantitatively analyzed. The study shows that the defect is located at the position of + 0.41 eV on the valence band, the concentration is 2.8 times 1013/cm2, and the capture cross section is sigma = 8.5 times 1017. The impurity energy level mainly comes from the diffusion of Al atom in anode metal. We found that the defect did not cause the electrical performance degradation and obvious morphology change of the device, but the transient photocurrent increased significantly. The reason is that the high temperature treatment results in a growth in the density of states at the interface between AlCu–Si. The more mismatched dislocations and recombination center increased the reverse current of the heterojunction. The above view is proved by the TCAD simulation test.

Condition for Stopping the Collapse of High-Power Femtosecond Laser Pulses during Propagation through an Optical Medium

Condition for Stopping the Collapse of High-Power Femtosecond Laser Pulses during Propagation through an Optical Medium

High-power xenon lamp-pumped Er:YAP pulse laser operated in free-running and acousto-optical Q-switching modes

We demonstrate a high-energy and high-power pulse laser on a xenon lamp-pumped Er:YAP crystal. The laser performance and thermal focal lengths under different working frequencies are discussed. The results show that the thermal lens effect is gradually aggravated with the increase of working frequencies, and even working at 100 Hz, a single pulse energy of 234 mJ can be achieved. A maximum average power of 41.5 W is achieved with a working frequency of 20 Hz and slope efficiency of 2.82%. This output power is much higher than other xenon lamp-pumped erbium laser devices. A Q-switched laser is demonstrated by using the TeO2 crystal, the maximum output energies of 11.5 mJ and 3.5 mJ are obtained at 50 and 100 Hz, the corresponding peak powers are 93.4 kW and 17.2 kW, respectively. The laser wavelengths and beam quality factors are also characterized in the free-running and Q-switched modes. A higher pulse energy and peak power laser could be achieved further by improving the damage threshold of TeO2 acousto-optical Q-switching. All the experimental results illustrate that the xenon lamp-pumped Er:YAP laser is a promising candidate for high-power and high-frequency mid-infrared laser devices.

A spall and diffraction study of nanosecond pressure release across the iron ε-α phase boundary

The extreme response of polycrystalline iron at high pressures and high strain rates is revealed by means of high-power laser pulses. The compression portion of the pulse coupled with x-ray diffraction identifies the expected body-centered cubic (α) to hexagonal close packed (ε) displacive transformation. Upon release, observation shows that the complete reverse transformation takes approximately 8 ns and that the structure returns to its initial microstructural configuration, in a reversible transformation path. This is in good agreement with molecular dynamics (MD) simulations which predict an inverse dependence between transformation time and strain rate. The grain size is reduced from μm to nm range during compression and begins increasing back to the original grain size on decompression. The kinetics of the transition is dictated by heterogenous nucleation as it follows the Johnson-Mehl-Avrami-Kolmogorov equation with the appropriate time exponent of ∼1. This is confirmed by MD simulations which also identify profuse twinning and dislocation generation. The tensile pulse generated upon reflection at the free surface is captured by time-resolved free surface velocity measurements from which a peak tensile stress of 7 GPa is obtained, in stark contrast with its quasi-static value of ∼200 MPa. At these strain rates, the strength of grain interiors, which is determined by twinning and slip exceeds the strength of the boundaries, and failure initiates preferentially in the latter.

Targeting new ways for large-scale, high-speed surface functionalization using direct laser interference patterning in a roll-to-roll process

Direct Laser Interference Patterning (DLIP) is used to texture current collector foils in a roll-to-roll process using a high-power picosecond pulsed laser system operating at either fundamental wavelength of 1064 nm or 2nd harmonic of 532 nm. The raw beam having a diameter of 3 mm @ 1/e 2 is shaped into an elongated top-hat intensity profile using a diffractive so-called FBS®-L element and cylindrical telescopes. The shaped beam is split into its diffraction orders, where the two first orders are parallelized and guided into a galvanometer scanner. The deflected beams inside the scan head are recombined with an F-theta objective on the working position generating the interference pattern. The DLIP spot has a line-like interference pattern with about 15 μm spatial period. Laser fluences of up to 8 J cm−2 were achieved using a maximum pulse energy of 0.6 mJ. Furthermore, an in-house built roll-to-roll machine was developed. Using this setup, aluminum and copper foil of 20 μm and 9 μm thickness, respectively, could be processed. Subsequently to current collector structuring coating of composite electrode material took place. In case of lithium nickel manganese cobalt oxide (NMC 622) cathode deposited onto textured aluminum current collector, an increased specific discharge capacity could be achieved at a C-rate of 1 °C. For the silicon/graphite anode material deposited onto textured copper current collector, an improved rate capability at all C-rates between C/10 and 5 °C was achieved. The rate capability was increased up to 100% compared to reference material. At C-rates between C/2 and 2 °C, the specific discharge capacity was increased to 200 mAh g−1, while the reference electrodes with untextured current collector foils provided a specific discharge capacity of 100 mAh g−1, showing the potential of the DLIP technology for cost-effective production of battery cells with increased cycle lifetime.

Mathematical modeling of experiments on the interaction of a high-power ultraviolet laser pulse with condensed targets

Objectives. The paper aimed to review and analyze the results of works devoted to numerical modeling of experiments on the interaction of high-power ultraviolet (UV) laser pulses with condensed targets. The experiments were carried out at GARPUN, the powerful KrF-laser facility at the P.N. Lebedev Physical Institute of the Russian Academy of Sciences (Moscow). The relevance of the research is related to the use of excimer UV lasers as a driver for a thermonuclear reactor. Physical aspects of laser-plasma interaction, including those related to the possibility of using two-sided cone target in a fission-fusion reactor, are discussed.Methods. The research is based on physico-mathematical models, including Euler and Lagrange.Results. The mathematical modeling of three types of natural experiments is presented: (1) burning through different thicknesses of Al foils by high-power UV laser; (2) studying hydrodynamic instability development at the UV laser acceleration of thin polymer films and features of turbulent zone formation; (3) interaction of high-power UV laser pulses with two-layer targets (Al + Plexiglas) and study of fine structures. Numerical modeling showed that a hybrid reactor with UV laser driver can use targets in the form of two-sided counter cones.Conclusions. Physico-mathematical models are developed along with 2D codes in Lagrangian and Eulerian coordinates as confirmed in the results of natural experiments. The models can be used to describe the physics of high-power UV laser pulses interacting with various targets and forecast the results of reactor-scale experiments.

Manipulation of femtosecond laser filamentation by wire mesh amplitude mask

The results of numerical simulation on the propagation of high-power femtosecond laser pulses in air under conditions of the amplitude modulation are presented. Laser pulse amplitude modulation is realized by using the metal mesh-masks, which divide the initial laser beam into lower-energy parts (subbeams). We show that, in general, the beam energy partitioning by metal meshes reduces the total length of beam filamentation region in air, whereas the longitudinal continuity of the laser plasma distribution in the filaments is considerably improved. A strong dependence of the filamentation region parameters (starting coordinate, length, longitudinal continuity) on the position of the mesh-mask relative to the laser beam axis is also revealed. It turns out that under certain conditions, when the beam axis points to the mesh crossing, the spatial position of the filaments can be shifted further along the propagation path by increasing the size of the mesh cells. Alternatively, if the beam center exposes the mesh cell opening, the filamentation start coordinate decreases monotonically when the mesh becomes sparser. Additionally, the parameters of the filamentation region exhibit high sensitivity to the mesh wire thickness that can dominate the influence of mesh position and cell size.

Theoretical Analysis of Thermal Distribution and Waveform Evolution in Pulsed Ytterbium-Doped Fiber Amplifier with Extra Feedback

Pulsed ytterbium-doped fiber amplifiers (YDFA) with ns-level signal width are important devices for obtaining high-power pulsed lasers. When some components in the amplifier are ineffective, e.g., the isolator or fiber is damaged, extra feedback light is generated and coupled into the gain fiber. The dynamic thermal distribution and waveform evolution of amplifiers with extra continuous-wave (CW) or pulse-wave (PW) feedback are theoretically analyzed in this work. The CW feedback can not only reduce the gain of the amplifier but can also change the thermal distribution of the gain fiber, while the PW feedback can reduce the leading or trailing edge of the output pulse by 3–4 ns, depending on the direction of the feedback light transmission. The theoretical analysis provides a reference for optimizing the thermal management and the fault diagnosis of a typical fiber amplifier with an output of several tens of watts.

Highly efficient harmonic vortex generation from a laser irradiated hollow-cone target.

It has been recently reported that ultraviolet harmonic vortices can be produced when a high-power circular-polarized laser pulse travels through a micro-scale waveguide. However, the harmonic generation quenches typically after a few tens of microns of propagation, due to the buildup of electrostatic potential that suppresses the amplitude of the surface wave. Here we propose to use a hollow-cone channel to overcome this obstacle. When traveling in a cone target, the laser intensity at the entrance is relatively low to avoid extracting too many electrons, while the slow focusing by the cone channel subsequently counters the established electrostatic potential, allowing the surface wave to maintain a high amplitude for a much longer distance. According to three-dimensional particle-in-cell simulations, the harmonic vortices can be produced with very high efficiency >20%. The proposed scheme paves the way for the development of powerful optical vortices sources in the extreme ultraviolet regime-an area of significant fundamental and applied physics potential.