High Power Conversion Research Articles

Transferable Percolated Particle Monolayers Derived from Marangoni Flows for Thermally Conductive Dielectric Coatings.

Thermal management is becoming one of the most significant design and size limitations for high power density electronics, including motherboards, power converters, and phased array antennas for 5G communications. There are few options for conducting heat away with dielectric materials that avoid shortening or distorting the performance of these electronics. Certain highly thermally conductive 2D and 3D materials, including hexagonal boron nitride and diamond, offer ideal material properties to address these issues but are extremely challenging to process. This work studies highly oriented single-particle thick films of hexagonal boron nitride, manufactured through a modified Langmuir-Blodgett process and densified further using the Marangoni effect to attain remarkable thermal conductivity enhancement with minimal coating thickness. High loadings of hexagonal boron nitride (∼60 vol %) in dense, castable films are also produced to compare thermal spreading ability in a comparatively simpler but less-coordinated percolated system to the highly percolated particle monolayers. These procedures were applied to glass fiber reinforced polymers used in aerospace and radome applications as well as to a single-board computer to demonstrate enhanced thermal management.

2D g-C3N5 p-Doping of Donor Material for High-Efficiency Organic Solar Cells.

Molecular doping of organic semiconductor is a great strategy for significantly regulating the electronic band structure of organic semiconductor while increasing charge mobility and carrier concentration. Here, a facile strategy is presented by introducing 2D g-C3N5 as a p-dopant into PM6, improving the charge mobility and hole carrier concentration of PM6. Moreover, the electron transfer between PM6 and g-C3N5 can effectively downshift the Fermi energy level and highest occupied molecular orbital (HOMO) energy level of PM6, which leads to the increase the built-in electric field of organic solar cells (OSCs). The addition of g-C3N5 also effectively enhances the crystallization of active layer, thereby improving the stability of OSCs. As a result, a champion bulk-heterojunction (BHJ) and layer-by-layer (LbL) structure OSCs are successfully achieved featuring a high-power conversion efficiency of 18.10%/18.25%, simultaneously having excellent device stability. This work shows that introducing a low concentration dopant into organic donor is an effective method for improving the electrical performance of organic donor and the efficiency of OSCs.

Multifunctional Reconfigurable Operations in an Ultra-Scaled Ferroelectric Negative Transconductance Transistor.

The integration of functional materials into electronic devices has become a key approach to extending Moore's law by increasing the functional density of electronic circuits. Here, we present a device technology based on ultrascaled ferroelectric, antiambipolar transistors (ferro-AAT) with robust negative transconductance, enabling a wide range of reconfigurable functionalities with applications in both the digital and analog domains. The device relies on the integration of a hafnia-based ferroelectric gate stack on a vertical nanowire tunnel field-effect transistor. Through intentional gate/source overlap and tunnel-junction engineering, we demonstrate enhanced antiambipolarity with a high negative transconductance that is reconfigurable using the nonvolatile remanent polarization of the ferroelectric. Experimental validation highlights the versatility of this ferro-AAT in two implementation scenarios: content addressable memory (CAM) for high-density data search and reconfigurable signal processing in analog circuits. As a single-transistor cell for CAMs, the ferro-AAT shows subpicojoule operation for one search with a compact footprint of ∼0.01 μm2. For single-transistor-based signal modulation, multistate reconfigurations and high power conversion (>95%) are achieved in the ferro-AAT, resulting in a significant reduction in the complexity of analog circuit design. Our results reveal that the distinctive device properties allow ferro-AATs to operate beyond conventional transistors with multiple reconfigurable functionalities, ultrascaled footprint, and low power consumption.

Design and analysis of a high-efficiency bi-directional DAB converter for EV charging

The escalating demand for electric vehicles (EVs) arises from apprehensions regarding fossil fuel depletion and the ecological repercussions of conventional combustion engines, propelling the transition towards environmentally sustainable alternatives. EVs are conventionally comprised of a powertrain, battery management system, and communication infrastructure, with the battery playing a pivotal role. Achieving an efficient EV battery charger necessitates the implementation of a proficient charging algorithm and a high-power converter capable of adeptly regulating battery parameters. Among the array of available options, a bi-directional DC/DC converter is often employed for this purpose. This study predominantly focuses on the Bi-Directional Dual Active Bridge Converter with Single-Phase Shift Control. It is renowned for attaining a broad voltage range through transformer turn ratio adjustments. Its controllable parameters, such as phase shift ratio and duty cycle, bolster its versatility. Moreover, due to its input–output isolation and minimal passive elements, this converter exhibits superior efficiency due to its soft-switching capabilities. The analytical framework encompasses steady-state and dynamic assessments, small-signal modeling, and system transfer function analysis, all of which contribute to formulating an optimized controller design. Additionally, the study conducts simulations of various battery charging techniques, including constant current (CC), constant voltage (CV), and CCCV mode, employing a 1.5 kW Dual Active Bridge DAB-based charger through MATLAB/SIMULINK. Furthermore, voltage mode control simulations for a 5 kW DAB converter augment the study's insights into effective EV charging strategies.

The influence of precursor solutions containing an amount of silver bismuth sulfide nanoparticles (AgBiS2 NPs) on the characteristics of CH3NH3PbI3 perovskites solar cells

The utilization of organo-metal halide perovskites as absorbers in thin-film solar cells has garnered considerable interest from the scientific community in recent times. In this study, we present the introduction of silver bismuth sulfide nanoparticles (AgBiS2 NPs) doped into perovskite thin films composed of CH3NH3PbI3 thin film. Our results demonstrate that the perovskites' morphology and structure were significantly improved. The effects of AgBiS2 NPs concentration on the optical, mechanical, and crystallographic properties of CH3NH3PbI3 perovskite thin films were investigated. The findings from the structure investigations revealed that an increase in the concentration of AgBiS2 NPs resulted in a transition from a low-crystalline to a polycrystalline structure of the perovskite thin films. An elevation in the concentration of AgBiS2 NPs from 2 to 8 mg/mL led to the development of perovskite films of superior quality, consisting entirely of PbI3 and CH3NH3. These films exhibited almost impeccable deposition, compactness, and uniformity, and their particle size reached an approximate value of 1.3 μm. Furthermore, an increase in the optical absorption coefficient (∼105 cm−1) in the visible spectrum and subsequent enhancements in photoluminescence (PL) and ultraviolet–visible (UV–Vis) absorption spectroscopy serve as further evidence of the film's enhanced quality. When AgBiS2 NPs are doped into perovskites, the films' quality is significantly improved; they acquire a uniform surface morphology, an exceptional crystal structure, and enhanced light absorption, all of which contribute to accelerated PL quenching and charge transfer. Power conversion efficiency (PCE) was enhanced across all photovoltaic parameters through the use of larger granules in bulk-heterojunction solar cells, as opposed to undoped heterojunction solar cells. The PCE of the perovskite device with CH3NH3PbI3 base is 17.04 % at the optimal concentration of 6 mg/mL AgBiS2 NPs. These findings indicate that the doping of CH3NH3PbI3 perovskite thin films with AgBiS2 NPs is essential for the achievement of high crystallinity, a large particle size, and a high absorption coefficient. These properties are advantageous for the high-power conversion efficiency of solar cell applications.

Cross-Linking-Integrated Sequential Deposition: A Method for Efficient and Reproducible Bulk Heterojunctions in Organic Solar Cells.

The formation of bulk heterojunctions (BHJs) through sequential deposition (SqD) of polymer donor and nonfullerene acceptor (NFA) solutions offers advantages over the widely used single-step deposition of polymer:NFA blend solutions (BSD). To enhance the application of SqD in organic solar cell production, it is crucial to improve reproducibility and stability while maintaining a high efficiency. This study introduces a novel method termed cross-linking-integrated sequential deposition (XSqD) for fabricating efficient and reproducible BHJs. In this method, polymers are cross-linked using efficient 2Bx-4EO or 2Bx-8EO cross-linkers, which enhance the solvent resistance of the polymer donor layer against the solvents used for NFAs. This approach addresses the challenge of selecting a suitable solvent for NFAs, a major obstacle in SqD-processed OSCs. The utilization of 2Bx-4EO in XSqD leads to a significant increase in reproducibility compared to that of conventional SqD, coupled with a high-power conversion efficiency (PCE) of 14.1%. Furthermore, XSqD devices exhibit superior stability, showing only 1% and 6% reductions in their initial PCE after thermal stress at 80 and 120 °C for 50 h, respectively.

Hardware Testing Methodologies for Wide Bandgap High-Power Converters

Wide bandgap (WBG) power semiconductor devices are increasingly replacing silicon IGBTs in high-power and high-voltage power electronics applications. However, there is a significant gap in the literature regarding efficient testing methodologies for high-power and high-voltage converters under constrained laboratory resources. This paper addresses this gap by presenting comprehensive, hardware-focused testing methodologies for high-power and high-voltage WBG power semiconductor-based converter bring-up before the control validation phase steps in. The proposed methods enable thorough evaluation and validation of converter hardware, including device switching characteristics, driving circuit functionality, thermal management performance, insulation integrity, and sustained operation at full power. We utilized the double pulse test (DPT) to characterize switching performance in a two-level phase leg configuration, extract circuit parasitics, and validate magnetic components. The DPT was further applied to optimize gate driving circuits, validate overcurrent protection mechanisms, and measure device on-resistance. Additionally, a multicycle test was introduced to rapidly assess steady-state converter performance and estimate efficiency. Recognizing the critical role of thermal management in high-power converters, our methodologies extend to the experimental extraction of key thermal parameters—such as junction-to-ambient thermal resistance and thermal capacitance—via a heat loss injection method. A correlation method between temperature sensor measurements and junction temperature is presented to enhance the accuracy of device temperature monitoring during tests. To ensure reliability and safety, dielectric withstand tests and partial discharge measurements were conducted at both component and converter levels under conventional 60 Hz sinusoidal and high-frequency PWM waveforms. Finally, we highlight the importance of testing converters under full voltage, current, and thermal conditions through power circulating tests with minimal power consumption, applicable to both non-isolated and isolated high-power converters. Practical examples are provided to demonstrate the effectiveness and applicability of these hardware testing methodologies.

Optimizing electron transport layers for high-efficiency perovskite solar cells using impedance spectroscopy

The best interface for a perovskite solar cell is designed to facilitate effective charge transport to achieve a high-power conversion efficiency. Tin dioxide (SnO2) is widely recognized as an electron transport material for perovskite solar cells, offering advantages such as low hysteresis, low defect concentration, and low fabrication temperature. However, the low conduction band edge of SnO2 restricts the built-in potential of the solar cell device. In this study, we designed a double layer of electron transport by applying zinc oxide (ZnO) on SnO2 to improve the electron transport properties in perovskite solar cells. The bilayer of electron transport enhances the interfaces between the perovskite and the electron transport layer, leading to an improvement in the efficiency and stability of solar cell devices up to 11.71 % compared to a single SnO2 layer device with a PCE of 9.06 %. The introduction of ZnO reduces charge recombination, resulting in a lower recombination resistance (Rrec). Also, charge transfer resistance (Rct) of ZnO/SnO2 increased to 16.6KΩ compared to a single SnO2 layer device with a Rct of 5.29KΩ. Our findings provide valuable insights into the design of electron transport layers for perovskite solar cells and highlight the importance of electrochemical impedance spectroscopy in understanding the dynamic processes that govern their performance.

Design and optimization study of all inorganic based double-absorption- layer CsPbI3/MoS2 heterojunction perovskite solar cells by SCAPS-1D

In recent years, perovskite solar cells (PSCs) continue to be a popular issue due to their high-power conversion efficiency (PCE%) and cost-effective production process. The CsPbI3 absorber layer used to produce PSCs limits the efficiency of the structure because it can absorb low-energy photons. Therefore, in this study, for the first time, CsPbI3 and CsPbI3/MoS2 single and double absorber based inorganic heterojunction PSCs were studied in detail, compared and optimized by using Solar Cell Capacitance Simulator (SCAPS-1D) software package. We discussed how the photovoltaic efficiency changed based on the open-circuit voltage (Voc), circuit current density (Jsc), quantum efficiency (QE), PCE% and fill factor (FF) relies on layer thickness, operating temperature, defect density (Nt), acceptor (NA) and donor density (ND), and heterojunction design. CuSbS2 and PCBM were chosen as the HTL and ETL layers, respectively. Depending on the results obtained from the SCAPS-1D, the optimum parameters for the Au/HTL/CsPbI3/ETL/FTO single layer device were determined as Thickness = 300 nm, Nt = 1011 cm-3, NA = 1013 cm-3, and T = 310 K. Then, the optimum parameters of MoS2 for the Au/HTL/CsPbI3/MoS2/ETL/FTO double layer-based device were determined as Thickness = 600 nm, Nt = 1010 cm-3 and ND = 1018 cm-3. It has been observed that MoS2 increases the light absorption capacity of the PSC device. As a result, the solar cell efficiency of the device with MoS2 has improved from 20.44 % to 40.66 % compared to the single-layer device. Additionally, in this study, presented a new approach for the future development at highly efficient, stable and completely inorganic PSCs integrated with transition metal dichalcogenide(TMDs; MoS2) materials.

Transformer-less high gain DC–DC converter design and analysis for fuel cell vehicles

High-power converters with significant gains represent established configurations that hold appeal for applications in the industrial and commercial sectors, such as fuel cell electric vehicles (FCEV), energy backup systems, and automotive headlamps. Existing literature predominantly features topologies employing a single-duty ratio. However, this singular approach may not be dependable for operations with high-duty cycles, necessitating the incorporation of additional components to enhance voltage gain. To address this, the current study introduces the concept of time-sharing within the context of a high-gain non-isolated DC–DC converter. This innovative approach achieves substantially higher output voltage gains, approximately 13.33 times that of the input voltage. The analysis of the proposed converter is approached from various perspectives. Finally, it is examined within the MATLAB/Simulink environment, where the theoretical analysis is validated, and an efficiency of 97.4% is achieved.

On Fatigue Damage-Oriented Through-Life Optimization and Control of High-Power IGCT Converters in Wind Energy Systems

Integrated gate commutated thyristors (IGCTs) are critical components in high-voltage, high-current, and high-power conversion systems, particularly in offshore wind energy systems. However, the working environment of offshore wind energy conversion systems is extremely harsh. In this article, we propose an active damage control approach aiming at enhancing the reliability of the conversion system. By employing electro-thermal modeling for the equipment of the offshore wind energy conversion system, the junction temperature and fatigue damage of IGCT are simulated during the operation process. Using the improved model predictive current control (MPCC) method, active damage control effectively regulates the switching frequency of IGCT. IGCTs are symmetrically distributed on each leg of the converter, so the lifespan of the two IGCTs on each leg is also considered to be similar. This method balances the life of the IGCTs on the three legs of the converter and optimizes their utilization to the maximum extent. These measures effectively enhance the reliability of the conversion system and lower the operation and maintenance cost of high-power IGCT converters. The effectiveness of the proposed method is validated by co-simulation results by ANSYS and MATLAB/Simulink.

(Invited) Solving the Energy Storage and Energy Conversion Conundrum – Materials to the Rescue

Energy storage systems have witnessed a meteoric rise ever since Sony commercialized the first Li-ion battery in 1994. Over the years, there have been a plethora of cathode, anode and electrolyte systems developed with stable cycle life and high coulombic efficiencies currently deployed in commercial electric vehicles. Similarly, alternate silicon and tin anodes were targeted as the next generation anodes to ubiquitous carbon. Recalcitrant volume expansion and ensuing solid electrolyte interphase (SEI) issues have reverted the focus back to the omnipresent high-energy density Li metal with efforts to overcome the ominous flammability and safety issues. Escalated impending demand for higher energy density have also made sulfur, an economic and common industrial effluent an attractive active material reverting attention back to Li-S batteries. Similarly, the portentous signs of global warming and the concomitant desire for developing green energy solutions have made hydrogen an imperative and attractive energy source providing the impetus for economic proton exchange membrane (PEM)-based water electrolysis (PEMWE) and fuel cells (PEMFCs). Like the energy storage field, PEMWE and PEMFCs have also witnessed intense research activity over the years following the early work on direct methanol fuel cells (DMFC). Developing high performance materials systems for energy storage and super responsive low-cost electrocatalysts still remain the major conundrum for developing high energy density and high-power density energy storage and conversion systems, respectively.This presentation will discuss the materials challenges that need to be overcome in Li-S batteries and PEM-based water electrolysis and fuel cells. Specifically, efforts aimed at achieving high-energy density cathodes and anodes as well as electrolyte additives for meeting the 500 Whkg-1 energy density targets for electric vehicle technology will be discussed. High sulfur (4-6 mg/cm2) loaded confined cathodes with unique ability to trap the pernicious polysulfide species combined with unique theoretical first principles calculations derived functional electrocatalysts exhibiting the propensity to reversibly catalyze the formation of Li2S and elemental S will be discussed. In tandem, progress made in generating new dendrite-free anodes and low-density current collectors exhibiting areal capacities as high as 15 mAh/cm2 with stable cycling over 100 cycles as well as electrolyte additives matching the cathode and anode performances will be outlined. Similarly, the journey into developing innovative low temperature chemical complexation approaches to novel bifunctional metallic nanostructured electrocatalysts first for DMFC systems and later how the unique approaches were modified targeting acid mediated PEMWE and PEMFCs comprising nanoscale metallic and complex ceramic doped oxide systems will be presented and discussed. Specifically, efforts made in the direction of realizing a unitized regeneration fuel cell (URFC) systems will be outlined and discussed in detail.

Study on Deformation Behavior of Glass in High-temperature Molding for Massive Unit Microlens Arrays.

Microlens arrays (MLAs) with a large number of units, known as massive unit microlens arrays (MUMLAs), are increasingly sought after for their ability to achieve high-power conversion in infrared optical systems. Precision glass molding (PGM) is considered the ideal manufacturing method for MUMLAs. However, the stress distribution and deformation behavior during molding lack detailed understanding, resulting in poor filling consistency and forming accuracy. Consequently, this leads to inconsistent diffuse spot size and irradiance in MUMLAs. This study aims to comprehensively analyze the glass filling behavior during the molding process of MUMLAs using both simulation and experimental approaches. It explains the impact of glass filling behavior and consistency on the optical performance of MUMLAs. Additionally, the effects of molding parameters on the filling consistency of the lenses are investigated. By optimizing these parameters, a high-consistency 128 × 128 MUMLA is fabricated.

Unveiling the potential of bifacial photovoltaics in harvesting indoor light energy: A comprehensive review

Bifacial photovoltaics (BPVs) have received tremendous attention as a potential contender for efficient and cost-effective light energy harvesting. Recently, advancements in BPV technologies have broadened their scope, allowing them to harness artificial indoor light energy efficiently from both top and bottom sides. This innovative approach has demonstrated its effectiveness in energy harvesting through a single-cell design. Among various available PV technologies, thin-film perovskite photovoltaics (PPVs) exhibit exceptional promise for indoor applications in low-light environments. They offer high-power conversion efficiency and ease of design, making them a superior choice when compared to other emerging indoor PV technologies such as kesterite and dye-sensitized PVs. To improve the performance of the indoor BPVs, it is necessary to further review several characteristics relating to their materials, architecture, processing, and indoor characterizations. Additionally, a comprehensive understanding of charge-transfer mechanisms, the variability in indoor lighting sources, the development of standardized indoor simulators, assessment of materials toxicity, and considerations of scalability are essential elements that must be addressed to advance this technology. In summary, this review examines recent developments, emerging trends, challenges, and provide suggestions for the further advancement of i-BPVs, also highlighting their potential as reliable and sustainable indoor energy-harvesting solution.

Buried annealed proton-exchanged waveguide in periodically-poled MgO:LiTaO3 fabricated by surface-activated bonding for high-power wavelength conversion

Watt-class UV laser lights with symmetric spatial modes are suitable for high-resolution industrial applications. Channel waveguides with a guided mode of several ten microns diameter in MgO:LiTaO3 enhance integration capability while avoiding photorefractive damages during high-power wavelength conversion. We focused on buried waveguides fabricated by proton exchange, surface-activated bonding (SAB), and proton diffusion processes in periodically-poled (PP) MgO:LiTaO3. In this work, the mode profiles were simulated using the proton diffusion coefficients estimated by secondary ion mass spectrometry. Using the simulation results, the buried waveguides with a mode diameter larger than 30 μm were fabricated. By adopting designed PP structures, second harmonic generation (SHG) devices at a wavelength of 532 nm were fabricated. The nonlinear coupling coefficient was estimated to be 0.15 W−1/2 cm−1. Compared to the conventional annealed proton-exchanged waveguide SHG device without SAB, symmetric guided modes were obtained while maintaining the nonlinear coupling coefficient.

Monolithic all-perovskite tandem solar cells: advancing sustainable energy options

This paper discusses the results of a simulation-based study on lead-free perovskite tandem devices. Wide bandgap (1.8 eV) perovskite materials Cs2AgBi0.75Sb0.25Br6 as the top cell and narrow bandgap (1.3 eV) perovskite materials CsSnI3 as the bottom cell make up the simulated tandem cell device, respectively. The optimisation process involves individually fine-tuning both cells under standard solar radiation conditions of 100 W/m2. The tandem cells necessitate precise current matching between the two sub-cells. The current matching condition manifests at Jsc of 16 mA cm−2 when the top and bottom cells reach an optimised thickness of 700 nm and 65 nm, respectively. The optimised tandem cell achieves a 24.47% power conversion efficiency (PCE), a high Voc of 1.7278 V, and a high fill factor of 83.72%. Furthermore, tandem solar cells’ temperature dependence is examined in the 300 K to 400 K range, revealing that efficiency decreases with temperature due to a reduction in Jsc (short-circuit current). Notably, the current matching condition is primarily influenced by the top cell, which exhibits less variation than the bottom cell. This study paves the way for developing tandem solar cells made entirely of lead-free perovskites and presents a new approach for the experimental realisation of high-power conversion efficiency.

Enhanced photovoltaic response in WSe2 photodetector with asymmetric two-dimensional contacts

Asymmetric contact pairs with different work functions provide an efficient method to extract photogenerated carriers in optoelectrical devices. Specifically, vertical optoelectrical devices based on two-dimensional (2D) materials utilize graphene layers as the bottom and top contacts. Whereas an additional terminal is required for electrostatic doping in either top or bottom graphene to enlarge the built-in electric field. Herein, we present an enhanced photovoltaic response in a vertical WSe2 photodetector utilizing asymmetric 2D contacts. A graphite layer and a degenerate SnSe2 are used as the top and bottom contacts, respectively, with a significant difference in their work functions. By establishing a large built-in electric field across the vertical WSe2 layer, a strong photovoltaic effect is achieved, resulting in an open-circuit voltage of 0.37 V and a short-circuit current of 0.42 μA under 532 nm illumination. The device shows high-performance photodetection characteristics, with a responsivity of 32.04 A W−1, external quantum efficiency of 7475%, and specific detectivity of 3.61 × 1012 Jones. Furthermore, the device can generate a maximum output electrical power of 70.9 nW, enabling a high-power conversion efficiency of 3.5%.

DFT combined to Boltzmann transport theory for optoelectronic and thermoelectric properties investigations for Se (4 & 8 (at.%)) doped Li2SnS3

Cubic Li2SnS3 emerges as a noteworthy ionic conductor and a viable electrode material for lithium secondary batteries. Its application extends to solar cell technologies, owing to its commendable optoelectronic properties and high-power conversion efficiency. In this study, we present density functional theory (DFT)-based first principles calculations for Li2SnS3-xSex (x = 0, 4, and 8% (atomic percent (at.%)) utilizing the modified Becke Johnson (mBJ) approximations, proposing a compelling alternative. Our investigation reveals significant optical absorption in the ultraviolet region for Li2SnS3-xSex (x = 0, 4, and 8%), accompanied by modest effective mass and indirect band gaps of 2.18 eV for the pristine material. Conversely, doped materials exhibit direct band gaps, with values of 2.113 eV for 4% and 2.026 eV for 8%. Furthermore, the calculated thermoelectric power factor underscores the potential and efficacy of Li2SnS3-xSex in thermoelectric energy devices. The findings not only highlight the material’s promise for solar applications but also underscore its candidacy as a novel solid-state electrolyte for lithium-ion batteries. This stems from its robust thermal stability and notable lithium-ion conductivity, positioning Li2SnS3 as a compelling candidate for advanced energy storage technologies.

Performance analysis of A3B2X9 (Cs3Bi2I9) based perovskite photovoltaic tandem structure with crystalline Silicon (c-Si)

The efficiency of solar cells with single-junction utilizing organic-inorganic hybrid perovskites have attained a value more than 25.5%. The device power conversion efficiency (PCE) can be improved further either by optimizing the absorber layer (Perovskite film) or by investigating the novel device structures such as tandem based solar cells with perovskite and silicon. This combination of top cell (Perovskite solar cell) and bottom cell (Silicon solar cell) can improve the PCE which surpasses the Shockley-Queisser limit of single-junction solar cells by utilizing a wider range of solar spectrum. This paper presents an optimization and simulation of standalone Cs3Bi2I9 perovskite solar cell which was later integrated with a c-Si solar cell to simulate a tandem structure using SCAPS-1D software. The aim is to investigate the performance enhancement of the perovskite solar cell by optimizing it and stacking it on top of a high-efficiency c-Si solar cell using a four-terminal (4T) structure. At a short-circuit current density of 16.165 mA/cm2 and an open-circuit voltage of 1.41 V, the simulation findings demonstrate that the Cs3Bi2I9 perovskite solar cell exhibits a high-power conversion efficiency of 20.37%. The tandem structure demonstrates an enhanced power conversion efficiency of 31.59% which is significantly higher than the efficiency of the individual cells. The Cs3Bi2I9 perovskite solar cell is a great choice for application in tandem systems with c-Si solar cells for high-efficiency, according to the simulation results. This study provides valuable insights for the development of efficient perovskite/c-Si tandem solar cells.

Design and Implementation of GaN-Based Two Switch Flyback With Synchronous Rectification for New Space Applications

This article presents a comprehensive investigation and implementation of a continuous conduction mode pulse width modulated two-switch DC/DC flyback converter utilizing Gallium Nitride Field Effect Transistors (GaNFETs) for New Space applications. The New Space concept advocates for the integration of Commercial Off-The-Shelf (COTS) materials in the space industry. The approach offers cost-effective solutions and reduces lead time for space designs. The study provides steady-state analysis and design considerations for two switch flyback converters, highlighting the transformative capabilities of GaNFETs, especially in high-frequency operations. The rationale behind the preference for GaNFETs over MOSFETs in satellite power supply applications and the strategic benefits of COTS materials are explained in detail. In addition, the synchronous rectification method is implemented to obtain better efficiency, particularly for high-output current operations. The converter achieves an efficiency of over 87% when the load exceeds 50%, with varying input voltages from 20 V to 40 V and a switching frequency of 300 kHz. The experimental findings show that the designed converter can serve as a high efficiency and reliable satellite power converter.