High Nutrient Removal Efficiency Research Articles

Cultivation of yeasts on liquid digestate to remove organic pollutants and nutrients and for potential application as co-culture with microalgae

In this study, the growth of yeast and yeast-like fungi in the liquid digestate from vegetable wastes was investigated in order to remove nutrients and organic pollutants, and for their application as co-culture members with green microalgae. The studied yeast strains were characterized for their assimilative and enzymatic profiles as well as temperature requirements. In the first experimental stage, the growth dynamics of each strain were determined, allowing to select the best yeasts for further studies. In the subsequent stage, the ability of selectants to remove organic pollutants was assessed. Different cultivation media containing respectively 1:3, 1:1, 3:1 vol ratio of liquid digestate and the basal minimal medium were used. Among all tested yeast strains, Rhodotorula mucilaginosa DSM 70825 showed the most promising results, demonstrating the highest potential for removing organic substrates and nutrients. Depending on the medium, this strain achieved 50–80% sCOD, 45–60% tVFAs, 21–45% TN, 33–52% PO43− reduction rates. Similar results were obtained for the strain Candida sp. OR687571. The high nutrient and organics removal efficiency by these yeasts could likely be linked to their ability to assimilate xylose (being the main source of carbon in the liquid digestate). In culture media containing liquid digestate, both yeast strains achieved good viability and proliferation potential. In the liquid digestate medium, R. mucilaginosa and Candida sp. showed vitality at the level of 51.5% and 45.0%, respectively. These strains seem to be a good starting material for developing effective digestate treatment strategies involving monocultures and/or consortia with other yeasts or green microalgae.

A growth phase analysis on the influence of light intensity on microalgal stress and potential biofuel production

It is urgent to find alternatives to fossil fuels to mitigate the effects of climate change. High light intensity during microalgal growth can promote lipid and carbohydrate accumulation (feedstocks to biofuels). However, more research needs to be done concerning the effect of this factor on microalgal productivity and biochemical composition from a growth phase point of view. This study evaluated the impact of high light intensities (291, 527 and 1107 μmol m−2 s−1) on Chlorella vulgaris growth in synthetic wastewater, nutrient assimilation and biochemical composition in late-exponential and stationary growth phases. Under the highest light intensity, a higher growth rate (0.54 ± 0.02 d−1) and maximum productivity (166 ± 13 mg/L d−1) were achieved. Also, nutrient removal efficiencies at the late-exponential phase reached 97.0 ± 0.2 % and 98.2 ± 0.1 % for nitrogen and phosphorus, respectively. Under all light intensities tested at the stationary phase, microalgae also achieved high nutrient removal efficiencies (>95 %). Extreme light intensity (1107 μmol m−2 s−1) boosted the accumulation of carbohydrates (30 ± 3 % w/w) and lipids (13.0 ± 0.4 % w/w). Under lower light intensities, the content of these compounds did not change significantly between growth phases. The chlorophyll content decreased with the increasing light intensity and increasing exposure time. Exposing C. vulgaris to high light intensity seems promising to simultaneously treat wastewater and boost lipid and carbohydrate accumulation, which can be used for biofuel production.

An investigation into the ability of three fungi and one yeast to grow and capture nutrients in cheese whey

This study addresses the environmental and waste disposal challenges dairy processing poses, namely its most nutrient-rich byproduct – whey. Here, the potential of four fungi/yeast species (Geotrichum candidum, Penicillium corylophilum, Penicillium restrictum, Pleurotus ostreatus) was investigated for nutrient reclamation of whey and production of value-added biomass. Conducted in closed and open batch systems, the study evaluates oxygen uptake rates (OUR), biomass yields, and nutrient removal efficiencies at varying mixing speeds. Results show that pellet formation, pH changes, and biomass nutrient content were species-specific. Among the species, P. corylophilum shows promise with high biomass yields (13.21 g DW L−1, 2.0 g/g COD removed) and nutrient removal efficiencies of 26 % COD, 35 % N-tot, and 41 % P-tot. While further optimisation is needed, P. corylophilum shows potential for bioremediation and improved circularity in the dairy industry. Efficacy could be enhanced through bioreactor optimisation, such as employing a continuously fed bubble reactor.

Mechanisms of copper and zinc bioremoval by microalgae and bacteria grown in nutrient rich wastewaters

Swine farming produces large quantities of nutrient-rich wastewater, which often contains metals such as Cu and Zn, used as feed additives for pigs. These metals must be removed from the wastewater before discharge but their retention in the biomass can limit its subsequent utilization. Photobioreactors are a very promising alternative for swine wastewater treatment, as the consortium of microalgae and bacteria growing symbiotically in these reactors allows high nutrient and metal removal efficiency at moderate costs. This work studies the mechanisms of removal of Cu(II) and Zn(II) by the two types of microorganisms growing in these photobioreactors. A microalga commonly used in wastewater treatment (Scenedesmus almeriensis) and an activated sludge were kept in contact with synthetic wastewater containing 100 mg/L of Cu and Zn. After 72 h, Scenedesmus almeriensis removed 43% of Cu and 45% of Zn, while activated sludge removed 78% of Cu and 96% of Zn. Single and sequential extractions of the biomasses using different extracting reagents revealed that biosorption on protonable groups is the dominant removal mechanisms. Mild reagents solubilized 69% of Cu and 94% of Zn from the microalgae and 76% of Cu and 93% of Zn from the activated sludge. Low metal concentrations in the oxidizable and residual fractions evidenced minimal bioaccumulation inside the cells. FTIR and ESEM-EDX analysis confirmed biosorption by ion exchange and complexation as the main metal remediation mechanisms. The weak bonds of the biosorbed Cu and Zn ions are beneficial for the valorization of biomass and the obtaining of safe bioproducts.

Sub-pilot scale sequential microalgal consortium-based cultivation for treatment of municipal wastewater and biomass production

Municipal wastewater (MWW) was treated by a sequential pilot microalgal cultivation process. The cultivation was performed inside a specifically designed low-cost photobioreactor (PBR) system. A microalgal consortium 2:1 was developed using Tetraselmis indica (TS) and Picochlorum sp. (PC) in the first stage and PC:TS (2:1) in the second stage and the nutrient removal efficiency and biomass production and biomolecules production was evaluated and also compared with monoculture in a two-stage sequential cultivation system. This study also investigated the effect of seasonal variations on microalgae growth and MWW treatment. The results showed that mixed microalgal consortium (TS:PC) had higher nutrient removal efficiency, with chemical oxygen demand (COD), total phosphate (TP), and total nitrate (TN) removal efficiencies of 78.50, 84.49, and 84.20%, respectively, and produced a biomass of 2.50 g/L with lipid content of 37.36% in the first stage of cultivation under indoor conditions. In the second stage of indoor cultivation, the PC:TS consortium demonstrated maximum COD, TP, and TN removal efficiencies of 92.49, 94.24, and 94.16%, respectively. It also produced a biomass of 2.65 g/L with a lipid content of 40.67%. Among all the seasonal variations, mass flow analysis indicated that the combination of mixed consortium-based two-stage sequential process during the winter season favored maximum nutrient removal efficiency of TN i.e. 88.54% (84.12 mg/L) and TP i.e., 90.18% (43.29 mg/L), respectively. It also enhanced total biomass production of 49.10 g in 20-L medium, which includes lipid yield ∼15.68 g compared to monoculture i.e., 82.06% (78.70 mg/L) and 82.87% (40.26 mg/L) removal of TN and TP, respectively, and produced biomass 43.60 g with 11.90 g of lipids.

Improved microalgae growth and lipid production in anaerobic digestate with ultraviolet radiation pretreatment

Inappropriate sterilization strategies inhibit microalgal growth when culturing microalgae with anaerobic digestate. This study aimed to scientifically select a low-cost disinfection pretreatment of anaerobic digestate for large-scale microalgae cultivations. In this work, three different methods, including autoclaving, ultraviolet or NaClO treatments, were employed to sterilize the municipal anaerobic digestate. Scenedesmus quadricauda was then cultured in diluted liquid digestate for the simultaneous lipid production and nutrient removal. The results indicated that the growth of S. quadricauda was inhibited after NaClO treatment due to the residual free chlorine. The 15-min ultraviolet effectively mitigated microbial contamination and increasing nutrient availability, enhancing the electron transport of microalgal photosynthesis. After 6-days cultivation, the microalgal biomass concentration of the ultraviolet group was 1.09 g/L, comparable to that of the autoclaving group (1.15 g/L). High nutrient removal efficiency was observed: COD (93.30 %), NH4+-N (92.56 %), TN (85.82 %) and TP (95.12 %). Moreover, S. quadricauda outcompeted the indigenous microorganisms, contributing to its dominance in the culture system of ultraviolet group. The facultative anaerobe Comamonadaceae and aerobes Moraxellaceae, rather than strict anaerobe Paludibacteraceae and Bacteroidetes_vadinHA17, played vital roles in synergistic removal of contaminants by bacteria and algae. The potential competition for nitrogen and phosphorus by bacteria contributed to the ultraviolet group having the greatest lipid content (48.19 %). Therefore, this work suggested using 15-min ultraviolet treatment for anaerobic digestate in large-scale microalgae cultivation.

Application of different aquatic plants in an alternated fill and drain wetland system of Phetchaburi municipal wastewater treatment in Thailand

This study evaluated the treatment efficiency of municipal wastewater from Phetchaburi in Thailand in an alternated 5-day flooding and 2-day drying wetland system with two plants species, namely, Canna indica and Heliconia psittacorum. The efficiencies of biochemical oxygen demand (BOD5) treatment were in the ranges of 90.5% ± 4.8% and 86.9% ± 7.3% for Canna and Heliconia, respectively. Those of chemical oxygen demand (COD) treatment were in the ranges of 75.5% ± 7.9% and 75.3% ± 9.0% for Canna and Heliconia, respectively. Both plants’ removal efficiencies of TN, NH4-N, and TP were greater than 40%. Lead and cadmium accumulation in both plants significantly differed between the upper and lower parts of the plants. However, the lead and cadmium accumulation in Heliconia were greater than their accumulation in Canna. Although Canna had a higher nutrient removal efficiency than Heliconia, there are many varieties of Canna in Thailand. These results indicate that the variety of Canna does not affect the nutrient removal efficiency. In conclusion, a wetland system with alternated flooding and drying conditions can be applied in communities where BOD5 and COD are the dominant wastewater pollution characteristics. Both ornamental plants are suitable absorbents for lead and cadmium, and although the accumulation is lower in Canna than in Heliconia for both heavy metals, the difference was not significant.

Analysis of the growth profile, biochemical composition and nutrient removal efficacy of Spirulina sp. NCIM 5143

In the present manuscript, the growth profile of the microalgae Spirulina sp. NCIM 5143 was studied. Screening was performed on four commercial media, i.e., blue‒green-11 (BG-11), Bold’s basal medium (BBM), algal culture medium (ACM), Zarrouk’s medium (ZM), and different concentrations (20%, 40%, 60%, 80%, and 100%) of unsterilized dairy effluent (UDE). Characterization of biomass was performed to assess its biochemical composition through various assays. Elemental composition and bioactive compound analysis were accomplished by inductively coupled plasma-atomic emission spectroscopy (ICP‒AES) and gas chromatography‒mass spectrometry (GC‒MS), respectively. The results revealed that maximum values of most of the parameters, i.e., optical density (0.21), chlorophyll (2.00 mg/l), proteins (119.17 mg/l), and wet (4.06 g/l) and dry biomass weight (0.28 g/l), were found on ZM. For UDE, maximum growth parameters and the highest nutrient removal efficiency were obtained at 100% concentration. Biochemical analysis revealed that total Kjeldahl nitrogen (7.14±0.49%), crude protein (48.23± 3.34%), total antioxidant activity (3.07±0.03 mg AAE/g), and total phenols (8.88±1.93 mg GAE/g) were present in the biomass. Elemental and GC‒MS analysis detected essential micronutrients and many bioactive compounds, respectively. Hence, this study proved that Spirulina sp. NCIM 5143 has the potential for the management of waste dairy effluent. This study also showed its cost-effectiveness, as the dairy effluent analyzed is used without any kind of sterilization. In addition, its biomass is rich in several essential elements, antioxidants, and bioactive compounds of therapeutic and nutraceutical importance.

Effect of heavy metals in aquaculture water on the growth of microalgae and their migration mechanism in algae-shellfish system

This research the bait microalgae Chlorella sp. and Isochrysis zhangjiangensis were fed to Ruditapes philippinarum (clams) using two types of cultures, monoculture and co-culture, simulating the conditions, and presence, of common heavy metals Cu2+, Pb2+ and Cd2+ in cultured waters. The effects of microalgae growth, antioxidant activity, and changes in nutrient TN and TP were investigated. The metal contents of the culture solution, algal cells, and four tissues of Ruditapes philippinarum were analyzed. The results showed that the highest nutrient removal efficiency was achieved under the co-culture of three heavy metals, with the removal rates of TN and TP ranging from 47.26% to 51.36% and 78.28% to 87.72%, respectively. The higher tolerance of Chlorella sp. to heavy metals compared to Isochrysis zhangjiangensis was probably due to the higher glutathione and super oxide dimutase activities exhibited by Chlorella sp. cells, which increased by 28% and 40.64%, respectively. Isochrysis zhanjiangensis, Chlorella sp. and their co-culture group had the highest removal rate of Pb2+, which were 20.15%, 26.56% and 29.19%, respectively, followed by Cd2+ and Cu2+. The enrichment of the four tissues from the Ruditapes philippinarum organism for heavy metals, was in the order of visceral mass > gill > coat membrane > muscle. The biotransfer coefficients of the three metals in the microalgae-Ruditapes philippinarum food chain biomagnification ranged from 0.24 to 0.79, which indicated that there was no significant biomagnification of the metals in the transfer process of the food chain. The results of this study reveal the mechanism of heavy metal transport in the algae-shellfish system, which would provide a theoretical basis for improving the ecological environment, and can improve the quality of cultured shellfish products.

The efficacy of Vetiveria zizanioides in horizontal subsurface flow constructed wetland for treating textile wastewater

Textile wastewater discharged into rivers often triggers a decrease in water quality and causes harm to its aquatic ecosystem. Textile wastewater, which may contain nutrients, organic compounds, and heavy metals, can be managed using a constructed wetland system. Vetiver grass is known for its ability in treating polluted waters, though the information related to its potential in controlling textile wastewater pollution in riparian areas is still limited. This study aimed to determine the efficacy of a pilot scale constructed wetland system using vetiver grass (Vetiveria zizanioides) for the removal of several pollutants in a riparian area polluted by textile wastewater. The wastewater flowed horizontally through the sub-surface layer of the system with a hydraulic retention time of two days. The wastewater was diluted to 20%. Three systems were made by varying the porous size of planting media using coarse gravel, fine gravel, and sand. The systems were then run for three months. Of the three constructed wetland systems, the highest removal efficiency (RE) was achieved for the NH4 + parameter with an average removal efficiency higher than 60%. The highest nutrient RE was achieved by the system with sand in the growing media, with NH4 + RE of more than 80%. RE values were fluctuating until the end of the experiment, which might occur because the system was not yet stable. It may take longer operation time to get a better system performance in removing the pollutants contained in the textile industry waste.

Enhanced performance of algal-bacterial aerobic granular sludge in comparison to bacterial aerobic granular sludge for treating surfactant-containing wastewater

Increasing amounts of surfactants are used and emitted into the environment due to the COVID-19 pandemic, posing potential threats to ecological health. Algal-bacterial aerobic granular sludge (A-BAGS), with the advantages of compact structure, high-efficient nutrient uptake, and high tolerance to harsh conditions, was attempted in this study to treat surfactant-containing wastewater at relatively high concentrations. The treatment performance was also compared to bacterial AGS (BAGS). Results showed that A-BAGS is preferable for treating wastewater containing a high SDS concentration (30 mg/L), achieving nutrient removal efficiency of 86.3 % for organic carbon, 60.5 % for total nitrogen, and 58.7 % for total phosphorus within a short duration, compared to 70.1 %, 52.8 % and 42.3 % in BAGS reactor. Besides, the removal rate of ammonia nitrogen by A-BAGS was much faster than that of BAGS. The above results confirmed that A-BAGS is a promising technology for treating surfactant-containing wastewater with high nutrient removal efficiency being maintained.

Combination of non-sterilized wastewater purification and high-level CO2 bio-capture with substantial biomass yield of an indigenous Chlorella strain

The indigenous microalga Chlorella sorokiniana NBU-3 grown under air, 5 %, 15 %, and 25 % CO2 supply was evaluated to determine its potential for flue gas bio-capture, nutrient removal capacity and biomass yield using non-sterilized wastewater as growth medium. The results indicated that C. sorokiniana NBU-3 exhibited high nutrient removal efficiency (>95 % for NH4+-N, TN and TP) with either air or CO2 aeration. 5 %–15 % CO2 supplies promote biomass yield, nutrient utilization and CO2 biofixation of C. sorokiniana NBU-3. In particular, 15 % CO2 promotes C. sorokiniana NBU-3 growth in non-sterilized MW, but inhibits its growth in BG11 medium, indicating the importance of non-sterilized MW and high CO2 aeration concurrence for C. sorokiniana NBU-3 economically practical cultivation. Moreover, the highest values of lipid (27.84 ± 2.12 %) and protein (32.65 ± 4.11 %) contents were obtained in MW with 15 % CO2 aeration. Conceivably, microalgal-bacterial symbiosis may help C. sorokiniana NBU-3 tolerate high concentration of CO2 and promote microalga growth. The succession of the community diversity toward the specific functional bacterial species such as Methylobacillus and Methylophilus (Proteobacteria) which were predicted to possess the function of methylotroph, methanol oxidation and ureolysis would help facilitate the microalgal-bacterial symbiosis and promote the microalgae biomass accumulation with high dosage of CO2 aeration. Overall, these findings clearly highlight the potential of this indigenous microalga C. sorokiniana NBU-3 for industrial-emission level CO2 mitigation and commercial microalga biomass production in MW.

Cultivation of Nitrifying and Nitrifying-Denitrifying Aerobic Granular Sludge for Sidestream Treatment of Anaerobically Digested Sludge Centrate

In this study, three 1.2-L aerobic granular sludge sequencing batch reactors (AGS-SBRs) were used to cultivate nitrifying and nitrifying-denitrifying granules (w/supplemental carbon) and investigate sidestream treatment of synthetic-centrate and real-centrate samples from Ashbridges Bay Treatment Plant (ABTP) in Toronto, Ontario, Canada. Results showed that although the cultivation of distinct granules was not observed in the nitrifying reactors, sludge volume index (SVI30) values achieved while treating real and synthetic centrate were 72 ± 12 mL/g and 59 ± 11 mL/g (after day 14), respectively. Ammonia-nitrogen (NH3-N) removal in the nitrifying SBRs were 93 ± 19% and 94 ± 16% for real and synthetic centrate, respectively. Granules with a distinct round structure were successfully formed in the nitrifying-denitrifying SBR, resulting in an SVI30 of 52 ± 23 mL/g. NH3-N, chemical oxygen demand (COD) and phosphorus (P) removal in the nitrifying-denitrifying SBR were 92 ± 9%, 94 ± 5%, and 81 ± 14% (7th to 114th day), respectively with a low nitrite (NO2-N) and nitrate (NO3-N) concentration in the effluent indicating simultaneous nitrification-denitrification (SND) activity. High nutrient removal efficiencies via the nitrification and SND pathways shows that AGS technology is a viable process for treating sidestreams generated in a WWTP.

Balance nitrogen and phosphorus efficient removal under carbon limitation in pilot-scale demonstration of a novel anaerobic/aerobic/anoxic process

Nutrient removal in carbon limited wastewater with high efficiency and energy saving remains a bottleneck for wastewater treatment plants (WWTPs). This study established a pilot-scale anaerobic/aerobic/anoxic (AOA) system with processing capacity of 100 m3/d for the first time. During almost 300 days of stable operation, enhanced nitrogen and phosphorus removal at a C/N of 5 was achieved, and the concentrations of total nitrogen (TN) and total phosphorus (TP) in effluent were 3.60 ± 1.55 and 0.24 ± 0.13 mg/L. Tetrasphaera and Candidatus Competibacter were the dominant phosphorus accumulating organisms (PAOs) and glycogen accumulating organisms (GAOs) in the AOA system. Moreover, the low phosphorus release ensured sufficient intracellular carbon storage by endogenous denitrification, which was the critical factor for nitrogen and phosphorus removal in carbon limited wastewater. The denitrification phosphorus removal (DPR) ability further removed phosphorus and prevented secondary phosphorus release to maintain a low phosphorus concentration in effluent. Finally, rapid start-up, high nutrient removal efficiency and low energy consumption make the proposed AOA process suitable for application in newly constructed and renovated WWTPs.

Tertiary treatment of municipal wastewater by a novel flow constructed wetland integrated with biochar and zero-valent iron

To achieve high and stable nutrient removal efficiency for stricter discharge standards, three bench-scale integrated flow constructed wetlands (IFCWs) with different filler medium arrangements were built for tertiary treatment of municipal wastewater. We hypothesized the incorporation of biochar and zero-valent iron (ZVI) into an IFCW could enhance nutrient removal significantly. Results showed that W2 with biochar (89.1 ± 1.5%, 88.1 ± 1.1%, 75.9 ± 4.5%) and W3 with ZVI-biochar (86.4 ± 1.5%, 88.3 ± 0.7%, 91.6 ± 3.8%) had significantly higher removal efficiencies of NH4+-N, TN, and TP than that of the control group (68.8 ± 7.1%, 62.4 ± 4.6%, 68.1 ± 8.0%). Analysis of the microbial community revealed that nitrifiers such as Nitrosomonadales and Nitrospirales were enriched in W2, while denitrifiers like Rhodocyclales, Burkholderiales, Rhizobiales and Pseudomonadales were enriched in W3. Analysis of functional genes demonstrated that the biochar increased the abundance of AOB-amoA, while ZVI-biochar promoted the abundance of nosZ, nirS, nirK and hzsA. Principal component analysis (PCA) indicated that higher NH4+-N removal efficiency mainly resulted from the enhancement of microbial nitrification by biochar, and the improvement of NO3−-N removal efficiency was attributed to the enhanced denitrification and anammox by ZVI.

Microalgae Chlorella vulgaris and Scenedesmus dimorphus co-cultivation with landfill leachate for pollutant removal and lipid production

In this study, landfill leachate was pre-treated with NaClO, and then diluted to 5%, 10% and 15% for microalgae growth of Chlorella vulgaris and Scenedesmus dimorphus in the mono- and co-culture modes to investigate the nutrient removal and growth characteristics of microalgae. The results revealed that landfill leachate with the 10% dilution rate was conducive for microalgae growth and exhibited robust biomass growth and the highest nutrient removal efficiency. The co-culture biomass in 10% landfill leachate achieved 0.266 g/L within 10 days and demonstrated the improved nutrient utilisation efficiency of microalgae. In addition, the chemical oxygen demand, ammonia nitrogen, total nitrate and total phosphorus removal efficiencies accordingly reached 81.0%, 80.1%, 72.1% and 86.0% in 10% landfill leachate. Meanwhile, both the enzyme activity and fluorescence parameters proved that the cell activity of co-culture was higher than that of mono-culture.

Improved lipid productivity of Scenedesmus obliquus with high nutrient removal efficiency by mixotrophic cultivation in actual municipal wastewater

This study was aimed to assess the growth and lipid productivity improvement of a green microalga Scenedesmus obliquus by mixotrophic cultivation, via addition of sodium acetate (NaAc) into actual municipal wastewater (AMW). Moreover, the nutrient removal efficiency of the culture media in terms of carbon, nitrogen, and phosphorus was investigated. The results showed that the S. obliquus grew better in the AMW than in the BG11 medium (0.20 g L−1 vs 0.16 g L−1 in dry cell weight), and the final algal lipid productivity was higher (9.02 mg L−1 d−1 vs 7.75 mg L−1 d−1, P < 0.05). Further, the addition of NaAc significantly stimulated the algal growth and lipid productivity. Specifically, the highest improvement was obtained by the NaAc-addition of 1 g L−1, where the algal dry cell weight increased 2.40 times than that in the AMW with little organic carbon (0.48 mg L−1 vs 0.20 mg L−1, P < 0.01), and the corresponding algal lipid productivity increased 2.44 time (22.08 mg L−1 d−1 vs 9.02 mg L−1 d−1, P < 0.01). Meanwhile, the addition of 1 g L−1 of NaAc significantly increased the microalga-driven nitrogen and phosphorus removal efficiency, respectively by 1.75 and 2.23 times (82.20% vs 46.85% for total nitrogen, and 76.35% vs 34.18% for total phosphorus). In summary, this study confirmed the feasibility of using organic carbon-supplemented AMW to replace the artificial media for microalgae-based lipid production and nutrient recycling.

MBR공정의 운전조건의 변화에 따른 여과성능 개선연구

Membrane bioreactor (MBR) combining an activated sludge process and membrane filtration could achieve high nutrient removal efficiency and complete biomass retention without a secondary clarifier. Membrane fouling remains the most challenging issue in MBR operation and attracts considerable attention in MBR studies. The objective of this study is to investigate the influence of permeate flux, aeration mode and strength, and mixed liquor suspended solid (MLSS) on membrane filtration of small-scale MBR (the capacity 100㎥/d), which consisted of anaerobic, anoxic, and aeration tank coupled with membrane. Experiments were conducted with real MBR using real wastewater (BOD <250 mg/L, COD <220 mg/L, T-N <65 mg/L, T-P <8 mg/L, E-coli <100,000 no/mL). As a result, the increase of both permeate flux and MLSS increased TMP of MBR while the increase of aeration strength decreased the TMP. Compared to the existing operation conditions of MBR, the operation conditions of shorter filtration time (8 min on/ 2 min off) for a cycle and lower MLSS (<3000 mg/L) in MBR resulted in longer filtration duration time (about two times) as well as the reduction of cleaning chemical.

Investigating emergent macrophytes establishment rate and propagation towards constructed wetlands efficacy optimization

Constructed wetlands have become a widely used tool for reducing nutrient loading from agriculture drainage water running to aquatic ecosystems. To ensure a high nutrient removal efficiency, it is often suggested to use macrophytes to retain or remove nutrients via uptake and through the denitrifying biofilm. In Europe, Phragmites australis and Typha spp are the most commonly used aquatic plants in constructed wetlands (CWs) with free surface flow, and these species often form monocultures in the wetlands. In order to achieve a more diverse vegetation, there is a need to introduce more plant species. Creating a mass production of plant material reduces both handling time and the risk of depleting and disturbing vegetation in natural habitats such as streams or lakes. However, a successful and continuous production of such material during growing seasons requires knowledge of the selected species' establishment and propagation. We examined the relative growth rate (RGR) of six emergent macrophyte species collected from streams and small lakes located in Mid Jutland (Denmark), in seasonal experiments from March to October in order to determine the most efficient time period for their propagation. We found that all species had highest RGR in June, and that several species showed high growth efficiency from April to August. The results showed that it is possible to have a full production of emergent macrophytes throughout the growing season, and therefore, we suggest to propagate plants for use in constructed wetlands in order to enhance biodiversity and ecosystem functioning.

Process-based modeling to assess the nutrient removal efficiency of two endangered hydrophytes: Linking nutrient-cycle with a multiple-quotas approach

Hydrophytes have been widely used to reduce nutrient levels in aquatic ecosystems, but only limited species with high nutrient removal efficiencies have been implemented. Thus, it is necessary to continually explore new candidate species with high nutrient removal efficiencies. To effectively explore the nutrient removal ability of hydrophytes, a new process-based model combining the multiple-quotas approach and nutrient-cycle model was developed. The multiple-quotas approach provides a theoretical framework to conceptually explain the uptake and response of autotrophs to multiple nutrients. The developed process-based model was validated using observational data from microcosm experiments with two emergent hydrophytes, Menyanthes trifoliata and Cicuta virosa. The results showed that both M. trifoliata and C. virosa effectively reduced nitrogen (N) and phosphorus (P) in both water and sediment layers, but M. trifoliata showed a higher removal efficiency for both nutrients than C. virosa, particularly for total ammonia + ammonium-nitrogen (NHx-N) and nitrate-nitrogen (NO3-N) in the sediment layer (M. trifoliata: 0.579–0.976 for NHx-N, 0.567–0.702 for NO3-N; C. virosa: 0.212–0.501 for NHx-N, 0.466–0.560 for NO3-N). In addition, M. trifoliata achieved the maximum removal efficiency for N and P at higher nutrient exposure levels than C. virosa (M. trifoliata: exposure level of 0.725–0.775; C. virosa: exposure level of 0.550–0.575). The developed model well simulated the species-specific growth patterns of hydrophytes depending on the nutrient exposure level as well as the N and P dynamics in the water and sediment layers. The approach adopted in this study provides a useful tool for discovering candidate species to improve hydrophyte diversity and effectively remove nutrients from aquatic ecosystems.